The reserved implicit-NULL label isn't allowed to appear in the label
stack for packets, so make it an error for the control plane to
specify it as an outgoing label.
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An MPLS network is a single trust domain where the edges must be in
control of what labels make their way into the core. The simplest way
of ensuring this is for the edge device to always impose the labels,
and not allow forward labeled traffic from untrusted neighbours. This
is achieved by allowing a per-device configuration of whether MPLS
traffic input from that interface should be processed or not.

To be secure by default, the default state is changed to MPLS being
disabled on all interfaces unless explicitly enabled and no global
option is provided to change the default. Whilst this differs from
other protocols (e.g. IPv6), network operators are used to explicitly
enabling MPLS forwarding on interfaces, and with the number of links
to the MPLS core typically fairly low this doesn't present too much of
a burden on operators.

Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add per-device MPLS state to supported interfaces. Use the presence of
this state in mpls_route_add to determine that this is a supported
interface.

Use the presence of mpls_dev to drop packets that arrived on an
unsupported interface - previously they were allowed through.

Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some feature changes, driver employes an inner-reload flow where it
resets the function and re-configures it with the new required set of
parameters.

Such a flow proves fatal to any VF since those were not intended to be used
while HW is being reset underneath, causing them [at best] to lose all
connectivity.

This changes driver behavior to fail all configuration changes [e.g., mtu
change] requested of the driver in case VFs are active.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thomas Graf says:

====================
rhashtable rehashing fixes

Some rhashtable rehashing bugs found while testing with the
next rhashtable self-test queued up for the next devel cycle:

https://github.com/tgraf/net-next/commits/rht

v2:
 - Moved schedule_work() call into rhashtable_insert_rehash()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code currently only stops inserting rehashes into the
chain when no resizes are currently scheduled. As long as resizes
are scheduled and while inserting above the utilization watermark,
more and more rehashes will be scheduled.

This lead to a perfect DoS storm with thousands of rehashes
scheduled which lead to thousands of spinlocks to be taken
sequentially.

Instead, only allow either a series of resizes or a single rehash.
Drop any further rehashes and return -EBUSY.

Fixes: ccd57b1b ("rhashtable: Add immediate rehash during insertion")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When rhashtable_insert_rehash() fails with ENOMEM, this indicates that
we can't allocate the necessary memory in the current context but the
limits as set by the user would still allow to grow.

Thus attempt an async resize in the background where we can allocate
using GFP_KERNEL which is more likely to succeed. The insertion itself
will still fail to indicate pressure.

This fixes a bug where the table would never continue growing once the
utilization is above 100%.

Fixes: ccd57b1b ("rhashtable: Add immediate rehash during insertion")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using sk_stream_alloc_skb() in tcp_send_fin() is dangerous in
case a huge process is killed by OOM, and tcp_mem[2] is hit.

To be able to free memory we need to make progress, so this
patch allows FIN packets to not care about tcp_mem[2], if
skb allocation succeeded.

In a follow-up patch, we might abort tcp_send_fin() infinite loop
in case TIF_MEMDIE is set on this thread, as memory allocator
did its best getting extra memory already.

This patch reverts d22e1537 ("tcp: fix tcp fin memory accounting")

Fixes: d22e1537 ("tcp: fix tcp fin memory accounting")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MMC fixes from Ulf Hansson:
 "Here is two mmc core fixes for v.4.1 rc1:

   - fix error code propagation in mmc_pwrseq_simple_alloc()

   - revert 'mmc: core: Convert mmc_driver to device_driver'"

* tag 'mmc-4.1-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
  Revert "mmc: core: Convert mmc_driver to device_driver"
  mmc: pwrseq: Fix error code propagation in mmc_pwrseq_simple_alloc()

HSU_DMA is selected by the HSU_DMA_PCI driver, this should be user selected
so remove the user prompt for this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC late changes from Olof Johansson:
 "We were expecting to sit on this branch through most of the merge
  window since the contents was merged into our tree late, but we ended
  up sitting on all of our contents so it can go in with the rest.

  The contents here is:

   - a large branch of cleanups of the CM/PRM blocks on OMAP.

   - a couple of patches plumbing up CM/PRM on OMAP5 and DRA7.

   - a branch with DT updates for Freescale i.MX.  including some
     shuffling from .dts to .dtsi (include) files that causes a little
     churn"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
  ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
  ARM: OMAP4+: control: add support for initializing control module via DT
  ARM: dts: dra7: add minimal l4 bus layout with control module support
  ARM: dts: omap5: add minimal l4 bus layout with control module support
  ARM: OMAP4+: control: remove support for legacy pad read/write
  ARM: OMAP4: display: convert display to use syscon for dsi muxing
  ARM: dts: omap4: add minimal l4 bus layout with control module support
  ARM: dts: am4372: add minimal l4 bus layout with control module support
  ARM: dts: am43xx-epos-evm: fix pinmux node layout
  ARM: dts: am33xx: add minimal l4 bus layout with control module support
  ARM: dts: omap3: add minimal l4 bus layout with control module support
  ARM: dts: omap24xx: add minimal l4 bus layout with control module support
  ARM: OMAP2+: control: add syscon support for register accesses
  ARM: OMAP2+: id: cache omap_type value
  ARM: OMAP2+: control: remove API for getting control module base address
  ARM: OMAP2+: clock: add low-level support for regmap
  ARM: OMAP4+: PRM: get rid of cpu_is_omap44xx calls from interrupt init
  ARM: OMAP4+: PRM: setup prm_features from the PRM init time flags
  ARM: OMAP2+: CM: move SoC specific init calls within a generic API
  ARM: OMAP4+: PRM: determine prm_device_inst based on DT compatibility
  ...

Pull ARM SoC 64-bit changes from Olof Johansson:
 "Mostly DT updates for arm64, but also a couple of Kconfig additions.

  Main contents:

   - Qualcomm MSM8916/APQ8016

   - Spreadtrum SC9836

   - Xilinx ZynqMP

   - pincontrol entries for MediaTek MT8173"

* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: add interrupt-affinity property to pmu node for juno
  arm64: dts: Add Qualcomm APQ8016 SBC evaluation board dts
  arm64: dts: Add Qualcomm MSM8916 SoC and evaluation board dts
  arm64: dts: sprd: adding coresight entries to Spreadtrum SC9836
  arm64: Add support for Spreadtrum's Sharkl64 Platform in Kconfig and defconfig
  arm64: dts: Add support for Spreadtrum SC9836 SoC in dts and Makefile
  ARM64: Add new Xilinx ZynqMP SoC
  arm64: qcom: Add support for Qualcomm MSM8916 SoC
  arm64: dts: mt8173: Add pinctrl/GPIO/EINT node for mt8173.
  arm64: mediatek: Select PINCTRL for Mediatek platform

Pull ARM SoC defconfig updates from Olof Johansson:
 "We keep collecting defconfig updates in a separate branch mostly to
  encourage people to handle them separately and avoid conflicts between
  different topics.

  Most of these are enablement of new drivers that have come in, or
  minor config refreshes due to reorderings in Kconfig files, etc.  I.e.
  mostly minor churn of various kinds.

  We might start folding this branch into something else for upstream
  merge since it's so small, but keep it independent in our own tree for
  the above reasons"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
  ARM: multi_v7_defconfig: enable alpine platform
  ARM: multi_v7_defconfig: Add gpio-restart driver
  ARM: multi_v7_defconfig: Build the Marvell WiFi-Ex driver as a module
  ARM: multi_v7_defconfig: Enable support for ELAN i2c trackpads
  ARM: multi_v7_defconfig: Enable Tegra ACTMON support
  ARM: configs: remove all CONFIG_RCAR_AUDMAC_PP from ARM defconfigs
  ARM: configs: enable Marvell Armada 39x in multi_v7_defconfig
  ARM: exynos_defconfig: Enable HDMI support
  ARM: exynos_defconfig: Enable options to mount a rootfs via NFS
  ARM: qcom: Increase MMC_BLOCK_MINORS in defconfig
  ARM: mvebu: Enable perf support in mvebu_v7_defconfig
  ARM: exynos_defconfig: Enable ChromeOS EC chardev driver
  ARM: exynos_defconfig: Enable CPU idle
  ARM: exynos_defconfig: Enable Marvell WiFi-Ex support
  arm: qcom: Update defconfig
  arm: qcom: Enable lpass clock driver in defconfig
  ARM: omap2plus_defconfig: Enable n900 modem as loadable modules
  ARM: omap2plus_defconfig: Update bluetooth options
  ARM: omap2plus_defconfig: Enable leds-pwm
  ARM: omap1_defconfig: drop obsolete Kconfig symbols
  ...

Pull ARM SoC multiplatform code changes from Olof Johansson:
 "The changes here belong to two main platforms:

   - Atmel At91 is flipping the bit and going multiplatform.  This
     includes some cleanups and removal of code, and the final flip of
     config dependencies

   - Shmobile has several platforms that are going multiplatform, but
     this branch also contains a bunch of cleanups that they weren't
     able to keep separate in a good way.  THere's also a removal of one
     of their SoCs and the corresponding boards (sh7372 and mackerel)"

* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
  ARM: at91/pm: move AT91_MEMCTRL_* to pm.h
  ARM: at91/pm: move the standby functions to pm.c
  ARM: at91: fix pm_suspend.S compilation when ARMv6 is selected
  ARM: at91: add a Kconfig dependency on multi-platform
  ARM: at91: drop AT91_TIMER_HZ
  ARM: at91: remove hardware.h
  ARM: at91: remove SoC headers
  ARM: at91: remove useless mach/cpu.h
  ARM: at91: remove unused headers
  ARM: at91: switch at91_dt_defconfig to multiplatform
  ARM: at91: switch to multiplatform
  ARM: shmobile: r8a7778: enable multiplatform target
  ARM: shmobile: bockw: add sound to DT
  ARM: shmobile: r8a7778: add sound to DT
  ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
  DT: i2c: add trivial binding for OKI ML86V7667 video decoder
  ARM: shmobile: r8a7778: common clock framework CPG driver
  ARM: shmobile: bockw dts: set extal clock frequency
  ARM: shmobile: bockw dts: Move Ethernet node to BSC
  ARM: shmobile: r8a73a4: Remove legacy code
  ...

Pull ARM SoC driver updates from Olof Johansson:
 "Driver updates for v4.1.  Some of these are for drivers/soc, where we
  find more and more SoC-specific drivers these days.  Some are for
  other driver subsystems where we have received acks from the
  appropriate maintainers.

  The larger parts of this branch are:

   - MediaTek support for their PMIC wrapper interface, a high-level
     interface for talking to the system PMIC over a dedicated I2C
     interface.

   - Qualcomm SCM driver has been moved to drivers/firmware.  It's used
     for CPU up/down and needs to be in a shared location for arm/arm64
     common code.

   - cleanup of ARM-CCI PMU code.

   - another set of cleanusp to the OMAP GPMC code"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
  soc/mediatek: Remove unused variables
  clocksource: atmel-st: select MFD_SYSCON
  soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs
  arm-cci: Fix CCI PMU event validation
  arm-cci: Split the code for PMU vs driver support
  arm-cci: Get rid of secure transactions for PMU driver
  arm-cci: Abstract the CCI400 PMU specific definitions
  arm-cci: Rearrange code for splitting PMU vs driver code
  drivers: cci: reject groups spanning multiple HW PMUs
  ARM: at91: remove useless include
  clocksource: atmel-st: remove mach/hardware dependency
  clocksource: atmel-st: use syscon/regmap
  ARM: at91: time: move the system timer driver to drivers/clocksource
  ARM: at91: properly initialize timer
  ARM: at91: at91rm9200: remove deprecated arm_pm_restart
  watchdog: at91rm9200: implement restart handler
  watchdog: at91rm9200: use the system timer syscon
  mfd: syscon: Add atmel system timer registers definition
  ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
  soc: qcom: gsbi: Add support for ADM CRCI muxing
  ...

Pull ARM DT updates from Olof Johansson:
 "As always, this tends to be one of our bigger branches.  There are
  lots of updates this release, but not that many jumps out as something
  that needs more detailed coverage.  Some of the highlights are:

   - DTs for the new Annapurna Labs Alpine platform

   - more graphics DT pieces falling into place on Exynos, bridges,
     clocks.

   - plenty of DT updates for Qualcomm platforms for various IP blocks

   - some churn on Tegra due to switch-over to tool-generated pinctrl
     data

   - misc fixes and updates for Atmel at91 platforms

   - various DT updates to add IP block support on Broadcom's Cygnus
     platforms

   - more updates for Renesas platforms as DT support is added for
     various IP blocks (IPMMU, display, audio, etc)"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
  ARM: dts: alpine: add internal pci
  Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
  ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
  ARM: dts: qcom: Add idle state device nodes for 8064
  ARM: dts: qcom: Add idle states device nodes for 8084
  ARM: dts: qcom: Add idle states device nodes for 8974/8074
  ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
  ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
  ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
  devicetree: bindings: Document qcom,idle-states
  devicetree: bindings: Update qcom,saw2 node bindings
  dt-bindings: Add #defines for MSM8916 clocks and resets
  arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
  arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
  arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
  arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
  arm: dts: qcom: Add LCC nodes
  arm: dts: qcom: Add TCSR support for MSM8960
  arm: dts: qcom: Add TCSR support for MSM8660
  arm: dts: qcom: Add TCSR support for IPQ8064
  ...

Pull ARM SoC platform updates from Olof Johansson:
 "Our SoC branch usually contains expanded support for new SoCs and
  other core platform code.  In this case, that includes:

   - support for the new Annapurna Labs "Alpine" platform

   - a rework greatly simplifying adding new platform support to the
     MCPM subsystem (Multi-cluster power management)

   - cpuidle and PM improvements for Exynos3250

   - misc updates for Renesas, OMAP, Meson, i.MX.  Some of these could
     have gone in other branches but ended up here for various reasons"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
  ARM: alpine: add support for generic pci
  ARM: Exynos: migrate DCSCB to the new MCPM backend abstraction
  ARM: vexpress: migrate DCSCB to the new MCPM backend abstraction
  ARM: vexpress: DCSCB: tighten CPU validity assertion
  ARM: vexpress: migrate TC2 to the new MCPM backend abstraction
  ARM: MCPM: move the algorithmic complexity to the core code
  ARM: EXYNOS: allow cpuidle driver usage on Exynos3250 SoC
  ARM: EXYNOS: add AFTR mode support for Exynos3250
  ARM: EXYNOS: add code for setting/clearing boot flag
  ARM: EXYNOS: fix CPU1 hotplug on Exynos3250
  ARM: S3C64XX: Use fixed IRQ bases to avoid conflicts on Cragganmore
  ARM: cygnus: fix const declaration bcm_cygnus_dt_compat
  ARM: DRA7: hwmod: Fix the hwmod class for GPTimer4
  ARM: DRA7: hwmod: Add data for GPTimers 13 through 16
  ARM: EXYNOS: Remove left over 'extra_save'
  ARM: EXYNOS: Constify exynos_pm_data array
  ARM: EXYNOS: use static in suspend.c
  ARM: EXYNOS: Use platform device name as power domain name
  ARM: EXYNOS: add support for async-bridge clocks for pm_domains
  ARM: omap-device: add missed callback for suspend-to-disk
  ...

Pull ARM SoC cleanups from Olof Johansson:
 "We've got a fairly large cleanup branch this time.  The bulk of this
  is removal of non-DT platforms of several flavors:

   - Atmel at91 platforms go full-DT, with removal of remaining
     board-file based support

   - OMAP removes legacy board files for three more platforms

   - removal of non-DT mach-msm, newer Qualcomm platforms now live in
     mach-qcom

   - Freescale i.MX25 also removes non-DT platform support"

Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
  mmc: Remove msm_sdcc driver
  gpio: Remove gpio-msm-v1 driver
  ARM: Remove mach-msm and associated ARM architecture code
  ARM: shmobile: cpuidle: Remove the pointless default driver
  ARM: davinci: dm646x: Add interrupt resource for McASPs
  ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
  ARM: davinci: dm646x: Clean up the McASP DMA resources
  ARM: davinci: devices-da8xx: Add support for McASP2 on da830
  ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
  ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
  ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
  ARM: OMAP2+: Remove legacy support for omap3 TouchBook
  ARM: OMAP3: Remove legacy support for devkit8000
  ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
  ARM: shmobile: Consolidate the pm code for R-Car Gen2
  ARM: shmobile: r8a7791: Correct SYSCIER value
  ARM: shmobile: r8a7790: Correct SYSCIER value
  ARM: at91: remove old setup
  ARM: at91: sama5d4: remove useless map_io
  ARM: at91: sama5 use SoC detection infrastructure
  ...

Pull ARM SoC fixes from Olof Johansson:
 "Here's the usual "low-priority fixes that didn't make it into the last
  few -rcs, with a twist: We had a fixes pull request that I didn't send
  in time to get into 4.0, so we'll send some of them to Greg for
  -stable as well.

  Contents here is as usual not all that controversial:

   - a handful of randconfig fixes from Arnd, in particular for older
     Samsung platforms

   - Exynos fixes, !SMP building, DTS updates for MMC and lid switch

   - Kbuild fix to create output subdirectory for DTB files

   - misc minor fixes for OMAP"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  ARM: at91/dt: sama5d3 xplained: add phy address for macb1
  kbuild: Create directory for target DTB
  ARM: mvebu: Disable CPU Idle on Armada 38x
  ARM: DRA7: Enable Cortex A15 errata 798181
  ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
  ARM: dts: DRA7: Add bandgap and related thermal nodes
  bus: ocp2scp: SYNC2 value should be changed to 0x6
  ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
  ARM: OMAP2+: remove superfluous NULL pointer check
  ARM: EXYNOS: Fix build breakage cpuidle on !SMP
  ARM: dts: fix lid and power pin-functions for exynos5250-spring
  ARM: dts: fix mmc node updates for exynos5250-spring
  ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
  MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
  ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
  ARM: cns3xxx: don't export static symbol
  ARM: S3C24XX: avoid a Kconfig warning
  ARM: S3C24XX: fix header file inclusions
  ARM: S3C24XX: fix building without PM_SLEEP
  ARM: S3C24XX: use SAMSUNG_WAKEMASK for s3c2416
  ...

Pull sparc fixes from David Miller:

 1) ldc_alloc_exp_dring() can be called from softints, so use
    GFP_ATOMIC.  From Sowmini Varadhan.

 2) Some minor warning/build fixups for the new iommu-common code on
    certain archs and with certain debug options enabled.  Also from
    Sowmini Varadhan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Use GFP_ATOMIC in ldc_alloc_exp_dring() as it can be called in softirq context
  sparc64: Use M7 PMC write on all chips T4 and onward.
  iommu-common: rename iommu_pool_hash to iommu_hash_common
  iommu-common: fix x86_64 compiler warnings

Pull networking fixes from David Miller:
 "Just a few fixes trickling in at this point.

  1) If we see an attached socket on an skb in the ipv4 forwarding path,
     bail.  This can happen due to races with FIB rule addition, and
     deletion, and we should just drop such frames.  From Sebastian
     Pöhn.

  2) pppoe receive should only accept packets destined for this hosts's
     MAC address.  From Joakim Tjernlund.

  3) Handle checksum unwrapping properly in ppp receive properly when
     it's encapsulated in UDP in some way, fix from Tom Herbert.

  4) Fix some bugs in mv88e6xxx DSA driver resulting from the conversion
     from register offset constants to mnenomic macros.  From Vivien
     Didelot.

  5) Fix handling of HCA max message size in mlx4 adapters, from Eran
     Ben ELisha"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net/mlx4_core: Fix reading HCA max message size in mlx4_QUERY_DEV_CAP
  tcp: add memory barriers to write space paths
  altera tse: Error-Bit on tx-avalon-stream always set.
  net: dsa: mv88e6xxx: use PORT_DEFAULT_VLAN
  net: dsa: mv88e6xxx: fix setup of port control 1
  ppp: call skb_checksum_complete_unset in ppp_receive_frame
  net: add skb_checksum_complete_unset
  pppoe: Lacks DST MAC address check
  ip_forward: Drop frames with attached skb->sk

Merge tag 'omap-for-v4.1/prcm-dts-mfd-syscon-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/late

Merge "urgent omap boot fix for v4.1 if MFD_SYSCON is not set" from Tony
Lindgren:

Urgent pull request for v4.1 to booting for custom kernel
.config files that do not have MFD_SYSCON set.

Omaps now have a dependency to MFD_SYSCON for system control
module generic register area and some clocks with the changes
done in omap-for-v4.1/prcm-dts branch.

This can be pulled on top of omap-for-v4.1/prcm-dts, or into
fixes for v4.1.

We already do have a slight MFD_SYSCON dependency for
REGULATOR_PBIAS for dual voltage MMC cards on the first MMC
bus for many devices, so from that point of view this can
also be merged separately from omap-for-v4.1/prcm-dts.

* tag 'omap-for-v4.1/prcm-dts-mfd-syscon-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull parisc fixes from Helge Deller:
 "The patch by Guenter Roeck fixes the build on parisc which got broken
  because of commit f24ffde4 ("parisc: expose number of page table
  levels on Kconfig level") and the patch from Matthew Wilcox converts
  our code to use the generic scatterlist.h header file"

* 'parisc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Replace PT_NLEVELS with CONFIG_PGTABLE_LEVELS
  parisc: Eliminate sg_virt_addr() and private scatterlist.h

Currently we parse max_msg_sz from the wrong offset in QUERY_DEV_CAP,
fix to use the right offset.

Fixes: 0b131561 ('net/mlx4_en: Add Flow control statistics [..]')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since it is possible for vnet_event_napi to end up doing
vnet_control_pkt_engine -> ... -> vnet_send_attr ->
vnet_port_alloc_tx_ring -> ldc_alloc_exp_dring -> kzalloc()
(i.e., in softirq context), kzalloc() should be called with
GFP_ATOMIC from ldc_alloc_exp_dring.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

They both work equally well, and the M7 implementation is
simpler and cheaper (less register writes).

With help from David Ahern.
Signed-off-by: David S. Miller <davem@davemloft.net>

The following warning is seen when compiling parisc images

./arch/parisc/include/asm/pgalloc.h: In function 'pgd_alloc':
./arch/parisc/include/asm/pgalloc.h:29:5: warning: "PT_NLEVELS" is not defined

Some definitions of PT_NLEVELS were missed with the conversion to
CONFIG_PGTABLE_LEVELS.

Fixes: f24ffde4 ("parisc: expose number of page table levels
	on Kconfig level")
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>

The only reason to keep parisc's private asm/scatterlist.h was that it
had the macro sg_virt_addr().  Convert all callers to use something else
(sometimes just sg->offset was enough, others should use sg_virt()), and
we can just use the asm-generic scatterlist.h instead.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Dave Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>

Ensure that we either see that the buffer has write space
in tcp_poll() or that we perform a wakeup from the input
side. Did not run into any actual problem here, but thought
that we should make things explicit.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more input subsystem updates from Dmitry Torokhov:

 - an update to Atmel MXT driver that makes it functional on Google
   Pixel 2 boxes (both touchpad and touchscreen)

 - a new VMware VMMouse driver that should allow us drop X vmmouse
   driver that requires root privileges (since it accesses ioports)

 - XBox One controllers now support force feedback (rumble)

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: lm8333 - fix broken email address
  Input: cyapa - fix setting suspend scan rate
  Input: elan_i2c - fix calculating number of x and y traces.
  Input: elan_i2c - report hovering contacts
  Input: elants_i2c - zero-extend hardware ID in firmware name
  Input: alps - document separate pointstick button bits for V2 devices
  Input: atmel_mxt_ts - add support for Google Pixel 2
  Input: xpad - add rumble support for Xbox One controller
  Input: ff-core - use new debug macros
  Input: add vmmouse driver
  Input: elan_i2c - adjust for newer firmware pressure reporting

My 'allmodconfig' build is _almost_ free of warnings, and most of the
remaining ones are for legacy drivers that just do bad things that I
can't find it in my black heart to care too much about.  But this one
was just annoying me:

   drivers/media/v4l2-core/videobuf2-core.c:3256:26: warning: unused variable ‘fileio’ [-Wunused-variable]

because commit 0e661006 ("[media] vb2: fix 'UNBALANCED' warnings
when calling vb2_thread_stop()") removed all users of 'fileio' and
instead calls "__vb2_cleanup_fileio(q)" to clean up q->fileio.  But the
now unused 'fileio' variable was left around.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Prepare second round of updates for 4.1 merge window.

Pull media updates from Mauro Carvalho Chehab:

 - a new frontend driver for new ATSC devices: lgdt3306a

 - a new sensor driver: ov2659

 - a new platform driver: xilinx

 - the m88ts2022 tuner driver was merged at ts2020 driver

 - the media controller gained experimental support for DVB and hybrid
   devices

 - lots of random cleanups, fixes and improvements on media drivers

* tag 'media/v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (404 commits)
  [media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
  [media] uvcvideo: fix cropcap v4l2-compliance failure
  [media] media: omap3isp: remove unused clkdev
  [media] coda: Add tracing support
  [media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
  [media] coda: fix fill bitstream errors in nonstreaming case
  [media] coda: call SEQ_END when the first queue is stopped
  [media] coda: fail to start streaming if userspace set invalid formats
  [media] coda: remove duplicate error messages for buffer allocations
  [media] coda: move parameter buffer in together with context buffer allocation
  [media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
  [media] coda: allocate per-context buffers from REQBUFS
  [media] coda: use strlcpy instead of snprintf
  [media] coda: bitstream payload is unsigned
  [media] coda: fix double call to debugfs_remove
  [media] coda: check kasprintf return value in coda_open
  [media] coda: bitrate can only be set in kbps steps
  [media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
  [media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
  [media] coda: set allow_zero_bytesused flag for vb2_queue_init
  ...

Pull char/misc driver updates from Greg KH:
 "Here's the big char/misc driver patchset for 4.1-rc1.

  Lots of different driver subsystem updates here, nothing major, full
  details are in the shortlog.

  All of this has been in linux-next for a while"

* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
  mei: trace: remove unused TRACE_SYSTEM_STRING
  DTS: ARM: OMAP3-N900: Add lis3lv02d support
  Documentation: DT: lis302: update wakeup binding
  lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
  lis3lv02d: DT: use s32 to support negative values
  Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
  Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
  mei: replace check for connection instead of transitioning
  mei: use mei_cl_is_connected consistently
  mei: fix mei_poll operation
  hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
  Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
  Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
  Drivers: hv: hv_balloon: do not online pages in offline blocks
  hv: remove the per-channel workqueue
  hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
  hv: run non-blocking message handlers in the dispatch tasklet
  coresight: moving to new "hwtracing" directory
  coresight-tmc: Adding a status interface to sysfs
  coresight: remove the unnecessary configuration coresight-default-sink
  ...

Pull tty/serial updates from Greg KH:
 "Here's the big tty/serial driver update for 4.1-rc1.

  It was delayed for a bit due to some questions surrounding some of the
  console command line parsing changes that are in here.  There's still
  one tiny regression for people who were previously putting multiple
  console command lines and expecting them all to be ignored for some
  odd reason, but Peter is working on fixing that.  If not, I'll send a
  revert for the offending patch, but I have faith that Peter can
  address it.

  Other than the console work here, there's the usual serial driver
  updates and changes, and a buch of 8250 reworks to try to make that
  driver easier to maintain over time, and have it support more devices
  in the future.

  All of these have been in linux-next for a while"

* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
  n_gsm: Drop unneeded cast on netdev_priv
  sc16is7xx: expose RTS inversion in RS-485 mode
  serial: 8250_pci: port failed after wakeup from S3
  earlycon: 8250: Document kernel command line options
  earlycon: 8250: Fix command line regression
  earlycon: Fix __earlycon_table stride
  tty: clean up the tty time logic a bit
  serial: 8250_dw: only get the clock rate in one place
  serial: 8250_dw: remove useless ACPI ID check
  dmaengine: hsu: move memory allocation to GFP_NOWAIT
  dmaengine: hsu: remove redundant pieces of code
  serial: 8250_pci: add Intel Tangier support
  dmaengine: hsu: add Intel Tangier PCI ID
  serial: 8250_pci: replace switch-case by formula for Intel MID
  serial: 8250_pci: replace switch-case by formula
  tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
  serial: jsm: some off by one bugs
  serial: xuartps: Fix check in console_setup().
  serial: xuartps: Get rid of register access macros.
  serial: xuartps: Fix iobase use.
  ...

Pull pincontrol Kconfig fix from Linus Walleij:
 "This fixes the annoying Kconfig noise from pin control.  Mea Culpa"

* tag 'pinctrl-v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: fix allmodconfig noise

Pull clock framework updates from Michael Turquette:
 "The changes to the common clock framework for 4.0 are mostly new clock
  drivers and updates to existing ones for feature enhancements and bug
  fixes.

  There is more churn than usual in the framework core due to the change
  to introduce per-user unique struct clk pointers in 4.0.  This caused
  several regressions to surface, some of which were sent as fixes to
  4.0.  New generic clock drivers were added for GPIO- and PWM-based
  clock controllers.

  Additionally the common clk-divider code recieved several fixes to the
  way it rounds rates"

* tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (91 commits)
  clk: check ->determine/round_rate() return value in clk_calc_new_rates
  clk: at91: usb: propagate rate modification to the parent clk
  clk: samsung: exynos4: Disable ARMCLK down feature on Exynos4210 SoC
  clk: don't use __initconst for non-const arrays
  clk: at91: change to using endian agnositc IO
  clk: clk-gpio-gate: Fix active low
  clk: Add PWM clock driver
  clk: Add clock driver for mb86s7x
  clk: pxa: pxa3xx: add missing os timer clock
  clk: tegra: Use the proper parent for plld_dsi
  clk: tegra: Use generic tegra_osc_clk_init() on Tegra114
  clk: tegra: Model oscillator as clock
  clk: tegra: Add peripheral registers for bank Y
  clk: tegra: Register the proper number of resets
  clk: tegra: Remove needless initializations
  clk: tegra: Use consistent indentation
  clk: tegra: Various whitespace cleanups
  clk: tegra: Enable HDA to HDMI clocks on Tegra124
  clk: tegra: Fix a bunch of sparse warnings
  clk: tegra: Fix typo tabel -> table
  ...

This reverts commit e2ac55b6.

Huang Ying reports that this causes a hang at boot with debugfs disabled.

It is true that the debugfs error checks are kind of confusing, and this
code certainly merits more cleanup and thinking about it, but there's
something wrong with the trivial "check not just for NULL, but for error
pointers too" patch.

Yes, with debugfs disabled, we will end up setting the o2hb_debug_dir
pointer variable to an error pointer (-ENODEV), and then continue as if
everything was fine.  But since debugfs is disabled, all the _users_ of
that pointer end up being compiled away, so even though the pointer can
not be dereferenced, that's still fine.

So it's confusing and somewhat questionable, but the "more correct"
error checks end up causing more trouble than they fix.
Reported-by: Huang Ying <ying.huang@intel.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Chengyu Song <csong84@gatech.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
  media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
  hexdump: avoid warning in test function
  fs: take i_mutex during prepare_binprm for set[ug]id executables
  smp: Fix error case handling in smp_call_function_*()
  iommu-common: Fix PARISC compile-time warnings
  sparc: Make LDC use common iommu poll management functions
  sparc: Make sparc64 use scalable lib/iommu-common.c functions
  Break up monolithic iommu table/lock into finer graularity pools and lock
  sparc: Revert generic IOMMU allocator.
  tools/power turbostat: correct dumped pkg-cstate-limit value
  tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
  tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
  tools/power turbostat: Initial Skylake support
  tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
  tools/power turbostat: modprobe msr, if needed
  tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
  tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
  Bluetooth: hidp: Fix regression with older userspace and flags validation
  config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
  perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
  ...

That solves several merge conflicts:
	Documentation/DocBook/media/v4l/subdev-formats.xml
	Documentation/devicetree/bindings/vendor-prefixes.txt
	drivers/staging/media/mn88473/mn88473.c
	include/linux/kconfig.h
	include/uapi/linux/media-bus-format.h

The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.

* patchwork: (404 commits)
  [media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
  [media] uvcvideo: fix cropcap v4l2-compliance failure
  [media] media: omap3isp: remove unused clkdev
  [media] coda: Add tracing support
  [media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
  [media] coda: fix fill bitstream errors in nonstreaming case
  [media] coda: call SEQ_END when the first queue is stopped
  [media] coda: fail to start streaming if userspace set invalid formats
  [media] coda: remove duplicate error messages for buffer allocations
  [media] coda: move parameter buffer in together with context buffer allocation
  [media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
  [media] coda: allocate per-context buffers from REQBUFS
  [media] coda: use strlcpy instead of snprintf
  [media] coda: bitstream payload is unsigned
  [media] coda: fix double call to debugfs_remove
  [media] coda: check kasprintf return value in coda_open
  [media] coda: bitrate can only be set in kbps steps
  [media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
  [media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
  [media] coda: set allow_zero_bytesused flag for vb2_queue_init
  ...