- 01 Apr, 2022 32 commits
-
-
Kent Russell authored
Since unique_id is only supported in PMFW 0x3A5300 and higher, we will only be able to use it inside Smu_Metrics_V3_t, which requires PMFW 0x3A4900 and higher. Remove the unique_id/serial_number references from the v1 and v2 tables to avoid any confusion, and return 0 if metrics_v1 or metrics_v2 are used to try to get the unique_id/serial_number. Signed-off-by:
Kent Russell <kent.russell@amd.com> Reviewed-by:
Lijo Lazar <lijo.lazar@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Melissa Wen authored
FPU documentation states that developers must not use DC_FP_START/END inside dml files, but use this macro to wrap calls to FPU functions in dc folder (outside dml folder). Therefore, this patch removes DC_FP_* wrappers from dml folder and wraps calls for these FPU operations outside dml, as required. Acked-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by:
Melissa Wen <mwen@igalia.com> Signed-off-by:
-
Melissa Wen authored
dcn10_validate_bandwidth is only used on dcn10 files, but is declared in dcn_calcs files. Rename dcn10_* to dcn_* in calcs, remove DC_FP_* wrapper inside DML folder and create an specific dcn10_validate_bandwidth in dcn10_resources that calls dcn_validate_bandwidth and properly wraps that FPU function with DC_FP_* macro. Acked-by:
-
Kent Russell authored
This is being added to SMU Metrics, so add the required tie-ins in the kernel. Also create the corresponding unique_id sysfs file. v2: Add FW version check, remove SMU mutex v3: Fix style warning v4: Add MP1 IP_VERSION check to FW version check Signed-off-by:
-
Kent Russell authored
This is abstracted well enough in the get_metrics_data function, so use the function Signed-off-by:
-
Kent Russell authored
This will allow us to use the generic *_get_metrics_data functions for ASICs that support unique_id Signed-off-by:
-
Kent Russell authored
To ease readability, use switch to set unique_id as supported for the supported IP_VERSIONs, and set it to unsupported by default for all other ASICs. This makes it easier to add IP_VERSIONs later on, and makes it obvious that it is not supported by default, instead of the current logic that assumes that it is supported unless it is not one of the specified IP_VERSIONs. v2: Rebase onto previous IP_VERSION change Signed-off-by:
Kevin Wang <KevinYang.Wang@amd.com> Signed-off-by:
-
Philip Yang authored
To support multi-thread update page table. Signed-off-by:
Philip Yang <Philip.Yang@amd.com> Reviewed-by:
-
Christian König authored
That are bytes not pages. Signed-off-by:
-
Christian König authored
Fix two incorrect kerneldocs for the recent VM code changes. v2: fix one more typo Signed-off-by:
kernel test robot <lkp@intel.com> Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by:
-
Shirish S authored
[Why] comparing pwm bl values (coverted) with user brightness(converted) levels in commit_tail leads to continuous setting of backlight via dmub as they don't to match. This leads overdrive in queuing of commands to DMCU that sometimes lead to depending on load on DMCU fw: "[drm:dc_dmub_srv_wait_idle] *ERROR* Error waiting for DMUB idle: status=3" [How] Store last successfully set backlight value and compare with it instead of pwm reads which is not what we should compare with. Signed-off-by:
Shirish S <shirish.s@amd.com> Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
-
Randy Dunlap authored
There is no need for this one static function to be marked as kernel-doc notation. Avoid this doc build warning: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst * Enable CRTC Fixes: 110d3968 ("drm/amd/display: Add DCN3.1 OPTC") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Cc: amd-gfx@lists.freedesktop.org Cc: Christian König <christian.koenig@amd.com> Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com> Cc: Harry Wentland <harry.wentland@amd.com> Cc: Leo Li <sunpeng.li@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by:
-
Haowen Bai authored
The value actual_pix_clk_100Hz is dereferencing pointer pix_clk_params before pix_clk_params is being null checked. Fix this by assigning pix_clk_params->requested_pix_clk_100hz to actual_pix_clk_100Hz only if pix_clk_params is not NULL, otherwise just NULL. Signed-off-by:
Haowen Bai <baihaowen@meizu.com> Signed-off-by:
-
Philip Yang authored
Flush TLB needs wait for GPU update fence done. MMU notify callback to unmap range from GPUs uses unlocked GPU page table update, so add tlb_cb to unlocked update fence to increase vm->tlb_seq. Signed-off-by:
-
Philip Yang authored
To fix two issues with unlocked update fence: 1. vm->last_unlocked store the latest fence without taking refcount. 2. amdgpu_vm_bo_update_mapping returns old fence, not the latest fence. Signed-off-by:
-
Haowen Bai authored
The pointer edid_buf is dereferencing pointer edid before edid is being null checked. Fix this by assigning edid->raw_edid to edid_buf only if edid is not NULL, otherwise just NULL. Signed-off-by:
-
Roman Li authored
[Why] On resume we do link detection for all non-MST connectors. MST is handled separately. However the condition for telling if connector is on mst branch is not enough for mst hub case. Link detection for mst branch link leads to mst topology reset. That causes assert in dc_link_allocate_mst_payload() [How] Use link type as indicator for mst link. Reviewed-by:
Wayne Lin <Wayne.Lin@amd.com> Acked-by:
Alex Hung <alex.hung@amd.com> Signed-off-by:
Roman Li <Roman.Li@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
-
Aric Cyr authored
- [FW Promotion] Release 0.0.110.0 - Revert FEC check in validation - Update LTTPR UHBR link rate support struct - Add support for USBC connector - Add work around for AUX failure on wake - Clear optc false state when disable otg - Enable power gating before init_pipes - Remove redundant dsc power gating from init_hw - Power down hardware if timer not trigger - Correct Slice reset calculation - Enable 3-plane MPO for DCN31 - Set fec register init value - Remove SW w/a for HDCP 1.4 1A-07 failure based on ECO fix - Create underflow interrupt IRQ type Acked-by:
Aric Cyr <aric.cyr@amd.com> Tested-by:
-
Anthony Koo authored
- Revert save/restore PANEL_PWRSEQ_REF_DIV2 and other psr phy optimizations Reviewed-by:
Anthony Koo <Anthony.Koo@amd.com> Tested-by:
-
Martin Leung authored
why and how: causes failure on install on certain machines Reviewed-by:
George Shen <George.Shen@amd.com> Acked-by:
Martin Leung <Martin.Leung@amd.com> Tested-by:
-
Michael Strauss authored
[WHY] Update field order to match DP2.0 spec SCR Reviewed-by:
Michael Strauss <michael.strauss@amd.com> Tested-by:
-
Samson Tam authored
[Why] Add support for CONNECTOR_ID_USBC Reviewed-by:
Alvin Lee <Alvin.Lee2@amd.com> Acked-by:
Samson Tam <Samson.Tam@amd.com> Tested-by:
-
Jimmy Kizito authored
[Why] When waking from low-power states, a DP sink may remain unresponsive to AUX transactions. [How] Try to toggle DPCD SET_POWER register repeatedly (up to a maximum timeout value) until DP sink becomes responsive. Reviewed-by:
Mustapha Ghaddar <Mustapha.Ghaddar@amd.com> Acked-by:
Jimmy Kizito <Jimmy.Kizito@amd.com> Tested-by:
-
Charlene Liu authored
[why] when disable optc, need to clear the underflow status as well. Reviewed-by:
Chris Park <Chris.Park@amd.com> Acked-by:
Charlene Liu <Charlene.Liu@amd.com> Tested-by:
-
Roman Li authored
[Why] In init_hw() we call init_pipes() before enabling power gating. init_pipes() tries to power gate dsc but it may fail because required force-ons are not released yet. As a result with dsc config the following errors observed on resume: "REG_WAIT timeout 1us * 1000 tries - dcn20_dsc_pg_control" "REG_WAIT timeout 1us * 1000 tries - dcn20_dpp_pg_control" "REG_WAIT timeout 1us * 1000 tries - dcn20_hubp_pg_control" [How] Move enable_power_gating_plane() before init_pipes() in init_hw() Reviewed-by:
Eric Yang <Eric.Yang2@amd.com> Acked-by:
-
Roman Li authored
[Why] DSC Power down code has been moved from dcn31_init_hw into init_pipes() Need to remove it from dcn10_init_hw() as well to avoid duplicated action on dcn1.x/2.x [How] Remove DSC power down code from dcn10_init_hw() Fixes: 8fa6f4c5 ("drm/amd/display: fixed the DSC power off sequence during Driver PnP") Reviewed-by:
-
Paul Hsieh authored
[WHY] In headless systems, if SetMode/Power down timer is not called, hardware will not be powered down causing HW/SW discrepancies. Powering down hardware on SetPowerState to D3 will ensure SW/HW state is accurate. [HOW] If PowerDownThread timer is not trigger but OS call SetPowerState to D3, power down hardware. Reviewed-by:
Paul Hsieh <paul.hsieh@amd.com> Tested-by:
-
Chris Park authored
[Why] Once DSC slice cannot fit pixel clock, we incorrectly reset min slices to 0 and allow max slice to operate, even when max slice itself cannot fit the pixel clock properly. [How] Change the sequence such that we correctly determine DSC is not possible when both min slices and max slices cannot fit pixel clock per slice. Reviewed-by:
Wenjing Liu <Wenjing.Liu@amd.com> Acked-by:
-
Krunoslav Kovac authored
[WHY&HOW] It can be enabled by users, but proper way is to report max_slave_planes in DC caps for each ASIC. Some structures use hardcoded max_plane=2, this is also addressed here. Reviewed-by:
Nevenko Stupar <Nevenko.Stupar@amd.com> Reviewed-by:
Krunoslav Kovac <Krunoslav.Kovac@amd.com> Tested-by:
-
Jingwen Zhu authored
[Why] We don't include this eDP FEC init on fastboot. [How] Set the fec to init value when stopping driver &get the fec register value to check should enable FEC. Co-authored-by:
Jingwen Zhu <Jingwen.Zhu@amd.com> Reviewed-by:
-
Oliver Logush authored
[why] W/a no longer needed Reviewed-by:
Oliver Logush <oliver.logush@amd.com> Tested-by:
-
Angus Wang authored
[WHY] We want another entry in IRQ type that can be used to help find the underflow interrupt source. [HOW] Added another mapping in IRQ type enum. Reviewed-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
Angus Wang <Angus.Wang@amd.com> Tested-by:
-
- 28 Mar, 2022 8 commits
-
-
Mohammad Zafar Ziya authored
RAS error query support addition for JPEG 2.6 V2: removed unused options and corrected comment format. Moved register definition to header file. V3: poison query status check added. Removed the error query support V4: Return statement refactored. Signed-off-by:
Mohammad Zafar Ziya <Mohammadzafar.ziya@amd.com> Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by:
Tao Zhou <tao.zhou1@amd.com> Signed-off-by:
-
Mohammad Zafar Ziya authored
RAS error query support addition for VCN 2.6 V2: removed unused option and corrected comment format Moved the register definition under header file V3: poison query status check added. Removed error query interface V4: MMSCH poison check option removed, return true/false refactored. Signed-off-by:
-
Mohammad Zafar Ziya authored
Adding vcn and jpeg ver 2.6 ras register definition Signed-off-by:
-
Mohammad Zafar Ziya authored
Ras support addition for JPEG block V2: removed default callback Signed-off-by:
-
Mohammad Zafar Ziya authored
VCN block ras feature support addition V2: default ras callback removed Signed-off-by:
-
Mohammad Zafar Ziya authored
Add vcn and jpeg ras support options V2: vcn and jpeg ras flag enabled for aldebaran asic only V3: vcn and jpeg ras flag disabled for error counter query Generic poison query interface added VCN and JPEG ras enabled based on IP version check V4: vcn and jpeg ras flag moved under ecc flag for dGPU Signed-off-by:
-
tiancyin authored
Some video card has more than one vcn instance, passing 0 to vcn_v3_0_pause_dpg_mode is incorrect. Error msg: Register(1) [mmUVD_POWER_STATUS] failed to reach value 0x00000001 != 0x00000002 Reviewed-by:
James Zhu <James.Zhu@amd.com> Signed-off-by:
tiancyin <tianci.yin@amd.com> Signed-off-by:
-
Sean Paul authored
ATOMIC and DRIVER log categories do not typically contain per-frame log messages. This patch re-classifies some messages in amd to chattier categories to keep ATOMIC/DRIVER quiet. Acked-by:
Sean Paul <seanpaul@chromium.org> Signed-off-by:
-
