In systems where there is no hardware signal from the processor to the
PMIC to initiate the final power off sequence we must initiate the
shutdown with a register write to the PMIC. Support such systems in the
driver. Since this may prevent a full shutdown of the system platform
data is used to enable the feature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The codec for Devkit8000 (TWL4030)  was not detected except
when build with CONFIG_SND_SOC_ALL_CODECS.

twl-core.c still uses the CONFIG_TWL4030_CODEC for
twl_has_codec().

In commit 57fe7251
the CONFIG_TWL4030_CODEC was renamed
into CONFIG_MFD_TWL4030_AUDIO, thatswhy the codec
was not detected.

This patch renames the CONFIG_ TWL4030_CODEC into
CONFIG_MFD_TWL4030_AUDIO in twl-core.c.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We currently have two symbols to control compilation the MFD subsystem,
MFD_SUPPORT and MFD_CORE. The MFD_SUPPORT is actually not required
at all, it only hides the submenu when not set, with the effect that
Kconfig warns about missing dependencies when another driver selects
an MFD driver while MFD_SUPPORT is disabled. Turning the MFD submenu
back from menuconfig into a plain menu simplifies the Kconfig syntax
for those kinds of users and avoids the surprise when the menu
suddenly appears because another driver was enabled that selects this
symbol.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Now that all in-tree users are fixed to use the more general mc13xxx API
the obsolete stuff can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The mc13783_... functions are going to be removed, so switch to the
more generic API.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The latter constants are going to be removed in favour of the former
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This is the first step to also support the touch interface of the mc13892
pmic chip.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This is needed to convert the touch driver away from using struct mc13783.

Note this patch drops MC13783_ADC0_ADREFMODE. This is unused and doesn't
exist on mc13892.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

mc13xxx is the more general API and most of the mc13783_... functions
are going to die.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Threads from twl4030's children will be called
nested in the context of the demultiplexing
handler on twl4030-irq.c.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

... and do all the synchronization with the
hardware during bus_sync_unlock. We can now
remove all the workqueues.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

... we can do the synchronization with the
hardware when calling bus_sync_unlock as
we're supposed to. While at that, also make
variable names uniform on all functions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

... and use threaded IRQ infrastructure. Later
patches will come dropping both workqueues and
setting the nested thread flag.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

For doing that, drop the locking and change that
to a mutex.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

trivial patch, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

- Support wake-up from suspend-to-ram.
- Handle pending interrupt after a resume.
- If pdata->wakeup is enabled, by default, the device is assumed to be
capable of wakeup (the interrupt pin is connected to a wakeup-source GPIO)
and may wakeup the system (MAX8997 has a power button input pin).
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Enhancements to the WM8994 audio driver and new features on more modern
devices in the series mean that we can no longer rely on VMID being active
as an indication that the device is active. Add further checks for digital
paths and microphone detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Kyle Manna <kyle@kylemanna.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Without turning the MADC clock on, no MADC conversions occur.

$ cat /sys/class/hwmon/hwmon0/device/in8_input
[   53.428436] twl4030_madc twl4030_madc: conversion timeout!
cat: read error: Resource temporarily unavailable
Signed-off-by: Kyle Manna <kyle@kylemanna.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In systems where the LDO enables are always driven (for example, being
connected to an always on supply rail or a GPIO which is driven by the
CPU even in suspend) then we can disable the pull downs on the LDO for
a small power savings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

I was trying to fix the error handling part because in the case of
request_irq failure, it should call kthread_stop instead of free_irq.
But it seems more reasonable to do request_irq before calling kthread_run.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Refactor the GPADC interface to avoid bugs in calling code:

- ab8500_gpadc_[convert|read_raw|ad_to_voltage] clarifies
  each functions use case, *convert wraps *read_raw, and we
  can access raw ADC values properly.
- Renamed gpadc function arguments from "input" to "channel" to
  clarify use, so we don't get confused again.
Signed-off-by: Kalle Komierowski <kalle.komierowski@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Reviewed-by: John Beckett <john.beckett@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In the first three cases, ioremap has been called, so iounmap is needed.  A
new label for this is introduced, to differentiate it from err_msix, which
is the first point at which msix_entries actually needs to be freed.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The CONFIG_PM code was unconditionally compiled in despite
the dev_pm_ops only being included into the driver struct
if used. Fix this by adding the missing #ifdef.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Defined the gpio_chip label in the mfd/asic3 driver for diagnostics.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The return value of asic3_clk_enable() was neither used nor useful. So let's
make it a void function, and thereby match asic3_clk_disable().
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Added led suspend/resume handlers to the leds/leds-asic3 and mfd/asic3 drivers.
On suspend the leds will be turned off and their clocks disabled. On resume the
reverse.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The mfd/asic3 driver did not define the suspend/resume handlers for the mmc cell
driver. Consequently the mmc driver did not resume properly after returning from
suspend, making sd cards unusable and preventing suspend from being entered a
second time. This patch adds the suspend/resume handlers, fixing the problem.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

More annoying than usual as they're in the middle of a function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch fixes:
WARNING: drivers/mfd/built-in.o(.data+0x9998): Section mismatch in reference from the variable ab3550_driver to the function .init.text:ab3550_probe()
The variable ab3550_driver references
the function __init ab3550_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

* git://git.infradead.org/iommu-2.6:
  intel-iommu: fix superpage support in pfn_to_dma_pte()
  intel-iommu: set iommu_superpage on VM domains to lowest common denominator
  intel-iommu: fix return value of iommu_unmap() API
  MAINTAINERS: Update VT-d entry for drivers/pci -> drivers/iommu move
  intel-iommu: Export a flag indicating that the IOMMU is used for iGFX.
  intel-iommu: Workaround IOTLB hang on Ironlake GPU
  intel-iommu: Fix AB-BA lockdep report

* 'for-linus' of http://people.redhat.com/agk/git/linux-dm:
  dm kcopyd: fix job_pool leak

Commit 4b239f45 ("x86-64, mm: Put early page table high") causes a S4
regression since 2.6.39, namely the machine reboots occasionally at S4
resume.  It doesn't happen always, overall rate is about 1/20.  But,
like other bugs, once when this happens, it continues to happen.

This patch fixes the problem by essentially reverting the memory
assignment in the older way.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yinghai.lu@oracle.com>
[ We'll hopefully find the real fix, but that's too late for 3.1 now ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix memory leak introduced by commit a6e50b40
(dm snapshot: skip reading origin when overwriting complete chunk).

When allocating a set of jobs from kc->job_pool, job->master_job must be
set (to point to itself) so that the mempool item gets freed when the
master_job completes.

master_job was introduced by commit c6ea41fb
(dm kcopyd: preallocate sub jobs to avoid deadlock)
Reported-by: Michael Leun <ml@newton.leun.net>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

* 'samsung-fixes-4' of git://github.com/kgene/linux-samsung:
  ARM: S3C24XX: Fix s3c24xx build errors if !CONFIG_PM
  ARM: S5P: fix offset calculation on gpio-interrupt

Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (w83627ehf) Fix negative 8-bit temperature values

v2:
- register_syscore_ops(&s3c24xx_irq_syscore_ops) does not need to be
  conditionally compiled out, it is already optimized out on !CONFIG_PM
- fix also s3c2412 and s3c2416 affected by the same build issue

v1:
s3c2440.c fails to build if !CONFIG_PM because in such case
s3c2410_pm_syscore_ops is not defined. Same error should happen also
in s3c2410.c and s3c2442.c
Signed-off-by: Domenico Andreoli <cavokz@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>