The rep legacy RQ completion handling was missing the appropriate
handling of error CQEs (dump the CQE and queue a recover work), fix it
by calling trigger_report() when needed.

Since all CQE handling flows do the exact same error CQE handling,
extract it to a common helper function.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Remove redundant and trivial error logging when trying to
offload mirred device with unsupported devices.
Using OVS could hit those a lot and the errors are still
logged in extack.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Rearrange the code and use cqe_mode_to_period_mode() helper.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Feature dependencies should be resolved in fix features rather than in
set features flow. Move the check that disables HW-GRO in case CQE
compression is enabled from set_feature_hw_gro() to
mlx5e_fix_features().
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Remove redundant space when constructing the feature's enum. Validate
against the indented enum value.

Fixes: 6c72cb05 ("net/mlx5e: Use bitmap field for profile features")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When using libvirt to passthrough VF to VM it will always set the VF vlan
to 0 even if user didn’t request it, this will cause libvirt to fail to
boot in case the PF isn't eswitch owner.

Example of such case is the DPU host PF which isn't eswitch manager, so
any attempt to passthrough VF of it using libvirt will fail.

Fix it by not returning error in case set VF vlan is called with vid 0.
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add FEC counters' statistics of corrected_blocks and
uncorrectable_blocks, along with their lanes via ethtool.

HW supports corrected_blocks and uncorrectable_blocks counters both for
RS-FEC mode and FC-FEC mode. In FC mode these counters are accumulated
per lane, while in RS mode the correction method crosses lanes, thus
only total corrected_blocks and uncorrectable_blocks are reported in
this mode.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

log_max_qp in driver's default profile #2 was set to 18, but FW actually
supports 17 at the most - a situation that led to the concerning print
when the driver is loaded:
"log_max_qp value in current profile is 18, changing to HCA capabaility
limit (17)"

The expected behavior from mlx5_profile #2 is to match the maximum FW
capability in regards to log_max_qp. Thus, log_max_qp in profile #2 is
initialized to a defined static value (0xff) - which basically means that
when loading this profile, log_max_qp value  will be what the currently
installed FW supports at most.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently all SFs are using the same CPUs. Spreading SF over CPUs, in
round-robin manner, in order to achieve better distribution of the SFs
over available CPUs.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently IRQs are requested one by one. To balance spreading IRQs
among cpus using such scheme requires remembering cpu mask for the
cpus used for a given device. This complicates the IRQ allocation
scheme in subsequent patch.

Hence, prepare the code for bulk IRQs allocation. This enables
spreading IRQs among cpus in subsequent patch.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The downstream patches add more functionality to irq_pool_affinity.
Move the irq_pool_affinity logic to a new file in order to ease the
coding and maintenance of it.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Move affinity binding of the IRQ to irq_request function in order to
bind the IRQ before inserting it to the xarray.

After this change, the IRQ is ready for use when inserted to the xarray.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, IRQ layer have a separate flow for ctrl and comp IRQs, and
the distinction between ctrl and comp IRQs is done in the IRQ layer.

In order to ease the coding and maintenance of the IRQ layer,
introduce a new API for requesting control IRQs -
mlx5_ctrl_irq_request(struct mlx5_core_dev *dev).
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Callers of this functions ignore its return value, as reported by
Wang Qing, in one of the return paths, it returns positive values.

Since return value is ignored anyways, void out the return type of the
function.
Reported-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Laurent reported that they have seen a significant amount of TCP retransmissions
at high throughput from applications residing in network namespaces talking to
the outside world via veths. The drops were seen on the qdisc layer (fq_codel,
as per systemd default) of the phys device such as ena or virtio_net due to all
traffic hitting a _single_ TX queue _despite_ multi-queue device. (Note that the
setup was _not_ using XDP on veths as the issue is generic.)

More specifically, after edbea922 ("veth: Store queue_mapping independently
of XDP prog presence") which made it all the way back to v4.19.184+,
skb_record_rx_queue() would set skb->queue_mapping to 1 (given 1 RX and 1 TX
queue by default for veths) instead of leaving at 0.

This is eventually retained and callbacks like ena_select_queue() will also pick
single queue via netdev_core_pick_tx()'s ndo_select_queue() once all the traffic
is forwarded to that device via upper stack or other means. Similarly, for others
not implementing ndo_select_queue() if XPS is disabled, netdev_pick_tx() might
call into the skb_tx_hash() and check for prior skb_rx_queue_recorded() as well.

In general, it is a _bad_ idea for virtual devices like veth to mess around with
queue selection [by default]. Given dev->real_num_tx_queues is by default 1,
the skb->queue_mapping was left untouched, and so prior to edbea922 the
netdev_core_pick_tx() could do its job upon __dev_queue_xmit() on the phys device.

Unbreak this and restore prior behavior by removing the skb_record_rx_queue()
from veth_xmit() altogether.

If the veth peer has an XDP program attached, then it would return the first RX
queue index in xdp_md->rx_queue_index (unless configured in non-default manner).
However, this is still better than breaking the generic case.

Fixes: edbea922 ("veth: Store queue_mapping independently of XDP prog presence")
Fixes: 638264dc ("veth: Support per queue XDP ring")
Reported-by: Laurent Bernaille <laurent.bernaille@datadoghq.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Cc: Toshiaki Makita <toshiaki.makita1@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are currently 2 ways to create a set of sysfs files for a
kobj_type, through the default_attrs field, and the default_groups
field.  Move the ibmveth sysfs code to use default_groups
field which has been the preferred way since aa30f47c ("kobject: Add
support for default attribute groups to kobj_type") so that we can soon
get rid of the obsolete default_attrs field.

Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Cristobal Forno <cforno12@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean the following coccicheck warning:

./drivers/net/ethernet/sfc/efx_channels.c:870:36-37: WARNING opportunity
for swap().

./drivers/net/ethernet/sfc/efx_channels.c:824:36-37: WARNING opportunity
for swap().
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ethtool_get_phy_stats(), the phydev varaible is set to
dev->phydev but dev->phydev is still used.  Replace
dev->phydev uses with phydev.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs.

We must use separate phylink_pcs instances for the USX and SGMII PCS,
rather than just changing the "ops" pointer before re-setting it to
phylink as this interface queries the PCS, rather than requesting it
to be changed.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet suggested to allow users to modify max GRO packet size.

We have seen GRO being disabled by users of appliances (such as
wifi access points) because of claimed bufferbloat issues,
or some work arounds in sch_cake, to split GRO/GSO packets.

Instead of disabling GRO completely, one can chose to limit
the maximum packet size of GRO packets, depending on their
latency constraints.

This patch adds a per device gro_max_size attribute
that can be changed with ip link command.

ip link set dev eth0 gro_max_size 16000
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Coco Li <lixiaoyan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When multiple sockets using the SOF_TIMESTAMPING_BIND_PHC flag received
a packet with a hardware timestamp (e.g. multiple PTP instances in
different PTP domains using the UDPv4/v6 multicast or L2 transport),
the timestamps received on some sockets were corrupted due to repeated
conversion of the same timestamp (by the same or different vclocks).

Fix ptp_convert_timestamp() to not modify the shared skb timestamp
and return the converted timestamp as a ktime_t instead. If the
conversion fails, return 0 to not confuse the application with
timestamps corresponding to an unexpected PHC.

Fixes: d7c08826 ("net: socket: support hardware timestamp conversion to PHC bound")
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As discussed during review here:
https://patchwork.kernel.org/project/netdevbpf/patch/20220105132141.2648876-3-vladimir.oltean@nxp.com/

we should inform developers about pitfalls of concurrent access to the
boolean properties of dsa_switch and dsa_port, now that they've been
converted to bit fields. No other measure than a comment needs to be
taken, since the code paths that update these bit fields are not
concurrent with each other.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a cosmetic incremental fixup to commits
7787ff77 ("net: dsa: merge all bools of struct dsa_switch into a single u32")
bde82f38 ("net: dsa: merge all bools of struct dsa_port into a single u8")

The desire to make this change was enunciated after posting these
patches here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220105132141.2648876-1-vladimir.oltean@nxp.com/

but due to a slight timing overlap (message posted at 2:28 p.m. UTC,
merge commit is at 2:46 p.m. UTC), that comment was missed and the
changes were applied as-is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
DSA initialization cleanups

These patches contain miscellaneous work that makes the DSA init code
path symmetric with the teardown path, and some additional patches
carried by Ansuel Smith for his register access over Ethernet work, but
those patches can be applied as-is too.
https://patchwork.kernel.org/project/netdevbpf/patch/20211214224409.5770-3-ansuelsmth@gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It is said that as soon as a network interface is registered, all its
resources should have already been prepared, so that it is available for
sending and receiving traffic. One of the resources needed by a DSA
slave interface is the master.

dsa_tree_setup
-> dsa_tree_setup_ports
   -> dsa_port_setup
      -> dsa_slave_create
         -> register_netdevice
-> dsa_tree_setup_master
   -> dsa_master_setup
      -> sets up master->dsa_ptr, which enables reception

Therefore, there is a short period of time after register_netdevice()
during which the master isn't prepared to pass traffic to the DSA layer
(master->dsa_ptr is checked by eth_type_trans). Same thing during
unregistration, there is a time frame in which packets might be missed.

Note that this change opens us to another race: dsa_master_find_slave()
will get invoked potentially earlier than the slave creation, and later
than the slave deletion. Since dp->slave starts off as a NULL pointer,
the earlier calls aren't a problem, but the later calls are. To avoid
use-after-free, we should zeroize dp->slave before calling
dsa_slave_destroy().

In practice I cannot really test real life improvements brought by this
change, since in my systems, netdevice creation races with PHY autoneg
which takes a few seconds to complete, and that masks quite a few races.
Effects might be noticeable in a setup with fixed links all the way to
an external system.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit a57d8c21 ("net: dsa: flush switchdev workqueue before
tearing down CPU/DSA ports"), the port setup and teardown procedure
became asymmetric.

The fact of the matter is that user ports need the shared ports to be up
before they can be used for CPU-initiated termination. And since we
register net devices for the user ports, those won't be functional until
we also call the setup for the shared (CPU, DSA) ports. But we may do
that later, depending on the port numbering scheme of the hardware we
are dealing with.

It just makes sense that all shared ports are brought up before any user
port is. I can't pinpoint any issue due to the current behavior, but
let's change it nonetheless, for consistency's sake.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA needs to simulate master tracking events when a binding is first
with a DSA master established and torn down, in order to give drivers
the simplifying guarantee that ->master_state_change calls are made
only when the master's readiness state to pass traffic changes.
master_state_change() provide a operational bool that DSA driver can use
to understand if DSA master is operational or not.
To avoid races, we need to block the reception of
NETDEV_UP/NETDEV_CHANGE/NETDEV_GOING_DOWN events in the netdev notifier
chain while we are changing the master's dev->dsa_ptr (this changes what
netdev_uses_dsa(dev) reports).

The dsa_master_setup() and dsa_master_teardown() functions optionally
require the rtnl_mutex to be held, if the tagger needs the master to be
promiscuous, these functions call dev_set_promiscuity(). Move the
rtnl_lock() from that function and make it top-level.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At present there are two paths for changing the MTU of the DSA master.

The first is:

dsa_tree_setup
-> dsa_tree_setup_ports
   -> dsa_port_setup
      -> dsa_slave_create
         -> dsa_slave_change_mtu
            -> dev_set_mtu(master)

The second is:

dsa_tree_setup
-> dsa_tree_setup_master
   -> dsa_master_setup
      -> dev_set_mtu(dev)

So the dev_set_mtu() call from dsa_master_setup() has been effectively
superseded by the dsa_slave_change_mtu(slave_dev, ETH_DATA_LEN) that is
done from dsa_slave_create() for each user port. The later function also
updates the master MTU according to the largest user port MTU from the
tree. Therefore, updating the master MTU through a separate code path
isn't needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently dsa_slave_create() has two sequences of rtnl_lock/rtnl_unlock
in a row. Remove the rtnl_unlock() and rtnl_lock() in between, such that
the operation can execute slighly faster.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In dsa_slave_create() there are 2 sections that take rtnl_lock():
MTU change and netdev registration. They are separated by PHY
initialization.

There isn't any strict ordering requirement except for the fact that
netdev registration should be last. Therefore, we can perform the MTU
change a bit later, after the PHY setup. A future change will then be
able to merge the two rtnl_lock sections into one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2022-01-06

1) Fix some clang_analyzer warnings about never read variables.
   From luo penghao.

2) Check for pols[0] only once in xfrm_expand_policies().
   From Jean Sacren.

3) The SA curlft.use_time was updated only on SA cration time.
   Update whenever the SA is used. From Antony Antony

4) Add support for SM3 secure hash.
   From Xu Jia.

5) Add support for SM4 symmetric cipher algorithm.
   From Xu Jia.

6) Add a rate limit for SA mapping change messages.
   From Antony Antony.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Aleksander Jan Bajkowski says:

====================
net: lantiq_xrx200: improve ethernet performance

This patchset improves Ethernet performance by 15%.

NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):

	Down		Up
Before	539 Mbps	599 Mbps
After	624 Mbps	695 Mbps
====================

Link: https://lore.kernel.org/r/20220104151144.181736-1-olek2@wp.plSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We can increase the efficiency of rx path by using buffers to receive
packets then build SKBs around them just before passing into the network
stack. In contrast, preallocating SKBs too early reduces CPU cache
efficiency.

NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):

	Down		Up
Before	577 Mbps	648 Mbps
After	624 Mbps	695 Mbps
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):

	Down		Up
Before	545 Mbps	625 Mbps
After	577 Mbps	648 Mbps
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):

	Down		Up
Before	539 Mbps	599 Mbps
After	545 Mbps	625 Mbps
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When the -L option of the testptp utility is specified with other
options (e.g. -p to enable PPS output), the user probably wants to
apply it to the pin configured by the -L option.

Reorder the code to set the pin function before other function requests
to avoid confusing users.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20220105152506.3256026-1-mlichvar@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski"
 "Networking fixes, including fixes from bpf, and WiFi. One last pull
  request, turns out some of the recent fixes did more harm than good.

  Current release - regressions:

   - Revert "xsk: Do not sleep in poll() when need_wakeup set", made the
     problem worse

   - Revert "net: phy: fixed_phy: Fix NULL vs IS_ERR() checking in
     __fixed_phy_register", broke EPROBE_DEFER handling

   - Revert "net: usb: r8152: Add MAC pass-through support for more
     Lenovo Docks", broke setups without a Lenovo dock

  Current release - new code bugs:

   - selftests: set amt.sh executable

  Previous releases - regressions:

   - batman-adv: mcast: don't send link-local multicast to mcast routers

  Previous releases - always broken:

   - ipv4/ipv6: check attribute length for RTA_FLOW / RTA_GATEWAY

   - sctp: hold endpoint before calling cb in
     sctp_transport_lookup_process

   - mac80211: mesh: embed mesh_paths and mpp_paths into
     ieee80211_if_mesh to avoid complicated handling of sub-object
     allocation failures

   - seg6: fix traceroute in the presence of SRv6

   - tipc: fix a kernel-infoleak in __tipc_sendmsg()"

* tag 'net-5.16-final' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (36 commits)
  selftests: set amt.sh executable
  Revert "net: usb: r8152: Add MAC passthrough support for more Lenovo Docks"
  sfc: The RX page_ring is optional
  iavf: Fix limit of total number of queues to active queues of VF
  i40e: Fix incorrect netdev's real number of RX/TX queues
  i40e: Fix for displaying message regarding NVM version
  i40e: fix use-after-free in i40e_sync_filters_subtask()
  i40e: Fix to not show opcode msg on unsuccessful VF MAC change
  ieee802154: atusb: fix uninit value in atusb_set_extended_addr
  mac80211: mesh: embedd mesh_paths and mpp_paths into ieee80211_if_mesh
  mac80211: initialize variable have_higher_than_11mbit
  sch_qfq: prevent shift-out-of-bounds in qfq_init_qdisc
  netrom: fix copying in user data in nr_setsockopt
  udp6: Use Segment Routing Header for dest address if present
  icmp: ICMPV6: Examine invoking packet for Segment Route Headers.
  seg6: export get_srh() for ICMP handling
  Revert "net: phy: fixed_phy: Fix NULL vs IS_ERR() checking in __fixed_phy_register"
  ipv6: Do cleanup if attribute validation fails in multipath route
  ipv6: Continue processing multipath route even if gateway attribute is invalid
  net/fsl: Remove leftover definition in xgmac_mdio
  ...

The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.

However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Russell King says:

====================
Fix RGMII delays for 88E1118

This series fixes the RGMII delays for 88E1118 Marvell PHYs, after
a report by Corentin Labbe that the Marvell driver fails to work.

Patch 1 cleans up the paged register accesses in m88e1118_config_init()
and patch 2 adds the RGMII delay configuration.

This comes with an element of risk as existing DT may need to be fixed
for this in a similar way as we have done in the recent past for other
PHY drivers that have misinterpreted the RGMII interface modes.
====================

Link: https://lore.kernel.org/r/YdR3wYFkm4eJApwb@shell.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>