Eric Dumazet spotted that we have to check skb->head instead
of skb->data as skb->head points to the beginning of the
data area of the skbuff. Similarly, we have to initialize the
skb->head pointer, not skb->data in __alloc_skb_head.

After this fix, netlink crashes in the release path of the
sk_buff, so let's fix that as well.

This bug was introduced in (0ebd0ac5 net: add function to
allocate sk_buff head without data area).
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 091f0ea3 "tg3: Add New 5719 Read
DMA workaround" added a workaround for TX DMA stall on the 5719. This
workaround needs to be applied to the 5720 as well.

Cc: stable@vger.kernel.org
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets the protocol selector bits (4:0) of the PHY's MII_ADVERTISE
register (ANAR) when writing ADVERTISE_ALL. The protocol selector bits are
indicating IEEE 803.3u support and are fixed / read-only on some PHYs. Not
setting them correctly on others (like TI DP83630) makes the PHY fall back
to 10M HDX mode which should be avoided.

Tested for TI DP83630 PHY on Microblaze platform.
Signed-off-by: Jens Renner <renner@efe-gmbh.de>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was recently found out that GSO on 57710/57711 was broken, due to packets
being sent without a valid IP checksum.

Commit 057cf65e "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this
issue, but failed to set the correct IP checksum when receiving GSO packets
via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed
to calculate IP checksum were erroneously set in the incorrect
buffer descriptor.

This patch re-enables GSO in said scenario for 57710/57711 chips.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW was initialized with data from wrong header, this caused TSO packets
have wrong IP csum.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 25fb6ca4
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
forgot to assign rt6_info to the inet6_ifaddr.
When disable the net device, the rt6_info which allocated
in init_loopback will not be destroied in __ipv6_ifa_notify.

This will trigger the waring message below
[23527.916091] unregister_netdevice: waiting for tap0 to become free. Usage count = 1
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
here are there fixes for the v3.10 release cycle:

The first patch by Jonas Peterson and Olivier Sobrie fixes the reception of CAN
frames on Kvaser's "USBcan Pro" and "USBcan R" type hardware.

The last two patches by Olivier Sobrie (for esd_usb2) and me (for peak_usb)
change the memory handling for the USB messages from stack to kmalloc(), as
memory used for DMA should not be allocated on stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

MAC addresses assigned by the PF to VFs were not kept in the PF driver
admin table. As a result, displaying the VF MACs from the PF interface
to user space showed zero address where in fact the VF got non-zero
address from the PF, fix that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a VF sense they didn't get MAC address, use random one. This will
address the case of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the PF initialization, SRIOV is enabled before the PF is fully initialized.
This allows the kernel to probe the newly-exposed VFs before the PF is ready
to handle them (nested probes).

Have the probe method return the -EPROBE_DEFER value in this situation (instead
of the VF probe method retrying its initialization in a loop, and returning -EIO
on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel
itself will retry the probe after a suitable delay.

Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When turning on adaptive_rx under adaptive moderation, the CQ's moderation
count wasn't updated according to rx_frames which resulted in too many
interrupts and bandwidth drop.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

smatch reports the following warnings:
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:514 pcan_usb_pro_drv_loaded() error: doing dma on the stack (buffer)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:878 pcan_usb_pro_init() error: doing dma on the stack (&fi)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:889 pcan_usb_pro_init() error: doing dma on the stack (&bi)

See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"

Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

smatch reports the following warnings:
drivers/net/can/usb/esd_usb2.c:640 esd_usb2_start() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:846 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:855 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:923 esd_usb2_set_bittiming() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1047 esd_usb2_probe() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1053 esd_usb2_probe() error: doing dma on the stack (&msg)

See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Unlike Kvaser Leaf light devices, some other Kvaser devices (like USBcan
Pro, USBcan R) receive CAN messages in CMD_LOG_MESSAGE frames. This
patch adds support for it.

Cc: linux-stable <stable@vger.kernel.org> # >= v3.8
Signed-off-by: Jonas Peterson <jonas.peterson@gmail.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

commit 56b765b7 ("htb: improved accuracy at high rates")
broke the "overhead xxx" handling, as well as the "linklayer atm"
attribute.

tc class add ... htb rate X ceil Y linklayer atm overhead 10

This patch restores the "overhead xxx" handling, for htb, tbf
and act_police

The "linklayer atm" thing needs a separate fix.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vimalkumar <j.vimal@gmail.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roman Gushchin discovered that udp4_lib_lookup2() was not reloading
first item in the rcu protected list, in case the loop was restarted.

This produced soft lockups as in https://lkml.org/lkml/2013/4/16/37

rcu_dereference(X)/ACCESS_ONCE(X) seem to not work as intended if X is
ptr->field :

In some cases, gcc caches the value or ptr->field in a register.

Use a barrier() to disallow such caching, as documented in
Documentation/atomic_ops.txt line 114

Thanks a lot to Roman for providing analysis and numerous patches.
Diagnosed-by: Roman Gushchin <klamm@yandex-team.ru>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Boris Zhmurov <zhmurov@yandex-team.ru>
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the recent addition of 8021AD, we need to set the new field vlan_proto in
sk_buff. Otherwise, it will trigger BUG() call in vlan_proto_idx().

This patch fixes the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case the port list dump does not fit into one skb currently the
dump would start over again. Fix this by continue from the last dumped
port.

Introduced by commit d90f889e (team: handle sending port list in the
same way option list is sent)
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

non-rcu variant of list_first_or_null_rcu
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SELinux labeled IPsec code was improperly handling its reference
counting, dropping a reference on a delete operation instead of on a
free/release operation.
Reported-by: Ondrej Moris <omoris@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases after deleting a policy from the SPD the policy would
remain in the dst/flow/route cache for an extended period of time
which caused problems for SELinux as its dynamic network access
controls key off of the number of XFRM policy and state entries.
This patch corrects this problem by forcing a XFRM garbage collection
whenever a policy is sucessfully removed.
Reported-by: Ondrej Moris <omoris@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp6 over GRE tunnel does not work after to GRE tso changes. GRE
tso handler passes inner packet but keeps track of outer header
start in SKB_GSO_CB(skb)->mac_offset.  udp6 fragment need to
take care of outer header, which start at the mac_offset, while
adding fragment header.
This bug is introduced by commit 68c33163 (GRE: Add TCP
segmentation offload for GRE).
Reported-by: Dmitry Kravkov <dkravkov@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Tested-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dev_mc_sync_multiple function is currently calling
__hw_addr_sync, and not __hw_addr_sync_multiple.  This will result in
addresses only being synced to the first device from the set.

	Corrected by calling the _multiple variant.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, __hw_addr_sync_one is called in a loop by
__hw_addr_sync_multiple to sync each of a "from" device's hw addresses
to a "to" device.  __hw_addr_sync_one calls __hw_addr_add_ex to attempt
to add each address.  __hw_addr_add_ex is called with global=false, and
sync=true.

	__hw_addr_add_ex checks to see if the new address matches an
address already on the list.  If so, it tests global and sync.  In this
case, sync=true, and it then checks if the address is already synced,
and if so, returns 0.

	This 0 return causes __hw_addr_sync_one to increment the sync_cnt
and refcount for the "from" list's address entry, even though the address
is already synced and has a reference and sync_cnt.  This will cause
the sync_cnt and refcount to increment without bound every time an
addresses is added to the "from" device and synced to the "to" device.

	The fix here has two parts:

	First, when __hw_addr_add_ex finds the address already exists
and is synced, return -EEXIST instead of 0.

	Second, __hw_addr_sync_one checks the error return for -EEXIST,
and if so, it (a) does not add a refcount/sync_cnt, and (b) returns 0
itself so that __hw_addr_sync_multiple will not return an error.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an address is added to a subordinate interface (the "to"
list), the address entry in the "from" list is not marked "synced" as
the entry added to the "to" list is.

	When performing the unsync operation (e.g., dev_mc_unsync),
__hw_addr_unsync_one calls __hw_addr_del_entry with the "synced"
parameter set to true for the case when the address reference is being
released from the "from" list.  This causes a test inside to fail,
with the result being that the reference count on the "from" address
is not properly decremeted and the address on the "from" list will
never be freed.

	Correct this by having __hw_addr_unsync_one call the
__hw_addr_del_entry function with the "sync" flag set to false for the
"remove from the from list" case.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sync_cnt field is not being initialized, which can result
in arbitrary values in the field.  Fixed by initializing it to zero.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This stat is not relevant in IPv6, there is no checksum in IPv6 header.
Just leave a comment to explain the hole.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
Please pull this batch of fixes intended for the 3.10 stream...

Regarding the NFC bits, Samuel says:

"This is the first batch of NFC fixes for 3.10, and it contains:

- 3 fixes for the NFC MEI support:
        * We now depend on the correct Kconfig symbol.
        * We register an MEI event callback whenever we enable an NFC device,
          otherwise we fail to read anything after an enable/disable cycle.
        * We only disable an MEI device from its disable mey_phy_ops,
          preventing useless consecutive disable calls.

- An NFC Makefile cleanup, as I forgot to remove a commented out line when
  moving the LLCP code to the NFC top level directory."

As for the mac80211 bits, Johannes says:

"This time I have a fix from Stanislaw for a stupid mistake I made in the
auth/assoc timeout changes, a fix from Felix for 64-bit traffic counters
and one from Helmut for address mask handling in mac80211. I also have a
few fixes myself for four different crashes reported by a few people."

And Johannes says this about the iwlwifi bit:

"This fixes a brown paper-bag bug that we really should've caught in
review. More details in the changelog for the fix."

On top of that...

Arend van Spriel and Hante Meuleman cooperate to send a series of AP
and P2P mode fixes for brcmfmac.

Gabor Juhos corrects a register offset for AR9550, avoiding a bus
error.

Dan Carpenter provides a fixup to some dmesg output in the atmel
driver.

And, finally...

Felix Fietkau not only gives us a trio of small AR934x fixes, but
also refactors the ath9k aggregation session start/stop handling
(using the generic mac80211 support) in order to avoid a deadlock.

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

During a PCI EEH/AER error recovery flow, if the device did not successfully
restart, the error_detected() hook may be called a second time with a
"perm_failure" state. This patch skips over driver cleanup for the second
invocation of the callback.

Also, Lancer error recovery code is fixed-up to handle these changes.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter/IPVS fixes for 3.10-rc3,
they are:

* fix xt_addrtype with IPv6, from Florian Westphal. This required
  a new hook for IPv6 functions in the netfilter core to avoid
  hard dependencies with the ipv6 subsystem when this match is
  only used for IPv4.

* fix connection reuse case in IPVS. Currently, if an reused
  connection are directed to the same server. If that server is
  down, those connection would fail. Therefore, clear the
  connection and choose a new server among the available ones.

* fix possible non-nul terminated string sent to user-space if
  ipt_ULOG is used as the default netfilter logging stub, from
  Chen Gang.

* fix mark logging of IPv6 packets in xt_LOG, from Michal Kubecek.
  This bug has been there since 2.6.26.

* Fix breakage ip_vs_sh due to incorrect structure layout for
  RCU, from Jan Beulich.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

kfree_rcu() requires offsetof(..., rcu_head) < 4096, which can
get violated with a sufficiently high CONFIG_IP_VS_SH_TAB_BITS.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

In dump_ipv6_packet(), the "recurse" parameter is zero only if
dumping contents of a packet embedded into an ICMPv6 error
message. Therefore we want to log packet mark if recurse is
non-zero, not when it is zero.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

We currently allow changing the mq flag (IFF_MULTI_QUEUE) for a persistent
device. This will result a mismatch between the number the queues in netdev and
tuntap. This is because we only allocate a 1q netdevice when IFF_MULTI_QUEUE was
not specified, so when we set the IFF_MULTI_QUEUE and try to attach more queues
later, netif_set_real_num_tx_queues() may fail which result a single queue
netdevice with multiple sockets attached.

Solve this by disallowing changing the mq flag for persistent device.

Bug was introduced by commit edfb6a14
(tuntap: reduce memory using of queues).
Reported-by: Sriram Narasimhan <sriram.narasimhan@hp.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The three arrays of strings: af_family_key_strings,
af_family_slock_key_strings and af_family_clock_key_strings have not
VSOCK's string
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To: linux-kernel@vger.kernel.org
Cc: x86@kernel.org, trinity@vger.kernel.org, Andy Lutomirski <luto@amacapital.net>, netdev@vger.kernel.org, "David S.
	Miller" <davem@davemloft.net>
Subject: [PATCH 5/5] net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg

MSG_CMSG_COMPAT is (AFAIK) not intended to be part of the API --
it's a hack that steals a bit to indicate to other networking code
that a compat entry was used.  So don't allow it from a non-compat
syscall.

This prevents an oops when running this code:

int main()
{
	int s;
	struct sockaddr_in addr;
	struct msghdr *hdr;

	char *highpage = mmap((void*)(TASK_SIZE_MAX - 4096), 4096,
	                      PROT_READ | PROT_WRITE,
	                      MAP_PRIVATE | MAP_ANONYMOUS | MAP_FIXED, -1, 0);
	if (highpage == MAP_FAILED)
		err(1, "mmap");

	s = socket(AF_INET, SOCK_DGRAM, IPPROTO_UDP);
	if (s == -1)
		err(1, "socket");

        addr.sin_family = AF_INET;
        addr.sin_port = htons(1);
        addr.sin_addr.s_addr = htonl(INADDR_LOOPBACK);
	if (connect(s, (struct sockaddr*)&addr, sizeof(addr)) != 0)
		err(1, "connect");

	void *evil = highpage + 4096 - COMPAT_MSGHDR_SIZE;
	printf("Evil address is %p\n", evil);

	if (syscall(__NR_sendmmsg, s, evil, 1, MSG_CMSG_COMPAT) < 0)
		err(1, "sendmmsg");

	return 0;
}

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accessing the OTP memory on AR9950 causes a data bus
like this:

  Data bus error, epc == 801f7774, ra == 801f7774
  Oops[#1]:
  CPU: 0 PID: 1 Comm: swapper Not tainted 3.10.0-rc3 #592
  task: 87c28000 ti: 87c22000 task.ti: 87c22000
  $ 0   : 00000000 00000061 deadc0de 00000000
  $ 4   : b8115f18 00015f18 00000007 00000004
  $ 8   : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
  $12   : 7c7c3c7c 80320a68 00000000 7c7c7c3c
  $16   : 87cd8010 00015f18 00000007 00000000
  $20   : 00000064 00000004 87c23c7c 8035210c
  $24   : 00000000 801f3674
  $28   : 87c22000 87c23b48 00000001 801f7774
  Hi    : 00000000
  Lo    : 00000064
  epc   : 801f7774 ath9k_hw_wait+0x58/0xb0
      Not tainted
  ra    : 801f7774 ath9k_hw_wait+0x58/0xb0
  Status: 1000cc03 KERNEL EXL IE
  Cause : 4080801c
  PrId  : 00019750 (MIPS 74Kc)
  Modules linked in:
  Process swapper (pid: 1, threadinfo=87c22000, task=87c28000, ts=00000000)
  Stack : 0000000f 00000061 00002710 8006240c 00000001 87cd8010 87c23bb0 87cd8010
          00000000 00000004 00000003 80210c7c 000000b3 67fa8000 0000032a 000006fe
          000003e8 00000002 00000028 87c23bf0 000003ff 80210d24 803e5630 80210e28
          00000000 00000007 87cd8010 00007044 00000004 00000061 000003ff 000001ff
          87c26000 87cd8010 00000220 87cd8bb8 80210000 8020fcf4 87c22000 87c23c08
          ...
  Call Trace:
  [<801f7774>] ath9k_hw_wait+0x58/0xb0
  [<80210c7c>] ar9300_otp_read_word+0x80/0xd4
  [<80210d24>] ar9300_read_otp+0x54/0xb0
  [<8020fcf4>] ar9300_check_eeprom_header+0x1c/0x40
  [<80210fe4>] ath9k_hw_ar9300_fill_eeprom+0x118/0x39c
  [<80206650>] ath9k_hw_eeprom_init+0x74/0xb4
  [<801f96d0>] ath9k_hw_init+0x7ec/0x96c
  [<801e65ec>] ath9k_init_device+0x340/0x758
  [<801f35d0>] ath_ahb_probe+0x21c/0x2c0
  [<801c041c>] driver_probe_device+0xc0/0x1e4
  [<801c05ac>] __driver_attach+0x6c/0xa4
  [<801bea08>] bus_for_each_dev+0x64/0xa8
  [<801bfa40>] bus_add_driver+0xcc/0x24c
  [<801c0954>] driver_register+0xbc/0x17c
  [<803f8fc0>] ath9k_init+0x5c/0x88
  [<800608fc>] do_one_initcall+0xec/0x1a0
  [<803e6a68>] kernel_init_freeable+0x13c/0x200
  [<80309cdc>] kernel_init+0x1c/0xe4
  [<80062450>] ret_from_kernel_thread+0x10/0x18

On the AR9550, the OTP registers are located at
the same address as on the AR9340. Use the correct
values to avoid the error.

Cc: stable@vger.kernel.org  # 3.6+
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For p2p client mode powersave mode should be kept disabled. It is
working but inefficient. In general p2p links do no benefit from this
mode, because these links are setup temporarily to transfer data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>