[ Upstream commit 2a580949 ]

The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 48d99f47 upstream.

Commit 554cdaef ('ARM: orion5x: Refactor
mpp code to use common orion platform mpp.') seems to have accidentally
inverted the GPIO valid bits for MPP9 (only).  For the mv2120 platform
which uses MPP9 as a GPIO LED device, this results in the error:

[   12.711476] leds-gpio: probe of leds-gpio failed with error -22
Reported-by: Henry von Tresckow <hvontres@gmail.com>
References: http://bugs.debian.org/667446Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Hans Henry von Tresckow <hvontres@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f55205f4 upstream.

I think this is a typo.
To ensure new voltage setting won't greater than desc->max,
the equation should be desc->min + desc->step * new_val <= desc->max.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fde165b2 upstream.

Commit 4e8ee7de (ARM: SMP: use
idmap_pgd for mapping MMU enable during secondary booting)
switched secondary boot to use idmap_pgd, which is initialized
during early_initcall, instead of a page table initialized during
__cpu_up.  This causes idmap_pgd to contain the static mappings
but be missing all dynamic mappings.

If a console is registered that creates a dynamic mapping, the
printk in secondary_start_kernel will trigger a data abort on
the missing mapping before the exception handlers have been
initialized, leading to a hang.  Initial boot is not affected
because no consoles have been registered, and resume is usually
not affected because the offending console is suspended.
Onlining a cpu with hotplug triggers the problem.

A workaround is to the printk in secondary_start_kernel until
after the page tables have been switched back to init_mm.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e787ec13 upstream.

The inline assembly in kernel_execve() uses r8 and r9.  Since this
code sequence does not return, it usually doesn't matter if the
register clobber list is accurate.  However, I saw a case where a
particular version of gcc used r8 as an intermediate for the value
eventually passed to r9.  Because r8 is used in the inline
assembly, and not mentioned in the clobber list, r9 was set
to an incorrect value.

This resulted in a kernel panic on execution of the first user-space
program in the system.  r9 is used in ret_to_user as the thread_info
pointer, and if it's wrong, bad things happen.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2f624278 upstream.

We really need to use a ACCESS_ONCE() on the sequence value read in
__read_seqcount_begin(), because otherwise the compiler might end up
reloading the value in between the test and the return of it.  As a
result, it might end up returning an odd value (which means that a write
is in progress).

If the reader is then fast enough that that odd value is still the
current one when the read_seqcount_retry() is done, we might end up with
a "successful" read sequence, even despite the concurrent write being
active.

In practice this probably never really happens - there just isn't
anything else going on around the read of the sequence count, and the
common case is that we end up having a read barrier immediately
afterwards.

So the code sequence in which gcc might decide to reaload from memory is
small, and there's no reason to believe it would ever actually do the
reload.  But if the compiler ever were to decide to do so, it would be
incredibly annoying to debug.  Let's just make sure.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f5c2347e upstream.

<asm-generic/statfs.h> is exported to userspace, so using
BITS_PER_LONG is invalid.  We need to use __BITS_PER_LONG instead.

This is kernel bugzilla 43165.
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1335465916-16965-1-git-send-email-hpa@linux.intel.comAcked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d5e28005 upstream.

With the embed percpu first chunk allocator, x86 uses either PAGE_SIZE
or PMD_SIZE for atom_size.  PMD_SIZE is used when CPU supports PSE so
that percpu areas are aligned to PMD mappings and possibly allow using
PMD mappings in vmalloc areas in the future.  Using larger atom_size
doesn't waste actual memory; however, it does require larger vmalloc
space allocation later on for !first chunks.

With reasonably sized vmalloc area, PMD_SIZE shouldn't be a problem
but x86_32 at this point is anything but reasonable in terms of
address space and using larger atom_size reportedly leads to frequent
percpu allocation failures on certain setups.

As there is no reason to not use PMD_SIZE on x86_64 as vmalloc space
is aplenty and most x86_64 configurations support PSE, fix the issue
by always using PMD_SIZE on x86_64 and PAGE_SIZE on x86_32.

v2: drop cpu_has_pse test and make x86_64 always use PMD_SIZE and
    x86_32 PAGE_SIZE as suggested by hpa.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Yanmin Zhang <yanmin.zhang@intel.com>
Reported-by: ShuoX Liu <shuox.liu@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4F97BA98.6010001@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 76a8df7b upstream.

The accessing PCI configuration space with the PCI BIOS32 service does
not work in PV guests.

On systems without MMCONFIG or where the BIOS hasn't marked the
MMCONFIG region as reserved in the e820 map, the BIOS service is
probed (even though direct access is preferred) and this hangs.
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
[v1: Fixed compile error when CONFIG_PCI is not set]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b7e5ffe5 upstream.

If I try to do "cat /sys/kernel/debug/kernel_page_tables"
I end up with:

BUG: unable to handle kernel paging request at ffffc7fffffff000
IP: [<ffffffff8106aa51>] ptdump_show+0x221/0x480
PGD 0
Oops: 0000 [#1] SMP
CPU 0
.. snip..
RAX: 0000000000000000 RBX: ffffc00000000fff RCX: 0000000000000000
RDX: 0000800000000000 RSI: 0000000000000000 RDI: ffffc7fffffff000

which is due to the fact we are trying to access a PFN that is not
accessible to us. The reason (at least in this case) was that
PGD[256] is set to __HYPERVISOR_VIRT_START which was setup (by the
hypervisor) to point to a read-only linear map of the MFN->PFN array.
During our parsing we would get the MFN (a valid one), try to look
it up in the MFN->PFN tree and find it invalid and return ~0 as PFN.
Then pte_mfn_to_pfn would happilly feed that in, attach the flags
and return it back to the caller. 'ptdump_show' bitshifts it and
gets and invalid value that it tries to dereference.

Instead of doing all of that, we detect the ~0 case and just
return !_PAGE_PRESENT.

This bug has been in existence .. at least until 2.6.37 (yikes!)
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 07d69d42 upstream.

Without this patch sysfs reports the cable as present

flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1

while it's not:

flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link

Tested on my Beagle XM.

v2: added mantainer to the list of recipient
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6f24f892 upstream.

Commit ec81aecb ("hfs: fix a potential buffer overflow") fixed a few
potential buffer overflows in the hfs filesystem.  But as Timo Warns
pointed out, these changes also need to be made on the hfsplus
filesystem as well.
Reported-by: Timo Warns <warns@pre-sense.de>
Acked-by: WANG Cong <amwang@redhat.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Cc: Sage Weil <sage@newdream.net>
Cc: Eugene Teo <eteo@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dave Anderson <anderson@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

commit c308b56b upstream.
[ backported to 3.0 by Kerin Millar <kerframil@gmail.com>]

Various people reported nohz load tracking still being wrecked, but Doug
spotted the actual problem. We fold the nohz remainder in too soon,
causing us to loose samples and under-account.

So instead of playing catch-up up-front, always do a single load-fold
with whatever state we encounter and only then fold the nohz remainder
and play catch-up.
Reported-by: Doug Smythies <dsmythies@telus.net>
Reported-by: LesÅ=82aw Kope=C4=87 <leslaw.kopec@nasza-klasa.pl>
Reported-by: Aman Gupta <aman@tmm1.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-4v31etnhgg9kwd6ocgx3rxl8@git.kernel.orgSigned-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Kerin Millar <kerframil@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4c1bcdb5 upstream.

This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 328c32f0 upstream.

Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.

Fix this by freeing glue data last.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 44eb65cf upstream.

Under some circumstances, a PCI-based driver reports the following OOPs:

Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Oops: 0000 [#1] SMP
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Pid: 19627, comm: rmmod
Not tainted 3.2.9-2.fc16.x86_64 #1 LENOVO 05962RU/05962RU
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP:
0010:[<ffffffffa0418d39>]  [<ffffffffa0418d39>]
rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Process rmmod (pid:
19627, threadinfo ffff880050262000, task ffff8801156d5cc0)
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Stack:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000002
ffff8801176c2540 ffff880050263ca8 ffffffffa03348e7
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000282
0000000180150014 ffff880050263fd8 ffff8801176c2810
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  ffff880050263bc8
ffffffff810550e2 00000000000002c0 ffff8801176c0d40
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Call Trace:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  [<ffffffffa03348e7>]
_rtl_pci_rx_interrupt+0x187/0x650 [rtlwifi]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Code: ff 09 d0 89 07 48
83 c4 08 5b 5d c3 66 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66
66 66 90 40 84 f6 89 d3 74 13 84 d2 75 57 <8b> 07 48 83 c4 08 5b 5d c1
e8 1f c3 0f 1f 00 84 d2 74 ed 80 fa
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP
[<ffffffffa0418d39>] rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  RSP <ffff880050263b58>
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] CR2: 00000000000006e0
Mar 19 08:14:35 kvothe kernel: [ 6584.646491] ---[ end trace
8636c766dcfbe0e6 ]---

This oops is due to interrupts not being disabled in this particular path.
Reported-by: Dave Airlie <airlied@gmail.com>
Tested-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 66f2c99a upstream.

EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dd447319 upstream.

Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution.  Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:

Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.

After that you need to reload the driver to get it working again.

This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097
https://bugzilla.redhat.com/show_bug.cgi?id=802106

This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6c557cfe upstream.

In the driver's suspend function, clk_enable() was used instead of
clk_disable(). This is corrected with this patch.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
[wsa: reworded commit header slightly]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6868225e upstream.

Commit d9027470("[libata] Add ATA transport class") introduced
ATA_EFLAG_OLD_ER to mark entries in the error ring as cleared.

But ata_count_probe_trials_cb() didn't check this flag and it still
counts the old error history. So wrong probe trials count is returned
and it causes problem, for example, SATA link speed is slowed down from
3.0Gbps to 1.5Gbps.

Fix it by checking ATA_EFLAG_OLD_ER in ata_count_probe_trials_cb().
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b7048711 upstream.

coretemp tries to access core_data array beyond bounds on cpu unplug if
core id of the cpu if more than NUM_REAL_CORES-1.

BUG: unable to handle kernel NULL pointer dereference at 000000000000013c
IP: [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
PGD 673e5a067 PUD 66e9b3067 PMD 0
Oops: 0000 [#1] SMP
CPU 79
Modules linked in: sunrpc cpufreq_ondemand acpi_cpufreq freq_table mperf bnep bluetooth rfkill ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter nf_conntrack_ipv4 nf_defrag_ipv4 ip6_tables xt_state nf_conntrack coretemp crc32c_intel asix tpm_tis pcspkr usbnet iTCO_wdt i2c_i801 microcode mii joydev tpm i2c_core iTCO_vendor_support tpm_bios i7core_edac igb ioatdma edac_core dca megaraid_sas [last unloaded: oprofile]

Pid: 3315, comm: set-cpus Tainted: G        W    3.4.0-rc5+ #2 QCI QSSC-S4R/QSSC-S4R
RIP: 0010:[<ffffffffa00159af>]  [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
RSP: 0018:ffff880472fb3d48  EFLAGS: 00010246
RAX: 0000000000000124 RBX: 0000000000000034 RCX: 00000000ffffffff
RDX: 0000000000000000 RSI: 0000000000000046 RDI: 0000000000000246
RBP: ffff880472fb3d88 R08: ffff88077fcd36c0 R09: 0000000000000001
R10: ffffffff8184bc48 R11: 0000000000000000 R12: ffff880273095800
R13: 0000000000000013 R14: ffff8802730a1810 R15: 0000000000000000
FS:  00007f694a20f720(0000) GS:ffff88077fcc0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 000000000000013c CR3: 000000067209b000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process set-cpus (pid: 3315, threadinfo ffff880472fb2000, task ffff880471fa0000)
Stack:
 ffff880277b4c308 0000000000000003 ffff880472fb3d88 0000000000000005
 0000000000000034 00000000ffffffd1 ffffffff81cadc70 ffff880472fb3e14
 ffff880472fb3dc8 ffffffff8161f48d ffff880471fa0000 0000000000000034
Call Trace:
 [<ffffffff8161f48d>] notifier_call_chain+0x4d/0x70
 [<ffffffff8107f1be>] __raw_notifier_call_chain+0xe/0x10
 [<ffffffff81059d30>] __cpu_notify+0x20/0x40
 [<ffffffff815fa251>] _cpu_down+0x81/0x270
 [<ffffffff815fa477>] cpu_down+0x37/0x50
 [<ffffffff815fd6a3>] store_online+0x63/0xc0
 [<ffffffff813c7078>] dev_attr_store+0x18/0x30
 [<ffffffff811f02cf>] sysfs_write_file+0xef/0x170
 [<ffffffff81180443>] vfs_write+0xb3/0x180
 [<ffffffff8118076a>] sys_write+0x4a/0x90
 [<ffffffff816236a9>] system_call_fastpath+0x16/0x1b
Code: 48 c7 c7 94 60 01 a0 44 0f b7 ac 10 ac 00 00 00 31 c0 e8 41 b7 5f e1 41 83 c5 02 49 63 c5 49 8b 44 c4 10 48 85 c0 74 56 45 31 ff <39> 58 18 75 4e eb 1f 49 63 d7 4c 89 f7 48 89 45 c8 48 6b d2 28
RIP  [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
 RSP <ffff880472fb3d48>
CR2: 000000000000013c
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bdc71c9a upstream.

CPU core ID is used to index the core_data[] array. The core ID is, however, not
sequential; 10-core CPUS can have a core ID as high as 25. Increase the limit to
32 to be able to deal with current CPUs.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 54b3a4d3 upstream.

Ben Hutchings pointed out that the validation in efivars was inadequate -
most obviously, an entry with size 0 would server as a DoS against the
kernel. Improve this based on his suggestions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fec6c20b upstream.

A common flaw in UEFI systems is a refusal to POST triggered by a malformed
boot variable. Once in this state, machines may only be restored by
reflashing their firmware with an external hardware device. While this is
obviously a firmware bug, the serious nature of the outcome suggests that
operating systems should filter their variable writes in order to prevent
a malicious user from rendering the machine unusable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b728a5c8 upstream.

drivers/firmware/efivars.c:161: warning: ‘utf16_strlen’ defined but not used
utf16_strlen() is only used inside CONFIG_PSTORE - make this "static inline"
to shut the compiler up [thanks to hpa for the suggestion].

drivers/firmware/efivars.c:602: warning: initialization from incompatible pointer type
Between v1 and v2 of this patch series we decided to make the "part" number
unsigned - but missed fixing the stub version of efi_pstore_write()
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Mike Waychison <mikew@google.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[took the static part of the patch, not the pstore part, for 3.0-stable,
to fix the compiler warning we had - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a2940908 upstream.

Fix the string functions in the efivars driver to be called utf16_*
instead of utf8_* as the encoding is utf16, not utf8.

As well, rename utf16_strlen to utf16_strnlen as it takes a maxlength
argument and the name should be consistent with the standard C function
names.  utf16_strlen is still provided for convenience in a subsequent
patch.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 41b3254c upstream.

More recent versions of the UEFI spec have added new attributes for
variables. Add them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7d1d8651 upstream.

Normalize phy->attached_sas_addr to return a zero-address in the case
when device-type == NO_DEVICE or the linkrate is invalid to handle
expanders that put non-zero sas addresses in the discovery response:

 sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device)
 sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device)
 sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device)
 sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device)
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1699490d upstream.

If an expander reports 'PHY VACANT' for a phy index prior to the one
that generated a BCN libsas fails rediscovery.  Since a vacant phy is
defined as a valid phy index that will never have an attached device
just continue the search.
Signed-off-by: Thomas Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6a1c5312 upstream.

TPIDRURW is a user read/write register forming part of the group of
thread registers in more recent versions of the ARM architecture (~v6+).

Currently, the kernel does not touch this register, which allows tasks
to communicate covertly by reading and writing to the register without
context-switching affecting its contents.

This patch clears TPIDRURW when TPIDRURO is updated via the set_tls
macro, which is called directly from __switch_to. Since the current
behaviour makes the register useless to userspace as far as thread
pointers are concerned, simply clearing the register (rather than saving
and restoring it) will not cause any problems to userspace.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 64f371bc upstream.

The autofs packet size has had a very unfortunate size problem on x86:
because the alignment of 'u64' differs in 32-bit and 64-bit modes, and
because the packet data was not 8-byte aligned, the size of the autofsv5
packet structure differed between 32-bit and 64-bit modes despite
looking otherwise identical (300 vs 304 bytes respectively).

We first fixed that up by making the 64-bit compat mode know about this
problem in commit a32744d4 ("autofs: work around unhappy compat
problem on x86-64"), and that made a 32-bit 'systemd' work happily on a
64-bit kernel because everything then worked the same way as on a 32-bit
kernel.

But it turned out that 'automount' had actually known and worked around
this problem in user space, so fixing the kernel to do the proper 32-bit
compatibility handling actually *broke* 32-bit automount on a 64-bit
kernel, because it knew that the packet sizes were wrong and expected
those incorrect sizes.

As a result, we ended up reverting that compatibility mode fix, and
thus breaking systemd again, in commit fcbf94b9.

With both automount and systemd doing a single read() system call, and
verifying that they get *exactly* the size they expect but using
different sizes, it seemed that fixing one of them inevitably seemed to
break the other.  At one point, a patch I seriously considered applying
from Michael Tokarev did a "strcmp()" to see if it was automount that
was doing the operation.  Ugly, ugly.

However, a prettier solution exists now thanks to the packetized pipe
mode.  By marking the communication pipe as being packetized (by simply
setting the O_DIRECT flag), we can always just write the bigger packet
size, and if user-space does a smaller read, it will just get that
partial end result and the extra alignment padding will simply be thrown
away.

This makes both automount and systemd happy, since they now get the size
they asked for, and the kernel side of autofs simply no longer needs to
care - it could pad out the packet arbitrarily.

Of course, if there is some *other* user of autofs (please, please,
please tell me it ain't so - and we haven't heard of any) that tries to
read the packets with multiple writes, that other user will now be
broken - the whole point of the packetized mode is that one system call
gets exactly one packet, and you cannot read a packet in pieces.
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Ian Kent <raven@themaw.net>
Cc: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9883035a upstream.

The actual internal pipe implementation is already really about
individual packets (called "pipe buffers"), and this simply exposes that
as a special packetized mode.

When we are in the packetized mode (marked by O_DIRECT as suggested by
Alan Cox), a write() on a pipe will not merge the new data with previous
writes, so each write will get a pipe buffer of its own.  The pipe
buffer is then marked with the PIPE_BUF_FLAG_PACKET flag, which in turn
will tell the reader side to break the read at that boundary (and throw
away any partial packet contents that do not fit in the read buffer).

End result: as long as you do writes less than PIPE_BUF in size (so that
the pipe doesn't have to split them up), you can now treat the pipe as a
packet interface, where each read() system call will read one packet at
a time.  You can just use a sufficiently big read buffer (PIPE_BUF is
sufficient, since bigger than that doesn't guarantee atomicity anyway),
and the return value of the read() will naturally give you the size of
the packet.

NOTE! We do not support zero-sized packets, and zero-sized reads and
writes to a pipe continue to be no-ops.  Also note that big packets will
currently be split at write time, but that the size at which that
happens is not really specified (except that it's bigger than PIPE_BUF).
Currently that limit is the system page size, but we might want to
explicitly support bigger packets some day.

The main user for this is going to be the autofs packet interface,
allowing us to stop having to care so deeply about exact packet sizes
(which have had bugs with 32/64-bit compatibility modes).  But user
space can create packetized pipes with "pipe2(fd, O_DIRECT)", which will
fail with an EINVAL on kernels that do not support this interface.
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Ian Kent <raven@themaw.net>
Cc: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6f6543f5 upstream.

The field is used to pass the UVC request data length, but can also be
used to signal an error when setting it to a negative value. Switch from
unsigned int to __s32.
Reported-by: Fernandez Gonzalo <gfernandez@copreci.es>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c85dcdac upstream.

This patch (as1539) fixes a minor bug in the mass-storage gadget
drivers.  When an unknown command is received, the error code sent
back is "Invalid Field in CDB" rather than "Invalid Command".  This is
because the bitmask of CDB bytes allowed to be nonzero is incorrect.

When handling an unknown command, we don't care which command bytes
are nonzero.  All the bits in the mask should be set, not just eight
of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 151b6128 upstream.

This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

This fixes Bugzilla #42728.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5c22837a upstream.

This patch fixes a race whereby a pointer to a buffer
would be overwritten while the buffer was in use leading
to a double free and a memory leak. This causes crashes.
This bug was introduced in 2.6.34
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit d39514c1 which is
e90fc3cb upstream as it causes oopses on
some ppc systems.
Reported-by: Chen Peter-B29397 <B29397@freescale.com>
Cc: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 04da6e9d upstream.

nfsd_open() already returns an NFS error value; only vfs_test_lock()
result needs to be fed through nfserrno().  Broken by commit 55ef12
(nfsd: Ensure nfsv4 calls the underlying filesystem on LOCKT)
three years ago...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 96f6f985 upstream.

..._want_write() returns -EROFS on failure, _not_ an NFS error value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>