- 15 Jul, 2015 40 commits
-
-
Alex Deucher authored
commit 39fa10f7 upstream. Since we are messing with state in the worker. v2: drop the changes in the mst worker Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Vincent Fann authored
commit 1277fa2a upstream. Several of these drivers have there TX randomly blocked for 3~5 seconds while measuring tx throughput (iperf). The root couse happens in rtl_pci_flush(). The function uses a while-loop to wait for TX queue length to decrease to 0. The TX queue length counts the number of packets that are queued in the driver. The driver relys on the TX OK interrupt to return skb and reduce TX queue length. The interrupt subroutine disables interupts, reads the interrupt registers, and then clears the registers in the beginning of _rtl_pci_interrupt(). After all interupts process are finished, the driver invokes enable_interrupt() to enable interupts. This behavior is normal for an interrupt subroutine. But enable_interrupt() invokes clear_interrupt() again. This unexpected interrupt clearing may cleari me fresh TX OK interrupts. These missing interrupts cause TX queue length to never reduce to 0i, which causes rtl_pci_flush() to be stuck in unterminated while-loop. This patch removes clear_interrupt() in enable_interrupt() to avoid this behavior. Signed-off-by:
Vincent Fann <vincent_fann@realtek.com> Signed-off-by:
Shao Fu <shaofu@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Gregory CLEMENT authored
commit ce2f6ea1 upstream. The commit df59fa7f "spi: orion: support armada extended baud rates" was too optimistic for the maximum baud rate that the Armada SoCs can support. According to the hardware datasheet the maximum frequency supported by the Armada 370 SoC is tclk/4. But for the Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and for the Armada 375 it is tclk/15. Currently the armada-370-spi compatible is only used by the Armada 370 and the Armada XP device tree. On Armada 370, tclk cannot be higher than 200MHz. In order to be able to handle both SoCs, we can take the minimum of 50MHz and tclk/4. A proper solution is adding a compatible string for each SoC, but it can't be done as a fix for compatibility reason (we can't modify device tree that have been already released) and it will be part of a separate patch. Fixes: df59fa7f (spi: orion: support armada extended baud rates) Reported-by:
Kostya Porotchkin <kostap@marvell.com> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Nicolas Ferre authored
commit 8687634b upstream. In RS485 mode, we may want to set the delay_rts_after_send value to 0. In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but this is exactly the expected behavior if we want no delay... Moreover, if the value was set to non-zero value by device-tree or earlier ioctl command, it was impossible to change it back to zero. Reported-by:
Sami Pietikäinen <Sami.Pietikainen@wapice.com> Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ kamal: backport to 3.19-stable: context ] Signed-off-by:
-
David Fries authored
commit f7134eea upstream. A temperature conversion can take 750 ms and when possible the w1_therm slave driver drops the bus_mutex to allow other bus operations, but that includes operations such as a periodic slave search, which can remove this slave when it is no longer detected. If that happens the sl->family_data will be freed and set to NULL causing w1_slave_show to crash when it wakes up. Signed-off-by:
David Fries <David@Fries.net> Reported-By:
Thorsten Bschorr <thorsten@bschorr.de> Tested-by:
Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by:
-
Tomas Winkler authored
commit fe292283 upstream. HW has to be in known state before the initialisation sequence is started. The polling step for settling aliveness was set to 200ms while in practise this can be done in up to 30msecs. Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Barak Yoresh <barak.yoresh@intel.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit 08249651 upstream. Refine the mechanism introduced by commit f244d8b6 ("ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug") to propagate the ignore_hotplug setting of the device to its parent bridge in case hotplug notifications related to the graphics adapter switching are given for the bridge rather than for the device itself (they need to be ignored in both cases). Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891 Link: https://bugs.freedesktop.org/show_bug.cgi?id=88927 Fixes: b440bde7 ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device") Reported-and-tested-by:
tiagdtd-lava <tiagdtd-lava@yahoo.de> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Mimi Zohar authored
commit f2b3dee4 upstream. The call to asymmetric_key_hex_to_key_id() from ca_keys_setup() silently fails with -ENOMEM. Instead of dynamically allocating memory from a __setup function, this patch defines a variable and calls __asymmetric_key_hex_to_key_id(), a new helper function, directly. This bug was introduced by 'commit 46963b77 ("KEYS: Overhaul key identification when searching for asymmetric keys")'. Changelog: - for clarification, rename hexlen to asciihexlen in asymmetric_key_hex_to_key_id() - add size argument to __asymmetric_key_hex_to_key_id() - David Howells - inline __asymmetric_key_hex_to_key_id() - David Howells - remove duplicate strlen() calls Acked-by:
David Howells <dhowells@redhat.com> Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
-
Mimi Zohar authored
commit cd025f7f upstream. Include don't appraise or measure rules for the NSFS filesystem in the builtin ima_tcb and ima_appraise_tcb policies. Changelog: - Update documentation Signed-off-by:
-
Roberto Sassu authored
commit 6438de9f upstream. This patch adds a rule in the default measurement policy to skip inodes in the cgroupfs filesystem. Measurements for this filesystem can be avoided, as all the digests collected have the same value of the digest of an empty file. Furthermore, this patch updates the documentation of IMA policies in Documentation/ABI/testing/ima_policy to make it consistent with the policies set in security/integrity/ima/ima_policy.c. Signed-off-by:
Roberto Sassu <rsassu@suse.de> Signed-off-by:
-
Paolo Bonzini authored
commit 69a12200 upstream. The argument to KVM_GET_DIRTY_LOG is a memslot id; it may not match the position in the memslots array, which is sorted by gfn. Reviewed-by:
James Hogan <james.hogan@imgtec.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit a44074f1 upstream. Although it is possible to let SRP I/O continue if a reconnect results in a reduction of the number of channels, the current code does not handle this scenario correctly. Instead of making the reconnect code more complex, consider this as a reconnection failure. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit c014c8cd upstream. Reception of a DREQ message only causes the state of a single channel to change. Hence move the 'connected' member variable from the target to the channel data structure. This patch avoids that following false positive warning can be reported by srp_destroy_qp(): WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:617 srp_destroy_qp+0xa6/0x120 [ib_srp]() Call Trace: [<ffffffff8106e10f>] warn_slowpath_common+0x7f/0xc0 [<ffffffff8106e16a>] warn_slowpath_null+0x1a/0x20 [<ffffffffa0440226>] srp_destroy_qp+0xa6/0x120 [ib_srp] [<ffffffffa0440322>] srp_free_ch_ib+0x82/0x1e0 [ib_srp] [<ffffffffa044408b>] srp_create_target+0x7ab/0x998 [ib_srp] [<ffffffff81346f60>] dev_attr_store+0x20/0x30 [<ffffffff811dd90f>] sysfs_write_file+0xef/0x170 [<ffffffff8116d248>] vfs_write+0xc8/0x190 [<ffffffff8116d411>] sys_write+0x51/0x90 Signed-off-by:
-
Bart Van Assche authored
commit 8de9fe3a upstream. Avoid that receiving a DREQ while RDMA channels are being established causes target->qp_in_error to be reset. Signed-off-by:
-
Bart Van Assche authored
commit fb49c8bb upstream. Fix a scsi_get_host() / scsi_host_put() imbalance in the error path of srp_create_target(). See also patch "IB/srp: Avoid that I/O hangs due to a cable pull during LUN scanning" (commit ID 34aa654e). Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Signed-off-by:
-
Bart Van Assche authored
commit 535fb906 upstream. Avoid that srp_terminate_io() can get invoked while srp_queuecommand() is in progress. This patch avoids that an I/O timeout can trigger the following kernel warning: WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:1447 srp_terminate_io+0xef/0x100 [ib_srp]() Call Trace: [<ffffffff814c65a2>] dump_stack+0x4e/0x68 [<ffffffff81051f71>] warn_slowpath_common+0x81/0xa0 [<ffffffff8105204a>] warn_slowpath_null+0x1a/0x20 [<ffffffffa075f51f>] srp_terminate_io+0xef/0x100 [ib_srp] [<ffffffffa07495da>] __rport_fail_io_fast+0xba/0xc0 [scsi_transport_srp] [<ffffffffa0749a90>] rport_fast_io_fail_timedout+0xe0/0xf0 [scsi_transport_srp] [<ffffffff8106e09b>] process_one_work+0x1db/0x780 [<ffffffff8106e75b>] worker_thread+0x11b/0x450 [<ffffffff81073c64>] kthread+0xe4/0x100 [<ffffffff814cf26c>] ret_from_fork+0x7c/0xb0 See also patch "scsi_transport_srp: Add transport layer error handling" (commit ID 29c17324). Signed-off-by:
-
Bart Van Assche authored
commit be34c62d upstream. Introduce the helper function srp_wait_for_queuecommand(). Move the definition of scsi_request_fn_active(). Add a comment above srp_wait_for_queuecommand() that support for scsi-mq needs to be added. This patch does not change any functionality. A second call to srp_wait_for_queuecommand() will be introduced in the next patch. Signed-off-by:
-
Zhichang Yuan authored
commit 5dbb4c61 upstream. 41f8bba7 ("of/pci: Add pci_register_io_range() and pci_pio_to_address()") added support for systems with several I/O ranges described by OF bindings. It modified pci_address_to_pio() look up the io_range for a given CPU physical address, but the conversion was wrong. Fix the conversion of address to I/O port. [bhelgaas: changelog] Fixes: 41f8bba7 ("of/pci: Add pci_register_io_range() and pci_pio_to_address()") Signed-off-by:
Zhichang Yuan <yuanzhichang@hisilicon.com> Signed-off-by:
Liviu Dudau <Liviu.Dudau@arm.com> Signed-off-by:
-
Axel Lin authored
commit 12c35005 upstream. WM8955_K_8_0_MASK bits is controlled by WM8955_PLL_CONTROL_3 rather than WM8955_PLL_CONTROL_2. Signed-off-by:
Axel Lin <axel.lin@ingics.com> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Eric W. Biederman authored
commit 1b852bce upstream. Fresh mounts of proc and sysfs are a very special case that works very much like a bind mount. Unfortunately the current structure can not preserve the MNT_LOCK... mount flags. Therefore refactor the logic into a form that can be modified to preserve those lock bits. Add a new filesystem flag FS_USERNS_VISIBLE that requires some mount of the filesystem be fully visible in the current mount namespace, before the filesystem may be mounted. Move the logic for calling fs_fully_visible from proc and sysfs into fs/namespace.c where it has greater access to mount namespace state. Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Thomas Reitmayr authored
commit e989a73e upstream. Fix an oops during device initialization by correctly setting size_of_priv instead of leaving it 0. The regression was introduced by 8abe4a0a ("[media] dib7000: export just one symbol") and only fixed for one type of dib0700 based devices in 9e334c75 ("[media] Fix regression in some dib0700 based devices"). Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=92301 Fixes: 8abe4a0a ("[media] dib7000: export just one symbol") Signed-off-by:
Thomas Reitmayr <treitmayr@devbase.at> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Axel Lin authored
commit ebb6ad73 upstream. VMID Control 0 BIT[2:1] is VMID Divider Enable and Select 00 = VMID disabled (for OFF mode) 01 = 2 x 50kΩ divider (for normal operation) 10 = 2 x 250kΩ divider (for low power standby) 11 = 2 x 5kΩ divider (for fast start-up) So WM8903_VMID_RES_250K should be 2 << 1, which is 4. Signed-off-by:
-
Axel Lin authored
commit 14ba3ec1 upstream. According to the datasheet: R10 (0Ah) VMID Impedance Control BIT 3:2 VMIDSEL DEFAULT 00 DESCRIPTION: VMID impedance selection control 00: 75kΩ output 01: 300kΩ output 10: 2.5kΩ output WM8737_VMIDSEL_MASK is 0xC (VMIDSEL - [3:2]), so it needs to left shift WM8737_VMIDSEL_SHIFT bits for setting these bits. Signed-off-by:
-
Axel Lin authored
commit 63781394 upstream. request_any_context_irq() returns a negative value on failure. It returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED on success. So fix testing return value of request_any_context_irq(). Also fixup the return value of devm_request_any_context_irq() to make it consistent with request_any_context_irq(). Fixes: 0668d306 ("genirq: Add devm_request_any_context_irq()") Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Link: http://lkml.kernel.org/r/1431334978.17783.4.camel@ingics.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Horia Geant? authored
commit 69d9cd8c upstream. This reverts commit 7291a932. The conversion to be16_add_cpu() is incorrect in case cryptlen is negative due to premature (i.e. before addition / subtraction) implicit conversion of cryptlen (int -> u16) leading to sign loss. Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
Horia Geanta <horia.geanta@freescale.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Horia Geant? authored
commit 5fa7dadc upstream. Fixes: 1d11911a ("crypto: talitos - fix warning: 'alg' may be used uninitialized in this function") Signed-off-by:
-
Grygorii Strashko authored
commit 084609bf upstream. Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of hibernation callbacks means those pm functions will not be called upon hibernation - that leads to system crash on ARM during freezing if gpio-led is used in combination with CPU led trigger. It may happen after freeze_noirq stage (GPIO is suspended) and before syscore_suspend stage (CPU led trigger is suspended) - usually when disable_nonboot_cpus() is called. Log: PM: noirq freeze of devices complete after 1.425 msecs Disabling non-boot CPUs ... ^ system may crash or stuck here with message (TI AM572x) WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370() 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access CPU1: shutdown ^ or here Fix this by using SIMPLE_DEV_PM_OPS, which appropriately assigns the suspend and hibernation callbacks and move led_suspend/led_resume under CONFIG_PM_SLEEP to avoid build warnings. Fixes: 73e1ab41 (leds: Convert led class driver from legacy pm ops to dev_pm_ops) Signed-off-by:
Grygorii Strashko <Grygorii.Strashko@linaro.org> Acked-by:
Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by:
-
Joe Konno authored
commit 0dd23f94 upstream. Commit 007bea09 (intel_pstate: Add setting voltage value for baytrail P states.) introduced byt_set_pstate() with the assumption that it would always be run by the CPU whose MSR is to be written by it. It turns out, however, that is not always the case in practice, so modify byt_set_pstate() to enforce the MSR write done by it to always happen on the right CPU. Fixes: 007bea09 (intel_pstate: Add setting voltage value for baytrail P states.) Signed-off-by:
Joe Konno <joe.konno@intel.com> Acked-by:
Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by:
-
David Härdeman authored
commit 4d298b85 upstream. commit af3a4a9b ("[media] dib0700: NEC scancode cleanup") cleaned up the NEC scancode logic but overlooked the RC5 case. This patch brings the RC5 case in line with the NEC code and makes the struct self-documenting. Signed-off-by:
David Härdeman <david@hardeman.nu> Reported-by:
David Cimbůrek <david.cimburek@gmail.com> Signed-off-by:
-
Brian Norris authored
commit 073db4a5 upstream. On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to mtd->usecount were done without taking mtd_table_mutex. kernel: Call Trace: kernel: [<ffffffff80401818>] __put_mtd_device+0x20/0x50 kernel: [<ffffffff804086f4>] blktrans_release+0x8c/0xd8 kernel: [<ffffffff802577e0>] __blkdev_put+0x1a8/0x200 kernel: [<ffffffff802579a4>] blkdev_close+0x1c/0x30 kernel: [<ffffffff8022006c>] __fput+0xac/0x250 kernel: [<ffffffff80171208>] task_work_run+0xd8/0x120 kernel: [<ffffffff8012c23c>] work_notifysig+0x10/0x18 kernel: kernel: Code: 2442ffff ac8202d8 000217fe <00020336> dc820128 10400003 00000000 0040f809 00000000 kernel: ---[ end trace 080fbb4579b47a73 ]--- Fixed by taking the mutex in blktrans_open and blktrans_release. Note that this locking is already suggested in include/linux/mtd/blktrans.h: struct mtd_blktrans_ops { ... /* Called with mtd_table_mutex held; no race with add/remove */ int (*open)(struct mtd_blktrans_dev *dev); void (*release)(struct mtd_blktrans_dev *dev); ... }; But we weren't following it. Originally reported by (and patched by) Zhang and Giuseppe, independently. Improved and rewritten. Reported-by:
Zhang Xingcai <zhangxingcai@huawei.com> Reported-by:
Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Tested-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Martin Sperl authored
commit 8e76ef88 upstream. Fix a race (with some kernel configurations) where a queued master->pump_messages runs and frees dummy_tx/rx before spi_unmap_msg is running (or is finished). This results in the following messages: BUG: Bad page state in process page:db7ba030 count:0 mapcount:0 mapping: (null) index:0x0 flags: 0x200(arch_1) page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set ... Reported-by:
Noralf Trønnes <noralf@tronnes.org> Suggested-by:
Martin Sperl <kernel@martin.sperl.org> Signed-off-by:
-
Liu Ying authored
commit 2fa3b4c4 upstream. The LCDIF engines embedded in i.MX6sl and i.MX6sx SoCs need the axi clock as the engine's system clock. The clock should be enabled when accessing LCDIF registers, otherwise the kernel would hang up. We should also keep the clock enabled when the engine is being active to scan out frames from memory. This patch makes sure the axi clock is enabled when accessing registers so that the kernel hang up issue can be fixed. Reported-by:
Peter Chen <peter.chen@freescale.com> Tested-by:
Liu Ying <Ying.Liu@freescale.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Antonio Ospite authored
commit 61e2c70d upstream. This id has been seen in the DSDT of the Teclast X98 Air 3G tablet based on Intel Bay Trail. Signed-off-by:
Antonio Ospite <ao2@ao2.it> Cc: Bastien Nocera <hadess@hadess.net> Reviewed-by:
Daniel Baluta <daniel.baluta@intel.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Dmitry Osipenko authored
commit 4d48edb3 upstream. Commit 7232398a ("ARM: tegra: Convert PMC to a driver") changed tegra_resume() location storing from late to early and, as a result, broke suspend on Tegra20. PMC scratch register 41 is used by tegra LP1 resume code for retrieving stored physical memory address of common resume function and in the same time used by tegra20_cpu_shutdown() (shared by Tegra20 cpuidle driver and platform SMP code), which is storing CPU1 "resettable" status. It implies strict order of scratch register usage, otherwise resume function address is lost on Tegra20 after disabling non-boot CPU's on suspend. Fix it by storing "resettable" status in IRAM instead of PMC scratch register. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Fixes: 7232398a (ARM: tegra: Convert PMC to a driver) Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Pawel Moll authored
commit a18f8e97 upstream. Events defined as watchpoints on nodes must have their config values converted so that they apply to the respective node's XP. The function setting new values was using wrong mask for the "port" field, resulting in corrupted value. Fixed now. Signed-off-by:
Pawel Moll <pawel.moll@arm.com> Signed-off-by:
-
Hans Verkuil authored
commit 2b4fd3ed upstream. The cx18 PCM video device didn't have any capabilities set, which caused a warnings in the v4l2 core: [ 6.229393] ------------[ cut here ]------------ [ 6.229414] WARNING: CPU: 1 PID: 593 at drivers/media/v4l2-core/v4l2-ioctl.c:1025 v4l_querycap+0x41/0x70 [videodev]() [ 6.229415] Modules linked in: cx18_alsa mxl5005s s5h1409 tuner_simple tuner_types cs5345 tuner intel_rapl iosf_mbi x86_pkg_temp_thermal coretemp raid1 snd_hda_codec_realtek kvm_intel snd_hda_codec_generic snd_hda_codec_hdmi kvm snd_oxygen(+) snd_hda_intel snd_oxygen_lib snd_hda_controller snd_hda_codec snd_mpu401_uart iTCO_wdt snd_rawmidi iTCO_vendor_support snd_hwdep crct10dif_pclmul crc32_pclmul crc32c_intel snd_seq cx18 snd_seq_device ghash_clmulni_intel videobuf_vmalloc tveeprom cx2341x snd_pcm serio_raw videobuf_core vfat dvb_core fat v4l2_common snd_timer videodev snd lpc_ich i2c_i801 joydev mfd_core mei_me media soundcore tpm_infineon soc_button_array tpm_tis mei shpchp tpm nfsd auth_rpcgss nfs_acl lockd grace sunrpc binfmt_misc i915 nouveau mxm_wmi wmi e1000e ttm i2c_algo_bit drm_kms_helper [ 6.229444] drm ptp pps_core video [ 6.229446] CPU: 1 PID: 593 Comm: v4l_id Not tainted 3.19.3-200.fc21.x86_64 #1 [ 6.229447] Hardware name: Gigabyte Technology Co., Ltd. Z87-D3HP/Z87-D3HP-CF, BIOS F6 01/20/2014 [ 6.229448] 0000000000000000 00000000d12b1131 ffff88042dacfc28 ffffffff8176e215 [ 6.229449] 0000000000000000 0000000000000000 ffff88042dacfc68 ffffffff8109bc1a [ 6.229451] ffffffffa0594000 ffff88042dacfd90 0000000000000000 ffffffffa04e2140 [ 6.229452] Call Trace: [ 6.229466] [<ffffffff8176e215>] dump_stack+0x45/0x57 [ 6.229469] [<ffffffff8109bc1a>] warn_slowpath_common+0x8a/0xc0 [ 6.229472] [<ffffffff8109bd4a>] warn_slowpath_null+0x1a/0x20 [ 6.229474] [<ffffffffa04ca401>] v4l_querycap+0x41/0x70 [videodev] [ 6.229477] [<ffffffffa04ca6cc>] __video_do_ioctl+0x29c/0x320 [videodev] [ 6.229479] [<ffffffff81227131>] ? do_last+0x2f1/0x1210 [ 6.229491] [<ffffffffa04cc776>] video_usercopy+0x366/0x5d0 [videodev] [ 6.229494] [<ffffffffa04ca430>] ? v4l_querycap+0x70/0x70 [videodev] [ 6.229497] [<ffffffffa04cc9f5>] video_ioctl2+0x15/0x20 [videodev] [ 6.229499] [<ffffffffa04c6794>] v4l2_ioctl+0x164/0x180 [videodev] [ 6.229501] [<ffffffff8122e298>] do_vfs_ioctl+0x2f8/0x500 [ 6.229502] [<ffffffff8122e521>] SyS_ioctl+0x81/0xa0 [ 6.229505] [<ffffffff81774a09>] system_call_fastpath+0x12/0x17 [ 6.229506] ---[ end trace dacd80d4b19277ea ]--- Added the necessary capabilities to stop this warning. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Reported-by:
Laura Abbott <labbott@redhat.com> Signed-off-by:
-
Hans Verkuil authored
commit 534bc3e2 upstream. Fix the VIDIOC_QUERYCAP warning due to the missing device_caps. Don't fill in the version field, the V4L2 core will do that for you. Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 82e3b88b upstream. The maximum size for a DiSEqC command is 6, according to the userspace API. However, the code allows to write up much more values: drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23 Signed-off-by:
-
Mauro Carvalho Chehab authored
commit d7b76c91 upstream. If userspace sends an invalid bandwidth, it should either return EINVAL or switch to auto mode. This driver will go past an array and program the hardware on a wrong way if this happens. Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 1fa2337a upstream. The maximum size for a DiSEqC command is 6, according to the userspace API. However, the code allows to write up much more values: drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23 Signed-off-by:
-
