- 09 Dec, 2015 18 commits
-
-
Krzysztof Mazur authored
commit 68accac3 upstream. The commit f5f3497c extended the low identity mapping. However, if the kernel uses more than 2 GB (VMSPLIT_2G_OPT or VMSPLIT_1G memory split), the normal memory mapping is overwritten by the low identity mapping causing a crash. To avoid overwritting, limit the low identity map to cover only memory before kernel range (PAGE_OFFSET). Fixes: f5f3497c "x86/setup: Extend low identity map to cover whole kernel range Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Laszlo Ersek <lersek@redhat.com> Cc: Matt Fleming <matt.fleming@intel.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Link: http://lkml.kernel.org/r/1446815916-22105-1-git-send-email-krzysiek@podlesie.netSigned-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Paolo Bonzini authored
commit f5f3497c upstream. On 32-bit systems, the initial_page_table is reused by efi_call_phys_prolog as an identity map to call SetVirtualAddressMap. efi_call_phys_prolog takes care of converting the current CPU's GDT to a physical address too. For PAE kernels the identity mapping is achieved by aliasing the first PDPE for the kernel memory mapping into the first PDPE of initial_page_table. This makes the EFI stub's trick "just work". However, for non-PAE kernels there is no guarantee that the identity mapping in the initial_page_table extends as far as the GDT; in this case, accesses to the GDT will cause a page fault (which quickly becomes a triple fault). Fix this by copying the kernel mappings from swapper_pg_dir to initial_page_table twice, both at PAGE_OFFSET and at identity mapping. For some reason, this is only reproducible with QEMU's dynamic translation mode, and not for example with KVM. However, even under KVM one can clearly see that the page table is bogus: $ qemu-system-i386 -pflash OVMF.fd -M q35 vmlinuz0 -s -S -daemonize $ gdb (gdb) target remote localhost:1234 (gdb) hb *0x02858f6f Hardware assisted breakpoint 1 at 0x2858f6f (gdb) c Continuing. Breakpoint 1, 0x02858f6f in ?? () (gdb) monitor info registers ... GDT= 0724e000 000000ff IDT= fffbb000 000007ff CR0=0005003b CR2=ff896000 CR3=032b7000 CR4=00000690 ... The page directory is sane: (gdb) x/4wx 0x32b7000 0x32b7000: 0x03398063 0x03399063 0x0339a063 0x0339b063 (gdb) x/4wx 0x3398000 0x3398000: 0x00000163 0x00001163 0x00002163 0x00003163 (gdb) x/4wx 0x3399000 0x3399000: 0x00400003 0x00401003 0x00402003 0x00403003 but our particular page directory entry is empty: (gdb) x/1wx 0x32b7000 + (0x724e000 >> 22) * 4 0x32b7070: 0x00000000 [ It appears that you can skate past this issue if you don't receive any interrupts while the bogus GDT pointer is loaded, or if you avoid reloading the segment registers in general. Andy Lutomirski provides some additional insight: "AFAICT it's entirely permissible for the GDTR and/or LDT descriptor to point to unmapped memory. Any attempt to use them (segment loads, interrupts, IRET, etc) will try to access that memory as if the access came from CPL 0 and, if the access fails, will generate a valid page fault with CR2 pointing into the GDT or LDT." Up until commit 23a0d4e8 ("efi: Disable interrupts around EFI calls, not in the epilog/prolog calls") interrupts were disabled around the prolog and epilog calls, and the functional GDT was re-installed before interrupts were re-enabled. Which explains why no one has hit this issue until now. ] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reported-by: Laszlo Ersek <lersek@redhat.com> Cc: <stable@vger.kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Matt Fleming <matt.fleming@intel.com> [ Updated changelog. ] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Ujfalusi authored
commit 696d8b70 upstream. In case when the interrupt happened for the second eDMA the channel number was incorrectly passed to the client driver. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Florian Fainelli authored
commit d836ace6 upstream. DSA expects the host_dev pointer to be the device structure associated with the MDIO bus controller driver. First commit breaking that was c3a07134 ("mv643xx_eth: convert to use the Marvell Orion MDIO driver"), and then, it got completely under the radar for a while. Reported-by: Frans van de Wiel <fvdw@fvdw.eu> Fixes: c3a07134 ("mv643xx_eth: convert to use the Marvell Orion MDIO driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marek Szyprowski authored
commit 7e312103 upstream. IOMMU-based dma_mmap() implementation lacked proper support for offset parameter used in mmap call (it always assumed that mapping starts from offset zero). This patch adds support for offset parameter to IOMMU-based implementation. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marek Szyprowski authored
commit 371f0f08 upstream. dma_mmap() function in IOMMU-based dma-mapping implementation lacked a check for valid range of mmap parameters (offset and buffer size), what might have caused access beyond the allocated buffer. This patch fixes this issue. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sasha Levin authored
[ Upstream commit 74e98eb0 ] There was no verification that an underlying transport exists when creating a connection, this would cause dereferencing a NULL ptr. It might happen on sockets that weren't properly bound before attempting to send a message, which will cause a NULL ptr deref: [135546.047719] kasan: GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN [135546.051270] Modules linked in: [135546.051781] CPU: 4 PID: 15650 Comm: trinity-c4 Not tainted 4.2.0-next-20150902-sasha-00041-gbaa1222-dirty #2527 [135546.053217] task: ffff8800835bc000 ti: ffff8800bc708000 task.ti: ffff8800bc708000 [135546.054291] RIP: __rds_conn_create (net/rds/connection.c:194) [135546.055666] RSP: 0018:ffff8800bc70fab0 EFLAGS: 00010202 [135546.056457] RAX: dffffc0000000000 RBX: 0000000000000f2c RCX: ffff8800835bc000 [135546.057494] RDX: 0000000000000007 RSI: ffff8800835bccd8 RDI: 0000000000000038 [135546.058530] RBP: ffff8800bc70fb18 R08: 0000000000000001 R09: 0000000000000000 [135546.059556] R10: ffffed014d7a3a23 R11: ffffed014d7a3a21 R12: 0000000000000000 [135546.060614] R13: 0000000000000001 R14: ffff8801ec3d0000 R15: 0000000000000000 [135546.061668] FS: 00007faad4ffb700(0000) GS:ffff880252000000(0000) knlGS:0000000000000000 [135546.062836] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [135546.063682] CR2: 000000000000846a CR3: 000000009d137000 CR4: 00000000000006a0 [135546.064723] Stack: [135546.065048] ffffffffafe2055c ffffffffafe23fc1 ffffed00493097bf ffff8801ec3d0008 [135546.066247] 0000000000000000 00000000000000d0 0000000000000000 ac194a24c0586342 [135546.067438] 1ffff100178e1f78 ffff880320581b00 ffff8800bc70fdd0 ffff880320581b00 [135546.068629] Call Trace: [135546.069028] ? __rds_conn_create (include/linux/rcupdate.h:856 net/rds/connection.c:134) [135546.069989] ? rds_message_copy_from_user (net/rds/message.c:298) [135546.071021] rds_conn_create_outgoing (net/rds/connection.c:278) [135546.071981] rds_sendmsg (net/rds/send.c:1058) [135546.072858] ? perf_trace_lock (include/trace/events/lock.h:38) [135546.073744] ? lockdep_init (kernel/locking/lockdep.c:3298) [135546.074577] ? rds_send_drop_to (net/rds/send.c:976) [135546.075508] ? __might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3795) [135546.076349] ? __might_fault (mm/memory.c:3795) [135546.077179] ? rds_send_drop_to (net/rds/send.c:976) [135546.078114] sock_sendmsg (net/socket.c:611 net/socket.c:620) [135546.078856] SYSC_sendto (net/socket.c:1657) [135546.079596] ? SYSC_connect (net/socket.c:1628) [135546.080510] ? trace_dump_stack (kernel/trace/trace.c:1926) [135546.081397] ? ring_buffer_unlock_commit (kernel/trace/ring_buffer.c:2479 kernel/trace/ring_buffer.c:2558 kernel/trace/ring_buffer.c:2674) [135546.082390] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.083410] ? trace_event_raw_event_sys_enter (include/trace/events/syscalls.h:16) [135546.084481] ? do_audit_syscall_entry (include/trace/events/syscalls.h:16) [135546.085438] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.085515] rds_ib_laddr_check(): addr 36.74.25.172 ret -99 node type -1 Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jason Wang authored
[ Upstream commit 48900cb6 ] virtio declares support for NETIF_F_FRAGLIST, but assumes that there are at most MAX_SKB_FRAGS + 2 fragments which isn't always true with a fraglist. A longer fraglist in the skb will make the call to skb_to_sgvec overflow the sg array, leading to memory corruption. Drop NETIF_F_FRAGLIST so we only get what we can handle. Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric Dumazet authored
[ Upstream commit d69bbf88 ] Only cpu seeing dst refcount going to 0 can safely dereference dst->flags. Otherwise an other cpu might already have freed the dst. Fixes: 27b75c95 ("net: avoid RCU for NOCACHE dst") Reported-by: Greg Thelen <gthelen@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Francesco Ruggeri authored
[ Upstream commit 30f7ea1c ] There is a race conditions between packet_notifier and packet_bind{_spkt}. It happens if packet_notifier(NETDEV_UNREGISTER) executes between the time packet_bind{_spkt} takes a reference on the new netdevice and the time packet_do_bind sets po->ifindex. In this case the notification can be missed. If this happens during a dev_change_net_namespace this can result in the netdevice to be moved to the new namespace while the packet_sock in the old namespace still holds a reference on it. When the netdevice is later deleted in the new namespace the deletion hangs since the packet_sock is not found in the new namespace' &net->packet.sklist. It can be reproduced with the script below. This patch makes packet_do_bind check again for the presence of the netdevice in the packet_sock's namespace after the synchronize_net in unregister_prot_hook. More in general it also uses the rcu lock for the duration of the bind to stop dev_change_net_namespace/rollback_registered_many from going past the synchronize_net following unlist_netdevice, so that no NETDEV_UNREGISTER notifications can happen on the new netdevice while the bind is executing. In order to do this some code from packet_bind{_spkt} is consolidated into packet_do_dev. import socket, os, time, sys proto=7 realDev='em1' vlanId=400 if len(sys.argv) > 1: vlanId=int(sys.argv[1]) dev='vlan%d' % vlanId os.system('taskset -p 0x10 %d' % os.getpid()) s = socket.socket(socket.PF_PACKET, socket.SOCK_RAW, proto) os.system('ip link add link %s name %s type vlan id %d' % (realDev, dev, vlanId)) os.system('ip netns add dummy') pid=os.fork() if pid == 0: # dev should be moved while packet_do_bind is in synchronize net os.system('taskset -p 0x20000 %d' % os.getpid()) os.system('ip link set %s netns dummy' % dev) os.system('ip netns exec dummy ip link del %s' % dev) s.close() sys.exit(0) time.sleep(.004) try: s.bind(('%s' % dev, proto+1)) except: print 'Could not bind socket' s.close() os.system('ip netns del dummy') sys.exit(0) os.waitpid(pid, 0) s.close() os.system('ip netns del dummy') sys.exit(0) Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric Dumazet authored
[ Upstream commit 8fa677d2 ] Under low memory conditions, tcp_sk_init() and icmp_sk_init() can both iterate on all possible cpus and call inet_ctl_sock_destroy(), with eventual NULL pointer. Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ani Sinha authored
[ Upstream commit 44f49dd8 ] Fixes the following kernel BUG : BUG: using __this_cpu_add() in preemptible [00000000] code: bash/2758 caller is __this_cpu_preempt_check+0x13/0x15 CPU: 0 PID: 2758 Comm: bash Tainted: P O 3.18.19 #2 ffffffff8170eaca ffff880110d1b788 ffffffff81482b2a 0000000000000000 0000000000000000 ffff880110d1b7b8 ffffffff812010ae ffff880007cab800 ffff88001a060800 ffff88013a899108 ffff880108b84240 ffff880110d1b7c8 Call Trace: [<ffffffff81482b2a>] dump_stack+0x52/0x80 [<ffffffff812010ae>] check_preemption_disabled+0xce/0xe1 [<ffffffff812010d4>] __this_cpu_preempt_check+0x13/0x15 [<ffffffff81419d60>] ipmr_queue_xmit+0x647/0x70c [<ffffffff8141a154>] ip_mr_forward+0x32f/0x34e [<ffffffff8141af76>] ip_mroute_setsockopt+0xe03/0x108c [<ffffffff810553fc>] ? get_parent_ip+0x11/0x42 [<ffffffff810e6974>] ? pollwake+0x4d/0x51 [<ffffffff81058ac0>] ? default_wake_function+0x0/0xf [<ffffffff810553fc>] ? get_parent_ip+0x11/0x42 [<ffffffff810613d9>] ? __wake_up_common+0x45/0x77 [<ffffffff81486ea9>] ? _raw_spin_unlock_irqrestore+0x1d/0x32 [<ffffffff810618bc>] ? __wake_up_sync_key+0x4a/0x53 [<ffffffff8139a519>] ? sock_def_readable+0x71/0x75 [<ffffffff813dd226>] do_ip_setsockopt+0x9d/0xb55 [<ffffffff81429818>] ? unix_seqpacket_sendmsg+0x3f/0x41 [<ffffffff813963fe>] ? sock_sendmsg+0x6d/0x86 [<ffffffff813959d4>] ? sockfd_lookup_light+0x12/0x5d [<ffffffff8139650a>] ? SyS_sendto+0xf3/0x11b [<ffffffff810d5738>] ? new_sync_read+0x82/0xaa [<ffffffff813ddd19>] compat_ip_setsockopt+0x3b/0x99 [<ffffffff813fb24a>] compat_raw_setsockopt+0x11/0x32 [<ffffffff81399052>] compat_sock_common_setsockopt+0x18/0x1f [<ffffffff813c4d05>] compat_SyS_setsockopt+0x1a9/0x1cf [<ffffffff813c4149>] compat_SyS_socketcall+0x180/0x1e3 [<ffffffff81488ea1>] cstar_dispatch+0x7/0x1e Signed-off-by: Ani Sinha <ani@arista.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Phil Reid authored
[ Upstream commit e6dbe1eb ] priv->hwts_*_en indicate if timestamping is enabled/disabled at run time. But priv->dma_cap.time_stamp and priv->dma_cap.atime_stamp indicates HW is support for PTPv1/PTPv2. Signed-off-by: Phil Reid <preid@electromag.com.au> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Carol L Soto authored
[ Upstream commit c02b0501 ] When doing memcpy/memset of EQEs, we should use sizeof struct mlx4_eqe as the base size and not caps.eqe_size which could be bigger. If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt data in the master context. When using a 64 byte stride, the memcpy copied over 63 bytes to the slave_eq structure. This resulted in copying over the entire eqe of interest, including its ownership bit -- and also 31 bytes of garbage into the next WQE in the slave EQ -- which did NOT include the ownership bit (and therefore had no impact). However, once the stride is increased to 128, we are overwriting the ownership bits of *three* eqes in the slave_eq struct. This results in an incorrect ownership bit for those eqes, which causes the eq to seem to be full. The issue therefore surfaced only once 128-byte EQEs started being used in SRIOV and (overarchitectures that have 128/256 byte cache-lines such as PPC) - e.g after commit 77507aa2 "net/mlx4_core: Enable CQE/EQE stride support". Fixes: 08ff3235 ('mlx4: 64-byte CQE/EQE support') Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sowmini Varadhan authored
[ Upstream commit 8ce675ff ] Either of pskb_pull() or pskb_trim() may fail under low memory conditions. If rds_tcp_data_recv() ignores such failures, the application will receive corrupted data because the skb has not been correctly carved to the RDS datagram size. Avoid this by handling pskb_pull/pskb_trim failure in the same manner as the skb_clone failure: bail out of rds_tcp_data_recv(), and retry via the deferred call to rds_send_worker() that gets set up on ENOMEM from rds_tcp_read_sock() Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Guillaume Nault authored
[ Upstream commit 1acea4f6 ] We can't rely on PPPOX_ZOMBIE to decide whether to clear po->pppoe_dev. PPPOX_ZOMBIE can be set by pppoe_disc_rcv() even when po->pppoe_dev is NULL. So we have no guarantee that (sk->sk_state & PPPOX_ZOMBIE) implies (po->pppoe_dev != NULL). Since we're releasing a PPPoE socket, we want to release the pppoe_dev if it exists and reset sk_state to PPPOX_DEAD, no matter the previous value of sk_state. So we can just check for po->pppoe_dev and avoid any assumption on sk->sk_state. Fixes: 2b018d57 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jason Wang authored
[ Upstream commit f23d538b ] We don't have fraglist support in TAP_FEATURES. This will lead software segmentation of gro skb with frag list. Fixes by having frag list support in TAP_FEATURES. With this patch single session of netperf receiving were restored from about 5Gb/s to about 12Gb/s on mlx4. Fixes a567dd62 ("macvtap: simplify usage of tap_features") Cc: Vlad Yasevich <vyasevic@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dan Carpenter authored
[ Upstream commit 50010c20 ] This is decrementing the pointer, instead of the value stored in the pointer. KASan detects it as an out of bounds reference. Reported-by: "Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 09 Nov, 2015 22 commits
-
-
Greg Kroah-Hartman authored
-
Dan Carpenter authored
commit 59c816c1 upstream. This code in vhost_scsi_make_tpg() is confusing because we limit "tpgt" to UINT_MAX but the data type of "tpg->tport_tpgt" and that is a u16. I looked at the context and it turns out that in vhost_scsi_set_endpoint(), "tpg->tport_tpgt" is used as an offset into the vs_tpg[] array which has VHOST_SCSI_MAX_TARGET (256) elements so anything higher than 255 then it is invalid. I have made that the limit now. In vhost_scsi_send_evt() we mask away values higher than 255, but now that the limit has changed, we don't need the mask. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Cc: Ray Yang <ray.yang@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Greg Kroah-Hartman authored
Fixes the backport of 0b34a166 upstream Commit 0b34a166 "x86/xen: Support kexec/kdump in HVM guests by doing a soft reset" has been added to the 4.2-stable tree" needed to correct the CONFIG variable, as CONFIG_KEXEC_CORE only showed up in 4.3. Reported-by: David Vrabel <david.vrabel@citrix.com> Reported-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Soeren Grunewald authored
commit be32c0cf upstream. The Exar XR17V358 can also be combined with a XR17V354 chip to act as a single 12 port chip. This works the same way as the combining two XR17V358 chips. But the reported device id then is 0x4358. Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Soeren Grunewald authored
commit 96a5d18b upstream. The Exar XR17V358 chip usually provides only 8 ports. But two chips can be combined to act as a single 16 port chip. Therefor one chip is configured as master the second as slave by connecting the mode pin to VCC (master) or GND (slave). Then the master chip is reporting a different device-id depending on whether a slave is detected or not. The UARTs 8-15 are addressed from 0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to address all 16 ports as before. See: https://www.exar.com/common/content/document.ashx?id=1587 page 11 Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Roman Gushchin authored
commit b8a9d66d upstream. After commit 566c09c5 ("raid5: relieve lock contention in get_active_stripe()") __find_stripe() is called under conf->hash_locks + hash. But handle_stripe_clean_event() calls remove_hash() under conf->device_lock. Under some cirscumstances the hash chain can be circuited, and we get an infinite loop with disabled interrupts and locked hash lock in __find_stripe(). This leads to hard lockup on multiple CPUs and following system crash. I was able to reproduce this behavior on raid6 over 6 ssd disks. The devices_handle_discard_safely option should be set to enable trim support. The following script was used: for i in `seq 1 32`; do dd if=/dev/zero of=large$i bs=10M count=100 & done neilb: original was against a 3.x kernel. I forward-ported to 4.3-rc. This verison is suitable for any kernel since Commit: 59fc630b ("RAID5: batch adjacent full stripe write") (v4.1+). I'll post a version for earlier kernels to stable. Signed-off-by: Roman Gushchin <klamm@yandex-team.ru> Fixes: 566c09c5 ("raid5: relieve lock contention in get_active_stripe()") Signed-off-by: NeilBrown <neilb@suse.com> Cc: Shaohua Li <shli@kernel.org> Cc: <stable@vger.kernel.org> # 3.13 - 4.2 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Doron Tsur authored
commit 0ca81a28 upstream. ib_send_cm_sidr_rep could sometimes erase the node from the sidr (depending on errors in the process). Since ib_send_cm_sidr_rep is called both from cm_sidr_req_handler and cm_destroy_id, cm_id_priv could be either erased from the rb_tree twice or not erased at all. Fixing that by making sure it's erased only once before freeing cm_id_priv. Fixes: a977049d ('[PATCH] IB: Add the kernel CM implementation') Signed-off-by: Doron Tsur <doront@mellanox.com> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dāvis Mosāns authored
commit 22805217 upstream. When pci_pool_alloc fails in mvs_task_prep then task->lldd_task stays NULL but it's later used in mvs_abort_task as slot which is passed to mvs_slot_task_free causing NULL pointer dereference. Just return from mvs_slot_task_free when passed with NULL slot. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101891Signed-off-by: Dāvis Mosāns <davispuh@gmail.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
NeilBrown authored
commit d01552a7 upstream. This reverts commit 7eb41885. This commit is poorly justified, I can find not discusison in email, and it clearly causes a problem. If a device which is being recovered fails and is subsequently re-added to an array, there could easily have been changes to the array *before* the point where the recovery was up to. So the recovery must start again from the beginning. If a spare is being recovered and fails, then when it is re-added we really should do a bitmap-based recovery up to the recovery-offset, and then a full recovery from there. Before this reversion, we only did the "full recovery from there" which is not corect. After this reversion with will do a full recovery from the start, which is safer but not ideal. It will be left to a future patch to arrange the two different styles of recovery. Reported-and-tested-by: Nate Dailey <nate.dailey@stratus.com> Signed-off-by: NeilBrown <neilb@suse.com> Fixes: 7eb41885 ("md: allow a partially recovered device to be hot-added to an array.") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jes Sorensen authored
commit 681ab469 upstream. This was introduced with 9e882242 which changed the return value of submit_bio_wait() to return != 0 on error, but didn't update the caller accordingly. Fixes: 9e882242 ("block: Add submit_bio_wait(), remove from md") Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com> Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jes Sorensen authored
commit 203d27b0 upstream. This was introduced with 9e882242 which changed the return value of submit_bio_wait() to return != 0 on error, but didn't update the caller accordingly. Fixes: 9e882242 ("block: Add submit_bio_wait(), remove from md") Reported-by: Bill Kuzeja <William.Kuzeja@stratus.com> Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Herbert Xu authored
commit 3fc89adb upstream. Currently a number of Crypto API operations may fail when a signal occurs. This causes nasty problems as the caller of those operations are often not in a good position to restart the operation. In fact there is currently no need for those operations to be interrupted by user signals at all. All we need is for them to be killable. This patch replaces the relevant calls of signal_pending with fatal_signal_pending, and wait_for_completion_interruptible with wait_for_completion_killable, respectively. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Peter Zijlstra authored
commit 275d7d44 upstream. Poma (on the way to another bug) reported an assertion triggering: [<ffffffff81150529>] module_assert_mutex_or_preempt+0x49/0x90 [<ffffffff81150822>] __module_address+0x32/0x150 [<ffffffff81150956>] __module_text_address+0x16/0x70 [<ffffffff81150f19>] symbol_put_addr+0x29/0x40 [<ffffffffa04b77ad>] dvb_frontend_detach+0x7d/0x90 [dvb_core] Laura Abbott <labbott@redhat.com> produced a patch which lead us to inspect symbol_put_addr(). This function has a comment claiming it doesn't need to disable preemption around the module lookup because it holds a reference to the module it wants to find, which therefore cannot go away. This is wrong (and a false optimization too, preempt_disable() is really rather cheap, and I doubt any of this is on uber critical paths, otherwise it would've retained a pointer to the actual module anyway and avoided the second lookup). While its true that the module cannot go away while we hold a reference on it, the data structure we do the lookup in very much _CAN_ change while we do the lookup. Therefore fix the comment and add the required preempt_disable(). Reported-by: poma <pomidorabelisima@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Fixes: a6e6abd5 ("module: remove module_text_address()") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Cathy Avery authored
commit a54c8f0f upstream. xen-blkfront will crash if the check to talk_to_blkback() in blkback_changed()(XenbusStateInitWait) returns an error. The driver data is freed and info is set to NULL. Later during the close process via talk_to_blkback's call to xenbus_dev_fatal() the null pointer is passed to and dereference in blkfront_closing. Signed-off-by: Cathy Avery <cathy.avery@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Laura Abbott authored
commit fd7cd061 upstream. We received several reports of systems rebooting and powering on after an attempted shutdown. Testing showed that setting XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT quirk allowed the system to shutdown as expected for LynxPoint-LP xHCI controllers. Set the quirk back. Note that the quirk was originally introduced for LynxPoint and LynxPoint-LP just for this same reason. See: commit 638298dc ("xhci: Fix spurious wakeups after S5 on Haswell") It was later limited to only concern HP machines as it caused regression on some machines, see both bug and commit: Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171 commit 6962d914 ("xhci: Limit the spurious wakeup fix only to HP machines") Later it was discovered that the powering on after shutdown was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP machine suffered from spontaneous resume from S3 (which should not be related to the SPURIOUS_WAKEUP quirk at all). An attempt to fix this then removed the SPURIOUS_WAKEUP flag usage completely. commit b45abacd ("xhci: no switching back on non-ULT Haswell") Current understanding is that LynxPoint-LP (Haswell ULT) machines need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and plain Lynxpoint (Haswell) machines may _not_ have the quirk set otherwise they again will restart. Signed-off-by: Laura Abbott <labbott@fedoraproject.org> Cc: Takashi Iwai <tiwai@suse.de> Cc: Oliver Neukum <oneukum@suse.com> [Added more history to commit message -Mathias] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Nyman authored
commit 3b4739b8 upstream. If a host fails to wake up a isochronous SuperSpeed device from U1/U2 in time for a isoch transfer it will generate a "No ping response error" Host will then move to the next transfer descriptor. Handle this case in the same way as missed service errors, tag the current TD as skipped and handle it on the next transfer event. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mike Snitzer authored
commit 4dcb8b57 upstream. btree_split_beneath()'s error path had an outstanding FIXME that speaks directly to the potential for _not_ cleaning up a previously allocated bufio-backed block. Fix this by releasing the previously allocated bufio block using unlock_block(). Reported-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joe Thornber authored
commit 2871c69e upstream. Commit 4c7e3093 ("dm btree remove: fix bug in redistribute3") wasn't a complete fix for redistribute3(). The redistribute3 function takes 3 btree nodes and shares out the entries evenly between them. If the three nodes in total contained (MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in the center. Fix this issue by being more careful about calculating the target number of entries for the left and right nodes. Unit tested in userspace using this program: https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.cSigned-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Will Deacon authored
commit 9702970c upstream. This reverts commit e306dfd0. With this patch applied, we were the only architecture making this sort of adjustment to the PC calculation in the unwinder. This causes problems for ftrace, where the PC values are matched against the contents of the stack frames in the callchain and fail to match any records after the address adjustment. Whilst there has been some effort to change ftrace to workaround this, those patches are not yet ready for mainline and, since we're the odd architecture in this regard, let's just step in line with other architectures (like arch/arm/) for now. Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ilya Dryomov authored
commit 6d69bb53 upstream. Mapping an image with a long parent chain (e.g. image foo, whose parent is bar, whose parent is baz, etc) currently leads to a kernel stack overflow, due to the following recursion in the reply path: rbd_osd_req_callback() rbd_obj_request_complete() rbd_img_obj_callback() rbd_img_parent_read_callback() rbd_obj_request_complete() ... Limit the parent chain to 16 images, which is ~5K worth of stack. When the above recursion is eliminated, this limit can be lifted. Fixes: http://tracker.ceph.com/issues/12538Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Josh Durgin <jdurgin@redhat.com> [idryomov@gmail.com: backport to 3.14: rbd_dev->opts, context] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ilya Dryomov authored
commit 1f2c6651 upstream. Currently we leak parent_spec and trigger a "parent reference underflow" warning if rbd_dev_create() in rbd_dev_probe_parent() fails. The problem is we take the !parent out_err branch and that only drops refcounts; parent_spec that would've been freed had we called rbd_dev_unparent() remains and triggers rbd_warn() in rbd_dev_parent_put() - at that point we have parent_spec != NULL and parent_ref == 0, so counter ends up being -1 after the decrement. Redo rbd_dev_probe_parent() to fix this. Signed-off-by: Ilya Dryomov <idryomov@gmail.com> [idryomov@gmail.com: backport to < 4.2: rbd_dev->opts] Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ronny Hegewald authored
commit bae818ee upstream. rbd requires stable pages, as it performs a crc of the page data before they are send to the OSDs. But since kernel 3.9 (patch 1d1d1a76 "mm: only enforce stable page writes if the backing device requires it") it is not assumed anymore that block devices require stable pages. This patch sets the necessary flag to get stable pages back for rbd. In a ceph installation that provides multiple ext4 formatted rbd devices "bad crc" messages appeared regularly (ca 1 message every 1-2 minutes on every OSD that provided the data for the rbd) in the OSD-logs before this patch. After this patch this messages are pretty much gone (only ca 1-2 / month / OSD). Signed-off-by: Ronny Hegewald <Ronny.Hegewald@online.de> [idryomov@gmail.com: require stable pages only in crc case, changelog] [idryomov@gmail.com: backport to 3.9-3.17: context] Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-