- 06 Jun, 2019 1 commit
-
-
Biao Huang authored
add Ethernet power on/off operations in init/exit flow. Signed-off-by: Biao Huang <biao.huang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 05 Jun, 2019 39 commits
-
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra likely() call around the !IS_ERR() is not needed. Signed-off-by: Enrico Weigelt <info@metux.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra unlikely() call around IS_ERR() is not needed. Signed-off-by: Enrico Weigelt <info@metux.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra unlikely() call around IS_ERR() is not needed. Signed-off-by: Enrico Weigelt <info@metux.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra likely() call around the !IS_ERR() is not needed. Signed-off-by: Enrico Weigelt <info@metux.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Enrico Weigelt authored
IS_ERR() already calls unlikely(), so this extra likely() call around the !IS_ERR() is not needed. Signed-off-by: Enrico Weigelt <info@metux.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Gustavo A. R. Silva authored
One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct nfp_tun_active_tuns { ... struct route_ip_info { __be32 ipv4; __be32 egress_port; __be32 extra[2]; } tun_info[]; }; Make use of the struct_size() helper instead of an open-coded version in order to avoid any potential type mistakes. So, replace the following form: sizeof(struct nfp_tun_active_tuns) + sizeof(struct route_ip_info) * count with: struct_size(payload, tun_info, count) This code was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lihong Yang authored
The PF driver state flag __I40E_VIRTCHNL_OP_PENDING needs to be checked and set at the beginning of i40e_ndo_set_vf_mac. Otherwise, if there are error conditions before it, the flag will be cleared unexpectedly by this function to cause potential race conditions. Hence move the check to the top of this function. Signed-off-by: Lihong Yang <lihong.yang@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lihong Yang authored
The VF configuration returned in i40e_ndo_get_vf_config is already stored by the PF. There is no dependency on any specific state of the VF to return the configuration. Drop the check against I40E_VF_STATE_INIT since it is not needed. Signed-off-by: Lihong Yang <lihong.yang@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 10GbE Intel Wired LAN Driver Updates 2019-06-05 This series contains updates to mainly ixgbe, with a few updates to i40e, net, ice and hns2 driver. Jan adds support for tracking each queue pair for whether or not AF_XDP zero copy is enabled. Also updated the ixgbe driver to use the netdev-provided umems so that we do not need to contain these structures in our own adapter structure. William Tu provides two fixes for AF_XDP statistics which were causing incorrect counts. Jake reduces the PTP transmit timestamp timeout from 15 seconds to 1 second, which is still well after the maximum expected delay. Also fixes an issues with the PTP SDP pin setup which was not properly aligning on a full second, so updated the code to account for the cyclecounter multiplier and simplify the code to make the intent of the calculations more clear. Updated the function header comments to help with the code documentation. Added support for SDP/PPS output for x550 devices, which is slightly different than x540 devices that currently have this support. Anirudh adds a new define for Link Layer Discovery Protocol to the networking core, so that drivers do not have to create and use their own definitions. In addition, update all the drivers currently defining their own LLDP define to use the new networking core define. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Kangjie Lu authored
If ixgbevf_write_msg_read_ack fails, return its error code upstream Signed-off-by: Kangjie Lu <kjlu@umn.edu> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
Similar to the X540 hardware, enable support for generating a 1pps output signal on SDP0. This support is slightly different to the X540 hardware, because of the register layout changes. First, the system time register is now represented in 'cycles' and 'billions of cycles'. Second, we need to also program the TSSDP register, as well as the ESDP register. Third, the clock output uses only FREQOUT, instead of a full 64bit value for the output clock period. Finally, we have to use the ST0 bit instead of the SYNCLK bit in the TSAUXC register. This support should work even for the hardware with a higher frequency clock, as it carefully takes into account the multiply and shift of the cycle counter used. We also set the pps configuration to 1, since we now support generating a pulse per second output. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Anirudh Venkataramanan authored
Remove references to HCLGE_MAC_ETHERTYPE_LLDP and use ETH_P_LLDP instead. Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jeff Kirsher authored
Instead of using a local define for the LLDP ethertype, use the kernel define ETH_P_LLDP. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Anirudh Venkataramanan authored
Remove references to IXGBE_ETH_P_LLD and use ETH_P_LLDP instead. Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Anirudh Venkataramanan authored
Remove references to I40E_ETH_P_LLDP and use ETH_P_LLDP instead. Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Anirudh Venkataramanan authored
Add a new define ETH_P_LLDP for Link Layer Discovery Protocol (LLDP) ethertype. Suggested-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
This function was missing a documentation comment. Add one now. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
The ixgbe_ptp.c file sometimes uses hw_cc as the local variable for the cycle counter in ixgbe_ptp_read_X550. However, we use just 'cc' as a local variable for this by convention else where in the file. Convert this lone usage of 'hw_cc' into just the shorter 'cc' name to match the other read functions in the file. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
The function ixgbe_ptp_setup_sdp_X540 attempts to program a software defined pin, in order to generate a pulse-per-second output on SDP 0. It does work to generate the output, but does not align the output on the full second. Additionally, it does not take into account the cyclecounter multiplier. This leads to somewhat confusing code which is likely to be incorrect if blindly copied to another hardware type. Update this code to account for the cyclecounter multiplier, and to directly use timecounter_read. This change ensures that the SDP output will align properly on a full second, and makes the intent of the calculations a bit more clear. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jacob Keller authored
Previously we waited for a whole 15 seconds before we cleared the Tx timestamp state. This is astronomically long compared to the worst case timings expected by our devices. In addition, this is longer than the wait in ptp4l when it detects a fault (caused by missing Tx timestamps). Thus, reduce the timer to only 1 second, which is well after the maximum expected delay. This should reduce user frustration when a timestamp does get dropped for some reason. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
William Tu authored
The total_packets count at ixgbe_clean_xdp_tx_irq is always zero when testing with xdpsock -t -N. Set the gso_segs to 1 to make the tx packet count correct. Signed-off-by: William Tu <u9012063@gmail.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
William Tu authored
The tx bytecount is done twice. When running './xdpsock -t -N -i eth3' and 'ip -s link show dev eth3' The avg packet size is 120 instead of 60. So remove the extra one. Signed-off-by: William Tu <u9012063@gmail.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jan Sokolowski authored
As current implementation of netdev already contains and provides umems for us, we no longer have the need to contain these structures in ixgbe_adapter. Refactor the code to operate on netdev-provided umems. Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Jan Sokolowski authored
Here, we add a bitmap to the ixgbe_adapter that tracks if a certain queue pair has been "zero-copy enabled" via the ndo_bpf. The bitmap is used in ixgbe_xsk_umem, and enables zero-copy if and only if XDP is enabled, the corresponding qid in the bitmap is set, and the umem is non-NULL; Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Fabio Estevam authored
dev_err() is more appropriate for printing error messages inside drivers, so switch to dev_err(). Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Heiner Kallweit says: ==================== r8169: factor out firmware handling Let's factor out firmware handling into a separate source code file. This simplifies reading the code and makes clearer what the interface between driver and firmware handling is. v2: - fix small whitespace issue in patch 2 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Let's factor out firmware handling into a separate source code file. This simplifies reading the code and makes clearer what the interface between driver and firmware handling is. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
In preparation of factoring out firmware handling rename r8169.c to r8169_main.c. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Randy Dunlap authored
Fix build errors in Mediatek mtk_eth_soc driver. It looks like these 3 source files were meant to be linked together since 2 of them are library-like functions, but they are currently being built as 3 loadable modules. Fixes these build errors: WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/mediatek/mtk_eth_path.o WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/mediatek/mtk_sgmii.o ERROR: "mtk_sgmii_init" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined! ERROR: "mtk_setup_hw_path" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined! ERROR: "mtk_sgmii_setup_mode_force" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined! ERROR: "mtk_sgmii_setup_mode_an" [drivers/net/ethernet/mediatek/mtk_eth_soc.ko] undefined! ERROR: "mtk_w32" [drivers/net/ethernet/mediatek/mtk_eth_path.ko] undefined! ERROR: "mtk_r32" [drivers/net/ethernet/mediatek/mtk_eth_path.ko] undefined! This changes the loadable module name from mtk_eth_soc to mtk_eth. I didn't see a way to leave it as mtk_eth_soc. Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Sean Wang <sean.wang@mediatek.com> Cc: John Crispin <blogic@openwrt.org> Cc: Felix Fietkau <nbd@openwrt.org> Cc: Nelson Chang <nelson.chang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Rasmus Villemoes says: ==================== net: dsa: mv88e6xxx: support for mv88e6250 This adds support for the mv88e6250 chip. Initially based on the mv88e6240, this time around, I've been through each ->ops callback and checked that it makes sense, either replacing with a 6250 specific variant or dropping it if no equivalent functionality seems to exist for the 6250. Along the way, I found a few oddities in the existing code, mostly sent as separate patches/questions. The one relevant to the 6250 is the ieee_pri_map callback, where the existing mv88e6085_g1_ieee_pri_map() is actually wrong for many of the existing users. I've put the mv88e6250_g1_ieee_pri_map() patch first in case some of the existing chips get switched over to use that and it is deemed important enough for -stable. v4: - fix style issue in 1/10 - add Andrew's reviewed-by to 1,6,7,8,9,10. v3: - rebase on top of net-next/master - add reviewed-bys to patches unchanged from v2 (2,3,4,5) - add 6250-specific ->ieee_pri_map, ->port_set_speed, ->port_link_state (1,6,7) - in addition, use mv88e6065_phylink_validate for ->phylink_validate, and don't implement ->port_get_cmode, ->port_set_jumbo_size, ->port_disable_learn_limit, ->rmu_disable - drop ptp support - add patch adding the compatible string to the DT binding (9) - add small refactoring patch (10) v2: - rebase on top of net-next/master - add reviewed-by to two patches unchanged from v1 (2,3) - add separate watchdog_ops ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
The new mv88e6250_g1_reset() is identical to mv88e6352_g1_reset() except for the call of mv88e6352_g1_wait_ppu_polling(), so refactor the 6352 version in term of the 6250 one. No functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
The mv88e6250 has port_base_addr 0x8 or 0x18 (depending on configuration pins), so it constitutes a new family and hence needs its own compatible string. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
This adds support for the Marvell 88E6250. I've checked that each member in the ops-structure makes sense, and basic switchdev functionality works fine. It uses the new dual_chip option, and since its port registers start at SMI address 0x08 or 0x18 (i.e., always sw_addr + 0x08), we need to introduce a new compatible string in order for the auto-identification in mv88e6xxx_detect() to work. The chip has four per port 16-bits statistics registers, two of which correspond to the existing "sw_in_filtered" and "sw_out_filtered" (but at offsets 0x13 and 0x10 rather than 0x12 and 0x13, because why should this be easy...). Wiring up those four statistics seems to require introducing a STATS_TYPE_PORT_6250 bit or similar, which seems a tad ugly, so for now this just allows access to the STATS_TYPE_BANK0 ones. The chip does have ptp support, and the existing mv88e6352_{gpio,avb,ptp}_ops at first glance seem like they would work out-of-the-box, but for simplicity (and lack of testing) I'm eliding this. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
The mv88e6250 has a rather different way of reporting the link, speed and duplex status. A simple difference is that the link bit is bit 12 rather than bit 11 of the port status register. It gets more complicated for speed and duplex, which do not have separate fields. Instead, there's a four-bit PortMode field, and decoding that depends on whether it's a phy or mii port. For the phy ports, only four of the 16 values have defined meaning; the rest are called "reserved", so returning {SPEED,DUPLEX}_UNKNOWN seems reasonable. For the mii ports, most possible values are documented (0x3 and 0x5 are reserved), but I'm unable to make sense of them all. Since the bits simply reflect the Px_MODE[3:0] configuration pins, just support the subset that I'm certain about. Support for other setups can be added later. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
The data sheet also mentions the possibility of selecting 200 Mbps for the MII ports (ports 5 and 6) by setting the ForceSpd field to 0x2 (aka MV88E6065_PORT_MAC_CTL_SPEED_200). However, there's a note that "actual speed is determined by bit 8 above", and flipping back a page, one finds that bits 13:8 are reserved... So without further information on what bit 8 means, let's stick to supporting just 10 and 100 Mbps on all ports. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
The MV88E6352_G2_WDOG_CTL_* bits almost, but not quite, describe the watchdog control register on the mv88e6250. Among those actually referenced in the code, only QC_ENABLE differs (bit 6 rather than bit 5). Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
These are almost identical to the 6185 variants, but have fewer bits for the FID. Bit 10 of the VTU_OP register (offset 0x05) is the VidPolicy bit, which one should probably preserve in mv88e6xxx_g1_vtu_op(), instead of always writing a 0. However, on the 6352 family, that bit is located at bit 12 in the VTU FID register (offset 0x02), and is always unconditionally cleared by the mv88e6xxx_g1_vtu_fid_write() function. Since nothing in the existing driver seems to know or care about that bit, it seems reasonable to not add the boilerplate to preserve it for the 6250 (which would require adding a chip-specific vtu_op function, or adding chip-quirks to the existing one). Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
All the currently supported chips have .num_databases either 256 or 4096, so this patch does not change behaviour for any of those. The mv88e6250, however, has .num_databases == 64, and it does not put the upper two bits in ATU control 13:12, but rather in ATU Operation 9:8. So change the logic to prepare for supporting mv88e6250. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Rasmus Villemoes authored
The 88e6250 (as well as 6220, 6071, 6070, 6020) do not support multi-chip (indirect) addressing. However, one can still have two of them on the same mdio bus, since the device only uses 16 of the 32 possible addresses, either addresses 0x00-0x0F or 0x10-0x1F depending on the ADDR4 pin at reset [since ADDR4 is internally pulled high, the latter is the default]. In order to prepare for supporting the 88e6250 and friends, introduce mv88e6xxx_info::dual_chip to allow having a non-zero sw_addr while still using direct addressing. Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
-