Merge tag 'linux-can-fixes-for-4.7-20160623' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-06-23

this is a pull request of 3 patches for the upcoming linux-4.7 release.

The first two patches are by Oliver Hartkopp fixing oopes in the generic CAN
device netlink handling. Jimmy Assarsson's patch for the kvaser_usb driver adds
support for more devices by adding their USB product ids.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

By default, mdiobus_alloc() sets the PHYs to polling mode, but a
pointer size memcpy means that a couple IRQs end up being overwritten
with a value of 0. This means that PHY_POLL is disabled and results
in unpredictable behavior depending on the PHY's location on the
MDIO bus. Remove that memcpy and the now unused phy_irq member to
force the SMSC911x PHYs into polling mode 100% of the time.

Fixes: e7f4dc35 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tariq Toukan is replacing Eugenia (Jenny) Emantayev as the mlx4
Ethernet driver maintainer, thanks to Jenny and good luck to him.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.7

iwlwifi

* fix the scan timeout for long scans
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted

rtl8xxxu

* fix typo on variable name

ath10k

* fix deadlock when peer cannot be created
* fix crash related to printing features
* fix deadlock while processing rx_in_ord_ind

ath9k

* fix GPIO mask regression for AR9462 and AR9565
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tx errors present summation of errors encountered while transmitting
packets.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The assignment of rth->dst.output in vrf_rt6_create() and
vrf_rtable_create() used a hard tab before the '='. The neighboring
assignments did not. Make the assignment of rth->dst.output consistent
with the surrounding code.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the packet was dropped by lower qdisc, then we must not
access it later.

Save qdisc_pkt_len(skb) in a temp variable.

Fixes: 2ccccf5f ("net_sched: update hierarchical backlog too")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexey reported that we have GFP_KERNEL allocation when
holding the spinlock tcf_lock. Actually we don't have
to take that spinlock for all the cases, especially
for the new one we just create. To modify the existing
actions, we still need this spinlock to make sure
the whole update is atomic.

For net-next, we can get rid of this spinlock because
we already hold the RTNL lock on slow path, and on fast
path we can use RCU to protect the metalist.

Joint work with Jamal.
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Blair Steven noticed that ESN in conjunction with UDP encapsulation
is broken because we set the temporary ESP header to the wrong spot.

This patch fixes this by first of all using the right spot, i.e.,
4 bytes off the real ESP header, and then saving this information
so that after encryption we can restore it properly.

Fixes: 7021b2e1 ("esp4: Switch to new AEAD interface")
Reported-by: Blair Steven <Blair.Steven@alliedtelesis.co.nz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for Kvaser Leaf Light HS v2 OEM, Mini PCI
Express 2xHS and USBcan Light 2xHS.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...

This patch adds a private dellink function for the CAN device driver interface
that does just nothing.

It's a follow up to commit 993e6f2f ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

With upstream commit bb208f14 (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.

When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Tariq Toukan says:

====================
mlx4_en fixes for 4.7-rc

This small patchset includes two small fixes for mlx4_en driver.

One allows a clean shutdown even when clients do not release their
netdev reference.
The other adds error return values to the VLAN VID add/kill functions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows a clean shutdown, even if some netdev clients do not
release their reference from this netdev. It is enough to release
the HW resources only as the kernel is shutting down.

Fixes: 2ba5fbd6 ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify mlx4_en_vlan_rx_[add/kill]_vid to return error value in case of
failure.

Fixes: 8e586137 ('net: make vlan ndo_vlan_rx_[add/kill]_vid return error value')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When extracting an individual message from a received "bundle" buffer,
we just create a clone of the base buffer, and adjust it to point into
the right position of the linearized data area of the latter. This works
well for regular message reception, but during periods of extremely high
load it may happen that an extracted buffer, e.g, a connection probe, is
reversed and forwarded through an external interface while the preceding
extracted message is still unhandled. When this happens, the header or
data area of the preceding message will be partially overwritten by a
MAC header, leading to unpredicatable consequences, such as a link
reset.

We now fix this by ensuring that the msg_reverse() function never
returns a cloned buffer, and that the returned buffer always contains
sufficient valid head and tail room to be forwarded.
Reported-by: Erik Hugne <erik.hugne@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every open of /proc/net/kcm leaks 16 bytes of memory as is reported by
kmemleak:
unreferenced object 0xffff88059c0e3458 (size 192):
  comm "cat", pid 1401, jiffies 4294935742 (age 310.720s)
  hex dump (first 32 bytes):
    28 45 71 96 05 88 ff ff 00 10 00 00 00 00 00 00  (Eq.............
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff8156a2de>] kmem_cache_alloc_trace+0x16e/0x230
    [<ffffffff8162a479>] seq_open+0x79/0x1d0
    [<ffffffffa0578510>] kcm_seq_open+0x0/0x30 [kcm]
    [<ffffffff8162a479>] seq_open+0x79/0x1d0
    [<ffffffff8162a8cf>] __seq_open_private+0x2f/0xa0
    [<ffffffff81712548>] seq_open_net+0x38/0xa0
...

It is caused by a missing free in the ->release path. So fix it by
providing seq_release_net as the ->release method.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: cd6e111b (kcm: Add statistics and proc interfaces)
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tom Herbert <tom@herbertland.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Both dev_uc_sync_multiple() and dev_mc_sync_multiple() require the
source device to be locked by netif_addr_lock_bh(), but this is missing
in team's enslave function, so add it.

This fixes the following lockdep warning:

Possible interrupt unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(_xmit_ETHER/1);
                                local_irq_disable();
                                lock(&(&mc->mca_lock)->rlock);
                                lock(&team_netdev_addr_lock_key);
   <Interrupt>
     lock(&(&mc->mca_lock)->rlock);

  *** DEADLOCK ***

Fixes: cb41c997 ("team: team should sync the port's uc/mc addrs when add a port")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.7-20160620' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-06-20

this is a pull request of 3 patches for the upcoming linux-4.7 release.

The first patch is by Thor Thayer for the c_can/d_can driver. It fixes the
registar access on Altera Cyclone devices, which caused CAN frames to have 0x0
in the first two bytes incorrectly. Wolfgang Grandegger's patch for the at91
driver fixes a hanging driver under high bus load situations. A patch for the
gs_usb driver by Maximilian Schneider adds support for the bytewerk.org
candleLight interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patchs adds basic support for the bytewerk.org candleLight interface,
a open hardware (CERN OHL) USB CAN adapter.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de>
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Amr Bekhit <amrbekhit@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.

The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.

Testing performed on Altera CycloneV (D_CAN).  Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Yuval Mintz says:

====================
qed*: Fixes series

This series contains several small fixes to driver behavior
[4th patch is the only one containing a 'fatal' fix, but the error
is only theoretical for qede; if would require another protocol
driver yet unsubmitted to reach it].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'MODULE_FIBER' value replaced several other FIBER values
in newer management firmware images, so existing code would
fail to properly reflect its mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver has 2 sets of entries for handling ramrod configurations
toward firmware - a regular pre-allocated set of entires and a
possible 'unlimited' list of additional pending entries.

In most scenarios the 'unlimited' list would not be used, but
when it does the handling of the ramrod completion doesn't
properly handle the release of the entry.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several user APIs can cause driver to perform an inner-reload.
Currently, doing this would cause the HW/FW statistics of the
adapter to reset, which isn't the expected behavior [statistics
should only reset on explicit unloads].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Internal loopback in driver is based on two things - first
is the willingness of transmitter to use it [in case of VFs,
this can be forced based on VEPA/VEB] and secondly on another
vport classification configuration which should match the
packet's destination.

Current code allows non-linux VFs to configure a 'promisc'
mode on Tx, meaning all traffic sent by VF would be loopbacked
internally by firmware; This isn't considered a valid mode and
as such should be prevented by PF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When no vlan filter is configured, firmware has a configurable
default on whether to pass only untagged packets or all packets
regardless of their tagging. Driver currently doesn't set this
field in the necessary ramrod, causing the default to always be
'receive all'.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix coding style issues in the following files:

ib_cm.c:      add space
loop.c:       convert spaces to tabs
sysctl.c:     add space
tcp.h:        convert spaces to tabs
tcp_connect.c:remove extra indentation in switch statement
tcp_recv.c:   convert spaces to tabs
tcp_send.c:   convert spaces to tabs
transport.c:  move brace up one line on for statement
Signed-off-by: Joshua Houghton <josh@awful.name>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A socket connection made in ax.25 is not closed when session is
completed.  The heartbeat timer is stopped prematurely and this is
where the socket gets closed. Allow heatbeat timer to run to close
socket. Symptom occurs in kernels >= 4.2.0

Originally sent 6/15/2016. Resend with distribution list matching
scripts/maintainer.pl output.
Signed-off-by: Basil Gunn <basil@pacabunga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The state of the rds_connection after rds_tcp_reset_callbacks() would
be RDS_CONN_RESETTING and this is the value that should be passed
by rds_tcp_accept_one()  to rds_connect_path_complete() to transition
the socket to RDS_CONN_UP.

Fixes: b5c21c0947c1 ("RDS: TCP: fix race windows in send-path quiescence
by rds_tcp_accept_one()")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The conversion to the 64-bit time based ptp methods left two instances
of 'struct timespec' in place. This is harmless because 64-bit
architectures define timespec64 as timespec, and this driver is
not used on 32-bit machines.

However, using 'struct timespec64' directly is obviously the right
thing to do, and will help us remove 'struct timespec' in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b9acf24f ("ptp: tilegx: convert to the 64 bit get/set time methods.")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: couple of fixes

Couple of slowpath tx stats fixes for Spectrum and SwitchX-2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Stop the SW TX counter from counting the TX header bytes
since they are not being sent out.

Fixes: e577516b ("mlxsw: Fix use-after-free bug in mlxsw_sx_port_xmit")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stop the SW TX counter from counting the TX header bytes
since they are not being sent out.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We sometimes observe a 'deadly embrace' type deadlock occurring
between mutually connected sockets on the same node. This happens
when the one-hour peer supervision timers happen to expire
simultaneously in both sockets.

The scenario is as follows:

CPU 1:                          CPU 2:
--------                        --------
tipc_sk_timeout(sk1)            tipc_sk_timeout(sk2)
  lock(sk1.slock)                 lock(sk2.slock)
  msg_create(probe)               msg_create(probe)
  unlock(sk1.slock)               unlock(sk2.slock)
  tipc_node_xmit_skb()            tipc_node_xmit_skb()
    tipc_node_xmit()                tipc_node_xmit()
      tipc_sk_rcv(sk2)                tipc_sk_rcv(sk1)
        lock(sk2.slock)                 lock((sk1.slock)
        filter_rcv()                    filter_rcv()
          tipc_sk_proto_rcv()             tipc_sk_proto_rcv()
            msg_create(probe_rsp)           msg_create(probe_rsp)
            tipc_sk_respond()               tipc_sk_respond()
              tipc_node_xmit_skb()            tipc_node_xmit_skb()
                tipc_node_xmit()                tipc_node_xmit()
                  tipc_sk_rcv(sk1)                tipc_sk_rcv(sk2)
                    lock((sk1.slock)                lock((sk2.slock)
                    ===> DEADLOCK                   ===> DEADLOCK

Further analysis reveals that there are three different locations in the
socket code where tipc_sk_respond() is called within the context of the
socket lock, with ensuing risk of similar deadlocks.

We now solve this by passing a buffer queue along with all upcalls where
sk_lock.slock may potentially be held. Response or rejected message
buffers are accumulated into this queue instead of being sent out
directly, and only sent once we know we are safely outside the slock
context.
Reported-by: GUNA <gbalasun@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are rather small patches but fixing several outstanding bugs in
nf_conntrack and nf_tables, as well as minor problems with missing
SYNPROXY header uapi installation:

1) Oneliner not to leak conntrack kmemcache on module removal, this
   problem was introduced in the previous merge window, patch from
   Florian Westphal.

2) Two fixes for insufficient ruleset loop validation, one due to
   incorrect flag check in nf_tables_bind_set() and another related to
   silly wrong generation mask logic from the walk path, from Liping
   Zhang.

3) Fix double-free of anonymous sets on error, this fix simplifies the
   code to let the abort path take care of releasing the set object,
   also from Liping Zhang.

4) The introduction of helper function for transactions broke the skip
   inactive rules logic from the nft_do_chain(), again from Liping
   Zhang.

5) Two patches to install uapi xt_SYNPROXY.h header and calm down
   kbuild robot due to missing #include <linux/types.h>.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

./usr/include/linux/netfilter/xt_SYNPROXY.h:11: found __[us]{8,16,32,64} type without #include <linux/types.h>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Matt Whitlock says:

 Without this line, the file xt_SYNPROXY.h does not get installed in
 /usr/include/linux/netfilter/, and thus user-space programs cannot make
 use of it.
Reported-by: Matt Whitlock <kernel@mattwhitlock.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>