Pull networking fixes from Paolo Abeni:
 "Including fixes from xfrm and can.

  Current release - regressions:

   - rxrpc: restore removed timer deletion

  Current release - new code bugs:

   - gre: fix device lookup for l3mdev use-case

   - xfrm: fix egress device lookup for l3mdev use-case

  Previous releases - regressions:

   - sched: cls_u32: fix netns refcount changes in u32_change()

   - smc: fix sock leak when release after smc_shutdown()

   - xfrm: limit skb_page_frag_refill use to a single page

   - eth: atlantic: invert deep par in pm functions, preventing null
     derefs

   - eth: stmmac: use readl_poll_timeout_atomic() in atomic state

  Previous releases - always broken:

   - gre: fix skb_under_panic on xmit

   - openvswitch: fix OOB access in reserve_sfa_size()

   - dsa: hellcreek: calculate checksums in tagger

   - eth: ice: fix crash in switchdev mode

   - eth: igc:
      - fix infinite loop in release_swfw_sync
      - fix scheduling while atomic"

* tag 'net-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
  drivers: net: hippi: Fix deadlock in rr_close()
  selftests: mlxsw: vxlan_flooding_ipv6: Prevent flooding of unwanted packets
  selftests: mlxsw: vxlan_flooding: Prevent flooding of unwanted packets
  nfc: MAINTAINERS: add Bug entry
  net: stmmac: Use readl_poll_timeout_atomic() in atomic state
  doc/ip-sysctl: add bc_forwarding
  netlink: reset network and mac headers in netlink_dump()
  net: mscc: ocelot: fix broken IP multicast flooding
  net: dsa: hellcreek: Calculate checksums in tagger
  net: atlantic: invert deep par in pm functions, preventing null derefs
  can: isotp: stop timeout monitoring when no first frame was sent
  bonding: do not discard lowest hash bit for non layer3+4 hashing
  net: lan966x: Make sure to release ptp interrupt
  ipv6: make ip6_rt_gc_expire an atomic_t
  net: Handle l3mdev in ip_tunnel_init_flow
  l3mdev: l3mdev_master_upper_ifindex_by_index_rcu should be using netdev_master_upper_dev_get_rcu
  net/sched: cls_u32: fix possible leak in u32_init_knode()
  net/sched: cls_u32: fix netns refcount changes in u32_change()
  powerpc: Update MAINTAINERS for ibmvnic and VAS
  net: restore alpha order to Ethernet devices in config
  ...

There is a deadlock in rr_close(), which is shown below:

   (Thread 1)                |      (Thread 2)
                             | rr_open()
rr_close()                   |  add_timer()
 spin_lock_irqsave() //(1)   |  (wait a time)
 ...                         | rr_timer()
 del_timer_sync()            |  spin_lock_irqsave() //(2)
 (wait timer to stop)        |  ...

We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.

This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417125519.82618-1-duoming@zju.edu.cnSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Pull xtensa fixes from Max Filippov:

 - fix patching CPU selection in patch_text

 - fix potential deadlock in ISS platform serial driver

 - fix potential register clobbering in coprocessor exception handler

* tag 'xtensa-20220416' of https://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix a7 clobbering in coprocessor context load/store
  arch: xtensa: platforms: Fix deadlock in rs_close()
  xtensa: patch_text: Fixup last cpu should be master

Pull erofs fixes from Gao Xiang:
 "One patch to fix a use-after-free race related to the on-stack
  z_erofs_decompressqueue, which happens very rarely but needs to be
  fixed properly soon.

  The other patch fixes some sysfs Sphinx warnings"

* tag 'erofs-for-5.18-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  Documentation/ABI: sysfs-fs-erofs: Fix Sphinx errors
  erofs: fix use-after-free of on-stack io[]

This reverts commit 5a519c8f.

It turns out that making the pipe almost arbitrarily large has some
rather unexpected downsides.  The kernel test robot reports a kernel
warning that is due to pipe->max_usage now growing to the point where
the iter_file_splice_write() buffer allocation can no longer be
satisfied as a slab allocation, and the

        int nbufs = pipe->max_usage;
        struct bio_vec *array = kcalloc(nbufs, sizeof(struct bio_vec),
                                        GFP_KERNEL);

code sequence there will now always fail as a result.

That code could be modified to use kvcalloc() too, but I feel very
uncomfortable making those kinds of changes for a very niche use case
that really should have other options than make these kinds of
fundamental changes to pipe behavior.

Maybe the CRIU process dumping should be multi-threaded, and use
multiple pipes and multiple cores, rather than try to use one larger
pipe to minimize splice() calls.
Reported-by: kernel test robot <oliver.sang@intel.com>
Link: https://lore.kernel.org/all/20220420073717.GD16310@xsang-OptiPlex-9020/
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The first "if" condition in __memcpy_flushcache is supposed to align the
"dest" variable to 8 bytes and copy data up to this alignment.  However,
this condition may misbehave if "size" is greater than 4GiB.

The statement min_t(unsigned, size, ALIGN(dest, 8) - dest); casts both
arguments to unsigned int and selects the smaller one.  However, the
cast truncates high bits in "size" and it results in misbehavior.

For example:

	suppose that size == 0x100000001, dest == 0x200000002
	min_t(unsigned, size, ALIGN(dest, 8) - dest) == min_t(0x1, 0xe) == 0x1;
	...
	dest += 0x1;

so we copy just one byte "and" dest remains unaligned.

This patch fixes the bug by replacing unsigned with size_t.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The test verifies that packets are correctly flooded by the bridge and
the VXLAN device by matching on the encapsulated packets at the other
end. However, if packets other than those generated by the test also
ingress the bridge (e.g., MLD packets), they will be flooded as well and
interfere with the expected count.

Make the test more robust by making sure that only the packets generated
by the test can ingress the bridge. Drop all the rest using tc filters
on the egress of 'br0' and 'h1'.

In the software data path, the problem can be solved by matching on the
inner destination MAC or dropping unwanted packets at the egress of the
VXLAN device, but this is not currently supported by mlxsw.

Fixes: d01724dd ("selftests: mlxsw: spectrum-2: Add a test for VxLAN flooding with IPv6")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The test verifies that packets are correctly flooded by the bridge and
the VXLAN device by matching on the encapsulated packets at the other
end. However, if packets other than those generated by the test also
ingress the bridge (e.g., MLD packets), they will be flooded as well and
interfere with the expected count.

Make the test more robust by making sure that only the packets generated
by the test can ingress the bridge. Drop all the rest using tc filters
on the egress of 'br0' and 'h1'.

In the software data path, the problem can be solved by matching on the
inner destination MAC or dropping unwanted packets at the egress of the
VXLAN device, but this is not currently supported by mlxsw.

Fixes: 94d302de ("selftests: mlxsw: Add a test for VxLAN flooding")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a Bug section, indicating preferred mailing method for bug reports,
to NFC Subsystem entry.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The init_systime() may be invoked in atomic state. We have observed the
following call trace when running "phc_ctl /dev/ptp0 set" on a Intel
Agilex board.
  BUG: sleeping function called from invalid context at drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:74
  in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 381, name: phc_ctl
  preempt_count: 1, expected: 0
  RCU nest depth: 0, expected: 0
  Preemption disabled at:
  [<ffff80000892ef78>] stmmac_set_time+0x34/0x8c
  CPU: 2 PID: 381 Comm: phc_ctl Not tainted 5.18.0-rc2-next-20220414-yocto-standard+ #567
  Hardware name: SoCFPGA Agilex SoCDK (DT)
  Call trace:
   dump_backtrace.part.0+0xc4/0xd0
   show_stack+0x24/0x40
   dump_stack_lvl+0x7c/0xa0
   dump_stack+0x18/0x34
   __might_resched+0x154/0x1c0
   __might_sleep+0x58/0x90
   init_systime+0x78/0x120
   stmmac_set_time+0x64/0x8c
   ptp_clock_settime+0x60/0x9c
   pc_clock_settime+0x6c/0xc0
   __arm64_sys_clock_settime+0x88/0xf0
   invoke_syscall+0x5c/0x130
   el0_svc_common.constprop.0+0x4c/0x100
   do_el0_svc+0x7c/0xa0
   el0_svc+0x58/0xcc
   el0t_64_sync_handler+0xa4/0x130
   el0t_64_sync+0x18c/0x190

So we should use readl_poll_timeout_atomic() here instead of
readl_poll_timeout().

Also adjust the delay time to 10us to fix a "__bad_udelay" build error
reported by "kernel test robot <lkp@intel.com>". I have tested this on
Intel Agilex and NXP S32G boards, there is no delay needed at all.
So the 10us delay should be long enough for most cases.

Fixes: ff8ed737 ("net: stmmac: use readl_poll_timeout() function in init_systime()")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let's describe this sysctl.

Fixes: 5cbf777c ("route: add support for directed broadcast forwarding")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huge page backed vmalloc memory could benefit performance in many cases.
However, some users of vmalloc may not be ready to handle huge pages for
various reasons: hardware constraints, potential pages split, etc.
VM_NO_HUGE_VMAP was introduced to allow vmalloc users to opt-out huge
pages.  However, it is not easy to track down all the users that require
the opt-out, as the allocation are passed different stacks and may cause
issues in different layers.

To address this issue, replace VM_NO_HUGE_VMAP with an opt-in flag,
VM_ALLOW_HUGE_VMAP, so that users that benefit from huge pages could ask
specificially.

Also, remove vmalloc_no_huge() and add opt-in helper vmalloc_huge().

Fixes: fac54e2b ("x86/Kconfig: Select HAVE_ARCH_HUGE_VMALLOC with HAVE_ARCH_HUGE_VMAP")
Link: https://lore.kernel.org/netdev/14444103-d51b-0fb3-ee63-c3f182f0b546@molgen.mpg.de/"
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <song@kernel.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull spi fixes from Mark Brown:
 "A few more fixes for SPI, plus one new PCI ID for another Intel
  chipset.

  All device specific stuff"

* tag 'spi-fix-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: atmel-quadspi: Fix the buswidth adjustment between spi-mem and controller
  spi: cadence-quadspi: fix incorrect supports_op() return value
  spi: intel: Add support for Raptor Lake-S SPI serial flash
  spi: spi-mtk-nor: initialize spi controller after resume

Last cycle we extended the idmapped mounts infrastructure to support
idmapped mounts of idmapped filesystems (No such filesystem yet exist.).
Since then, the meaning of an idmapped mount is a mount whose idmapping
is different from the filesystems idmapping.

While doing that work we missed to adapt the acl translation helpers.
They still assume that checking for the identity mapping is enough.  But
they need to use the no_idmapping() helper instead.

Note, POSIX ACLs are always translated right at the userspace-kernel
boundary using the caller's current idmapping and the initial idmapping.
The order depends on whether we're coming from or going to userspace.
The filesystem's idmapping doesn't matter at the border.

Consequently, if a non-idmapped mount is passed we need to make sure to
always pass the initial idmapping as the mount's idmapping and not the
filesystem idmapping.  Since it's irrelevant here it would yield invalid
ids and prevent setting acls for filesystems that are mountable in a
userns and support posix acls (tmpfs and fuse).

I verified the regression reported in [1] and verified that this patch
fixes it.  A regression test will be added to xfstests in parallel.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=215849 [1]
Fixes: bd303368 ("fs: support mapped mounts of mapped filesystems")
Cc: Seth Forshee <sforshee@digitalocean.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # 5.17
Cc: <regressions@lists.linux.dev>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

netlink_dump() is allocating an skb, reserves space in it
but forgets to reset network header.

This allows a BPF program, invoked later from sk_filter()
to access uninitialized kernel memory from the reserved
space.

Theorically mac header reset could be omitted, because
it is set to a special initial value.
bpf_internal_load_pointer_neg_helper calls skb_mac_header()
without checking skb_mac_header_was_set().
Relying on skb->len not being too big seems fragile.
We also could add a sanity check in bpf_internal_load_pointer_neg_helper()
to avoid surprises in the future.

syzbot report was:

BUG: KMSAN: uninit-value in ___bpf_prog_run+0xa22b/0xb420 kernel/bpf/core.c:1637
 ___bpf_prog_run+0xa22b/0xb420 kernel/bpf/core.c:1637
 __bpf_prog_run32+0x121/0x180 kernel/bpf/core.c:1796
 bpf_dispatcher_nop_func include/linux/bpf.h:784 [inline]
 __bpf_prog_run include/linux/filter.h:626 [inline]
 bpf_prog_run include/linux/filter.h:633 [inline]
 __bpf_prog_run_save_cb+0x168/0x580 include/linux/filter.h:756
 bpf_prog_run_save_cb include/linux/filter.h:770 [inline]
 sk_filter_trim_cap+0x3bc/0x8c0 net/core/filter.c:150
 sk_filter include/linux/filter.h:905 [inline]
 netlink_dump+0xe0c/0x16c0 net/netlink/af_netlink.c:2276
 netlink_recvmsg+0x1129/0x1c80 net/netlink/af_netlink.c:2002
 sock_recvmsg_nosec net/socket.c:948 [inline]
 sock_recvmsg net/socket.c:966 [inline]
 sock_read_iter+0x5a9/0x630 net/socket.c:1039
 do_iter_readv_writev+0xa7f/0xc70
 do_iter_read+0x52c/0x14c0 fs/read_write.c:786
 vfs_readv fs/read_write.c:906 [inline]
 do_readv+0x432/0x800 fs/read_write.c:943
 __do_sys_readv fs/read_write.c:1034 [inline]
 __se_sys_readv fs/read_write.c:1031 [inline]
 __x64_sys_readv+0xe5/0x120 fs/read_write.c:1031
 do_syscall_x64 arch/x86/entry/common.c:51 [inline]
 do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:81
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Uninit was stored to memory at:
 ___bpf_prog_run+0x96c/0xb420 kernel/bpf/core.c:1558
 __bpf_prog_run32+0x121/0x180 kernel/bpf/core.c:1796
 bpf_dispatcher_nop_func include/linux/bpf.h:784 [inline]
 __bpf_prog_run include/linux/filter.h:626 [inline]
 bpf_prog_run include/linux/filter.h:633 [inline]
 __bpf_prog_run_save_cb+0x168/0x580 include/linux/filter.h:756
 bpf_prog_run_save_cb include/linux/filter.h:770 [inline]
 sk_filter_trim_cap+0x3bc/0x8c0 net/core/filter.c:150
 sk_filter include/linux/filter.h:905 [inline]
 netlink_dump+0xe0c/0x16c0 net/netlink/af_netlink.c:2276
 netlink_recvmsg+0x1129/0x1c80 net/netlink/af_netlink.c:2002
 sock_recvmsg_nosec net/socket.c:948 [inline]
 sock_recvmsg net/socket.c:966 [inline]
 sock_read_iter+0x5a9/0x630 net/socket.c:1039
 do_iter_readv_writev+0xa7f/0xc70
 do_iter_read+0x52c/0x14c0 fs/read_write.c:786
 vfs_readv fs/read_write.c:906 [inline]
 do_readv+0x432/0x800 fs/read_write.c:943
 __do_sys_readv fs/read_write.c:1034 [inline]
 __se_sys_readv fs/read_write.c:1031 [inline]
 __x64_sys_readv+0xe5/0x120 fs/read_write.c:1031
 do_syscall_x64 arch/x86/entry/common.c:51 [inline]
 do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:81
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Uninit was created at:
 slab_post_alloc_hook mm/slab.h:737 [inline]
 slab_alloc_node mm/slub.c:3244 [inline]
 __kmalloc_node_track_caller+0xde3/0x14f0 mm/slub.c:4972
 kmalloc_reserve net/core/skbuff.c:354 [inline]
 __alloc_skb+0x545/0xf90 net/core/skbuff.c:426
 alloc_skb include/linux/skbuff.h:1158 [inline]
 netlink_dump+0x30f/0x16c0 net/netlink/af_netlink.c:2242
 netlink_recvmsg+0x1129/0x1c80 net/netlink/af_netlink.c:2002
 sock_recvmsg_nosec net/socket.c:948 [inline]
 sock_recvmsg net/socket.c:966 [inline]
 sock_read_iter+0x5a9/0x630 net/socket.c:1039
 do_iter_readv_writev+0xa7f/0xc70
 do_iter_read+0x52c/0x14c0 fs/read_write.c:786
 vfs_readv fs/read_write.c:906 [inline]
 do_readv+0x432/0x800 fs/read_write.c:943
 __do_sys_readv fs/read_write.c:1034 [inline]
 __se_sys_readv fs/read_write.c:1031 [inline]
 __x64_sys_readv+0xe5/0x120 fs/read_write.c:1031
 do_syscall_x64 arch/x86/entry/common.c:51 [inline]
 do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:81
 entry_SYSCALL_64_after_hwframe+0x44/0xae

CPU: 0 PID: 3470 Comm: syz-executor751 Not tainted 5.17.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: db65a3aa ("netlink: Trim skb to alloc size to avoid MSG_TRUNC")
Fixes: 9063e21f ("netlink: autosize skb lengthes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220415181442.551228-1-eric.dumazet@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When the user runs:
bridge link set dev $br_port mcast_flood on

this command should affect not only L2 multicast, but also IPv4 and IPv6
multicast.

In the Ocelot switch, unknown multicast gets flooded according to
different PGIDs according to its type, and PGID_MC only handles L2
multicast. Therefore, by leaving PGID_MCIPV4 and PGID_MCIPV6 at their
default value of 0, unknown IP multicast traffic is never flooded.

Fixes: 421741ea ("net: mscc: ocelot: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220415151950.219660-1-vladimir.oltean@nxp.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In case the checksum calculation is offloaded to the DSA master network
interface, it will include the switch trailing tag. As soon as the switch strips
that tag on egress, the calculated checksum is wrong.

Therefore, add the checksum calculation to the tagger (if required) before
adding the switch tag. This way, the hellcreek code works with all DSA master
interfaces regardless of their declared feature set.

Fixes: 01ef09ca ("net: dsa: Add tag handling for Hirschmann Hellcreek switches")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220415103320.90657-1-kurt@linutronix.deSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This will reset deeply on freeze and thaw instead of suspend and
resume and prevent null pointer dereferences of the uninitialized ring
0 buffer while thawing.

The impact is an indefinitely hanging kernel. You can't switch
consoles after this and the only possible user interaction is SysRq.

BUG: kernel NULL pointer dereference
RIP: 0010:aq_ring_rx_fill+0xcf/0x210 [atlantic]
aq_vec_init+0x85/0xe0 [atlantic]
aq_nic_init+0xf7/0x1d0 [atlantic]
atl_resume_common+0x4f/0x100 [atlantic]
pci_pm_thaw+0x42/0xa0

resolves in aq_ring.o to

```
0000000000000ae0 <aq_ring_rx_fill>:
{
/* ... */
 baf:	48 8b 43 08          	mov    0x8(%rbx),%rax
 		buff->flags = 0U; /* buff is NULL */
```

The bug has been present since the introduction of the new pm code in
8aaa112a ("net: atlantic: refactoring pm logic") and was hidden
until 8ce84271 ("net: atlantic: changes for multi-TC support"),
which refactored the aq_vec_{free,alloc} functions into
aq_vec_{,ring}_{free,alloc}, but is technically not wrong. The
original functions just always reinitialized the buffers on S3/S4. If
the interface is down before freezing, the bug does not occur. It does
not matter, whether the initrd contains and loads the module before
thawing.

So the fix is to invert the boolean parameter deep in all pm function
calls, which was clearly intended to be set like that.

First report was on Github [1], which you have to guess from the
resume logs in the posted dmesg snippet. Recently I posted one on
Bugzilla [2], since I did not have an AQC device so far.

#regzbot introduced: 8ce84271
#regzbot from: koo5 <kolman.jindrich@gmail.com>
#regzbot monitor: https://github.com/Aquantia/AQtion/issues/32

Fixes: 8aaa112a ("net: atlantic: refactoring pm logic")
Link: https://github.com/Aquantia/AQtion/issues/32 [1]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215798 [2]
Cc: stable@vger.kernel.org
Reported-by: koo5 <kolman.jindrich@gmail.com>
Signed-off-by: Manuel Ullmann <labre@posteo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.18-20220417' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2022-04-17

this is a pull request of 1 patch for net/master.

The patch is by Oliver Hartkopp and fixes a timeout monitoring problem
in the ISO TP protocol found by the syzbot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull xen fixlet from Juergen Gross:
 "A single cleanup patch for the Xen balloon driver"

* tag 'for-linus-5.18-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: don't use PV mode extra memory for zone device allocations

Pull x86 fixes from Thomas Gleixner:
 "Two x86 fixes related to TSX:

   - Use either MSR_TSX_FORCE_ABORT or MSR_IA32_TSX_CTRL to disable TSX
     to cover all CPUs which allow to disable it.

   - Disable TSX development mode at boot so that a microcode update
     which provides TSX development mode does not suddenly make the
     system vulnerable to TSX Asynchronous Abort"

* tag 'x86-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tsx: Disable TSX development mode at boot
  x86/tsx: Use MSR_TSX_CTRL to clear CPUID bits

Pull timer fixes from Thomas Gleixner:
 "A small set of fixes for the timers core:

   - Fix the warning condition in __run_timers() which does not take
     into account that a CPU base (especially the deferrable base) never
     has a timer armed on it and therefore the next_expiry value can
     become stale.

   - Replace a WARN_ON() in the NOHZ code with a WARN_ON_ONCE() to
     prevent endless spam in dmesg.

   - Remove the double star from a comment which is not meant to be in
     kernel-doc format"

* tag 'timers-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/sched: Fix non-kernel-doc comment
  tick/nohz: Use WARN_ON_ONCE() to prevent console saturation
  timers: Fix warning condition in __run_timers()

Pull SMP fixes from Thomas Gleixner:
 "Two fixes for the SMP core:

   - Make the warning condition in flush_smp_call_function_queue()
     correct, which checked a just emptied list head for being empty
     instead of validating that there was no pending entry on the
     offlined CPU at all.

   - The @cpu member of struct cpuhp_cpu_state is initialized when the
     CPU hotplug thread for the upcoming CPU is created. That's too late
     because the creation of the thread can fail and then the following
     rollback operates on CPU0. Get rid of the CPU member and hand the
     CPU number to the involved functions directly"

* tag 'smp-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Remove the 'cpu' member of cpuhp_cpu_state
  smp: Fix offline cpu check in flush_smp_call_function_queue()

Pull irq fix from Thomas Gleixner:
 "A single fix for the interrupt affinity spreading logic to take into
  account that there can be an imbalance between present and possible
  CPUs, which causes already assigned bits to be overwritten"

* tag 'irq-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/affinity: Consider that CPUs on nodes can be unbalanced

Pull power supply fixes from Sebastian Reichel:

 - Fix a regression with battery data failing to load from DT

* tag 'for-v5.18-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  power: supply: Reset err after not finding static battery
  power: supply: samsung-sdi-battery: Add missing charge restart voltages

Pull i2c fixes from Wolfram Sang:
 "Regular set of fixes for drivers and the dev-interface"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: ismt: Fix undefined behavior due to shift overflowing the constant
  i2c: dev: Force case user pointers in compat_i2cdev_ioctl()
  i2c: dev: check return value when calling dev_set_name()
  i2c: qcom-geni: Use dev_err_probe() for GPI DMA error
  i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit
  i2c: pasemi: Wait for write xfers to finish

The first attempt to fix a the 'impossible' WARN_ON_ONCE(1) in
isotp_tx_timer_handler() focussed on the identical CAN IDs created by
the syzbot reproducer and lead to upstream fix/commit 3ea56642
("can: isotp: sanitize CAN ID checks in isotp_bind()"). But this did
not catch the root cause of the wrong tx.state in the tx_timer handler.

In the isotp 'first frame' case a timeout monitoring needs to be started
before the 'first frame' is send. But when this sending failed the timeout
monitoring for this specific frame has to be disabled too.

Otherwise the tx_timer is fired with the 'warn me' tx.state of ISOTP_IDLE.

Fixes: e057dd3f ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/20220405175112.2682-1-socketcan@hartkopp.net
Reported-by: syzbot+2339c27f5c66c652843e@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Commit b5f86218 was introduced to discard lowest hash bit for layer3+4 hashing
but it also removes last bit from non layer3+4 hashing

Below script shows layer2+3 hashing will result in same slave to be used with above commit.
$ cat hash.py
#/usr/bin/python3.6

h_dests=[0xa0, 0xa1]
h_source=0xe3
hproto=0x8
saddr=0x1e7aa8c0
daddr=0x17aa8c0

for h_dest in h_dests:
    hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
    hash ^= hash >> 16
    hash ^= hash >> 8
    print(hash)

print("with last bit removed")
for h_dest in h_dests:
    hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
    hash ^= hash >> 16
    hash ^= hash >> 8
    hash = hash >> 1
    print(hash)

Output:
$ python3.6 hash.py
522133332
522133333   <-------------- will result in both slaves being used

with last bit removed
261066666
261066666   <-------------- only single slave used
Signed-off-by: suresh kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull devicetree fixes from Rob Herring:

 - Fix scalar property schemas with array constraints

 - Fix 'enum' lists with duplicate entries

 - Fix incomplete if/then/else schemas

 - Add Renesas RZ/V2L SoC support to Mali Bifrost binding

 - Maintainers update for Marvell irqchip

* tag 'devicetree-fixes-for-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: display: panel-timing: Define a single type for properties
  dt-bindings: Fix array constraints on scalar properties
  dt-bindings: gpu: mali-bifrost: Document RZ/V2L SoC
  dt-bindings: net: snps: remove duplicate name
  dt-bindings: Fix 'enum' lists with duplicate entries
  dt-bindings: irqchip: mrvl,intc: refresh maintainers
  dt-bindings: Fix incomplete if/then/else schemas
  dt-bindings: power: renesas,apmu: Fix cpus property limits
  dt-bindings: extcon: maxim,max77843: fix ports type

Pull gpio fixes from Bartosz Golaszewski:
 "A single fix for gpio-sim and two patches for GPIO ACPI pulled from
  Andy:

   - fix the set/get_multiple() callbacks in gpio-sim

   - use correct format characters in gpiolib-acpi

   - use an unsigned type for pins in gpiolib-acpi"

* tag 'gpio-fixes-for-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: sim: fix setting and getting multiple lines
  gpiolib: acpi: Convert type for pin to be unsigned
  gpiolib: acpi: use correct format characters

Pull ARM SoC fixes from Arnd Bergmann:
 "There are a number of SoC bugfixes that came in since the merge
  window, and more of them are already pending.

  This batch includes:

   - A boot time regression fix for davinci that triggered on
     multi_v5_defconfig when booting any platform

   - Defconfig updates to address removed features, changed symbol names
     or dependencies, for gemini, ux500, and pxa

   - Email address changes for Krzysztof Kozlowski

   - Build warning fixes for ep93xx and iop32x

   - Devicetree warning fixes across many platforms

   - Minor bugfixes for the reset controller, memory controller and SCMI
     firmware subsystems plus the versatile-express board"

* tag 'soc-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (34 commits)
  ARM: config: Update Gemini defconfig
  arm64: dts: qcom/sdm845-shift-axolotl: Fix boolean properties with values
  ARM: dts: align SPI NOR node name with dtschema
  ARM: dts: Fix more boolean properties with values
  arm/arm64: dts: qcom: Fix boolean properties with values
  arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
  arm: dts: imx: Fix boolean properties with values
  arm64: dts: tegra: Fix boolean properties with values
  arm: dts: at91: Fix boolean properties with values
  arm: configs: imote2: Drop defconfig as board support dropped.
  ep93xx: clock: Don't use plain integer as NULL pointer
  ep93xx: clock: Fix UAF in ep93xx_clk_register_gate()
  ARM: vexpress/spc: Fix all the kernel-doc build warnings
  ARM: vexpress/spc: Fix kernel-doc build warning for ve_spc_cpu_in_wfi
  ARM: config: u8500: Re-enable AB8500 battery charging
  ARM: config: u8500: Add some common hardware
  memory: fsl_ifc: populate child nodes of buses and mfd devices
  ARM: config: Refresh U8500 defconfig
  firmware: arm_scmi: Fix sparse warnings in OPTEE transport driver
  firmware: arm_scmi: Replace zero-length array with flexible-array member
  ...

Pull random number generator fixes from Jason Donenfeld:

 - Per your suggestion, random reads now won't fail if there's a page
   fault after some non-zero amount of data has been read, which makes
   the behavior consistent with all other reads in the kernel.

 - Rather than an inconsistent mix of random_get_entropy() returning an
   unsigned long or a cycles_t, now it just returns an unsigned long.

 - A memcpy() was replaced with an memmove(), because the addresses are
   sometimes overlapping. In practice the destination is always before
   the source, so not really an issue, but better to be correct than
   not.

* tag 'random-5.18-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
  random: use memmove instead of memcpy for remaining 32 bytes
  random: make random_get_entropy() return an unsigned long
  random: allow partial reads if later user copies fail

Pull SCSI fixes from James Bottomley:
 "13 fixes, all in drivers.

  The most extensive changes are in the iscsi series (affecting drivers
  qedi, cxgbi and bnx2i), the next most is scsi_debug, but that's just a
  simple revert and then minor updates to pm80xx"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: iscsi: MAINTAINERS: Add Mike Christie as co-maintainer
  scsi: qedi: Fix failed disconnect handling
  scsi: iscsi: Fix NOP handling during conn recovery
  scsi: iscsi: Merge suspend fields
  scsi: iscsi: Fix unbound endpoint error handling
  scsi: iscsi: Fix conn cleanup and stop race during iscsid restart
  scsi: iscsi: Fix endpoint reuse regression
  scsi: iscsi: Release endpoint ID when its freed
  scsi: iscsi: Fix offload conn cleanup when iscsid restarts
  scsi: iscsi: Move iscsi_ep_disconnect()
  scsi: pm80xx: Enable upper inbound, outbound queues
  scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63
  Revert "scsi: scsi_debug: Address races following module load"

Merge tag 'intel-gpio-v5.18-2' of gitolite.kernel.org:pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-current

intel-gpio for v5.18-2

* Couple of fixes related to handling unsigned value of the pin from ACPI

gpiolib:
 -  acpi: Convert type for pin to be unsigned
 -  acpi: use correct format characters

Pull dma-mapping fix from Christoph Hellwig:

 - avoid a double memory copy for swiotlb (Chao Gao)

* tag 'dma-mapping-5.18-2' of git://git.infradead.org/users/hch/dma-mapping:
  dma-direct: avoid redundant memory sync for swiotlb

In order to immediately overwrite the old key on the stack, before
servicing a userspace request for bytes, we use the remaining 32 bytes
of block 0 as the key. This means moving indices 8,9,a,b,c,d,e,f ->
4,5,6,7,8,9,a,b. Since 4 < 8, for the kernel implementations of
memcpy(), this doesn't actually appear to be a problem in practice. But
relying on that characteristic seems a bit brittle. So let's change that
to a proper memmove(), which is the by-the-books way of handling
overlapping memory copies.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>

Fast coprocessor exception handler saves a3..a6, but coprocessor context
load/store code uses a4..a7 as temporaries, potentially clobbering a7.
'Potentially' because coprocessor state load/store macros may not use
all four temporary registers (and neither FPU nor HiFi macros do).
Use a3..a6 as intended.

Cc: stable@vger.kernel.org
Fixes: c658eac6 ("[XTENSA] Add support for configurable registers and coprocessors")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>

Merge misc fixes from Andrew Morton:
 "14 patches.

  Subsystems affected by this patch series: MAINTAINERS, binfmt, and
  mm (tmpfs, secretmem, kasan, kfence, pagealloc, zram, compaction,
  hugetlb, vmalloc, and kmemleak)"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: kmemleak: take a full lowmem check in kmemleak_*_phys()
  mm/vmalloc: fix spinning drain_vmap_work after reading from /proc/vmcore
  revert "fs/binfmt_elf: use PT_LOAD p_align values for static PIE"
  revert "fs/binfmt_elf: fix PT_LOAD p_align values for loaders"
  hugetlb: do not demote poisoned hugetlb pages
  mm: compaction: fix compiler warning when CONFIG_COMPACTION=n
  mm: fix unexpected zeroed page mapping with zram swap
  mm, page_alloc: fix build_zonerefs_node()
  mm, kfence: support kmem_dump_obj() for KFENCE objects
  kasan: fix hw tags enablement when KUNIT tests are disabled
  irq_work: use kasan_record_aux_stack_noalloc() record callstack
  mm/secretmem: fix panic when growing a memfd_secret
  tmpfs: fix regressions from wider use of ZERO_PAGE
  MAINTAINERS: Broadcom internal lists aren't maintainers

Merge tag 'for-5.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix memory corruption in DM integrity target when tag_size is less
   than digest size.

 - Fix DM multipath's historical-service-time path selector to not use
   sched_clock() and ktime_get_ns(); only use ktime_get_ns().

 - Fix dm_io->orig_bio NULL pointer dereference in dm_zone_map_bio() due
   to 5.18 changes that overlooked DM zone's use of ->orig_bio

 - Fix for regression that broke the use of dm_accept_partial_bio() for
   "abnormal" IO (e.g. WRITE ZEROES) that does not need duplicate bios

 - Fix DM's issuing of empty flush bio so that it's size is 0.

* tag 'for-5.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix bio length of empty flush
  dm: allow dm_accept_partial_bio() for dm_io without duplicate bios
  dm zone: fix NULL pointer dereference in dm_zone_map_bio
  dm mpath: only use ktime_get_ns() in historical selector
  dm integrity: fix memory corruption when tag_size is less than digest size