Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joe reported to me that right after a bring up of a r6040 interface
the ethtool output had no consistent output with respect to link duplex
and speed. Fix this by adding a missing phy_start call in r6040_up and
conversely a phy_stop call in r6040_down to properly initialize phy states.
Reported-by: Joe Chou <Joe.Chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Query port will now identify a 40G Ethernet speed.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Netdevice was being freed without being unregistered first if
mlx4_SET_PORT_general or mlx4_INIT_PORT failed.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Number of bits taken from mac table index in QP
calculation should be based on log_num_mac parameter.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed a memory leak caused by missing iounmap when device
is being released.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Sharon Cohen <sharonc@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moderation is now done per ring and coalescing is enabled
by set_ring_param in ethtool.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed a bug where ring size change caused insufficient memory
upon driver restart due to unreleased EQs.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now only RX rings used irq per ring
and TX used only one per port.
>From now on, both of them will use the
irq per ring while RX & TX ring[i] will
use the same irq.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Sharon Cohen <sharonc@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for reporting ring sizes via ethtool -g to the 8139cp driver.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/batman-adv/soft-interface.c

There's no point in open-coding sock_valbool_flag().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change will combine the writes of tx_buffer_info and the Tx data
descriptors into a single function. The advantage of this is that we can
avoid needless memory reads from the buffer info struct and speed things up
by keeping the accesses to the local registers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to combine all of the TX flags fields into one u32
flags field so that it can be stored into the tx_buffer_info structure.
This includes the time stamp flag as well as mapped_as_page flag info.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to cleanup the protocol handling in the transmit path
so that it correctly offloads software VLAN tagged frames.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to improve the readability of the driver by separating
out the cmd_type configuration and the olinfo configuration into their own
functions.  By doing this it is much easier to determine which ingredients
go into setting up these to portions of the descriptor.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change converts two tx_buffer_info index values into pointers.  The
advantage to this is that we reduce unnecessary computations and in the case
of next_to_watch we get an added bonus of the value being able to provide
additional information as a NULL value indicates it is unset versus a 0 not
having any meaning for the index value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to simplify the transmit path by reducing the overhead
for creating a transmit context descriptor.  The current implementation is
split with igb_tso and igb_tx_csum doing two separate implementations on
how to setup the tx_buffer_info structure and the tx_desc.  By combining
them it is possible to reduce code and simplify things since now only one
function will create context descriptors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to be able to improve the performance of the TX path it has been
necessary to add addition info to the tx_buffer_info structure.  However a
side effect is that the structure has gotten larger and this in turn has
also increased the size of the RX buffer info structure.  In order to avoid
this in the future I am splitting the single buffer_info structure into two
separate ones and instead I will join them by making the buffer_info
pointer in the ring a union of the two.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is to make the NAPI budget limits for transmit
adjustable.  Currently they are only set to 128, and when
the changes/improvements to NAPI occur to allow for adjustability,
it would be possible to tune the value for optimal
performance with applications such as routing.

v2: remove tie between NAPI and interrupt moderation
    fix work limit define name (s/IXGBE/IGB/)
    Update patch description to better reflect patch
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>

When short packets are received with jumbos enabled on 82579, they can be
interpreted to have a receive address that does not match any configured
address.  This is due to a hardware bug that can be worked around by
reducing the number of IPG octets added when the packet is transferred from
the PHY to the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The e1000 driver when running with lockdep could run into
some possible deadlocks between the work items acquiring
rtnl and the rtnl lock being acquired before work items
were cancelled.

Use a private mutex to make sure lock ordering isn't violated.
The private mutex is only used to protect areas not generally
covered by the rtnl lock already.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

With the previous commit, there are several functions
that are only ever called from thread context, and are
able to sleep with msleep instead of mdelay.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Thomas Gleixner (tglx) reported that e1000 was delaying for many milliseconds
(using mdelay) from inside timer/interrupt context.  None of these paths are
performance critical and can be moved into threads/work items.  This patch
implements the work items and the next patch changes the mdelays to msleeps.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump the version string to better match pair up with the out of tree
driver that contains the same functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

* git://github.com/davem330/net:
  net: fix typos in Documentation/networking/scaling.txt
  bridge: leave carrier on for empty bridge
  netfilter: Use proper rwlock init function
  tcp: properly update lost_cnt_hint during shifting
  tcp: properly handle md5sig_pool references
  macvlan/macvtap: Fix unicast between macvtap interfaces in bridge mode

In summary, this DMI quirk uses the _CRS info by default for the ASUS
M2V-MX SE by turning on `pci=use_crs` and is similar to the quirk
added by commit 2491762c ("x86/PCI: use host bridge _CRS info on
ASRock ALiveSATA2-GLAN") whose commit message should be read for further
information.

Since commit 3e3da00c ("x86/pci: AMD one chain system to use pci
read out res") Linux gives the following oops:

    parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
    HDA Intel 0000:20:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    HDA Intel 0000:20:01.0: setting latency timer to 64
    BUG: unable to handle kernel paging request at ffffc90011c08000
    IP: [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
    PGD 13781a067 PUD 13781b067 PMD 1300ba067 PTE 800000fd00000173
    Oops: 0009 [#1] SMP
    last sysfs file: /sys/module/snd_pcm/initstate
    CPU 0
    Modules linked in: snd_hda_intel(+) snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event tpm_tis tpm snd_seq tpm_bios psmouse parport_pc snd_timer snd_seq_device parport processor evdev snd i2c_viapro thermal_sys amd64_edac_mod k8temp i2c_core soundcore shpchp pcspkr serio_raw asus_atk0110 pci_hotplug edac_core button snd_page_alloc edac_mce_amd ext3 jbd mbcache sha256_generic cryptd aes_x86_64 aes_generic cbc dm_crypt dm_mod raid1 md_mod usbhid hid sg sd_mod crc_t10dif sr_mod cdrom ata_generic uhci_hcd sata_via pata_via libata ehci_hcd usbcore scsi_mod via_rhine mii nls_base [last unloaded: scsi_wait_scan]
    Pid: 1153, comm: work_for_cpu Not tainted 2.6.37-1-amd64 #1 M2V-MX SE/System Product Name
    RIP: 0010:[<ffffffffa0578402>]  [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
    RSP: 0018:ffff88013153fe50  EFLAGS: 00010286
    RAX: ffffc90011c08000 RBX: ffff88013029ec00 RCX: 0000000000000006
    RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246
    RBP: ffff88013341d000 R08: 0000000000000000 R09: 0000000000000040
    R10: 0000000000000286 R11: 0000000000003731 R12: ffff88013029c400
    R13: 0000000000000000 R14: 0000000000000000 R15: ffff88013341d090
    FS:  0000000000000000(0000) GS:ffff8800bfc00000(0000) knlGS:00000000f7610ab0
    CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
    CR2: ffffc90011c08000 CR3: 0000000132f57000 CR4: 00000000000006f0
    DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
    DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
    Process work_for_cpu (pid: 1153, threadinfo ffff88013153e000, task ffff8801303c86c0)
    Stack:
     0000000000000005 ffffffff8123ad65 00000000000136c0 ffff88013029c400
     ffff8801303c8998 ffff88013341d000 ffff88013341d090 ffff8801322d9dc8
     ffff88013341d208 0000000000000000 0000000000000000 ffffffff811ad232
    Call Trace:
     [<ffffffff8123ad65>] ? __pm_runtime_set_status+0x162/0x186
     [<ffffffff811ad232>] ? local_pci_probe+0x49/0x92
     [<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b
     [<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b
     [<ffffffff8105afd0>] ? do_work_for_cpu+0xb/0x1b
     [<ffffffff8105fd3f>] ? kthread+0x7a/0x82
     [<ffffffff8100a824>] ? kernel_thread_helper+0x4/0x10
     [<ffffffff8105fcc5>] ? kthread+0x0/0x82
     [<ffffffff8100a820>] ? kernel_thread_helper+0x0/0x10
    Code: f4 01 00 00 ef 31 f6 48 89 df e8 29 dd ff ff 85 c0 0f 88 2b 03 00 00 48 89 ef e8 b4 39 c3 e0 8b 7b 40 e8 fc 9d b1 e0 48 8b 43 38 <66> 8b 10 66 89 14 24 8b 43 14 83 e8 03 83 f8 01 77 32 31 d2 be
    RIP  [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
     RSP <ffff88013153fe50>
    CR2: ffffc90011c08000
    ---[ end trace 8d1f3ebc136437fd ]---

Trusting the ACPI _CRS information (`pci=use_crs`) fixes this problem.

    $ dmesg | grep -i crs # with the quirk
    PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug

The match has to be against the DMI board entries though since the vendor entries are not populated.

    DMI: System manufacturer System Product Name/M2V-MX SE, BIOS 0304    10/30/2007

This quirk should be removed when `pci=use_crs` is enabled for machines
from 2006 or earlier or some other solution is implemented.

Using coreboot [1] with this board the problem does not exist but this
quirk also does not affect it either. To be safe though the check is
tightened to only take effect when the BIOS from American Megatrends is
used.

        15:13 < ruik> but coreboot does not need that
        15:13 < ruik> because i have there only one root bus
        15:13 < ruik> the audio is behind a bridge

        $ sudo dmidecode
        BIOS Information
                Vendor: American Megatrends Inc.
                Version: 0304
                Release Date: 10/30/2007

[1] http://www.coreboot.org/

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=30552

Cc: stable@kernel.org (2.6.34)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The second hunk fixes rps_sock_flow_table but has to re-wrap the paragraph.
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To avoid ifdefs in the other code that supports DCB notifiers
add stub routines. This method seems popular in other net code
for example 8021Q.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add DCBX mode to event notifiers so listeners can learn
currently enabled mode.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ifindex instead of ifname in the DCB app ring. This makes for a smaller
data structure and faster comparisons. It also avoids possible issues when
a net device is renamed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch verifies that the length of a buffer stored in a linked list
of pages is small enough to fit into a skb.

If the size is larger than a max size of a skb, it means that we shouldn't
go ahead building skbs anyway since we won't be able to send the buffer as
the user requested.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Cc: kvm@vger.kernel.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is based on an earlier patch by Nick Carter with comments
by David Lamparter but with some refinements. Thanks for their patience
this is a confusing area with overlap of standards, user requirements,
and compatibility with earlier releases.

It adds a new sysfs attribute
   /sys/class/net/brX/bridge/group_fwd_mask
that controls forwarding of frames with address of: 01-80-C2-00-00-0X
The default setting has no forwarding to retain compatibility.

One change from earlier releases is that forwarding of group
addresses is not dependent on STP being enabled or disabled. This
choice was made based on interpretation of tie 802.1 standards.
I expect complaints will arise because of this, but better to follow
the standard than continue acting incorrectly by default.

The filtering mask is writeable, but only values that don't forward
known control frames are allowed. It intentionally blocks attempts
to filter control protocols. For example: writing a 8 allows
forwarding 802.1X PAE addresses which is the most common request.
Reported-by: David Lamparter <equinox@diac24.net>
Original-patch-by: Nick Carter <ncarter100@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This resolves a regression seen by some users of bridging.
Some users use the bridge like a dummy device.
They expect to be able to put an IPv6 address on the device
with no ports attached. Although there are better ways of doing
this, there is no reason to not allow it.

Note: the bridge still will reflect the state of ports in the
bridge if there are any added.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of http://people.redhat.com/agk/git/linux-dm:
  dm crypt: always disable discard_zeroes_data
  dm: raid fix write_mostly arg validation
  dm table: avoid crash if integrity profile changes
  dm: flakey fix corrupt_bio_byte error path

* 'for-linus' of git://neil.brown.name/md:
  md: Avoid waking up a thread after it has been freed.

Only function 1 has support for Alternate MAC Address in the EEPROM before,
this update now allow function 2 and 3 to have support for Alternate MAC
Address in the EEPROM.
Signed-off-by: "Akeem G. Abodunrin" <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown  <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>