- 24 May, 2013 29 commits
-
-
Stanislaw Gruszka authored
Create helper function and move initialization to subroutines. Signed-off-by:
Stanislaw Gruszka <stf_xl@wp.pl> Acked-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
New routine for SOC specific BBP initialization, empty for now. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
This function can not fail, we always return 0. Signed-off-by:
-
- 22 May, 2013 11 commits
-
-
Libo Chen authored
set the owner of platform_driver, to ensure that the caller of driver holds a module refernece Signed-off-by:
Libo Chen <libo.chen@huawei.com> Signed-off-by:
-
Yogesh Ashok Powar authored
Some of the key differences between SD8897 and older chipsets are as follows: a) sdio mpa_rx and mpa_tx ports have been increased from 16 to 32 b) Same is the case with read/write bitmap that one receives from mpa_reg read c) aggregation packet count doubled from 8 to 16 d) Most of key reg addresses are changed e) There is a separate command or control port f) Now command rx/tx_done have new interrupts 1. 'supports_sdio_new_mode' flag is added to handle (a) and (b). 2. (c) and (d) are taken care of by filling chip specific information in global structurei (mwifiex_sdio_sd8897). 3. For older chipsets, port 0 was cmd port and port 1->15 were data port. Therefore we had CTRL_PORT_MASK to differentiate port type. Now these changes are under 'has_control_mask' flag. Signed-off-by:
Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Nishant Sarmukadam <nishants@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
Frank Huang <frankh@marvell.com> Signed-off-by:
-
Amitkumar Karwar authored
There are some macros defined for multiport aggregation calculations. As we may need to add some more code to accomodate new chipsets, we will change them to inline functions. Also, use dynamic allocation for Rx buffer array. Signed-off-by:
-
Amitkumar Karwar authored
They are not used in the code. Signed-off-by:
-
Amitkumar Karwar authored
As Multiple-Port Aggregation base address value is fixed, we can have a macro for it. Signed-off-by:
-
Amitkumar Karwar authored
This patch rearranges the code for better readability Signed-off-by:
-
Amitkumar Karwar authored
Get rid of 'if else' usage by returning in 'if' block. This improves readability by removing indentations. Signed-off-by:
-
Amitkumar Karwar authored
Some u32 variables in sdio.c are used to store/pass u8 values. Replace them with u8 variables. Signed-off-by:
-
Amitkumar Karwar authored
Register addresses, firmware name and some macros are specific to a chip. They are stored in a new structure. Signed-off-by:
-
Amitkumar Karwar authored
Currently supported SDIO chipsets (SD87XX) have 16 ports. This change is a prerequisite for new chipset. Signed-off-by:
-
Amitkumar Karwar authored
User can provide a text file containing calibration data in hex format while loading mwifiex module. It will be downloaded to firmware. eg. insmod mwifiex.ko cal_data_cfg=cal_data.conf Signed-off-by:
-
