This change adds support for the Power Enable Key found on MFD AXP202
and AXP209. Besides the basic support for the button, the driver adds
two entries in sysfs to configure the time delay for power on/off.
Signed-off-by: Carlo Caione <carlo@caione.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[wens@csie.org: made axp20x_pek_remove() static; removed driver owner
 field; fixed path for sysfs entries]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If given input handler is not a filter there is no point is iterating list
of events in a packet to see if some of them need to be filtered out.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If a device does not support autorepeat or does not emit any key events we
should not be scanning all events in a packet to decide if we should start
or stop autorepeat function.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to Documentation/CodingStyle - Chapter 14:

"The preferred form for passing a size of a struct is the following:

        p = kmalloc(sizeof(*p), ...);

The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."

So do it as recommended.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

synaptics_profile_sensor_process() and synaptics_report_mt_data() now
share the exact same code. Remove one implementation and rely on the
other where it was used.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The current code tries to consider all states and transitions to properly
detect which finger is attached to which slot. The code is quite huge
and difficult to read.

If the sensor manages to group the touch points but is not reliable in
giving tracking ids, we can simply use the kernel tracking method. Note
that it is already used by Cr-48 Chromebooks.

Incidentaly, this fixes a bug reported by Peter Hutterer:
"""
on the Lenovo T440, run:
evemu-record /dev/input/event4 | grep BTN_

then put one, two, three, two fingers down
when you go from 3 to 2 fingers the driver sends a spurious BTN_TOUCH 0
event:

E: 0.000000 0001 014a 0001      # EV_KEY / BTN_TOUCH            1
E: 0.000000 0001 0145 0001      # EV_KEY / BTN_TOOL_FINGER      1
E: 0.770008 0001 0145 0000      # EV_KEY / BTN_TOOL_FINGER      0
E: 0.770008 0001 014d 0001      # EV_KEY / BTN_TOOL_DOUBLETAP   1
E: 1.924716 0001 014d 0000      # EV_KEY / BTN_TOOL_DOUBLETAP   0
E: 1.924716 0001 014e 0001      # EV_KEY / BTN_TOOL_TRIPLETAP   1

.. changing from 3 to 2 fingers now

E: 3.152641 0001 014a 0000      # EV_KEY / BTN_TOUCH            0
E: 3.152641 0001 014d 0001      # EV_KEY / BTN_TOOL_DOUBLETAP   1
E: 3.152641 0001 014e 0000      # EV_KEY / BTN_TOOL_TRIPLETAP   0
E: 3.176948 0001 014a 0001      # EV_KEY / BTN_TOUCH            1

quick look in the kernel shows it's caused by hw.z going to 0 for a packet,
so probably a firmware bug. either way, it makes it hard to track BTN_TOUCH
as signal that at least one finger is down.
"""

The in-kernel tracking is enough to remove this spurious BTN_TOUCH 0.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Based on versioncheck.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Most of the protocol for these touchpads has been reverse engineered. This
commit adds a basic multitouch-capable driver.

A lot of the protocol is still unknown. Especially, we don't know how to
identify the device yet apart from the PNP ID.

The previous workaround for these devices has been left in place in case
the driver is not compiled into the kernel or in case some other device
with the same PNP ID is not recognized by the driver yet still has the same
problems with the device probing code.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

With this driver, we can report KEY_POWER on AM437x SK. This patch has been
tested with said board.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Allwinnner sunxi SoCs have a low resolution adc (called lradc) which is
specifically designed to have various (tablet) keys (ie home, back, search,
etc). attached to it using a resistor network. This adds a driver for this.

There are 2 channels, currently this driver only supports chan0 since there
are no boards known to use chan1.

This has been tested on an olimex a10s-olinuxino-micro, a13-olinuxino, and
a20-olinuxino-micro.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This change adds support for haptic driver controlled by voltage of a
regulator. Userspace can control the device via Force Feedback interface
from input framework.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyunhee Kim <hyunhee.kim@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add a table documenting where all the bits are in the v7 touchpad packets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Protocol v7 uses the middle / right button bits on clickpads to communicate
"location" information of a 3th touch (and possible 4th) touch on
clickpads.

Specifically when 3 touches are down, if one of the 3 touches is in the
left / right button area, this will get reported in the middle / right
button bits and the touchpad will still send a TWO type packet rather then
a MULTI type packet, so when this happens we must add the finger reported
in the button area to the finger count.

Likewise we must also add fingers reported this way to the finger count
when we get MULTI packets.

BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=86338
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The v7 proto differentiates between a primary touch (with high precision)
and a secondary touch (with lower precision). Normally when 2 fingers are
down and one is lifted the still present touch becomes the primary touch,
but some traces have shown that this does not happen always.

This commit deals with this by making alps_get_mt_count() not stop at the
first empty mt slot, and if a touch is present in mt[1] and not mt[0]
moving the data to mt[0] (for input_mt_assign_slots).

BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=86338
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

NEW packets are send to indicate a discontinuity in the finger coordinate
reporting. Specifically a finger may have moved from slot 0 to 1 or vice
versa.  INPUT_MT_TRACK takes care of this for us.

NEW packets have 3 problems:
1) They do not contain middle / right button info (on non clickpads)
   this can be worked around by preserving the old button state
2) They do not contain an accurate fingercount, and they are
   typically send when the number of fingers changes. We cannot use
   the old finger count as that may mismatch with the amount of
   touch coordinates we've available in the NEW packet
3) Their x data for the second touch is inaccurate leading to
   a possible jump of the x coordinate by 16 units when the first
   non NEW packet comes in

Since problems 2 & 3 cannot be worked around, just ignore them.

BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=86338
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds support for CLOCK_BOOTTIME for input event timestamp.
CLOCK_BOOTTIME includes suspend time, so it would allow aplications
to get correct time difference between two events even when system
resumes from suspend state.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

IBM Trackpoints have a feature to compensate for drift by recalibrating
themselves periodically. By default, if for 0.5 seconds there is no change
in position, it's used as the new zero. This duration is too low. Often,
the calibration happens when the trackpoint is in fact being used.

IBM's Trackpoint Engineering Specifications show a configuration register
that allows changing this duration, rstdft1.

Expose it via sysfs among the other settings.
Signed-off-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

All keypad column pins used as inputs should be pulled up on the STMPE24xx,
but this is not done by the current driver.  Add some logic that will do
this properly. The STMPE1601 also has a keypad controller, but explicitly
does *NOT* require you to set up any pull-ups.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The STMPE keypad controller is only used with device tree configured
systems, so force the configuration to come from device tree only, and now
actually get the rows and cols from the device tree too.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This adds the register offsets for pull up/down for the STMPE
1601, 1801 and 24xx expanders. This is used to bias GPIO lines
and keypad lines.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch avoids unnecessary operations while estimating events per
packet for an input device when event type is not set.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fixed a coding style error, macros with complex values should be
enclosed in parentheses.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We do not need to roll our own implementation of delayed work now that we
have proper implementation of mod_delayed_work.

For interrupt-only driven buttons we retain the timer, but we rename
it to release_timer to better reflect its purpose.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This change allows specify interrupt for buttons separately form gpio,
potentially allowing to form several "clusters" of buttons on
different interrupts.

Button defined without both gpio and irq in device tree is a hared error
instead of a warning now.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit af906faa ("Input: gpio_keys - fix warning regarding uninitialized
'irq' variable") introduced the following build warning:

drivers/input/keyboard/gpio_keys.c:625:16: warning: 'button' may be used uninitialized in this function [-Wmaybe-uninitialized]

Move the 'button' initialization to a proper location to avoid such warning.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This driver supports Elan eKTH I2C touchscreen controllers. Note that these
are using custom protocol, as opposed to other Elan parts that use
HID-over-I2C and are supported by the standard HID-multitouch driver.
Signed-off-by: Scott Liu <scott.liu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit f2d347ff ("Input: gpio_keys - add device tree support for
interrupt only keys") caused the following build warning:

drivers/input/keyboard/gpio_keys.c: In function 'gpio_keys_probe':
drivers/input/keyboard/gpio_keys.c:647:15: warning: 'irq' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/input/keyboard/gpio_keys.c:622:7: note: 'irq' was declared here

Move button->irq initialization into proper branch and get rid of the
temporary.
Reported-by: Olof's autobuilder <build@lixom.net>
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Let's use 'error' variable instead of 'ret' when we need to store erro
codes.
Signed-off-by: Dudley Du <dudley.dulixin@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Chage b1cfa7b4 tried to get away form using
irq in cyapa structure and use client->irq instead, but missed a couple of
spots making the touchpad inoperative after resume.
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dudley Du <dudley.dulixin@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This features already exists for board config setups. Add support for
device tree based systems.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Allocate the temporary buffer needed for initialization of the console
keyboard maps (512 bytes, as NR_KEYS = 256) on the stack instead of
statically, to reduce kernel size.

add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-512 (-512)
function                                     old     new   delta
temp_map                                     512       -    -512
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If CONFIG_HW_CONSOLE is not set:

drivers/built-in.o: In function `amikbd_probe':
amikbd.c:(.init.text+0x3e4e): undefined reference to `key_maps'
amikbd.c:(.init.text+0x3dd4): undefined reference to `key_maps'

To fix this, extract the initialization of the console keyboard maps
into amikbd_init_console_keymaps(), protected by #ifdef
CONFIG_HW_CONSOLE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The missing error handling here is not especially harmful but static
checkers complain that "i" can be used uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Let's initialize atomic_t variables keeping track of number of various
devices created so far with -1 in order to avoid extra subtraction
operation.
Signed-off-by: Aniroop Mathur <aniroop.mathur@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Let's initializes input_no to -1 in order to avoid extra subtraction
operation performed every time we allocate an input device.
Signed-off-by: Aniroop Mathur <aniroop.mathur@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Intel NUC D54250WYK has no PS/2 controller, however the DSDT declares
PS/2 devices which trigger the loading of the i8042 driver.
Signed-off-by: Todor Minchev <todor.minchev@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Without the change either no scancode would be reported on release of
force_release keys, or - if the key is marked as force_release erroneously
- the release event and the scancode would be reported in separate reports
to the input layer.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use of managed resources simplifies error handling and device removal code.
Signed-off-by: Dudley Du <dudl@cypress.com>
[Dmitry: added open/close methods so cyapa_remove is no longer needed.]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

For functions defined in header files we should use static inline rather
than inline, which breaks under the latest upstream gcc (which is really
gcc issue, but static inline is better suited regardless).

The related error (with allmodconfig under tile):

    MODPOST 4002 modules
  ERROR: "lifebook_detect" [drivers/input/mouse/psmouse.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>