- 10 Mar, 2016 17 commits
-
-
Rainer Weikusat authored
[ Upstream commit a5527dda ] The unix_dgram_sendmsg routine use the following test if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) { to determine if sk and other are in an n:1 association (either established via connect or by using sendto to send messages to an unrelated socket identified by address). This isn't correct as the specified address could have been bound to the sending socket itself or because this socket could have been connected to itself by the time of the unix_peer_get but disconnected before the unix_state_lock(other). In both cases, the if-block would be entered despite other == sk which might either block the sender unintentionally or lead to trying to unlock the same spin lock twice for a non-blocking send. Add a other != sk check to guard against this. Fixes: 7d267278 ("unix: avoid use-after-free in ep_remove_wait_queue") Reported-By:
Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Tested-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Eric Dumazet authored
[ Upstream commit 91948309 ] Dmitry reported memory leaks of IP options allocated in ip_cmsg_send() when/if this function returns an error. Callers are responsible for the freeing. Many thanks to Dmitry for the report and diagnostic. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Jay Vosburgh authored
[ Upstream commit 21a75f09 ] The current logic in bond_arp_rcv will accept an incoming ARP for validation if (a) the receiving slave is either "active" (which includes the currently active slave, or the current ARP slave) or, (b) there is a currently active slave, and it has received an ARP since it became active. For case (b), the receiving slave isn't the currently active slave, and is receiving the original broadcast ARP request, not an ARP reply from the target. This logic can fail if there is no currently active slave. In this situation, the ARP probe logic cycles through all slaves, assigning each in turn as the "current_arp_slave" for one arp_interval, then setting that one as "active," and sending an ARP probe from that slave. The current logic expects the ARP reply to arrive on the sending current_arp_slave, however, due to switch FDB updating delays, the reply may be directed to another slave. This can arise if the bonding slaves and switch are working, but the ARP target is not responding. When the ARP target recovers, a condition may result wherein the ARP target host replies faster than the switch can update its forwarding table, causing each ARP reply to be sent to the previous current_arp_slave. This will never pass the logic in bond_arp_rcv, as neither of the above conditions (a) or (b) are met. Some experimentation on a LAN shows ARP reply round trips in the 200 usec range, but my available switches never update their FDB in less than 4000 usec. This patch changes the logic in bond_arp_rcv to additionally accept an ARP reply for validation on any slave if there is a current ARP slave and it sent an ARP probe during the previous arp_interval. Fixes: aeea64ac ("bonding: don't trust arp requests unless active slave really works") Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit a1b14d27 ] When ctx access is used, the kernel often needs to expand/rewrite instructions, so after that patching, branch offsets have to be adjusted for both forward and backward jumps in the new eBPF program, but for backward jumps it fails to account the delta. Meaning, for example, if the expansion happens exactly on the insn that sits at the jump target, it doesn't fix up the back jump offset. Analysis on what the check in adjust_branches() is currently doing: /* adjust offset of jmps if necessary */ if (i < pos && i + insn->off + 1 > pos) insn->off += delta; else if (i > pos && i + insn->off + 1 < pos) insn->off -= delta; First condition (forward jumps): Before: After: insns[0] insns[0] insns[1] <--- i/insn insns[1] <--- i/insn insns[2] <--- pos insns[P] <--- pos insns[3] insns[P] `------| delta insns[4] <--- target_X insns[P] `-----| insns[5] insns[3] insns[4] <--- target_X insns[5] First case is if we cross pos-boundary and the jump instruction was before pos. This is handeled correctly. I.e. if i == pos, then this would mean our jump that we currently check was the patchlet itself that we just injected. Since such patchlets are self-contained and have no awareness of any insns before or after the patched one, the delta is correctly not adjusted. Also, for the second condition in case of i + insn->off + 1 == pos, means we jump to that newly patched instruction, so no offset adjustment are needed. That part is correct. Second condition (backward jumps): Before: After: insns[0] insns[0] insns[1] <--- target_X insns[1] <--- target_X insns[2] <--- pos <-- target_Y insns[P] <--- pos <-- target_Y insns[3] insns[P] `------| delta insns[4] <--- i/insn insns[P] `-----| insns[5] insns[3] insns[4] <--- i/insn insns[5] Second interesting case is where we cross pos-boundary and the jump instruction was after pos. Backward jump with i == pos would be impossible and pose a bug somewhere in the patchlet, so the first condition checking i > pos is okay only by itself. However, i + insn->off + 1 < pos does not always work as intended to trigger the adjustment. It works when jump targets would be far off where the delta wouldn't matter. But, for example, where the fixed insn->off before pointed to pos (target_Y), it now points to pos + delta, so that additional room needs to be taken into account for the check. This means that i) both tests here need to be adjusted into pos + delta, and ii) for the second condition, the test needs to be <= as pos itself can be a target in the backjump, too. Fixes: 9bac3d6d ("bpf: allow extended BPF programs access skb fields") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Alexander Duyck authored
[ Upstream commit 78565208 ] This patch corrects the unaligned accesses seen on GRE TEB tunnels when generating hash keys. Specifically what this patch does is make it so that we force the use of skb_copy_bits when the GRE inner headers will be unaligned due to NET_IP_ALIGNED being a non-zero value. Signed-off-by:
Alexander Duyck <aduyck@mirantis.com> Acked-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
-
Alexander Duyck authored
[ Upstream commit 461547f3, since we lack the flow dissector flags in this release we guard the flow label access using a test on 'skb' being NULL ] This patch fixes an issue with unaligned accesses when using eth_get_headlen on a page that was DMA aligned instead of being IP aligned. The fact is when trying to check the length we don't need to be looking at the flow label so we can reorder the checks to first check if we are supposed to gather the flow label and then make the call to actually get it. v2: Updated path so that either STOP_AT_FLOW_LABEL or KEY_FLOW_LABEL can cause us to check for the flow label. Reported-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 7a84bd46 ] Commit ed5a377d ("sctp: translate host order to network order when setting a hmacid") corrected the hmacid byte-order when setting a hmacid. but the same issue also exists on getting a hmacid. We fix it by changing hmacids to host order when users get them with getsockopt. Fixes: Commit ed5a377d ("sctp: translate host order to network order when setting a hmacid") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Siva Reddy Kallam authored
[ Upstream commit b7d98729 ] tg3_tso_bug() can hit a condition where the entire tx ring is not big enough to segment the GSO packet. For example, if MSS is very small, gso_segs can exceed the tx ring size. When we hit the condition, it will cause tx timeout. tg3_tso_bug() is called to handle TSO and DMA hardware bugs. For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet. For DMA bugs, we can still fall back to linearize the SKB and let the hardware transmit the TSO packet. This patch adds a function tg3_tso_bug_gso_check() to check if there are enough tx descriptors for GSO before calling tg3_tso_bug(). The caller will then handle the error appropriately - drop or lineraize the SKB. v2: Corrected patch description to avoid confusion. Signed-off-by:
Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by:
Michael Chan <mchan@broadcom.com> Acked-by:
Prashant Sreedharan <prashant@broadcom.com> Signed-off-by:
-
Hans Westgaard Ry authored
[ Upstream commit 5f74f82e ] Devices may have limits on the number of fragments in an skb they support. Current codebase uses a constant as maximum for number of fragments one skb can hold and use. When enabling scatter/gather and running traffic with many small messages the codebase uses the maximum number of fragments and may thereby violate the max for certain devices. The patch introduces a global variable as max number of fragments. Signed-off-by:
Hans Westgaard Ry <hans.westgaard.ry@oracle.com> Reviewed-by:
Håkon Bugge <haakon.bugge@oracle.com> Acked-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 415e3d3e ] The commit referenced in the Fixes tag incorrectly accounted the number of in-flight fds over a unix domain socket to the original opener of the file-descriptor. This allows another process to arbitrary deplete the original file-openers resource limit for the maximum of open files. Instead the sending processes and its struct cred should be credited. To do so, we add a reference counted struct user_struct pointer to the scm_fp_list and use it to account for the number of inflight unix fds. Fixes: 712f4aad ("unix: properly account for FDs passed over unix sockets") Reported-by:
David Herrmann <dh.herrmann@gmail.com> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Suggested-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 44c3d0c1 ] Silence lockdep false positive about rcu_dereference() being used in the wrong context. First one should use rcu_dereference_protected() as we own the spinlock. Second one should be a normal assignation, as no barrier is needed. Fixes: 18367681 ("ipv6 flowlabel: Convert np->ipv6_fl_list to RCU.") Reported-by:
Dave Jones <davej@codemonkey.org.uk> Signed-off-by:
-
subashab@codeaurora.org authored
[ Upstream commit 16186a82 ] A rcu stall with the following backtrace was seen on a system with forwarding, optimistic_dad and use_optimistic set. To reproduce, set these flags and allow ipv6 autoconf. This occurs because the device write_lock is acquired while already holding the read_lock. Back trace below - INFO: rcu_preempt self-detected stall on CPU { 1} (t=2100 jiffies g=3992 c=3991 q=4471) <6> Task dump for CPU 1: <2> kworker/1:0 R running task 12168 15 2 0x00000002 <2> Workqueue: ipv6_addrconf addrconf_dad_work <6> Call trace: <2> [<ffffffc000084da8>] el1_irq+0x68/0xdc <2> [<ffffffc000cc4e0c>] _raw_write_lock_bh+0x20/0x30 <2> [<ffffffc000bc5dd8>] __ipv6_dev_ac_inc+0x64/0x1b4 <2> [<ffffffc000bcbd2c>] addrconf_join_anycast+0x9c/0xc4 <2> [<ffffffc000bcf9f0>] __ipv6_ifa_notify+0x160/0x29c <2> [<ffffffc000bcfb7c>] ipv6_ifa_notify+0x50/0x70 <2> [<ffffffc000bd035c>] addrconf_dad_work+0x314/0x334 <2> [<ffffffc0000b64c8>] process_one_work+0x244/0x3fc <2> [<ffffffc0000b7324>] worker_thread+0x2f8/0x418 <2> [<ffffffc0000bb40c>] kthread+0xe0/0xec v2: do addrconf_dad_kick inside read lock and then acquire write lock for ipv6_ifa_notify as suggested by Eric Fixes: 7fd2561e ("net: ipv6: Add a sysctl to make optimistic addresses useful candidates") Cc: Eric Dumazet <edumazet@google.com> Cc: Erik Kline <ek@google.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Acked-by:
-
Hangbin Liu authored
[ Upstream commit 8013d1d7 ] Commit 6fd99094 ("ipv6: Don't reduce hop limit for an interface") disabled accept hop limit from RA if it is smaller than the current hop limit for security stuff. But this behavior kind of break the RFC definition. RFC 4861, 6.3.4. Processing Received Router Advertisements A Router Advertisement field (e.g., Cur Hop Limit, Reachable Time, and Retrans Timer) may contain a value denoting that it is unspecified. In such cases, the parameter should be ignored and the host should continue using whatever value it is already using. If the received Cur Hop Limit value is non-zero, the host SHOULD set its CurHopLimit variable to the received value. So add sysctl option accept_ra_min_hop_limit to let user choose the minimum hop limit value they can accept from RA. And set default to 1 to meet RFC standards. Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Acked-by:
YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com> Signed-off-by:
-
Paolo Abeni authored
[ Upstream commit 1cdda918 ] Currently, the egress interface index specified via IPV6_PKTINFO is ignored by __ip6_datagram_connect(), so that RFC 3542 section 6.7 can be subverted when the user space application calls connect() before sendmsg(). Fix it by initializing properly flowi6_oif in connect() before performing the route lookup. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
-
Paolo Abeni authored
[ Upstream commit 6f21c96a ] The current implementation of ip6_dst_lookup_tail basically ignore the egress ifindex match: if the saddr is set, ip6_route_output() purposefully ignores flowi6_oif, due to the commit d46a9d67 ("net: ipv6: Dont add RT6_LOOKUP_F_IFACE flag if saddr set"), if the saddr is 'any' the first route lookup in ip6_dst_lookup_tail fails, but upon failure a second lookup will be performed with saddr set, thus ignoring the ifindex constraint. This commit adds an output route lookup function variant, which allows the caller to specify lookup flags, and modify ip6_dst_lookup_tail() to enforce the ifindex match on the second lookup via said helper. ip6_route_output() becames now a static inline function build on top of ip6_route_output_flags(); as a side effect, out-of-tree modules need now a GPL license to access the output route lookup functionality. Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit ff5d7497 ] With some combinations of user provided flags in netlink command, it is possible to call tcp_get_info() with a buffer that is not 8-bytes aligned. It does matter on some arches, so we need to use put_unaligned() to store the u64 fields. Current iproute2 package does not trigger this particular issue. Fixes: 0df48c26 ("tcp: add tcpi_bytes_acked to tcp_info") Fixes: 977cb0ec ("tcp: add pacing_rate information into tcp_info") Signed-off-by:
-
Ido Schimmel authored
[ Upstream commit 4f2c6ae5 ] When switchdev drivers process FDB notifications from the underlying device they resolve the netdev to which the entry points to and notify the bridge using the switchdev notifier. However, since the RTNL mutex is not held there is nothing preventing the netdev from disappearing in the middle, which will cause br_switchdev_event() to dereference a non-existing netdev. Make switchdev drivers hold the lock at the beginning of the notification processing session and release it once it ends, after notifying the bridge. Also, remove switchdev_mutex and fdb_lock, as they are no longer needed when RTNL mutex is held. Fixes: 03bf0c28 ("switchdev: introduce switchdev notifier") Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
- 09 Mar, 2016 23 commits
-
-
Marcelo Ricardo Leitner authored
[ Upstream commit 27f7ed2b ] This patch extends commit b93d6471 ("sctp: implement the sender side for SACK-IMMEDIATELY extension") as it didn't white list SCTP_SACK_IMMEDIATELY on sctp_msghdr_parse(), causing it to be understood as an invalid flag and returning -EINVAL to the application. Note that the actual handling of the flag is already there in sctp_datamsg_from_user(). https://tools.ietf.org/html/rfc7053#section-7 Fixes: b93d6471 ("sctp: implement the sender side for SACK-IMMEDIATELY extension") Signed-off-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 9a368aff ] Several times already this has been reported as kasan reports caused by syzkaller and trinity and people always looked at RCU races, but it is much more simple. :) In case we bind a pptp socket multiple times, we simply add it to the callid_sock list but don't remove the old binding. Thus the old socket stays in the bucket with unused call_id indexes and doesn't get cleaned up. This causes various forms of kasan reports which were hard to pinpoint. Simply don't allow multiple binds and correct error handling in pptp_bind. Also keep sk_state bits in place in pptp_connect. Fixes: 00959ade ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)") Cc: Dmitry Kozlov <xeb@mail.ru> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Dmitry Vyukov <dvyukov@google.com> Reported-by:
-
Eric Dumazet authored
[ Upstream commit fa0dc04d ] Dmitry reported a struct pid leak detected by a syzkaller program. Bug happens in unix_stream_recvmsg() when we break the loop when a signal is pending, without properly releasing scm. Fixes: b3ca9b02 ("net: fix multithreaded signal handling in unix recv routines") Reported-by:
-
Eric Dumazet authored
[ Upstream commit e62a123b ] Neal reported crashes with this stack trace : RIP: 0010:[<ffffffff8c57231b>] tcp_v4_send_ack+0x41/0x20f ... CR2: 0000000000000018 CR3: 000000044005c000 CR4: 00000000001427e0 ... [<ffffffff8c57258e>] tcp_v4_reqsk_send_ack+0xa5/0xb4 [<ffffffff8c1a7caa>] tcp_check_req+0x2ea/0x3e0 [<ffffffff8c19e420>] tcp_rcv_state_process+0x850/0x2500 [<ffffffff8c1a6d21>] tcp_v4_do_rcv+0x141/0x330 [<ffffffff8c56cdb2>] sk_backlog_rcv+0x21/0x30 [<ffffffff8c098bbd>] tcp_recvmsg+0x75d/0xf90 [<ffffffff8c0a8700>] inet_recvmsg+0x80/0xa0 [<ffffffff8c17623e>] sock_aio_read+0xee/0x110 [<ffffffff8c066fcf>] do_sync_read+0x6f/0xa0 [<ffffffff8c0673a1>] SyS_read+0x1e1/0x290 [<ffffffff8c5ca262>] system_call_fastpath+0x16/0x1b The problem here is the skb we provide to tcp_v4_send_ack() had to be parked in the backlog of a new TCP fastopen child because this child was owned by the user at the time an out of window packet arrived. Before queuing a packet, TCP has to set skb->dev to NULL as the device could disappear before packet is removed from the queue. Fix this issue by using the net pointer provided by the socket (being a timewait or a request socket). IPv6 is immune to the bug : tcp_v6_send_response() already gets the net pointer from the socket if provided. Fixes: 168a8f58 ("tcp: TCP Fast Open Server - main code path") Reported-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Manfred Rudigier authored
[ Upstream commit 81e8f2e9 ] PHY status frames are not reliable, the PHY may not be able to send them during heavy receive traffic. This overflow condition is signaled by the PHY in the next status frame, but the driver did not make use of it. Instead it always reported wrong tx timestamps to user space after an overflow happened because it assigned newly received tx timestamps to old packets in the queue. This commit fixes this issue by clearing the tx timestamp queue every time an overflow happens, so that no timestamps are delivered for overflow packets. This way time stamping will continue correctly after an overflow. Signed-off-by:
Manfred Rudigier <manfred.rudigier@omicron.at> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Ursula Braun authored
[ Upstream commit 52a82e23 ] Signed-off-by:
Ursula Braun <ursula.braun@de.ibm.com> Reported-by:
Evgeny Cherkashin <Eugene.Crosser@ru.ibm.com> Signed-off-by:
-
Al Viro authored
commit 5129fa48 upstream. ... or we risk seeing a bogus value of d_is_symlink() there. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit a7f77542 upstream. ... otherwise d_is_symlink() above might have nothing to do with the inode value we've got. Signed-off-by:
-
Al Viro authored
commit d4565649 upstream. both do_last() and walk_component() risk picking a NULL inode out of dentry about to become positive, *then* checking its flags and seeing that it's not negative anymore and using (already stale by then) value they'd fetched earlier. Usually ends up oopsing soon after that... Signed-off-by:
-
Al Viro authored
commit c80567c8 upstream. ... into returning a positive to path_openat(), which would interpret that as "symlink had been encountered" and proceed to corrupt memory, etc. It can only happen due to a bug in some ->open() instance or in some LSM hook, etc., so we report any such event *and* make sure it doesn't trick us into further unpleasantness. Signed-off-by:
-
Mikulas Patocka authored
commit b6853f78 upstream. The delete opration can allocate additional space on the HPFS filesystem due to btree split. The HPFS driver checks in advance if there is available space, so that it won't corrupt the btree if we run out of space during splitting. If there is not enough available space, the HPFS driver attempted to truncate the file, but this results in a deadlock since the commit 7dd29d8d ("HPFS: Introduce a global mutex and lock it on every callback from VFS"). This patch removes the code that tries to truncate the file and -ENOSPC is returned instead. If the user hits -ENOSPC on delete, he should try to delete other files (that are stored in a leaf btree node), so that the delete operation will make some space for deleting the file stored in non-leaf btree node. Reported-by:
Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz> Signed-off-by:
-
Guozhonghua authored
commit a4a8481f upstream. When doing append direct io cleanup, if deleting inode fails, it goes out without unlocking inode, which will cause the inode deadlock. This issue was introduced by commit cf1776a9 ("ocfs2: fix a tiny race when truncate dio orohaned entry"). Signed-off-by:
Guozhonghua <guozhonghua@h3c.com> Signed-off-by:
Joseph Qi <joseph.qi@huawei.com> Reviewed-by:
Gang He <ghe@suse.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Andrea Arcangeli authored
commit ad33bb04 upstream. pmd_trans_unstable()/pmd_none_or_trans_huge_or_clear_bad() were introduced to locklessy (but atomically) detect when a pmd is a regular (stable) pmd or when the pmd is unstable and can infinitely transition from pmd_none() and pmd_trans_huge() from under us, while only holding the mmap_sem for reading (for writing not). While holding the mmap_sem only for reading, MADV_DONTNEED can run from under us and so before we can assume the pmd to be a regular stable pmd we need to compare it against pmd_none() and pmd_trans_huge() in an atomic way, with pmd_trans_unstable(). The old pmd_trans_huge() left a tiny window for a race. Useful applications are unlikely to notice the difference as doing MADV_DONTNEED concurrently with a page fault would lead to undefined behavior. [akpm@linux-foundation.org: tidy up comment grammar/layout] Signed-off-by:
Andrea Arcangeli <aarcange@redhat.com> Reported-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
-
Colin Ian King authored
commit 9bf148cb upstream. In the unlikely event that regno == nr_registers then we get an array overrun on regoff because the invalid register check is currently off-by-one. Fix this with a check that regno is >= nr_registers instead. Detected with static analysis using CoverityScan. Fixes: fcc7ffd6 "x86, mpx: Decode MPX instruction to get bound violation information" Signed-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
Dave Hansen <dave.hansen@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Link: http://lkml.kernel.org/r/1456512931-3388-1-git-send-email-colin.king@canonical.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Takashi Iwai authored
commit 473f4145 upstream. Currently the interrupt handler of HD-audio driver assumes that no irq update is needed while processing the irq. But in reality, it has been confirmed that the HW irq is issued even during the irq handling. Since we clear the irq status at the beginning, process the interrupt, then exits from the handler, the lately issued interrupt is left untouched without being properly processed. This patch changes the interrupt handler code to loop over the check-and-process. The handler tries repeatedly as long as the IRQ status are turned on, and either stream or CORB/RIRB is handled. For checking the stream handling, snd_hdac_bus_handle_stream_irq() returns a value indicating the stream indices bits. Other than that, the change is only in the irq handler itself. Reported-by:
Libin Yang <libin.yang@linux.intel.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [ kamal: backport to 4.2-stable: context ] Signed-off-by:
-
Takashi Iwai authored
commit f883982d upstream. HP EliteBook 755 G2 with ALC3228 (ALC280) codec [103c:221c] requires the known fixup (ALC269_FIXUP_HEADSET_MIC) for making the headset mic working. Also, it suffers from the loopback noise problem, so we should disable aamix path as well. Reported-by:
Derick Eddington <derick.eddington@gmail.com> Signed-off-by:
-
David Henningsson authored
commit 2ae95577 upstream. On one of the machines we enable, we found that the actual speaker volume did not always correspond to the volume set in alsamixer. This patch fixes that problem. This patch was orginally written by Kailang @ Realtek, I've rebased it to fit sound git master. BugLink: https://bugs.launchpad.net/bugs/1549660Co-Authored-By:
Kailang <kailang@realtek.com> Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
-
Kailang Yang authored
commit cfc5a845 upstream. Dell create new platform with ALC298 codec. This patch will enable headset mode for ALC225/ALC3253 platform. Signed-off-by:
-
Mike Krinkin authored
commit 17e4bce0 upstream. Ubsan reports the following warning due to a typo in update_accessed_dirty_bits template, the patch fixes the typo: [ 168.791851] ================================================================================ [ 168.791862] UBSAN: Undefined behaviour in arch/x86/kvm/paging_tmpl.h:252:15 [ 168.791866] index 4 is out of range for type 'u64 [4]' [ 168.791871] CPU: 0 PID: 2950 Comm: qemu-system-x86 Tainted: G O L 4.5.0-rc5-next-20160222 #7 [ 168.791873] Hardware name: LENOVO 23205NG/23205NG, BIOS G2ET95WW (2.55 ) 07/09/2013 [ 168.791876] 0000000000000000 ffff8801cfcaf208 ffffffff81c9f780 0000000041b58ab3 [ 168.791882] ffffffff82eb2cc1 ffffffff81c9f6b4 ffff8801cfcaf230 ffff8801cfcaf1e0 [ 168.791886] 0000000000000004 0000000000000001 0000000000000000 ffffffffa1981600 [ 168.791891] Call Trace: [ 168.791899] [<ffffffff81c9f780>] dump_stack+0xcc/0x12c [ 168.791904] [<ffffffff81c9f6b4>] ? _atomic_dec_and_lock+0xc4/0xc4 [ 168.791910] [<ffffffff81da9e81>] ubsan_epilogue+0xd/0x8a [ 168.791914] [<ffffffff81daafa2>] __ubsan_handle_out_of_bounds+0x15c/0x1a3 [ 168.791918] [<ffffffff81daae46>] ? __ubsan_handle_shift_out_of_bounds+0x2bd/0x2bd [ 168.791922] [<ffffffff811287ef>] ? get_user_pages_fast+0x2bf/0x360 [ 168.791954] [<ffffffffa1794050>] ? kvm_largepages_enabled+0x30/0x30 [kvm] [ 168.791958] [<ffffffff81128530>] ? __get_user_pages_fast+0x360/0x360 [ 168.791987] [<ffffffffa181b818>] paging64_walk_addr_generic+0x1b28/0x2600 [kvm] [ 168.792014] [<ffffffffa1819cf0>] ? init_kvm_mmu+0x1100/0x1100 [kvm] [ 168.792019] [<ffffffff8129e350>] ? debug_check_no_locks_freed+0x350/0x350 [ 168.792044] [<ffffffffa1819cf0>] ? init_kvm_mmu+0x1100/0x1100 [kvm] [ 168.792076] [<ffffffffa181c36d>] paging64_gva_to_gpa+0x7d/0x110 [kvm] [ 168.792121] [<ffffffffa181c2f0>] ? paging64_walk_addr_generic+0x2600/0x2600 [kvm] [ 168.792130] [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90 [ 168.792178] [<ffffffffa17d9a4a>] emulator_read_write_onepage+0x27a/0x1150 [kvm] [ 168.792208] [<ffffffffa1794d44>] ? __kvm_read_guest_page+0x54/0x70 [kvm] [ 168.792234] [<ffffffffa17d97d0>] ? kvm_task_switch+0x160/0x160 [kvm] [ 168.792238] [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90 [ 168.792263] [<ffffffffa17daa07>] emulator_read_write+0xe7/0x6d0 [kvm] [ 168.792290] [<ffffffffa183b620>] ? em_cr_write+0x230/0x230 [kvm] [ 168.792314] [<ffffffffa17db005>] emulator_write_emulated+0x15/0x20 [kvm] [ 168.792340] [<ffffffffa18465f8>] segmented_write+0xf8/0x130 [kvm] [ 168.792367] [<ffffffffa1846500>] ? em_lgdt+0x20/0x20 [kvm] [ 168.792374] [<ffffffffa14db512>] ? vmx_read_guest_seg_ar+0x42/0x1e0 [kvm_intel] [ 168.792400] [<ffffffffa1846d82>] writeback+0x3f2/0x700 [kvm] [ 168.792424] [<ffffffffa1846990>] ? em_sidt+0xa0/0xa0 [kvm] [ 168.792449] [<ffffffffa185554d>] ? x86_decode_insn+0x1b3d/0x4f70 [kvm] [ 168.792474] [<ffffffffa1859032>] x86_emulate_insn+0x572/0x3010 [kvm] [ 168.792499] [<ffffffffa17e71dd>] x86_emulate_instruction+0x3bd/0x2110 [kvm] [ 168.792524] [<ffffffffa17e6e20>] ? reexecute_instruction.part.110+0x2e0/0x2e0 [kvm] [ 168.792532] [<ffffffffa14e9a81>] handle_ept_misconfig+0x61/0x460 [kvm_intel] [ 168.792539] [<ffffffffa14e9a20>] ? handle_pause+0x450/0x450 [kvm_intel] [ 168.792546] [<ffffffffa15130ea>] vmx_handle_exit+0xd6a/0x1ad0 [kvm_intel] [ 168.792572] [<ffffffffa17f6a6c>] ? kvm_arch_vcpu_ioctl_run+0xbdc/0x6090 [kvm] [ 168.792597] [<ffffffffa17f6bcd>] kvm_arch_vcpu_ioctl_run+0xd3d/0x6090 [kvm] [ 168.792621] [<ffffffffa17f6a6c>] ? kvm_arch_vcpu_ioctl_run+0xbdc/0x6090 [kvm] [ 168.792627] [<ffffffff8293b530>] ? __ww_mutex_lock_interruptible+0x1630/0x1630 [ 168.792651] [<ffffffffa17f5e90>] ? kvm_arch_vcpu_runnable+0x4f0/0x4f0 [kvm] [ 168.792656] [<ffffffff811eeb30>] ? preempt_notifier_unregister+0x190/0x190 [ 168.792681] [<ffffffffa17e0447>] ? kvm_arch_vcpu_load+0x127/0x650 [kvm] [ 168.792704] [<ffffffffa178e9a3>] kvm_vcpu_ioctl+0x553/0xda0 [kvm] [ 168.792727] [<ffffffffa178e450>] ? vcpu_put+0x40/0x40 [kvm] [ 168.792732] [<ffffffff8129e350>] ? debug_check_no_locks_freed+0x350/0x350 [ 168.792735] [<ffffffff82946087>] ? _raw_spin_unlock+0x27/0x40 [ 168.792740] [<ffffffff8163a943>] ? handle_mm_fault+0x1673/0x2e40 [ 168.792744] [<ffffffff8129daa8>] ? trace_hardirqs_on_caller+0x478/0x6c0 [ 168.792747] [<ffffffff8129dcfd>] ? trace_hardirqs_on+0xd/0x10 [ 168.792751] [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90 [ 168.792756] [<ffffffff81725a80>] do_vfs_ioctl+0x1b0/0x12b0 [ 168.792759] [<ffffffff817258d0>] ? ioctl_preallocate+0x210/0x210 [ 168.792763] [<ffffffff8174aef3>] ? __fget+0x273/0x4a0 [ 168.792766] [<ffffffff8174acd0>] ? __fget+0x50/0x4a0 [ 168.792770] [<ffffffff8174b1f6>] ? __fget_light+0x96/0x2b0 [ 168.792773] [<ffffffff81726bf9>] SyS_ioctl+0x79/0x90 [ 168.792777] [<ffffffff82946880>] entry_SYSCALL_64_fastpath+0x23/0xc1 [ 168.792780] ================================================================================ Signed-off-by:
Mike Krinkin <krinkin.m.u@gmail.com> Reviewed-by:
Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Kai-Heng Feng authored
commit 3b43b71f upstream. After login to the desktop on Dell Inspiron 3162, there's a very loud background noise comes from the builtin speaker. The noise does not go away even if the speaker is muted. The noise disappears after using the aamix fixup. Codec: Realtek ALC3234 Address: 0 AFG Function Id: 0x1 (unsol 1) Vendor Id: 0x10ec0255 Subsystem Id: 0x10280725 Revision Id: 0x100002 No Modem Function Group found BugLink: http://bugs.launchpad.net/bugs/1549620Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
Ilya Dryomov authored
commit dbc0d3ca upstream. ceph_msg_footer is 21 bytes long, while ceph_msg_footer_old is only 13. Don't skip too much when CEPH_FEATURE_MSG_AUTH isn't negotiated. Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Ilya Dryomov authored
commit e7a88e82 upstream. The contract between try_read() and try_write() is that when called each processes as much data as possible. When instructed by osd_client to skip a message, try_read() is violating this contract by returning after receiving and discarding a single message instead of checking for more. try_write() then gets a chance to write out more requests, generating more replies/skips for try_read() to handle, forcing the messenger into a starvation loop. Reported-by:
Varada Kari <Varada.Kari@sandisk.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit d045437a upstream. The ftrace:function event is only displayed for parsing the function tracer data. It is not used to enable function tracing, and does not include an "enable" file in its event directory. Originally, this event was kept separate from other events because it did not have a ->reg parameter. But perf added a "reg" parameter for its use which caused issues, because it made the event available to functions where it was not compatible for. Commit 9b63776f "tracing: Do not enable function event with enable" added a TRACE_EVENT_FL_IGNORE_ENABLE flag that prevented the function event from being enabled by normal trace events. But this commit missed keeping the function event from being displayed by the "available_events" directory, which is used to show what events can be enabled by set_event. One documented way to enable all events is to: cat available_events > set_event But because the function event is displayed in the available_events, this now causes an INVALID error: cat: write error: Invalid argument Reported-by:
Chunyu Hu <chuhu@redhat.com> Fixes: 9b63776f "tracing: Do not enable function event with enable" Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
