vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The hih6130->write_length setting was accidently removed by commit
ebc6b9383f3e "hwmon: (hih6130) Convert to devm_hwmon_device_register_with_groups",
fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip. Avoid auto-conversion from long to int to fix
the problem.

Voltage limits, fan minimum speed, pwm frequency, pwm ramp rate, and
other attributes have the same problem, fix them as well.

Zone temperature limits are signed, but were cached as u8, causing
unepected values to be reported for negative temperatures. Cache as
s8 to fix the problem.

vrm is an u8, so the written value needs to be limited to [0, 255].
Signed-off-by: Axel Lin <axel.lin@ingics.com>
[Guenter Roeck: Fix zone temperature cache]
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Temperature limit range is [-127, 127], not [-127, 128].
The wrong range caused a bad limit to be written into the chip
if the limit was set to a value of 128 degrees C or above.

Also use DIV_ROUND_CLOSEST instead of a plain divide operation
to reduce the rounding error when writing temperature limits.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>

Current code uses data_rate as array index in ads1015_read_adc() and uses pga
as array index in ads1015_reg_to_mv, so we must make sure both data_rate and
pga settings are in valid value range.
Return -EINVAL if the setting is out-of-range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

On platforms with sizeof(int) < sizeof(long), writing a temperature
limit larger than MAXINT will result in unpredictable limit values
written to the chip. Avoid auto-conversion from long to int to fix
the problem.

The hysteresis temperature range depends on the value of
data->temp[attr->index], since val is subtracted from it.
Use a wider clamp, [-120000, 220000] should do to cover the
possible range. Also add missing TEMP_TO_REG() on writes into
cached hysteresis value.

Also uses clamp_val to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
[Guenter Roeck: Fixed double TEMP_TO_REG on hysteresis updates]
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull media updates from Mauro Carvalho Chehab:
 - removal of sn9c102.  This device driver was replaced a long time ago
   by gspca
 - solo6x10 and go7007 webcam drivers moved from staging into
   mainstream.  They were waiting for an API to allow setting the image
   detection matrix
 - SDR drivers moved from staging into mainstream: sdr-msi3101 (renamed
   as msi2500) and rtl2832
 - added SDR driver for airspy
 - added demux driver: si2165
 - rework at several RC subsystem, making the code for RC-5 SZ variant
   to be added at the standard RC5 decoder
 - added decoder for the XMP IR protocol
 - tuner driver moved from staging into mainstream: msi3101 (renamed as
   msi001)
 - added documentation for some additional SDR pixfmt
 - some device tree bindings documented
 - added support for exynos3250 at s5p-jpeg
 - remove the obsolete, unmaintained and broken mx1_camera driver
 - added support for remote controllers at au0828 driver
 - added a RC driver: sunxi-cir
 - several driver fixes, enhancements and cleanups.

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (455 commits)
  [media] cx23885: fix UNSET/TUNER_ABSENT confusion
  [media] coda: fix build error by making reset control optional
  [media] radio-miropcm20: fix sparse NULL pointer warning
  [media] MAINTAINERS: Update go7007 pattern
  [media] MAINTAINERS: Update solo6x10 patterns
  [media] media: atmel-isi: add primary DT support
  [media] media: atmel-isi: convert the pdata from pointer to structure
  [media] media: atmel-isi: add v4l2 async probe support
  [media] rcar_vin: add devicetree support
  [media] media: pxa_camera device-tree support
  [media] media: mt9m111: add device-tree suppport
  [media] soc_camera: add support for dt binding soc_camera drivers
  [media] media: soc_camera: pxa_camera documentation device-tree support
  [media] media: mt9m111: add device-tree documentation
  [media] s5p-mfc: remove unnecessary calling to function video_devdata()
  [media] s5p-jpeg: add chroma subsampling adjustment for Exynos3250
  [media] s5p-jpeg: Prevent erroneous downscaling for Exynos3250 SoC
  [media] s5p-jpeg: Assure proper crop rectangle initialization
  [media] s5p-jpeg: fix g_selection op
  [media] s5p-jpeg: Adjust jpeg_bound_align_image to Exynos3250 needs
  ...

Pull regulator updates from Mark Brown:
 "A couple of nice new features this month, the ability to map
  regulators in order to allow voltage control by external coprocessors
  is something people have been asking for for a long time.

   - improved support for switch only "regulators", allowing current
     state to be read from the parent regulator but no setting.

   - support for obtaining the register access method used to set
     voltages, for use in systems which can offload control of this to a
     coprocessor (typically for DVFS).

   - support for Active-Semi AC8846, Dialog DA9211 and Texas Instruments
     TPS65917"

* tag 'regulator-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (58 commits)
  regulator: act8865: fix build when OF is not enabled
  regulator: act8865: add act8846 to DT binding documentation
  regulator: act8865: add support for act8846
  regulator: act8865: prepare support for other act88xx devices
  regulator: act8865: set correct number of regulators in pdata
  regulator: act8865: Remove error variable in act8865_pmic_probe
  regulator: act8865: fix parsing of platform data
  regulator: tps65090: Set voltage for fixed regulators
  regulator: core: Allow to get voltage count and list from parent
  regulator: core: Get voltage from parent if not available
  regulator: Add missing statics and inlines for stub functions
  regulator: lp872x: Don't set constraints within the regulator driver
  regmap: Fix return code for stub regmap_get_device()
  regulator: s2mps11: Update module description and Kconfig to add S2MPU02 support
  regulator: Add helpers for low-level register access
  regmap: Allow regmap_get_device() to be used by modules
  regmap: Add regmap_get_device
  regulator: da9211: Remove unnecessary devm_regulator_unregister() calls
  regulator: Add DT bindings for tps65218 PMIC regulators.
  regulator: da9211: new regulator driver
  ...

Pull spi updates from Mark Brown:
 "A quiet release, more bug fixes than anything else.  A few things do
  stand out though:

   - updates to several drivers to move towards the standard GPIO chip
     select handling in the core.
   - DMA support for the SH MSIOF driver.
   - support for Rockchip SPI controllers (their first mainline
     submission)"

* tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
  spi: davinci: use spi_device.cs_gpio to store gpio cs per spi device
  spi: davinci: add support to configure gpio cs through dt
  spi/pl022: Explicitly truncate large bitmask
  spi/atmel: Fix pointer to int conversion warnings on 64 bit builds
  spi: davinci: fix to support more than 2 chip selects
  spi: topcliff-pch: don't hardcode PCI slot to get DMA device
  spi: orion: fix incorrect handling of cell-index DT property
  spi: orion: Fix error return code in orion_spi_probe()
  spi/rockchip: fix error return code in rockchip_spi_probe()
  spi/rockchip: remove redundant dev_err call in rockchip_spi_probe()
  spi/rockchip: remove duplicated include from spi-rockchip.c
  ARM: dts: fix the chip select gpios definition in the SPI nodes
  spi: s3c64xx: Update binding documentation
  spi: s3c64xx: use the generic SPI "cs-gpios" property
  spi: s3c64xx: Revert "spi: s3c64xx: Added provision for dedicated cs pin"
  spi: atmel: Use dmaengine_prep_slave_sg() API
  spi: topcliff-pch: Update error messages for dmaengine_prep_slave_sg() API
  spi: sh-msiof: Use correct device for DMA mapping with IOMMU
  spi: sh-msiof: Handle dmaengine_prep_slave_single() failures gracefully
  spi: rspi: Handle dmaengine_prep_slave_sg() failures gracefully
  ...

Pull iommu updates from Joerg Roedel:
 "This time with:

   - support for the generic PCI device alias code in x86 IOMMU drivers

   - a new sysfs interface for IOMMUs

   - preparations for hotplug support in the Intel IOMMU driver

   - change the AMD IOMMUv2 driver to not hold references to core data
     structures like mm_struct or task_struct.  Rely on mmu_notifers
     instead.

   - removal of the OMAP IOVMM interface, all users of it are converted
     to DMA-API now

   - make the struct iommu_ops const everywhere

   - initial PCI support for the ARM SMMU driver

   - there is now a generic device tree binding documented for ARM
     IOMMUs

   - various fixes and cleanups all over the place

  Also included are some changes to the OMAP code, which are acked by
  the maintainer"

* tag 'iommu-updates-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (67 commits)
  devicetree: Add generic IOMMU device tree bindings
  iommu/vt-d: Fix race setting IRQ CPU affinity while freeing IRQ
  iommu/amd: Fix 2 typos in comments
  iommu/amd: Fix device_state reference counting
  iommu/amd: Remove change_pte mmu_notifier call-back
  iommu/amd: Don't set pasid_state->mm to NULL in unbind_pasid
  iommu/exynos: Select ARM_DMA_USE_IOMMU
  iommu/vt-d: Exclude devices using RMRRs from IOMMU API domains
  iommu/omap: Remove platform data da_start and da_end fields
  ARM: omap: Don't set iommu pdata da_start and da_end fields
  iommu/omap: Remove virtual memory manager
  iommu/vt-d: Fix issue in computing domain's iommu_snooping flag
  iommu/vt-d: Introduce helper function iova_size() to improve code readability
  iommu/vt-d: Introduce helper domain_pfn_within_range() to simplify code
  iommu/vt-d: Simplify intel_unmap_sg() and kill duplicated code
  iommu/vt-d: Change iommu_enable/disable_translation to return void
  iommu/vt-d: Simplify include/linux/dmar.h
  iommu/vt-d: Avoid freeing virtual machine domain in free_dmar_iommu()
  iommu/vt-d: Fix possible invalid memory access caused by free_dmar_iommu()
  iommu/vt-d: Allocate dynamic domain id for virtual domains only
  ...

Pull hwmon updates from Guenter Roeck:
 "Notable changes:

   - Heiko Schocher provided a driver for TI TMP103.
   - Kamil Debski provided a driver for pwm-controlled fans.
   - Neelesh Gupta provided a driver for power, fan rpm, voltage and
     temperature reporting on powerpc/powernv systems.
   - Scott Kanowitz provided a driver supporting Lattice's POWR1220
     power manager IC.
   - Richard Zhu provided a pmbus front-end driver for TPS40422.
   - Frans Klaver added support for TMP112 to the lm75 driver.
   - Johannes Pointner added support for EPCOS B57330V2103 to the
     ntc_thermistor driver.
   - Guenter Roeck added support for TMP441 and TMP442 to the tmp421
     driver.
   - Axel Lin converted several drivers to the new hwmon API (36 of
     them, if I counted correctly), and cleaned up many of the drivers
     along the way.

  There are also a number of patches fixing bugs discovered while
  testing Axel's changes"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (88 commits)
  hwmon: (g762) Use of_property_read_u32 at appropriate place
  hwmon: (sis5595) Prevent overflow problem when writing large limits
  hwmon: (gpio-fan) Prevent overflow problem when writing large limits
  hwmon: (ibmpowernv) Use of_property_read_u32 at appropriate place
  hwmon: (lm85) Convert to devm_hwmon_device_register_with_groups
  hwmon: (lm85) Avoid forward declaration
  hwmon: (lm78) Convert to devm_hwmon_device_register_with_groups
  hwmon: (max6697) Use of_property_read_bool at appropriate places
  hwmon: (pwm-fan) Make SENSORS_PWM_FAN depend on OF
  hwmon: (pwm-fan) Remove duplicate dev_set_drvdata call
  hwmon: (nct6775) Remove num_attr_groups from struct nct6775_data
  hwmon: (nct6775) Update module description and Kconfig for NCT6106D and NCT6791D
  hwmon: (adt7411) Convert to devm_hwmon_device_register_with_groups
  hwmon: (g762) Convert to hwmon_device_register_with_groups
  hwmon: (emc2103) Convert to devm_hwmon_device_register_with_groups
  hwmon: (smsc47m1) Avoid forward declaration
  hwmon: (smsc47m192) Convert to devm_hwmon_device_register_with_groups
  hwmon: (smsc47m192) Avoid forward declaration
  hwmon: (max1668) Make max1668_addr_list array const
  hwmon: (max6639) Make normal_i2c array const
  ...

Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regulator-next

Merge remote-tracking branches 'regulator/topic/tps65217', 'regulator/topic/tps65218', 'regulator/topic/tps6586x' and 'regulator/topic/twl' into regulator-next

Merge remote-tracking branches 'regulator/topic/s2mps11', 'regulator/topic/s2mpu02', 'regulator/topic/s5m8767' and 'regulator/topic/tps65090' into regulator-next

Merge remote-tracking branches 'regulator/topic/lp8755', 'regulator/topic/ltc3589', 'regulator/topic/max8952', 'regulator/topic/mc13xxx' and 'regulator/topic/palmas' into regulator-next

Merge remote-tracking branches 'regulator/topic/da9211', 'regulator/topic/getreg', 'regulator/topic/gpio' and 'regulator/topic/lp872x' into regulator-next

Merge remote-tracking branches 'regulator/topic/88pm800', 'regulator/topic/ab8500', 'regulator/topic/act8865', 'regulator/topic/as3722' and 'regulator/topic/bcm590xx' into regulator-next

Merge remote-tracking branches 'regulator/fix/act8865', 'regulator/fix/arizona' and 'regulator/fix/tps65218' into regulator-linus

Conflicts:
	drivers/regulator/act8865-regulator.c

Pull ARM updates from Russell King:
 "Included in this update:

   - perf updates from Will Deacon:

     The main changes are callchain stability fixes from Jean Pihet and
     event mapping and PMU name rework from Mark Rutland

     The latter is preparatory work for enabling some code re-use with
     arm64 in the future.

   - updates for nommu from Uwe Kleine-König:

     Two different fixes for the same problem making some ARM nommu
     configurations not boot since 3.6-rc1.  The problem is that
     user_addr_max returned the biggest available RAM address which
     makes some copy_from_user variants fail to read from XIP memory.

   - deprecate legacy OMAP DMA API, in preparation for it's removal.

     The popular drivers have been converted over, leaving a very small
     number of rarely used drivers, which hopefully can be converted
     during the next cycle with a bit more visibility (and hopefully
     people popping out of the woodwork to help test)

   - more tweaks for BE systems, particularly with the kernel image
     format.  In connection with this, I've cleaned up the way we
     generate the linker script for the decompressor.

   - removal of hard-coded assumptions of the kernel stack size, making
     everywhere depend on the value of THREAD_SIZE_ORDER.

   - MCPM updates from Nicolas Pitre.

   - Make it easier for proper CPU part number checks (which should
     always include the vendor field).

   - Assembly code optimisation - use the "bx" instruction when
     returning from a function on ARMv6+ rather than "mov pc, reg".

   - Save the last kernel misaligned fault location and report it via
     the procfs alignment file.

   - Clean up the way we create the initial stack frame, which is a
     repeated pattern in several different locations.

   - Support for 8-byte get_user(), needed for some DRM implementations.

   - mcs locking from Will Deacon.

   - Save and restore a few more Cortex-A9 registers (for errata
     workarounds)

   - Fix various aspects of the SWP emulation, and the ELF hwcap for the
     SWP instruction.

   - Update LPAE logic for pte_write and pmd_write to make it more
     correct.

   - Support for Broadcom Brahma15 CPU cores.

   - ARM assembly crypto updates from Ard Biesheuvel"

* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (53 commits)
  ARM: add comments to the early page table remap code
  ARM: 8122/1: smp_scu: enable SCU standby support
  ARM: 8121/1: smp_scu: use macro for SCU enable bit
  ARM: 8120/1: crypto: sha512: add ARM NEON implementation
  ARM: 8119/1: crypto: sha1: add ARM NEON implementation
  ARM: 8118/1: crypto: sha1/make use of common SHA-1 structures
  ARM: 8113/1: remove remaining definitions of PLAT_PHYS_OFFSET from <mach/memory.h>
  ARM: 8111/1: Enable erratum 798181 for Broadcom Brahma-B15
  ARM: 8110/1: do CPU-specific init for Broadcom Brahma15 cores
  ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE
  ARM: 8108/1: mm: Introduce {pte,pmd}_isset and {pte,pmd}_isclear
  ARM: hwcap: disable HWCAP_SWP if the CPU advertises it has exclusives
  ARM: SWP emulation: only initialise on ARMv7 CPUs
  ARM: SWP emulation: always enable when SMP is enabled
  ARM: 8103/1: save/restore Cortex-A9 CP15 registers on suspend/resume
  ARM: 8098/1: mcs lock: implement wfe-based polling for MCS locking
  ARM: 8091/2: add get_user() support for 8 byte types
  ARM: 8097/1: unistd.h: relocate comments back to place
  ARM: 8096/1: Describe required sort order for textofs-y (TEXT_OFFSET)
  ARM: 8090/1: add revision info for PL310 errata 588369 and 727915
  ...

act8846_matches and act8865_matches are defined only when OF is
enabled. Move references to them to the act8865_pdata_from_dt()
function to avoid a build error when OF is disabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

This patch adds a new "active-semi,act8846" compatible string and a
list of supported regulator names to the devicetree binding
documentation for Active-Semi PMUs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Add device id and definition of registers and regulators to support
the act8846 PMU.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

This patch prepares support for other devices in the act88xx family of
PMUs manufactured by Active-Semi.

http://www.active-semi.com/products/power-management-units/act88xx/Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

act8865_pdata_from_dt() populates the array pdata->regulators with all
the regulators and then assigns the field init_data only for the ones
actually found in the DT.

The patch changes the value assigned to pdata->num_regulators to match
the size of the array.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Simply use ret variable instead.
Also remove unneeded initialize for ret variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

The driver loops through all available regulators (ACT8865_REG_NUM)
and accesses pdata->regulators[i].platform_data without checking the
actual value of num_regulators in platform data, potentially causing a
invalid memory access.

Fix this and look up the regulator init_data by id in platform data.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by Wenyou.Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Pull m68knommu fixes from Greg Ungerer:
 "Just a couple of small fixes.  Fix definition of page_to_phys() and
  remove unecesary prototype of kobjsize()"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: Remove unnecessary prototype for kobjsize()
  m68knommu: Correct page_to_phys when PAGE_OFFSET is non-zero.

Conflicts:
	arch/arm/kernel/perf_event_cpu.c

Conflicts:
	arch/arm/kernel/iwmmxt.S
	arch/arm/mm/cache-l2x0.c
	arch/arm/mm/mmu.c

Pull ext4 updates from Ted Ts'o:
 "Bug fixes and clean ups for the 3.17 merge window"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix ext4_discard_allocated_blocks() if we can't allocate the pa struct
  ext4: fix COLLAPSE RANGE test for bigalloc file systems
  ext4: check inline directory before converting
  ext4: fix incorrect locking in move_extent_per_page
  ext4: use correct depth value
  ext4: add i_data_sem sanity check
  ext4: fix wrong size computation in ext4_mb_normalize_request()
  ext4: make ext4_has_inline_data() as a inline function
  ext4: remove readpage() check in ext4_mmap_file()
  ext4: fix punch hole on files with indirect mapping
  ext4: remove metadata reservation checks
  ext4: rearrange initialization to fix EXT4FS_DEBUG

Pull f2fs updates from Jaegeuk Kim:
 "This series includes patches to:
   - add nobarrier mount option
   - support tmpfile and rename2
   - enhance the fdatasync behavior
   - fix the error path
   - fix the recovery routine
   - refactor a part of the checkpoint procedure
   - reduce some lock contentions"

* tag 'for-f2fs-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (40 commits)
  f2fs: use for_each_set_bit to simplify the code
  f2fs: add f2fs_balance_fs for expand_inode_data
  f2fs: invalidate xattr node page when evict inode
  f2fs: avoid skipping recover_inline_xattr after recover_inline_data
  f2fs: add tracepoint for f2fs_direct_IO
  f2fs: reduce competition among node page writes
  f2fs: fix coding style
  f2fs: remove redundant lines in allocate_data_block
  f2fs: add tracepoint for f2fs_issue_flush
  f2fs: avoid retrying wrong recovery routine when error was occurred
  f2fs: test before set/clear bits
  f2fs: fix wrong condition for unlikely
  f2fs: enable in-place-update for fdatasync
  f2fs: skip unnecessary data writes during fsync
  f2fs: add info of appended or updated data writes
  f2fs: use radix_tree for ino management
  f2fs: add infra for ino management
  f2fs: punch the core function for inode management
  f2fs: add nobarrier mount option
  f2fs: fix to put root inode in error path of fill_super
  ...

Pull USB updates from Greg KH:
 "Here is the big USB driver update for 3.17-rc1.

  Loads of gadget driver changes in here, including some big file
  movements to make things easier to manage over time.  There's also the
  usual xhci and uas driver updates, and a handful of other changes in
  here.  The changelog has the full details.

  All of these have been in linux-next for a while"

* tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits)
  USB: devio: fix issue with log flooding
  uas: Log a warning when we cannot use uas because the hcd lacks streams
  uas: Only complain about missing sg if all other checks succeed
  xhci: Add missing checks for xhci_alloc_command failure
  xhci: Rename Asrock P67 pci product-id to EJ168
  xhci: Blacklist using streams on the Etron EJ168 controller
  uas: Limit qdepth to 32 when connected over usb-2
  uwb/whci: use correct structure type name in sizeof
  usb-core bInterval quirk
  USB: serial: ftdi_sio: Add support for new Xsens devices
  USB: serial: ftdi_sio: Annotate the current Xsens PID assignments
  usb: chipidea: debug: fix sparse non static symbol warnings
  usb: ci_hdrc_imx doc: fsl,usbphy is required
  usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY
  usb: core: allow zero packet flag for interrupt urbs
  usb: lvstest: Fix sparse warnings generated by kbuild test bot
  USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down
  phy: miphy365x: Represent each PHY channel as a DT subnode
  phy: miphy365x: Provide support for the MiPHY356x Generic PHY
  phy: miphy365x: Add Device Tree bindings for the MiPHY365x
  ...

Pull tty / serial driver update from Greg KH:
 "Here's the big tty / serial driver update for 3.17-rc1.

  Nothing major, just a number of fixes and new features for different
  serial drivers, and some more tty core fixes and documentation of the
  tty locks.

  All of these have been in linux-next for a while"

* tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (82 commits)
  tty/n_gsm.c: fix a memory leak in gsmld_open
  pch_uart: don't hardcode PCI slot to get DMA device
  tty: n_gsm, use setup_timer
  Revert "ARC: [arcfpga] stdout-path now suffices for earlycon/console"
  serial: sc16is7xx: Correct initialization of s->clk
  serial: 8250_dw: Add support for deferred probing
  serial: 8250_dw: Add optional reset control support
  serial: st-asc: Fix overflow in baudrate calculation
  serial: st-asc: Don't call BUG in asc_console_setup()
  tty: serial: msm: Make of_device_id array const
  tty/n_gsm.c: get gsm->num after gsm_activate_mux
  serial/core: Fix too big allocation for attribute member
  drivers/tty/serial: use correct type for dma_map/unmap
  serial: altera_jtaguart: Fix putchar function passed to uart_console_write()
  serial/uart/8250: Add tunable RX interrupt trigger I/F of FIFO buffers
  Serial: allow port drivers to have a default attribute group
  tty: kgdb_nmi: Automatically manage tty enable
  serial: altera_jtaguart: Adpot uart_console_write()
  serial: samsung: improve code clarity by defining a variable
  serial: samsung: correct the case and default order in switch
  ...