- 07 Jan, 2009 40 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (171 commits) Blackfin arch: fix bug - BF527 0.2 silicon has different CPUID (DSPID) value Blackfin arch: Enlarge flash partition for kenel for bf533/bf537 boards Blackfin arch: fix bug: kernel crash when enable SDIO host driver Blackfin arch: Print FP at level KERN_NOTICE Blackfin arch: drop ad73311 test code Blackfin arch: update board default configs Blackfin arch: Set PB4 as the default irq for bf548 board v1.4+. Blackfin arch: fix typo in early printk bit size processing Blackfin arch: enable reprogram cclk and sclk for bf518f-ezbrd Blackfin arch: add SDIO host driver platform data Blackfin arch: fix bug - kernel stops at initial console Blackfin arch: fix bug - kernel crash after config IP for ethernet port Blackfin arch: add sdh support for bf518f-ezbrd Blackfin arch: fix bug - kernel detects BF532 incorrectly Blackfin arch: add () to avoid warnings from gcc Blackfin arch: change HWTRACE Kconfig and set it on default Blackfin arch: Clean oprofile build path for blackfin Blackfin arch: remove hardware PM code, oprofile not use it Blackfin arch: rewrite get_sclk()/get_vco() Blackfin arch: cleanup and unify the ins functions ...
-
git://jdelvare.pck.nerim.net/jdelvare-2.6Linus Torvalds authored
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (29 commits) hwmon: Fix various typos hwmon: Check for ACPI resource conflicts hwmon: (lm70) Add TI TMP121 support hwmon: (lm70) Code streamlining and cleanup hwmon: Deprecate the fscher and fscpos drivers hwmon: (fschmd) Add watchdog support hwmon: (fschmd) Cleanups for watchdog support hwmon: (i5k_amb) Load automatically on all 5000/5400 chipsets hwmon: (it87) Add support for the ITE IT8720F hwmon: Don't overuse I2C_CLIENT_MODULE_PARM hwmon: Add LTC4245 driver hwmon: (f71882fg) Fix fan_to/from_reg prototypes hwmon: (f71882fg) Printout fan modes hwmon: (f71882fg) Add documentation hwmon: (f71882fg) Fix auto_channels_temp temp numbering with f8000 hwmon: (f71882fg) Add missing pwm3 attr for f71862fg hwmon: (f71882fg) Add F8000 support hwmon: (f71882fg) Remove the fan_mode module option hwmon: (f71882fg) Separate max and crit alarm and beep hwmon: (f71882fg) Check for hwmon powerdown state ...
-
git://jdelvare.pck.nerim.net/jdelvare-2.6Linus Torvalds authored
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: i2c: Use snprintf to set adapter names Input: apanel - convert to new i2c binding i2c: Drop I2C_CLASS_CAM_DIGITAL i2c: Drop I2C_CLASS_CAM_ANALOG and I2C_CLASS_SOUND i2c: Drop I2C_CLASS_ALL i2c: Get rid of remaining bus_id access i2c: Replace bus_id with dev_name(), dev_set_name()
-
git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: avr32: Move syscalls.h under arch/avr32/include/asm/ avr32: Define DIE_OOPS avr32: Remove DMATEST from defconfigs arch/avr32: Eliminate NULL test and memset after alloc_bootmem avr32: data param to at32_add_device_mci() must be non-NULL atmel-mci: move atmel-mci.h file to include/linux avr32: Hammerhead board support avr32: Allow reserving multiple pins at once favr-32: Remove deprecated call MIMC200: Remove deprecated call avr: struct device - replace bus_id with dev_name(), dev_set_name() avr32: Introducing asm/syscalls.h
-
git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixesLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes: GFS2: Fix typo in gfs_page_mkwrite() GFS2: LSF and LBD are now one and the same GFS2: Set GFP_NOFS when allocating page on write
-
git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6: xtensa: Update platform files to reflect new location of the header files. xtensa: switch to packed struct unaligned access implementation xtensa: Add xt2000 support files. xtensa: move headers files to arch/xtensa/include xtensa: use the new byteorder headers
-
Heiko Carstens authored
disable_nonboot_cpus calls _cpu_down. But _cpu_down requires that the caller already created the stop_machine workqueue (like cpu_down does). Otherwise a call to stop_machine will lead to accesses to random memory regions. When introducing this new interface (9ea09af3 "stop_machine: introduce stop_machine_create/destroy") I missed the second call site of _cpu_down. So add the missing stop_machine_create/destroy calls to disable_nonboot_cpus as well. Fixes suspend-to-ram/disk and also this bug: [ 286.547348] BUG: unable to handle kernel paging request at 6b6b6b6b [ 286.548940] IP: [<c0150ca4>] __stop_machine+0x88/0xe3 [ 286.550598] Oops: 0002 [#1] SMP [ 286.560580] Pid: 3273, comm: halt Not tainted (2.6.28-06127-g238c6d54 [ 286.560580] EIP: is at __stop_machine+0x88/0xe3 [ 286.560580] Process halt (pid: 3273, ti=f1a28000 task=f4530f30 [ 286.560580] Call Trace: [ 286.560580] [<c03d04e4>] ? _cpu_down+0x10f/0x234 [ 286.560580] [<c012a57e>] ? disable_nonboot_cpus+0x58/0xdc [ 286.560580] [<c01360c0>] ? kernel_poweroff+0x22/0x39 [ 286.560580] [<c0136301>] ? sys_reboot+0xde/0x14c [ 286.560580] [<c01331b2>] ? complete_signal+0x179/0x191 [ 286.560580] [<c0133396>] ? send_signal+0x1cc/0x1e1 [ 286.560580] [<c03de418>] ? _spin_unlock_irqrestore+0x2d/0x3c [ 286.560580] [<c0133b65>] ? group_send_signal_info+0x58/0x61 [ 286.560580] [<c0133b9e>] ? kill_pid_info+0x30/0x3a [ 286.560580] [<c0133d49>] ? sys_kill+0x75/0x13a [ 286.560580] [<c01a06cb>] ? mntput_no_expire+ox1f/0x101 [ 286.560580] [<c019b3b3>] ? dput+0x1e/0x105 [ 286.560580] [<c018ef87>] ? __fput+0x150/0x158 [ 286.560580] [<c0157abf>] ? audit_syscall_entry+0x137/0x159 [ 286.560580] [<c010329f>] ? sysenter_do_call+0x12/0x34 Reported-and-tested-by:
"Justin P. Mattock" <justinmattock@gmail.com> Reviewed-by:
Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Tested-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Alan Cox authored
Missing an include and thus breaks the x86-64 build. Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivialLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits) trivial: chack -> check typo fix in main Makefile trivial: Add a space (and a comma) to a printk in 8250 driver trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx trivial: Fix misspelling of "firmware" in powerpc Makefile trivial: Fix misspelling of "firmware" in usb.c trivial: Fix misspelling of "firmware" in qla1280.c trivial: Fix misspelling of "firmware" in a100u2w.c trivial: Fix misspelling of "firmware" in megaraid.c trivial: Fix misspelling of "firmware" in ql4_mbx.c trivial: Fix misspelling of "firmware" in acpi_memhotplug.c trivial: Fix misspelling of "firmware" in ipw2100.c trivial: Fix misspelling of "firmware" in atmel.c trivial: Fix misspelled firmware in Kconfig trivial: fix an -> a typos in documentation and comments trivial: fix then -> than typos in comments and documentation trivial: update Jesper Juhl CREDITS entry with new email trivial: fix singal -> signal typo trivial: Fix incorrect use of "loose" in event.c trivial: printk: fix indentation of new_text_line declaration trivial: rtc-stk17ta8: fix sparse warning ...
-
Jiri Kosina authored
Commit 07903407 ("HID: hiddev cleanup -- handle all error conditions properly") by mistake removed proper initialization of hid->hiddev pointer in hiddev_connect() in case usb_register_dev() succeeds for the hiddev node. Put it properly back in place. Reported-and-tested-by:
Gabriel C <nix.or.die@googlemail.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Detlef Riekenberg authored
The typedefs for __u64 and __s64 where fixed to be available for other compiler on May 2 2008 by H. Peter Anvin (in commit edfa5cfa) Acked-by:
H. Peter Anvin <hpa@zytor.com> Signed-off-by:
Detlef Riekenberg <wine.dev@web.de> Signed-off-by:
-
Jean Delvare authored
Signed-off-by:
Jean Delvare <khali@linux-fr.org> Acked-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
David Hubbard <david.c.hubbard@gmail.com>
-
Jean Delvare authored
Check for ACPI resource conflicts in hwmon drivers. I've included all Super-I/O and PCI drivers. I've voluntarily left out: * Vendor-specific drivers: if they conflicted on any system, this would pretty much mean that they conflict on all systems, and we would know by now. * Legacy ISA drivers (lm78 and w83781d): they only support chips found on old designs were ACPI either wasn't supported or didn't deal with thermal management. * Drivers accessing the I/O resources indirectly (e.g. through SMBus): the checks are already done where they belong, i.e. in the bus drivers. Signed-off-by:
Jean Delvare <jdelvare@suse.de> Acked-by:
-
Manuel Lauss authored
The Texas Instruments TMP121 is a SPI temperature sensor very similar to the LM70, with slightly higher resolution. This patch extends the LM70 driver to support the TMP121. The TMP123 differs in pin assign- ment. Signed-off-by:
Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by:
-
Kaiwan N Billimoria authored
This fixes a byteswap bug in the LM70 temperature sensor driver, which was previously covered up by a converse bug in the driver for the LM70EVAL-LLP board (which is also fixed). Other fixes: doc updates, remove an annoying msleep(), and improve three-wire protocol handling. Signed-off-by:
Kaiwan N Billimoria <kaiwan@designergraphix.com> [ dbrownell@users.sourceforge.net: doc and whitespace tweaks ] Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Hans de Goede authored
Now that the new merged fschmd driver has gained support for the watchdog integrated into these IC's, there is no more reason to keep the old fscher and fscpos drivers around, so mark them as deprecated. Signed-off-by:
-
Hans de Goede authored
This patch adds support for the watchdog part found in _all_ supported FSC sensor chips. Signed-off-by:
-
Hans de Goede authored
Various small cleanups in preparation of adding watchdog support, mostly removing _MASK postfix from defines which are not masks. Signed-off-by:
-
Darrick J. Wong authored
It turns out that we cannot create a pci_driver in this driver because PCI will not call this module's probe function if the i5000-edac driver is already loaded. That said, we only want one value (AMBASE) from the PCI config space. Neither driver alters this value, so it's safe to read it. However, we still want the module aliases, so provide that. Signed-off-by:
Darrick J. Wong <djwong@us.ibm.com> Signed-off-by:
-
Jean-Marc Spaggiari authored
Allow it87.c to handle IT8720 chipset like IT8718 in order to retrieve voltage, temperatures and fans speed from sensors tools. Also updating the related documentation. Signed-off-by:
Jean-Marc Spaggiari <jean-marc@spaggiari.org> Signed-off-by:
-
Jean Delvare authored
I2C_CLIENT_MODULE_PARM is overkill for force_subclients. We really only use 4 out of the 48 slots, so we're better defining a custom variable instead. This change saves 92 bytes of data for each of the five drivers affected. Signed-off-by:
Marc Hulsman <m.hulsman@tudelft.nl> Cc: Mark M. Hoffman <mhoffman@lightlink.com>
-
Ira Snyder authored
Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot Swap controller I2C monitoring interface. Signed-off-by:
Ira W. Snyder <iws@ovro.caltech.edu> Acked-by:
-
Hans de Goede authored
The RPM after conversion from / before conversion to a register value can be much more than 65535 (up to 1500000), so putting this into an u16 can cause overflows. This changes the functions to use an int to store / get RPM instead. Signed-off-by:
-
Hans de Goede authored
Print the mode (duty-cycle or RPM) of each fan on driver load. Signed-off-by:
-
Hans de Goede authored
Add some documentation about the f71882fg driver, and update the Kconfig documentation to report the new supported models. Signed-off-by:
-
Hans de Goede authored
Adjust auto_channels_temp show and store functions for different numbering of temps between f8000 and other supported models. Signed-off-by:
-
Hans de Goede authored
For some reason the fan_attr array for the f71862fg was missing the attr for the 3th pwm output. This patch fixes this. Signed-off-by:
-
Hans de Goede authored
And (finally) the patch actually adding f8000 support. Signed-off-by:
-
Hans de Goede authored
Remove the fan_mode module option it was a monstrosity to begin with, and when adding support for the F8000 it becomes a real pain! Signed-off-by:
-
Hans de Goede authored
While studying the datasheets for adding F8000 support, I noticed that the F718x2 has separate alarms (and beep control) for its max and crit limits. We keep the temp#_alarm attributes as they are, even though it would be more logical to rename them to temp#_max_alarm. Because lm_sensors v2 depends on them. Signed-off-by:
-
Hans de Goede authored
More F8000 prep work. Take over the checking if the hwmon part is not powered down from the standalone f8000 driver. This check is valid for all supported models. Signed-off-by:
-
Hans de Goede authored
Simplify fan and temp hyst. handling by treating the registers as an array of nibbles instead of using switch cases. Also unify the way hysts are handled between temp and fans, the temp code was storing the actual per temp hyst values in 4 u8's, where as the fan code was storing actual register values. Signed-off-by:
-
Hans de Goede authored
While working on adding F8000 support I noticed that various of the store sysfs functions (and a few of the show also) had issues. This patch fixes the following issues in these functions: * store: storing the result of strto[u]l in an int, resulting in a possible overflow before boundary checking * store: use of f71882fg_update_device(), we don't want to read the whole device in store functions, just the registers we need * store: use of cached register values instead of reading the needed regs in the store function, including cases where f71882fg_update_device() was not used, this could cause real isues * show: shown value is a calculation of 2 or more cached register reads, without locking the data struct. Signed-off-by:
-
Hans de Goede authored
This patch is a preparation patch for adding F8000 support to the f71882fg driver. If you look at the register addresses and esp, the bits used for the temperature channels, then you will notice that it appears that they start at 1 in a system meant to start at 0. As the F8000 actually uses the 0 addresses and bits, this patch changes the f71882fg driver to take 4 temperatures numbered 0-3 in to account, using 1-3 in this new scheme for the temperatures actually present in the F718x2FG. Signed-off-by:
-
Hans de Goede authored
The f71882fg driver did some io to ioports it hadn't reserved yet in its find (detect) function, this patches moves this io to the probe function where these ports are reserved and this io belongs. Signed-off-by:
-
Hans de Goede authored
This patch adds support for the Fintek f71862fg superio monitoring functions to the f71882fg driver. This support has been tested without problems on a Jetway J9F2 by Tony McConnell. Signed-off-by:
-
Hans de Goede authored
Various small cleanups as preparation for adding f71862fg support to the f71882fg driver. Signed-off-by:
-
Mark van Doesburg authored
Add PWM (fan speed control) support to the f71882fg driver. Both manual control and automatic (temperature-based) modes are supported. Additionally, each mode has a PWM-based and an RPM-based variant. By default we use the mode set by the BIOS. Signed-off-by:
-
Mark van Doesburg authored
A few cleanups that were originally part of a larger patch but are better submitted separately. Signed-off-by:
-
Mark van Doesburg authored
Convert f71882fg driver from SENSOR_ATTR to SENSOR_ATTR2 use, this is a preparation patch for adding pwm support, which is broken out to make what changes really in the pwm support patch clear. Signed-off-by:
-
