A NULL pointer dereference occurs when the driver
is unloaded, and the SDMA rhashtable is freed if
the rhashtable_init() function has not been called.
Prevent this by changing sdma_rht to be a pointer
to a dynamically allocated hash table. The NULL-ness
of the pointer serves as an indication that the hash
table was initialized and that it needs to be
destroyed.

Fixes: 0cb2aa69 ("IB/hfi1: Add sysfs interface for affinity setup")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When the LCB is going offline, inopportune port queries can cause
benign error messages to be logged.  To deal with this, cache the
registers just before setting the LCB to offline, allowing queries to
return without eliciting the error.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Set the errcode before the state and add the smb_wmb() to avoid a
potential race condition with the user.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

If the logical link state does not read as down when
the physical link state is offline, force it to down.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When udev renames the netdev devices, ipoib debugfs entries does not
get renamed. As a result, if subsequent probe of ipoib device reuse the
name then creating a debugfs entry for the new device would fail.

Also, moved ipoib_create_debug_files and ipoib_delete_debug_files as part
of ipoib event handling in order to avoid any race condition between these.

Fixes: 1732b0ef ([IPoIB] add path record information in debugfs)
Cc: stable@vger.kernel.org # 2.6.15+
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

hns_roce_hw_v1.c uses DT interfaces but relies on implict inclusion of
linux/of.h which means that changes in other headers could break the
build, as happened in -next for arm64 today.  Add an explicit include.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This patch adds the standard fd based type - completion_channel.
The completion_channel is now prefixed with ib_uobject, similarly
to the rest of the uobjects.
This requires a few changes:
(1) We define a new completion channel fd based object type.
(2) completion_event and async_event are now two different types.
    This means they use different fops.
(3) We release the completion_channel exactly as we release other
    idr based objects.
(4) Since ib_uobjects are already kref-ed, we only add the kref to the
    async event.

A fd object requires filling out several parameters. Its op pointer
should point to uverbs_fd_ops and its size should be at least the
size if ib_uobject. We use a macro to make the type declaration
easier.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The completion channel we use in verbs infrastructure is FD based.
Previously, we had a separate way to manage this object. Since we
strive for a single way to manage any kind of object in this
infrastructure, we conceptually treat all objects as subclasses
of ib_uobject.

This commit adds the necessary mechanism to support FD based objects
like their IDR counterparts. FD objects release need to be synchronized
with context release. We use the cleanup_mutex on the uverbs_file for
that.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When two handlers used the same object in the old schema, we blocked
the process in the kernel. The new schema just returns -EBUSY. This
could lead to different behaviour in applications between the old
schema and the new schema. In most cases, using such handlers
concurrently could lead to crashing the process. For example, if
thread A destroys a QP and thread B modifies it, we could have the
destruction happens before the modification. In this case, we are
accessing freed memory which could lead to crashing the process.
This is true for most cases. However, attaching and detaching
a multicast address from QP concurrently is safe. Therefore, we
preserve the original behaviour by adding a lock there.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This changes only the handlers which deals with idr based objects to
use the new idr allocation, fetching and destruction schema.
This patch consists of the following changes:
(1) Allocation, fetching and destruction is done via idr ops.
(2) Context initializing and release is done through
    uverbs_initialize_ucontext and uverbs_cleanup_ucontext.
(3) Ditching the live flag. Mostly, this is pretty straight
    forward. The only place that is a bit trickier is in
    ib_uverbs_open_qp. Commit [1] added code to check whether
    the uobject is already live and initialized. This mostly
    happens because of a race between open_qp and events.
    We delayed assigning the uobject's pointer in order to
    eliminate this race without using the live variable.

[1] commit a040f95d
	("IB/core: Fix XRC race condition in ib_uverbs_open_qp")
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This patch adds the standard idr based types. These types are
used in downstream patches in order to initialize, destroy and
lookup IB standard objects which are based on idr objects.

An idr object requires filling out several parameters. Its op pointer
should point to uverbs_idr_ops and its size should be at least the
size of ib_uobject. We add a macro to make the type declaration easier.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The new ioctl infrastructure supports driver specific objects.
Each such object type has a hot unplug function, allocation size and
an order of destruction.

When a ucontext is created, a new list is created in this ib_ucontext.
This list contains all objects created under this ib_ucontext.
When a ib_ucontext is destroyed, we traverse this list several time
destroying the various objects by the order mentioned in the object
type description. If few object types have the same destruction order,
they are destroyed in an order opposite to their creation.

Adding an object is done in two parts.
First, an object is allocated and added to idr tree. Then, the
command's handlers (in downstream patches) could work on this object
and fill in its required details.
After a successful command, the commit part is called and the user
objects become ucontext visible. If the handler failed, alloc_abort
should be called.

Removing an uboject is done by calling lookup_get with the write flag
and finalizing it with destroy_commit. A major change from the previous
code is that we actually destroy the kernel object itself in
destroy_commit (rather than just the uobject).

We should make sure idr (per-uverbs-file) and list (per-ucontext) could
be accessed concurrently without corrupting them.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The current code creates an idr per type. Since types are currently
common for all drivers and known in advance, this was good enough.
However, the proposed ioctl based infrastructure allows each driver
to declare only some of the common types and declare its own specific
types.

Thus, we decided to implement idr to be per uverbs_file.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check.  The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.

I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there.  I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.

Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more powerpc fixes from Michael Ellerman:
 "A couple of minor powerpc fixes for 4.11:

   - wire up statx() syscall

   - don't print a warning on memory hotplug when HPT resizing isn't
     available

  Thanks to: David Gibson, Chandan Rajendra"

* tag 'powerpc-4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: Don't give a warning when HPT resizing isn't available
  powerpc: Wire up statx() syscall

Pull parisc fixes from Helge Deller:

 - Mikulas Patocka added support for R_PARISC_SECREL32 relocations in
   modules with CONFIG_MODVERSIONS.

 - Dave Anglin optimized the cache flushing for vmap ranges.

 - Arvind Yadav provided a fix for a potential NULL pointer dereference
   in the parisc perf code (and some code cleanups).

 - I wired up the new statx system call, fixed some compiler warnings
   with the access_ok() macro and fixed shutdown code to really halt a
   system at shutdown instead of crashing & rebooting.

* 'parisc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix system shutdown halt
  parisc: perf: Fix potential NULL pointer dereference
  parisc: Avoid compiler warnings with access_ok()
  parisc: Wire up statx system call
  parisc: Optimize flush_kernel_vmap_range and invalidate_kernel_vmap_range
  parisc: support R_PARISC_SECREL32 relocation in modules

Pull SCSI target fixes from Nicholas Bellinger:
 "The bulk of the changes are in qla2xxx target driver code to address
  various issues found during Cavium/QLogic's internal testing (stable
  CC's included), along with a few other stability and smaller
  miscellaneous improvements.

  There are also a couple of different patch sets from Mike Christie,
  which have been a result of his work to use target-core ALUA logic
  together with tcm-user backend driver.

  Finally, a patch to address some long standing issues with
  pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
  which will make folks using physical (or virtual) magnetic tape happy"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
  qla2xxx: Update driver version to 9.00.00.00-k
  qla2xxx: Fix delayed response to command for loop mode/direct connect.
  qla2xxx: Change scsi host lookup method.
  qla2xxx: Add DebugFS node to display Port Database
  qla2xxx: Use IOCB interface to submit non-critical MBX.
  qla2xxx: Add async new target notification
  qla2xxx: Export DIF stats via debugfs
  qla2xxx: Improve T10-DIF/PI handling in driver.
  qla2xxx: Allow relogin to proceed if remote login did not finish
  qla2xxx: Fix sess_lock & hardware_lock lock order problem.
  qla2xxx: Fix inadequate lock protection for ABTS.
  qla2xxx: Fix request queue corruption.
  qla2xxx: Fix memory leak for abts processing
  qla2xxx: Allow vref count to timeout on vport delete.
  tcmu: Convert cmd_time_out into backend device attribute
  tcmu: make cmd timeout configurable
  tcmu: add helper to check if dev was configured
  target: fix race during implicit transition work flushes
  target: allow userspace to set state to transitioning
  target: fix ALUA transition timeout handling
  ...

Pull device-dax fixes from Dan Williams:
 "The device-dax driver was not being careful to handle falling back to
  smaller fault-granularity sizes.

  The driver already fails fault attempts that are smaller than the
  device's alignment, but it also needs to handle the cases where a
  larger page mapping could be established. For simplicity of the
  immediate fix the implementation just signals VM_FAULT_FALLBACK until
  fault-size == device-alignment.

  One fix is for -stable to address pmd-to-pte fallback from the
  original implementation, another fix is for the new (introduced in
  4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
  ride.

  These have received a build success notification from the kbuild
  robot"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: fix debug output typo
  device-dax: fix pud fault fallback handling
  device-dax: fix pmd/pte fault fallback handling

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.

Following commands are being routed through IOCB interface

- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Add routines to support T10 DIF tag.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.

Use hardware_lock only for error response in this case.

Path1
       CPU0                    CPU1
       ----                    ----
  lock(&(&ha->tgt.sess_lock)->rlock);
                               lock(&(&ha->hardware_lock)->rlock);
                               lock(&(&ha->tgt.sess_lock)->rlock);
  lock(&(&ha->hardware_lock)->rlock);

Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0

Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Instead of putting cmd_time_out under ../target/core/user_0/foo/control,
which has historically been used by parameters needed for initial
backend device configuration, go ahead and move cmd_time_out into
a backend device attribute.

In order to do this, tcmu_module_init() has been updated to create
a local struct configfs_attribute **tcmu_attrs, that is based upon
the existing passthrough_attrib_attrs along with the new cmd_time_out
attribute.  Once **tcm_attrs has been setup, go ahead and point
it at tcmu_ops->tb_dev_attrib_attrs so it's picked up by target-core.

Also following MNC's previous change, ->cmd_time_out is stored in
milliseconds but exposed via configfs in seconds.  Also, note this
patch restricts the modification of ->cmd_time_out to before +
after the TCMU device has been configured, but not while it has
active fabric exports.

Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

A single daemon could implement multiple types of devices
using multuple types of real devices that may not support
restarting from crashes and/or handling tcmu timeouts. This
makes the cmd timeout configurable, so handlers that do not
support it can turn if off for now.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This adds a helper to check if the dev was configured. It
will be used in the next patch to prevent updates to some
config settings after the device has been setup.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Pull OpenRISC fixes from Stafford Horne:
 "OpenRISC fixes for build issues that were exposed by kbuild robots
  after 4.11 merge. All from allmodconfig builds. This includes:

   - bug in the handling of 8-byte get_user() calls

   - module build failure due to multile missing symbol exports"

* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
  openrisc: Export symbols needed by modules
  openrisc: fix issue handling 8 byte get_user calls
  openrisc: xchg: fix `computed is not used` warning

This fixes the following races:

1. core_alua_do_transition_tg_pt could have read
tg_pt_gp_alua_access_state and gone into this if chunk:

if (!explicit &&
        atomic_read(&tg_pt_gp->tg_pt_gp_alua_access_state) ==
           ALUA_ACCESS_STATE_TRANSITION) {

and then core_alua_do_transition_tg_pt_work could update the
state. core_alua_do_transition_tg_pt would then only set
tg_pt_gp_alua_pending_state and the tg_pt_gp_alua_access_state would
not get updated with the second calls state.

2. core_alua_do_transition_tg_pt could be setting
tg_pt_gp_transition_complete while the tg_pt_gp_transition_work
is already completing. core_alua_do_transition_tg_pt then waits on the
completion that will never be called.

To handle these issues, we just call flush_work which will return when
core_alua_do_transition_tg_pt_work has completed so there is no need
to do the complete/wait. And, if core_alua_do_transition_tg_pt_work
was running, instead of trying to sneak in the state change, we just
schedule up another core_alua_do_transition_tg_pt_work call.

Note that this does not handle a possible race where there are multiple
threads call core_alua_do_transition_tg_pt at the same time. I think
we need a mutex in target_tg_pt_gp_alua_access_state_store.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Userspace target_core_user handlers like tcmu-runner may want to set the
ALUA state to transitioning while it does implicit transitions. This
patch allows that state when set from configfs.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The implicit transition time tells initiators the min time
to wait before timing out a transition. We currently schedule
the transition to occur in tg_pt_gp_implicit_trans_secs
seconds so there is no room for delays. If
core_alua_do_transition_tg_pt_work->core_alua_update_tpg_primary_metadata
needs to write out info to a remote file, then the initiator can
easily time out the operation.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>