In most cases, when EH is scheduled, all in-flight commands are
aborted causing EH to kick in immediately.  However, in some cases
(especially with PMP), it's unclear which commands are affected by the
error condition and although aborting all in-flight commands work, it
isn't optimal and may cause unnecessary disruption.  On the other
hand, waiting for in-flight commands to drain themselves can take up
to 30seconds.

This patch implements EH fast drain to handle such situations.  It
gives in-flight commands some time to finish up but doesn't wait for
too long.  After EH is scheduled, fast drain timer is started and if
no other completion occurs in ATA_EH_FASTDRAIN_INTERVAL all in-flight
commands are aborted.  If any completion occurred in the interval, the
port is given another interval to finish up itself.

Currently ATA_EH_FASTDRAIN_INTERVAL is 3 secs which should be enough
for finishing up most commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

If SError isn't accessible, EH can't tell whether hotplug has happened
or not.  Report SError read failure with AC_ERR_OTHER and schedule
probing with hardreset.  This will be mainly useful for PMPs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ATA_EHI_HOTPLUGGED is a hint for reset functions indicating the the
port might have gone through hotplug/unplug just before entering EH.
Reset functions modify their behaviors a bit to handle the situation
better - e.g. using longer debouncing delay.

Currently, once HOTPLUG is set, it isn't cleared till the end of EH.
This is unnecessary and makes EH take longer.  Clear the HOTPLUGGED
flag after a reset try (successful or not).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

__ata_ehi_hotplugged() now has no users.  Regorganize
ata_ehi_hotplugged() such that a new function ata_ehi_schedule_probe()
deals with scheduling probing.  ata_ehi_hotplugged() calls it and
additionally marks hotplug specific flags.  ata_ehi_schedule_probe()
will be used laster.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

SCSI scan may fail due to memory allocation failure even if EH is not
in progress.  Due to use of GFP_ATOMIC in SCSI scan path, allocation
failure isn't too rare especially while probing multiple devices at
once which is the case when a bunch of devices are connected to PMP.

This patch moves SCSI scan failure detetion logic from
ata_scsi_hotplug() to ata_scsi_scan_host() and implement synchronous
scan behavior.  The synchronous path sleeps briefly and repeats SCSI
scan if some devices aren't attached properly.  It contains robust
retry loop to minimize the chance of device misdetection during boot
and falls back to async retry if everything fails.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Debouncing failure is a good indicator of basic link problem.  Use
-EPIPE to indicate debouncing failure and make ata_eh_reset() invoke
sata_down_spd_limit() if the error occurs during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sata_down_spd_limit() first reads the current SPD from SStatus and
limit the speed to the lower one of one below the current limit or one
below the current SPD in SStatus.  SPD may not be accessible or valid
when SPD down is requested making sata_down_spd_limit() fail when it's
most needed.

This patch makes the current SPD cached after each successful reset
and forces GEN I speed (1.5Gbps) if neither of SStatus or the cached
value is valid, so sata_down_spd_limit() is now guaranteed to lower
the speed limit if lower speed is available.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

the onchip SATA type set in the system BIOS:
Device                              Device ID
SATA in IDE mode             0x4390
SATA in AHCI mode           0x4391
SATA in non-raid5 driver     0x4392
SATA in raid5 driver           0x4393

Although the device ID is different, they use the same AHCI driver
.The attached file is the patch for adding these device
IDs for ATI SB700.

Signed-off-by: henry.su.ati@gmail.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Make ahci_scr_read/write() handle SCR_NOTIFICATION if the controller
supports it.  Also, print "sntf" in the cap line if supported.

While at it, convert eight space into a tab in ahci_print_info().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ahci_save_initial_config() is responsible for reading, screening the
host CAP register and storing the modified result into hpriv->cap for
the rest of the driver.  Move ATA_FLAG_NO_NCQ handling into
ahci_save_initial_config().  It's more consistent this way and the
rest of the driver can always refer to hpriv->cap to determine
configured capability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Convert ->scr_read/write callbacks to return error code to better
indicate failure.  This will help handling of SCR_NOTIFICATION.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

When an NCQ command fails, all commands in flight are aborted and the
offending one is reported using log page 10h.  Depending on controller
characteristics and LLD implementation, all commands may appear as
having a device error due to shared TF status making it hard to
determine what's actually going on.

This patch adds AC_ERR_NCQ, marks the command reported by log page 10h
with it and print extra "<F>" after the error report for the command
to help distinguishing the offending command.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Requiring LLDs to format multiple error description messages properly
doesn't work too well.  Help LLDs a bit by making ata_ehi_push_desc()
insert ", " on each invocation.  __ata_ehi_push_desc() is the raw
version without the automatic separator.

While at it, make ehi_desc interface proper functions instead of
macros.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out sil24_do_softreset() which takes @pmp as its last
argument.  This will be used to implement sil24_pmp_softreset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out sil24_exec_polled_cmd() from sil24_softreset().  This
will be used to implement sil24_pmp_read/write().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Replace sil24_update_tf() to sil24_read_tf() which reads TF into
passed int result TF argument and can read TFs of PMP links.  This
will be used by PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out ahci_do_softreset() which takes @pmp as its last
argument.  This will be used to implement ahci_pmp_softreset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out ahci_exec_polled_cmd() from ahci_softreset().  This will
be used to implement ahci_pmp_read/write().  ahci_exec_polled_cmd()
performs reset_engine before returning if the command fails (times
out).  This is to improve robustness.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out stop_engine - CLO - start_engine sequence from
ahci_softreset() and ahci_clo() into ahci_reset_engine() and use it in
ahci_softreset() and ahci_post_internal_cmd().  The function will also
be used to prepare for and clean up after PMP register access
commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Use deadline instead of fixed timeout for 1st FIS for SRST to improve
robustness of SRST.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add @is_cmd to ata_tf_to_fis().  This controls bit 7 of the second
byte which tells the device whether this H2D FIS is for a command or
not.  This cleans up ahci a bit and will be used by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ata_tf_read was setting HOB bit when lba48 command was submitted, but
was not clearing it before reading "normal" data.  As it is only place
which sets HOB bit in control register, and register reads should not
be affected by other bits, let's just clear it when we are done with
reading upper bytes so non-48bit commands do not have to touch ctl
at all.

pata_scc suffered from same problem...
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The filename in the file header is incorrect.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch fixes some issues of the previous patch:
- Use mode_filter() hook to limit ATAPI UDMA mode
- "data loss" warning message
- handling of udma_mask
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Commit df69c9c5 moved only prototype of
out of CONFIG_PM. Move function out as well. Box seems to boot fine.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Yay, the first one from Seagate.  3.ALC firmware is okay.  This was
reported by Sam Freed on bugzilla bug 8759.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Sam Freed <sam@freed.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pata_platform: Fix NULL pointer dereference

pata_platform currently dereferences a NULL pointer in pata_platform_probe()
if pdev->dev.platform_data is set to NULL. This breakage was most likely
introduced by commit 5f45bc50.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* trim trailing whitespace
* document some flags, registers, and register bits
* fix locking around EDMA on/off and configuration
* continue replacing "constant OP var" with "var OP constant"
* use new pci_try_set_mwi()
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* Micro-optimization in the EDMA interrupt handling code
* s/EDMA_ERR_CRBQ_PAR/EDMA_ERR_CRQB_PAR/
* Document EDMA Error Interrupt Cause register bits
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'kmem_death' of master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6:
  mm: Remove slab destructors from kmem_cache_create().

	Change in 'kbuild: do section mismatch check on full vmlinux'
should've been replicated in arch/um/Makefile.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Slab destructors were no longer supported after Christoph's
c59def9f change. They've been
BUGs for both slab and slub, and slob never supported them
either.

This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6: (23 commits)
  ide: add support for SCSI ioctls to ide-floppy
  ide: remove stale changelog from setup-pci.c
  ide: remove stale changelog/comments/TODO from ide.c
  ide-cris: handle PIO auto-tuning in tune_cris_ide()
  ide: add PIO masks
  ide: remove ide_find_best_pio_mode()
  ide: drop "PIO data" argument from ide_get_best_pio_mode()
  ide: ide_find_best_pio_mode() fixes (take 2)
  ide: add ide_pio_cycle_time() helper (take 2)
  sc1200: remove stale Power Management code
  ide: ide_start_power_step() fix WRT disabling DMA
  serverworks: fix DMA
  serverworks: always tune PIO
  ide: add ide_pci_device_t.host_flags (take 2)
  ide: add ide_dev_has_iordy() helper (take 4)
  ide: make ide_get_best_pio_mode() print info if overriding PIO mode
  siimage: PIO mode setup fixes (take 2)
  atiixp: PIO mode setup fixes
  ide: Stop mapping ROMs
  IDE: Remove references to dead ETRAX-related variables.
  ...

	a) switch by loff_t == __cmpdi2 use.  Replaced with a couple
of obvious ifs; update of ->f_pos in the first one makes sure that we
do the right thing in all cases.
	b) block_signals() and unblock_signals() are globals on UML.
Renamed coda ones; in principle UML probably ought to do rename as
well, but that's another story.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

	Removal of rtt argument in ->cong_avoid() had missed tcp_htcp.c
instance.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Now that ide-floppy supports SG_IO we can add support for SCSI ioctls
(except deprecated SCSI_IOCTL_SEND_COMMAND and legacy CDROM_SEND_PACKET
ones - we can add them later iff really needed).

While at it remove handling of CDROMEJECT and CDROMCLOSETRAY ioctls from
generic_ide_ioctl():

- This prevents ide-{disk,tape,scsi} device drivers from obtaining
  REQ_TYPE_BLOCK_PC type requests which are currently unsupported by
  these drivers and which are potentially harmful (as reported by Andrew).

- There is no functionality loss since aforementioned ioctls will now be
  handled by idefloppy_ioctl()->scsi_cmd_ioctl() (for devices using
  ide-floppy driver) and by idecd_ioctl->cdrom_ioctl()->scsi_cmd_ioctl()
  (for devices using ide-cd driver).

Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>