- 04 Jun, 2014 8 commits
-
-
Bjørn Mork authored
commit 4d7c0136 upstream. Dan writes: "The Dell drivers use the same configuration for PIDs: 81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card 81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card 81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card 81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card 81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card These devices are all clearly Sierra devices, but are also definitely Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750. >From DellGobi5kSetup.exe from the Dell drivers: usbif0: serial/firmware loader? usbif2: nmea usbif3: modem/ppp usbif8: net/QMI" Cc: <stable@vger.kernel.org> Reported-by:
AceLan Kao <acelan.kao@canonical.com> Reported-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Sergey Popovich authored
commit a8951d58 upstream. Dst is released one line before we access it again with dst->error. Fixes: 58e35d14 netfilter: ipv6: propagate routing errors from ip6_route_me_harder() Signed-off-by:
Sergey Popovich <popovich_sergei@mail.ru> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Johannes Berg authored
commit b4b177a5 upstream. Jouni reported that if a remain-on-channel was active on the same channel as the current operating channel, then the ROC would start, but any frames transmitted using mgmt-tx on the same channel would get delayed until after the ROC. The reason for this is that the ROC starts, but doesn't have any handling for "remain on the same channel", so it stops the interface queues. The later mgmt-tx then puts the frame on the interface queues (since it's on the current operating channel) and thus they get delayed until after the ROC. To fix this, add some logic to handle remaining on the same channel specially and not stop the queues etc. in this case. This not only fixes the bug but also improves behaviour in this case as data frames etc. can continue to flow. Cc: stable@vger.kernel.org Reported-by:
Jouni Malinen <j@w1.fi> Tested-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
David Rientjes authored
commit d49ad935 upstream. When two threads have the same badness score, it's preferable to kill the thread group leader so that the actual process name is printed to the kernel log rather than the thread group name which may be shared amongst several processes. This was the behavior when select_bad_process() used to do for_each_process(), but it now iterates threads instead and leads to ambiguity. Signed-off-by:
David Rientjes <rientjes@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Greg Thelen <gthelen@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Oleg Nesterov authored
commit 4d4048be upstream. find_lock_task_mm() expects it is called under rcu or tasklist lock, but it seems that at least oom_unkillable_task()->task_in_mem_cgroup() and mem_cgroup_out_of_memory()->oom_badness() can call it lockless. Perhaps we could fix the callers, but this patch simply adds rcu lock into find_lock_task_mm(). This also allows to simplify a bit one of its callers, oom_kill_process(). Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Cc: Sergey Dyasly <dserrg@gmail.com> Cc: Sameer Nanda <snanda@chromium.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mandeep Singh Baines <msb@chromium.org> Cc: "Ma, Xindong" <xindong.ma@intel.com> Reviewed-by:
Michal Hocko <mhocko@suse.cz> Cc: "Tu, Xiaobing" <xiaobing.tu@intel.com> Acked-by:
-
Oleg Nesterov authored
commit ad962441 upstream. At least out_of_memory() calls has_intersects_mems_allowed() without even rcu_read_lock(), this is obviously buggy. Add the necessary rcu_read_lock(). This means that we can not simply return from the loop, we need "bool ret" and "break". While at it, swap the names of task_struct's (the argument and the local). This cleans up the code a little bit and avoids the unnecessary initialization. Signed-off-by:
Sergey Dyasly <dserrg@gmail.com> Tested-by:
Sameer Nanda <snanda@chromium.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mandeep Singh Baines <msb@chromium.org> Cc: "Ma, Xindong" <xindong.ma@intel.com> Reviewed-by:
-
Oleg Nesterov authored
commit 1da4db0c upstream. Change oom_kill.c to use for_each_thread() rather than the racy while_each_thread() which can loop forever if we race with exit. Note also that most users were buggy even if while_each_thread() was fine, the task can exit even _before_ rcu_read_lock(). Fortunately the new for_each_thread() only requires the stable task_struct, so this change fixes both problems. Signed-off-by:
-
Oleg Nesterov authored
commit 0c740d0a upstream. while_each_thread() and next_thread() should die, almost every lockless usage is wrong. 1. Unless g == current, the lockless while_each_thread() is not safe. while_each_thread(g, t) can loop forever if g exits, next_thread() can't reach the unhashed thread in this case. Note that this can happen even if g is the group leader, it can exec. 2. Even if while_each_thread() itself was correct, people often use it wrongly. It was never safe to just take rcu_read_lock() and loop unless you verify that pid_alive(g) == T, even the first next_thread() can point to the already freed/reused memory. This patch adds signal_struct->thread_head and task->thread_node to create the normal rcu-safe list with the stable head. The new for_each_thread(g, t) helper is always safe under rcu_read_lock() as long as this task_struct can't go away. Note: of course it is ugly to have both task_struct->thread_node and the old task_struct->thread_group, we will kill it later, after we change the users of while_each_thread() to use for_each_thread(). Perhaps we can kill it even before we convert all users, we can reimplement next_thread(t) using the new thread_head/thread_node. But we can't do this right now because this will lead to subtle behavioural changes. For example, do/while_each_thread() always sees at least one task, while for_each_thread() can do nothing if the whole thread group has died. Or thread_group_empty(), currently its semantics is not clear unless thread_group_leader(p) and we need to audit the callers before we can change it. So this patch adds the new interface which has to coexist with the old one for some time, hopefully the next changes will be more or less straightforward and the old one will go away soon. Signed-off-by:
-
- 29 May, 2014 32 commits
-
-
Jiri Slaby authored
-
Eric Dumazet authored
[ Upstream commit e33d0ba8 ] Recycling skb always had been very tough... This time it appears GRO layer can accumulate skb->truesize adjustments made by drivers when they attach a fragment to skb. skb_gro_receive() can only subtract from skb->truesize the used part of a fragment. I spotted this problem seeing TcpExtPruneCalled and TcpExtTCPRcvCollapsed that were unexpected with a recent kernel, where TCP receive window should be sized properly to accept traffic coming from a driver not overshooting skb->truesize. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Li RongQing authored
[ Upstream commit fbdc0ad0 ] the value of itag is a random value from stack, and may not be initiated by fib_validate_source, which called fib_combine_itag if CONFIG_IP_ROUTE_CLASSID is not set This will make the cached dst uncertainty Signed-off-by:
Li RongQing <roy.qing.li@gmail.com> Acked-by:
Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
-
Steffen Klassert authored
[ Upstream commit 78ff4be4 ] We need to initialize the fallback device to have a correct mtu set on this device. Otherwise the mtu is set to null and the device is unusable. Fixes: fd58156e ("IPIP: Use ip-tunneling code.") Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Antonio Quartulli authored
[ Upstream commit 377fe0f9 ] A pointer to the orig_node representing a bat-gateway is stored in the gw_node->orig_node member, but the refcount for such orig_node is never increased. This leads to memory faults when gw_node->orig_node is accessed and the originator has already been freed. Fix this by increasing the refcount on gw_node creation and decreasing it on gw_node free. Signed-off-by:
Antonio Quartulli <antonio@open-mesh.com> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
-
Cong Wang authored
[ Upstream commit 200b916f ] From: Cong Wang <cwang@twopensource.com> commit 50624c93 (net: Delay default_device_exit_batch until no devices are unregistering) introduced rtnl_lock_unregistering() for default_device_exit_batch(). Same race could happen we when rmmod a driver which calls rtnl_link_unregister() as we call dev->destructor without rtnl lock. For long term, I think we should clean up the mess of netdev_run_todo() and net namespce exit code. Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Cong Wang <cwang@twopensource.com> Signed-off-by:
-
Susant Sahani authored
[ Upstream commit c8965932 ] The function ip6_tnl_validate assumes that the rtnl attribute IFLA_IPTUN_PROTO always be filled . If this attribute is not filled by the userspace application kernel get crashed with NULL pointer dereference. This patch fixes the potential kernel crash when IFLA_IPTUN_PROTO is missing . Signed-off-by:
Susant Sahani <susant@redhat.com> Acked-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 1c363900 ] If the sfc driver is in legacy interrupt mode (either explicitly by using interrupt_mode module param or by falling back to it) it will hit a warning at kernel/irq/manage.c because it will try to free an irq which wasn't allocated by it in the first place because the MSI(X) irqs are zero and it'll try to free them unconditionally. So fix it by checking if we're in legacy mode and freeing the appropriate irqs. CC: Zenghui Shi <zshi@redhat.com> CC: Ben Hutchings <ben@decadent.org.uk> CC: <linux-net-drivers@solarflare.com> CC: Shradha Shah <sshah@solarflare.com> CC: David S. Miller <davem@davemloft.net> Fixes: 1899c111 ("sfc: Fix IRQ cleanup in case of a probe failure") Reported-by:
Zenghui Shi <zshi@redhat.com> Signed-off-by:
Nikolay Aleksandrov <nikolay@redhat.com> Acked-by:
Shradha Shah <sshah@solarflare.com> Signed-off-by:
-
Peter Christensen authored
[ Upstream commit bbeb0ead ] Clearing the IFF_ALLMULTI flag on a down interface could cause an allmulti overflow on the underlying interface. Attempting the set IFF_ALLMULTI on the underlying interface would cause an error and the log message: "allmulti touches root, set allmulti failed." Signed-off-by:
Peter Christensen <pch@ordbogen.com> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit 6b5eeb7f ] This driver maps 802.1q VLANs to MBIM sessions. The mapping is based on a bogus assumption that all tagged frames will use the acceleration API because we enable NETIF_F_HW_VLAN_CTAG_TX. This fails for e.g. frames tagged in userspace using packet sockets. Such frames will erroneously be considered as untagged and silently dropped based on not being IP. Fix by falling back to looking into the ethernet header for a tag if no accelerated tag was found. Fixes: a82c7ce5 ("net: cdc_ncm: map MBIM IPS SessionID to VLAN ID") Cc: Greg Suarez <gsuarez@smithmicro.com> Signed-off-by:
-
Sergey Popovich authored
[ Upstream commit aeefa1ec ] Increment fib_info_cnt in fib_create_info() right after successfuly alllocating fib_info structure, overwise fib_metrics allocation failure leads to fib_info_cnt incorrectly decremented in free_fib_info(), called on error path from fib_create_info(). Signed-off-by:
-
Florian Westphal authored
[ Upstream commit 418a3156 ] If conntrack defragments incoming ipv6 frags it stores largest original frag size in ip6cb and sets ->local_df. We must thus first test the largest original frag size vs. mtu, and not vice versa. Without this patch PKTTOOBIG is still generated in ip6_fragment() later in the stack, but 1) IPSTATS_MIB_INTOOBIGERRORS won't increment 2) packet did (needlessly) traverse netfilter postrouting hook. Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path") Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Florian Westphal authored
[ Upstream commit ca6c5d4a ] local_df means 'ignore DF bit if set', so if its set we're allowed to perform ip fragmentation. This wasn't noticed earlier because the output path also drops such skbs (and emits needed icmp error) and because netfilter ip defrag did not set local_df until couple of days ago. Only difference is that DF-packets-larger-than MTU now discarded earlier (f.e. we avoid pointless netfilter postrouting trip). While at it, drop the repeated test ip_exceeds_mtu, checking it once is enough... Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path") Signed-off-by:
-
Ying Cai authored
[ Upstream commit e96f2e7c ] In ip_tunnel_rcv(), set skb->network_header to inner IP header before IP_ECN_decapsulate(). Without the fix, IP_ECN_decapsulate() takes outer IP header as inner IP header, possibly causing error messages or packet drops. Note that this skb_reset_network_header() call was in this spot when the original feature for checking consistency of ECN bits through tunnels was added in eccc1bb8 ("tunnel: drop packet if ECN present with not-ECT"). It was only removed from this spot in 3d7b46cd ("ip_tunnel: push generic protocol handling to ip_tunnel module."). Fixes: 3d7b46cd ("ip_tunnel: push generic protocol handling to ip_tunnel module.") Reported-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Ying Cai <ycai@google.com> Acked-by:
-
Andy King authored
[ Upstream commit 2c4a336e ] Right now the core vsock module is the owner of the proto family. This means there's nothing preventing the transport module from unloading if there are open sockets, which results in a panic. Fix that by allowing the transport to be the owner, which will refcount it properly. Includes version bump to 1.0.1.0-k Passes checkpatch this time, I swear... Acked-by:
Dmitry Torokhov <dtor@vmware.com> Signed-off-by:
Andy King <acking@vmware.com> Signed-off-by:
-
Liu Yu authored
[ Upstream commit 0cda345d ] commit b9f47a3a (tcp_cubic: limit delayed_ack ratio to prevent divide error) try to prevent divide error, but there is still a little chance that delayed_ack can reach zero. In case the param cnt get negative value, then ratio+cnt would overflow and may happen to be zero. As a result, min(ratio, ACK_RATIO_LIMIT) will calculate to be zero. In some old kernels, such as 2.6.32, there is a bug that would pass negative param, which then ultimately leads to this divide error. commit 5b35e1e6 (tcp: fix tcp_trim_head() to adjust segment count with skb MSS) fixed the negative param issue. However, it's safe that we fix the range of delayed_ack as well, to make sure we do not hit a divide by zero. CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
Liu Yu <allanyuliu@tencent.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit f114890c ] This reverts commit 12a2856b. The commit above doesn't appear to be necessary any more as the checksums appear to be correctly computed/validated. Additionally the above commit breaks kvm configurations where one VM is using a device that support checksum offload (virtio) and the other VM does not. In this case, packets leaving virtio device will have CHECKSUM_PARTIAL set. The packets is forwarded to a macvtap that has offload features turned off. Since we use CHECKSUM_UNNECESSARY, the host does does not update the checksum and thus a bad checksum is passed up to the guest. CC: Daniel Lezcano <daniel.lezcano@free.fr> CC: Patrick McHardy <kaber@trash.net> CC: Andrian Nord <nightnord@gmail.com> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Michael S. Tsirkin <mst@redhat.com> CC: Jason Wang <jasowang@redhat.com> Signed-off-by:
Vlad Yasevich <vyasevic@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Acked-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit cbdb0427 ] The following is a problematic configuration: VM1: virtio-net device connected to macvtap0@eth0 VM2: e1000 device connect to macvtap1@eth0 The problem is is that virtio-net supports checksum offloading and thus sends the packets to the host with CHECKSUM_PARTIAL set. On the other hand, e1000 does not support any acceleration. For small TCP packets (and this includes the 3-way handshake), e1000 ends up receiving packets that only have a partial checksum set. This causes TCP to fail checksum validation and to drop packets. As a result tcp connections can not be established. Commit 3e4f8b78 macvtap: Perform GSO on forwarding path. fixes this issue for large packets wthat will end up undergoing GSO. This commit adds a check for the non-GSO case and attempts to compute the checksum for partially checksummed packets in the non-GSO case. CC: Daniel Lezcano <daniel.lezcano@free.fr> CC: Patrick McHardy <kaber@trash.net> CC: Andrian Nord <nightnord@gmail.com> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Michael S. Tsirkin <mst@redhat.com> CC: Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Oliver Hartkopp authored
[ Upstream commit ddcde142 ] With commit cc9fa74e ("slip/slcan: added locking in wakeup function") a formerly missing locking was added to slip.c and slcan.c by Andre Naujoks. Alexander Stein contributed the fix 367525c8 ("can: slcan: Fix spinlock variant") as the kernel lock debugging advised to use spin_lock_bh() instead of just using spin_lock(). This fix has to be applied to the same code section in slip.c for the same reason too. Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit 6f10c5d1 ] Dan writes: "The Dell drivers use the same configuration for PIDs: 81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card 81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card 81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card 81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card 81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card These devices are all clearly Sierra devices, but are also definitely Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750. >From DellGobi5kSetup.exe from the Dell drivers: usbif0: serial/firmware loader? usbif2: nmea usbif3: modem/ppp usbif8: net/QMI" Reported-by:
-
Bjørn Mork authored
[ Upstream commit 41be7d90 ] A number of older CMOTech modems are based on Qualcomm chips and exporting a QMI/wwan function. Reported-by:
Lars Melin <larsm17@gmail.com> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit 75573660 ] Device interface layout: 0: ff/ff/ff - serial 1: ff/00/00 - serial AT+PPP 2: ff/ff/ff - QMI/wwan 3: 08/06/50 - storage Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit efc0b25c ] Device interface layout: 0: ff/ff/ff - serial 1: ff/ff/ff - serial AT+PPP 2: 08/06/50 - storage 3: ff/ff/ff - serial 4: ff/ff/ff - QMI/wwan Reported-by:
Julio Araujo <julio.araujo@wllctel.com.br> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit 9214224e ] Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit 1c138607 ] Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit b85f5dea ] Signed-off-by:
-
Xufeng Zhang authored
[ Upstream commit 85350871 ] commit 813b3b5d (ipv4: Use caller's on-stack flowi as-is in output route lookups.) introduces another regression which is very similar to the problem of commit e6b45241 (ipv4: reset flowi parameters on route connect) wants to fix: Before we call ip_route_output_key() in sctp_v4_get_dst() to get a dst that matches a bind address as the source address, we have already called this function previously and the flowi parameters have been initialized including flowi4_oif, so when we call this function again, the process in __ip_route_output_key() will be different because of the setting of flowi4_oif, and we'll get a networking device which corresponds to the inputted flowi4_oif as the output device, this is wrong because we'll never hit this place if the previously returned source address of dst match one of the bound addresses. To reproduce this problem, a vlan setting is enough: # ifconfig eth0 up # route del default # vconfig add eth0 2 # vconfig add eth0 3 # ifconfig eth0.2 10.0.1.14 netmask 255.255.255.0 # route add default gw 10.0.1.254 dev eth0.2 # ifconfig eth0.3 10.0.0.14 netmask 255.255.255.0 # ip rule add from 10.0.0.14 table 4 # ip route add table 4 default via 10.0.0.254 src 10.0.0.14 dev eth0.3 # sctp_darn -H 10.0.0.14 -P 36422 -h 10.1.4.134 -p 36422 -s -I You'll detect that all the flow are routed to eth0.2(10.0.1.254). Signed-off-by:
Xufeng Zhang <xufeng.zhang@windriver.com> Signed-off-by:
Julian Anastasov <ja@ssi.bg> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Toshiaki Makita authored
[ Upstream commit 30313a3d ] When bridge device is created with IFLA_ADDRESS, we are not calling br_stp_change_bridge_id(), which leads to incorrect local fdb management and bridge id calculation, and prevents us from receiving frames on the bridge device. Reported-by:
Tom Gundersen <teg@jklm.no> Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by:
-
Kumar Sundararajan authored
[ Upstream commit 1c265854 ] When the ipv6 fib changes during a table dump, the walk is restarted and the number of nodes dumped are skipped. But the existing code doesn't advance to the next node after a node is skipped. This can cause the dump to loop or produce lots of duplicates when the fib is modified during the dump. This change advances the walk to the next node if the current node is skipped after a restart. Signed-off-by:
Kumar Sundararajan <kumar@fb.com> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
David Gibson authored
[ Upstream commit c53864fd ] Since 115c9b81 (rtnetlink: Fix problem with buffer allocation), RTM_NEWLINK messages only contain the IFLA_VFINFO_LIST attribute if they were solicited by a GETLINK message containing an IFLA_EXT_MASK attribute with the RTEXT_FILTER_VF flag. That was done because some user programs broke when they received more data than expected - because IFLA_VFINFO_LIST contains information for each VF it can become large if there are many VFs. However, the IFLA_VF_PORTS attribute, supplied for devices which implement ndo_get_vf_port (currently the 'enic' driver only), has the same problem. It supplies per-VF information and can therefore become large, but it is not currently conditional on the IFLA_EXT_MASK value. Worse, it interacts badly with the existing EXT_MASK handling. When IFLA_EXT_MASK is not supplied, the buffer for netlink replies is fixed at NLMSG_GOODSIZE. If the information for IFLA_VF_PORTS exceeds this, then rtnl_fill_ifinfo() returns -EMSGSIZE on the first message in a packet. netlink_dump() will misinterpret this as having finished the listing and omit data for this interface and all subsequent ones. That can cause getifaddrs(3) to enter an infinite loop. This patch addresses the problem by only supplying IFLA_VF_PORTS when IFLA_EXT_MASK is supplied with the RTEXT_FILTER_VF flag set. Signed-off-by:
David Gibson <david@gibson.dropbear.id.au> Reviewed-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
David Gibson authored
[ Upstream commit 973462bb ] Without IFLA_EXT_MASK specified, the information reported for a single interface in response to RTM_GETLINK is expected to fit within a netlink packet of NLMSG_GOODSIZE. If it doesn't, however, things will go badly wrong, When listing all interfaces, netlink_dump() will incorrectly treat -EMSGSIZE on the first message in a packet as the end of the listing and omit information for that interface and all subsequent ones. This can cause getifaddrs(3) to enter an infinite loop. This patch won't fix the problem, but it will WARN_ON() making it easier to track down what's going wrong. Signed-off-by:
Jiri Pirko <jpirko@redhat.com> Signed-off-by:
-
Andrew Lutomirski authored
[ Upstream commit 78541c1d ] The caller needs capabilities on the namespace being queried, not on their own namespace. This is a security bug, although it likely has only a minor impact. Cc: stable@vger.kernel.org Signed-off-by:
Andy Lutomirski <luto@amacapital.net> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
