Enable CPU opp tables for Tanix TX6.

Also add the fixed regulator that provided vdd-cpu-gpu required for
CPU opp tables.

This voltage has been found using a voltmeter and could be wrong.
Tested-by: Jernej Škrabec <jernej.skrabec@gmail.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Some boards have a fixed regulator and can't reach the voltage set
by the OPP table.

Add a range where the minimal voltage is the target and the maximal
voltage is 1.2V.
Suggested-by: Ondřej Jirman <megous@megous.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The binding specifies #address-cells and #size-cells should be present.
Without them present, dtc issues a warning because default for
#address-cells seems to be <2>:

arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi:1108.4-52:
  Warning (dma_ranges_format):
    /soc/dram-controller@1c62000:dma-ranges:
    "dma-ranges" property has invalid length (12 bytes)
    (parent #address-cells == 1, child #address-cells == 2,
    #size-cells == 1)

mbus #address-cells should be 1.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Enable CPU and GPU opp tables for Pine H64.

This needs to change the CPU regulator max voltage to fit
the OPP table.

Also add the ramp-delay information to avoid any out of spec
running as the regulator is slower at reaching the voltage
requested compare to the PLL reaching the frequency.

There is no such information for AXP805 but similar PMIC (AXP813)
has a DVM (Dynamic Voltage scaling Management) ramp rate equal
to 2500uV/us.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Pine H64 device-tree have some nodes not properly sorted.

Fix this.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Enable CPU opp tables for Orange Pi 3.

This needs to change the CPU regulator max voltage to fit
the OPP table.

Also add the ramp-delay information to avoid any out of spec
running as the regulator is slower at reaching the voltage
requested compare to the PLL reaching the frequency.

There is no such information for AXP805 but similar PMIC (AXP813)
has a DVM (Dynamic Voltage scaling Management) ramp rate equal
to 2500uV/us.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Enable CPU opp tables for Beelink GS1.

This needs to change the CPU regulator max voltage to fit
the OPP table.

Also add the ramp-delay information to avoid any out of spec
running as the regulator is slower at reaching the voltage
requested compare to the PLL reaching the frequency.

There is no such information for AXP805 but similar PMIC (AXP813)
has a DVM (Dynamic Voltage scaling Management) ramp rate equal
to 2500uV/us.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Add an Operating Performance Points table for the CPU cores to
enable Dynamic Voltage & Frequency Scaling on the H6.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

This enables passive cooling by down-regulating CPU voltage
and frequency.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The ARM CPU cores are fed by the CPU clock from the CCU. Add a
reference to the clock for each CPU core, along with the clock
transition latency.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

OrangePi Lite2 has AP6255 BT+WIFI combo chip. Add support for it.
Signed-off-by: Sebastian Meyer <git-commit@mailhell.seb7.de>
[merged BT and WIFI patches and updated commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

As can be seen from OrangePi Lite 2 and One Plus schematics, VBUS pin on
USB OTG port is directly connected to 5 V power supply. This mean that
OTG port can safely operate only in host mode, even though these two
boards have ID pin connected.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

OrangePi Lite2 and One Plus have GPIO ports powered by same power
supplies. Add them in common DT.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The PWR-LED on the bananapi m2 zero board is on when gpio PL10 is low.
This has been verified on a board and in the schematics [1].

[1]: http://wiki.banana-pi.org/Banana_Pi_BPI-M2_ZERO#Documents

Fixes: 8b8061fc ("ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The H6 SoC contains a message box that can be used to send messages and
interrupts back and forth between the ARM application CPUs and the ARISC
coprocessor. Add a device tree node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The A64 SoC contains a message box that can be used to send messages and
interrupts back and forth between the ARM application CPUs and the ARISC
coprocessor. Add a device tree node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The H3 and H5 SoCs contain a message box that can be used to send
messages and interrupts back and forth between the ARM application CPUs
and the ARISC coprocessor. Add a device tree node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The A83T SoC contains a message box that can be used to send messages
and interrupts back and forth between the ARM application CPUs and the
ARISC coprocessor. Add a device tree node for it.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

OPP table value is get from orangepi lichee linux-3.4
kernel driver.
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

There is a red LED marked as `GPIO_LED1` on the silkscreen and connected
to PE17 by default. So lets add this missing bit in the current hardware
description.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

There is new version of A20-OLinuXino-LIME with eMMC storage. The
card routing is the same as in A20-OLinuXino-LIME2-eMMC, so this
is basically copy/paste.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Add compatible string for A20-OLinuXino-LIME2-eMMC to the
bindings documentation.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

This sorts the actual field names too, potentially causing even more
chaos and confusion at merge time if you have edited the MAINTAINERS
file.  But the end result is a more consistent layout, and hopefully
it's a one-time pain minimized by doing this just before the -rc1
release.

This was entirely scripted:

  ./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS --order
Requested-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

They are all supposed to be sorted, but people who add new entries don't
always know the alphabet.  Plus sometimes the entry names get edited,
and people don't then re-order the entry.

Let's see how painful this will be for merging purposes (the MAINTAINERS
file is often edited in various different trees), but Joe claims there's
relatively few patches in -next that touch this, and doing it just
before -rc1 is likely the best time.  Fingers crossed.

This was scripted with

  /scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS

but then I also ended up manually upper-casing a few entry names that
stood out when looking at the end result.
Requested-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull x86 fixes from Thomas Gleixner:
 "A set of three patches to fix the fallout of the newly added split
  lock detection feature.

  It addressed the case where a KVM guest triggers a split lock #AC and
  KVM reinjects it into the guest which is not prepared to handle it.

  Add proper sanity checks which prevent the unconditional injection
  into the guest and handles the #AC on the host side in the same way as
  user space detections are handled. Depending on the detection mode it
  either warns and disables detection for the task or kills the task if
  the mode is set to fatal"

* tag 'x86-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  KVM: VMX: Extend VMXs #AC interceptor to handle split lock #AC in guest
  KVM: x86: Emulate split-lock access as a write in emulator
  x86/split_lock: Provide handle_guest_split_lock()

Pull time(keeping) updates from Thomas Gleixner:

 - Fix the time_for_children symlink in /proc/$PID/ so it properly
   reflects that it part of the 'time' namespace

 - Add the missing userns limit for the allowed number of time
   namespaces, which was half defined but the actual array member was
   not added. This went unnoticed as the array has an exessive empty
   member at the end but introduced a user visible regression as the
   output was corrupted.

 - Prevent further silent ucount corruption by adding a BUILD_BUG_ON()
   to catch half updated data.

* tag 'timers-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ucount: Make sure ucounts in /proc/sys/user don't regress again
  time/namespace: Add max_time_namespaces ucount
  time/namespace: Fix time_for_children symlink

Pull scheduler fixes/updates from Thomas Gleixner:

 - Deduplicate the average computations in the scheduler core and the
   fair class code.

 - Fix a raise between runtime distribution and assignement which can
   cause exceeding the quota by up to 70%.

 - Prevent negative results in the imbalanace calculation

 - Remove a stale warning in the workqueue code which can be triggered
   since the call site was moved out of preempt disabled code. It's a
   false positive.

 - Deduplicate the print macros for procfs

 - Add the ucmap values to the SCHED_DEBUG procfs output for completness

* tag 'sched-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Add task uclamp values to SCHED_DEBUG procfs
  sched/debug: Factor out printing formats into common macros
  sched/debug: Remove redundant macro define
  sched/core: Remove unused rq::last_load_update_tick
  workqueue: Remove the warning in wq_worker_sleeping()
  sched/fair: Fix negative imbalance in imbalance calculation
  sched/fair: Fix race between runtime distribution and assignment
  sched/fair: Align rq->avg_idle and rq->avg_scan_cost

Pull perf fixes from Thomas Gleixner:
 "Three fixes/updates for perf:

   - Fix the perf event cgroup tracking which tries to track the cgroup
     even for disabled events.

   - Add Ice Lake server support for uncore events

   - Disable pagefaults when retrieving the physical address in the
     sampling code"

* tag 'perf-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Disable page faults when getting phys address
  perf/x86/intel/uncore: Add Ice Lake server uncore support
  perf/cgroup: Correct indirection in perf_less_group_idx()
  perf/core: Fix event cgroup tracking

Pull locking fixes from Thomas Gleixner:
 "Three small fixes/updates for the locking core code:

   - Plug a task struct reference leak in the percpu rswem
     implementation.

   - Document the refcount interaction with PID_MAX_LIMIT

   - Improve the 'invalid wait context' data dump in lockdep so it
     contains all information which is required to decode the problem"

* tag 'locking-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/lockdep: Improve 'invalid wait context' splat
  locking/refcount: Document interaction with PID_MAX_LIMIT
  locking/percpu-rwsem: Fix a task_struct refcount

Pull cifs fixes from Steve French:
 "Ten cifs/smb fixes:

   - five RDMA (smbdirect) related fixes

   - add experimental support for swap over SMB3 mounts

   - also a fix which improves performance of signed connections"

* tag '5.7-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: enable swap on SMB3 mounts
  smb3: change noisy error message to FYI
  smb3: smbdirect support can be configured by default
  cifs: smbd: Do not schedule work to send immediate packet on every receive
  cifs: smbd: Properly process errors on ib_post_send
  cifs: Allocate crypto structures on the fly for calculating signatures of incoming packets
  cifs: smbd: Update receive credits before sending and deal with credits roll back on failure before sending
  cifs: smbd: Check send queue size before posting a send
  cifs: smbd: Merge code to track pending packets
  cifs: ignore cached share root handle closing errors

Pull NFS client bugfix from Trond Myklebust:
 "Fix an RCU read lock leakage in pnfs_alloc_ds_commits_list()"

* tag 'nfs-for-5.7-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  pNFS: Fix RCU lock leakage

Pull nios2 updates from Ley Foon Tan:

 - Remove nios2-dev@lists.rocketboards.org from MAINTAINERS

 - remove 'resetvalue' property

 - rename 'altr,gpio-bank-width' -> 'altr,ngpio'

 - enable the common clk subsystem on Nios2

* tag 'nios2-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
  MAINTAINERS: Remove nios2-dev@lists.rocketboards.org
  arch: nios2: remove 'resetvalue' property
  arch: nios2: rename 'altr,gpio-bank-width' -> 'altr,ngpio'
  arch: nios2: Enable the common clk subsystem on Nios2

Pull dma-mapping fixes from Christoph Hellwig:

 - fix an integer truncation in dma_direct_get_required_mask
   (Kishon Vijay Abraham)

 - fix the display of dma mapping types (Grygorii Strashko)

* tag 'dma-mapping-5.7-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-debug: fix displaying of dma allocation type
  dma-direct: fix data truncation in dma_direct_get_required_mask()

Pull more Kbuild updates from Masahiro Yamada:

 - raise minimum supported binutils version to 2.23

 - remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports

 - move remaining CONFIG_AS_* tests to Kconfig from Makefile

 - enable -Wtautological-compare warnings to catch more issues

 - do not support GCC plugins for GCC <= 4.7

 - fix various breakages of 'make xconfig'

 - include the linker version used for linking the kernel into
   LINUX_COMPILER, which is used for the banner, and also exposed to
   /proc/version

 - link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which
   allows us to remove the lib-ksyms.o workaround, and to solve the last
   known issue of the LLVM linker

 - add dummy tools in scripts/dummy-tools/ to enable all compiler tests
   in Kconfig, which will be useful for distro maintainers

 - support the single switch, LLVM=1 to use Clang and all LLVM utilities
   instead of GCC and Binutils.

 - support LLVM_IAS=1 to enable the integrated assembler, which is still
   experimental

* tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits)
  kbuild: fix comment about missing include guard detection
  kbuild: support LLVM=1 to switch the default tools to Clang/LLVM
  kbuild: replace AS=clang with LLVM_IAS=1
  kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig
  kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y
  MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory
  kbuild: remove -I$(srctree)/tools/include from scripts/Makefile
  kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h
  Documentation/llvm: fix the name of llvm-size
  kbuild: mkcompile_h: Include $LD version in /proc/version
  kconfig: qconf: Fix a few alignment issues
  kconfig: qconf: remove some old bogus TODOs
  kconfig: qconf: fix support for the split view mode
  kconfig: qconf: fix the content of the main widget
  kconfig: qconf: Change title for the item window
  kconfig: qconf: clean deprecated warnings
  gcc-plugins: drop support for GCC <= 4.7
  kbuild: Enable -Wtautological-compare
  x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2
  crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean'
  ...

I do not longer work for credativ Germany.

Please, use my private email address instead.

This is for the case when people want to CC me on
patches sent from my old business email address.
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Another brown paper bag moment. pnfs_alloc_ds_commits_list() is leaking
the RCU lock.

Fixes: a9901899 ("pNFS: Add infrastructure for cleaning up per-layout commit structures")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

Two types of #AC can be generated in Intel CPUs:
 1. legacy alignment check #AC
 2. split lock #AC

Reflect #AC back into the guest if the guest has legacy alignment checks
enabled or if split lock detection is disabled.

If the #AC is not a legacy one and split lock detection is enabled, then
invoke handle_guest_split_lock() which will either warn and disable split
lock detection for this task or force SIGBUS on it.

[ tglx: Switch it to handle_guest_split_lock() and rename the misnamed
  helper function. ]
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/r/20200410115517.176308876@linutronix.de

Emulate split-lock accesses as writes if split lock detection is on
to avoid #AC during emulation, which will result in a panic(). This
should never occur for a well-behaved guest, but a malicious guest can
manipulate the TLB to trigger emulation of a locked instruction[1].

More discussion can be found at [2][3].

[1] https://lkml.kernel.org/r/8c5b11c9-58df-38e7-a514-dc12d687b198@redhat.com
[2] https://lkml.kernel.org/r/20200131200134.GD18946@linux.intel.com
[3] https://lkml.kernel.org/r/20200227001117.GX9940@linux.intel.comSuggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/r/20200410115517.084300242@linutronix.de

Without at least minimal handling for split lock detection induced #AC,
VMX will just run into the same problem as the VMWare hypervisor, which
was reported by Kenneth.

It will inject the #AC blindly into the guest whether the guest is
prepared or not.

Provide a function for guest mode which acts depending on the host
SLD mode. If mode == sld_warn, treat it like user space, i.e. emit a
warning, disable SLD and mark the task accordingly. Otherwise force
SIGBUS.

 [ bp: Add a !CPU_SUP_INTEL stub for handle_guest_split_lock(). ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/r/20200410115516.978037132@linutronix.de
Link: https://lkml.kernel.org/r/20200402123258.895628824@linutronix.de