- 07 Oct, 2010 13 commits
-
-
Johannes Berg authored
The core module doesn't need to carry around the code for chain settings that is used for HT drivers (agn) only. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Johannes Berg authored
There's no need to go via the indirect function call from within the 3945 subdriver. Signed-off-by:
-
Johannes Berg authored
The different drivers need to do different things after a scan, so create a post_scan hook to allow them to do this. Signed-off-by:
-
Johannes Berg authored
iwl_commit_rxon really should be named iwlagn_commit_rxon, so rename it. Signed-off-by:
-
Rajkumar Manoharan authored
The following commit removed DISABLE_REGWRITE_BUFFER ops. The unnecessary REGWRITE_BUFFER_FLUSH was not removed properly which is causing failure on hw reset. Author: Felix Fietkau <nbd@openwrt.org> Date: Tue Oct 5 12:03:42 2010 +0200 ath9k_hw: clean up register write buffering Signed-off-by:Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
There's no need for the WDS peer address to not be const, so make it const. Signed-off-by:
-
Johannes Berg authored
Bill Jordan's patch to allow setting the WDS peer crossed with my patch removing all the boilerplate code in nl80211, and consequently he didn't make use of it yet. Fix that. Signed-off-by:
-
Johannes Berg authored
The recent scan overhaul broke locking because now we can jump to code that attempts to unlock, while we don't have the mutex held. Fix this by holding the mutex around all the relevant code. Reported-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
-
Juuso Oikarinen authored
In the NVS/INI-parameters for the driver/firmware there is the FEM (front end module) selection option, which may configure the hardware FEM via autodetection or manual selection. So far, there has been support for manual selection only. Add support for FEM autodetection. Signed-off-by:
Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by:
-
John W. Linville authored
Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
-
-
John W. Linville authored
This reverts commit 5ed3bc72. It turns-out that not all drivers are calling ieee80211_tx_status from a compatible context. Revert this for now and try again later... Signed-off-by:
-
John W. Linville authored
This reverts commit 030725d2. This commit relies on commit 5ed3bc72 ("mac80211: use netif_receive_skb in ieee80211_tx_status callpath") Unfortunately not all drivers are calling ieee80211_tx_status from a compatible context, so that commit needs to be reverted in 2.6.36. Signed-off-by:
-
- 06 Oct, 2010 27 commits
-
-
Wey-Yi Guy authored
Adding MODULE_FIRMWARE define for 130 series of devices Signed-off-by: -
Wey-Yi Guy authored
130 series device should use firmware name with 130 in it. Signed-off-by: -
John W. Linville authored
net/mac80211/scan.c: In function ‘ieee80211_scan_cancel’: net/mac80211/scan.c:794: warning: ‘finish’ may be used uninitialized in this function Signed-off-by: -
Johannes Berg authored
When multiple interfaces are actively trying to associate with the same BSS, they may both find that the BSS isn't there and then try to unlink it. This can cause errors since the unlinking code can't currently deal with items that have already been unlinked. Normally this doesn't happen as most people don't try to use multiple station interfaces that associate at the same time too. Fix this by using the list entry as a flag to see if the item is still on a list. Cc: stable@kernel.org Reported-by:
Hun-Kyi Wynn <hkwynn@candelatech.com> Signed-off-by:
-
Bruno Randolf authored
This information is already available in mac80211, we just need to export it via cfg80211 and nl80211. Signed-off-by:
Bruno Randolf <br1@einfach.org> Acked-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Stanislaw Gruszka authored
This reverts commit 7acc7c68. It was applied to avoid possible warning in ieee80211_restart_hw, however reason of the warning were races in mac80211, currently hopefully fixed. Not reseting device when performing scan is bad for two reasons. When forcing reset from iwl_check_stuck_queue(), in case of fail, reset will be repeated until scan finish. But since firmware is in bad shape, scan only finish after scan_check work (about 7s). So we will delay the reset, what is not good behaviour. When forcing reset from iwl_recover_from_statistics(), we will not repeat the reset, so we will not perform reset at all when needed. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Acked-by:
-
Stanislaw Gruszka authored
We nulify local->scan_req on failure in __ieee80211_start_scan, so __ieee80211_scan_completed will not call cfg80211_scan_done. Fix that. Signed-off-by:
-
Stanislaw Gruszka authored
When performing hw scan and not abort it, __ieee80211_scan_completed() is currently called from scan work, so does not need to reschedule work to call drv_hw_scan(). Signed-off-by:
-
Stanislaw Gruszka authored
This is partial revert and fix for commit 85f72bc8 "mac80211: only cancel software-based scans on suspend" When cfg80211 request the scan and mac80211 perform some management work, we defer the scan request. We do not canceling such requests when calling ieee80211_scan_cancel(), because of SCAN_SW_SCANNING bit check just before the call. So fix that problem. Another problem, which commit 85f72bc8 tries to solve, is we can not cancel HW scan. Hence patch make ieee80211_scan_cancel() ignore HW scan (see code comments). Keeping local->mtx lock assures that the deferred scan will not become "working" HW scan. Signed-off-by:
-
Stanislaw Gruszka authored
We are taking local->mtx inside __ieee80211_scan_completed(), but just before call to that function we drop the lock. Dropping/taking lock is not good, because can lead to hard to understand race conditions. Patch split scan_completed() code into two functions, first must be called with local->mtx taken and second without it. Signed-off-by:
-
Stanislaw Gruszka authored
Use goto instruction to call __ieee80211_scan_completed only ones in ieee80211_scan_work. This is prepare for the next patch. Signed-off-by:
-
Rafał Miłecki authored
It's already set in PHY common code. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Johannes Berg authored
Yikes! The error return keeps a netdev reference and the rdev mutex locked, fix that! Signed-off-by:
-
Johannes Berg authored
This adds API to allow adding per-station GTKs, updates mac80211 to support it, and also allows drivers to remove a key from hwaccel again when this may be necessary due to multiple GTKs. Signed-off-by:
-
Johannes Berg authored
When roaming while we have active BA session, we can end up transmitting delBA frames to the old AP while we're already on the new AP's channel, which can cause warnings. Simply avoid sending those frames, but still tear down the internal session state, since they are not really necessary anyway as we will implicitly disassociate when sending the association to the new AP. Signed-off-by:
Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by:
-
Senthil Balasubramanian authored
Signed-off-by:
Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by:
-
Senthil Balasubramanian authored
drv_config callback is called only after the ack for the nullframe is received and so driver need not do anything special for this. So remove NULLFUNC_COMPLETED, PS_ENABLED flags and bf_isnullfunc flags from ath9k as mac80211 already handles them properly. Signed-off-by:
-
Felix Fietkau authored
After the last rounds of cleanup, these functions are now functionally equivalent and can thus be merged. Also get rid of some excessive (and redundant) debug messages. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
The code gets more concise and readable when making the new ANI functions fall back to the old ones if ANI v2 is disabled. This also makes further code cleanup easier. Signed-off-by:
-
Felix Fietkau authored
Split out the PHY error counter update from ath9k_hw_ani_monitor_*, reuse it in ath9k_hw_proc_mib_event (merged from ath9k_hw_proc_mib_event_old and ath9k_hw_proc_mib_event_new). Signed-off-by:
-
Felix Fietkau authored
ANI state is kept per channel, so instead of keeping an array of ANI states with an arbitrary size of 255, move the ANI state into the channel struct. Move some config settings that are not per-channel out of the per-channel struct to save some memory. With those changes, ath9k_ani_restart_old and ath9k_ani_restart_new can be merged into a single function. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that makes keeping those ops separate rather pointless, as it only increases code size and line number counts. Signed-off-by:
-
Felix Fietkau authored
The cycle counters are used by ANI to determine the amount of time that the radio spent not receiving or transmitting. They're also used for debugging purposes if the baseband watchdog on AR9003 detects a lockup. In the future, we want to use these counters to determine the medium utilization and export this information via survey. For that, we need to make sure that the counter is only accessed from one place, which also ensures that wraparounds won't occur at inconvenient points in time. Signed-off-by:
-
Felix Fietkau authored
The calibration actual calibration flags are only used by the per chip family source files, so it makes more sense to define them in those files instead of globally. That way the code has to test for less flags. Also instead of using a separate callback for testing whether a particular calibration type is supported, simply adjust ah->supp_cals in the calibration init which is called right after the hardware reset, before any of the calibrations are run. Signed-off-by:
-
