- 23 Jul, 2020 40 commits
-
-
Paul Greenwalt authored
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new values and report PHY autoneg capability. Signed-off-by:
Paul Greenwalt <paul.greenwalt@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Paul Greenwalt authored
Add debug logs for ice_aq_get_phy_caps(), and format ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them more readable. Signed-off-by:
Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by:
-
Bruce Allan authored
When the Port Disable bit is set in the Link Default Override Mask TLV PFA module in the NVM, Total Port Shutdown mode is supported and enabled. In this mode, the driver should act as if the link-down-on-close ethtool private flag is always enabled and dis-allow any change to that flag. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Signed-off-by:
-
Paul Greenwalt authored
Adds functions to check for link override firmware support and get the override settings for a port. The previously supported/default link mode was strict mode. In strict mode link is configured based on get PHY capabilities PHY types with media. Lenient mode is now the default link mode. In lenient mode the link is configured based on get PHY capabilities PHY types without media. This allows the user to configure link that the media does not report. Limit the minimum supported link mode to 25G for devices that support 100G, and 1G for devices that support less than 100G. Default override is only supported in lenient mode. If default override is supported and enabled, then default override values are used for configuring speed and FEC. Default override provide persistent link settings in the NVM. Signed-off-by:
Evan Swanson <evan.swanson@intel.com> Tested-by:
-
Paul Greenwalt authored
After the transition from no media to media FW will clear the set-phy-cfg data set by the user. Save initial PHY settings and any settings later requested by the user and use that data to restore PHY settings on media insertion. Since PHY configuration is now being stored, replace calls that were calling FW to get the configuration with the saved copy. Signed-off-by:
Chinh T Cao <chinh.t.cao@intel.com> Signed-off-by:
-
Paul Greenwalt authored
The call to ice_cfg_phy_fec() requires the caller to perform certain actions before calling it. Instead of imposing these preconditions move the operations into the function and perform them ourselves. Also, fix some style issues in nearby touched code. Signed-off-by:
-
Paul Greenwalt authored
Create a helper function for configuring requested flow control so that it can be utilized by other functions looking to configure flow control settings. Utilize the existing helper ice_copy_phy_caps_to_cfg() to copy a PHY capability to configuration instead duplicating the code for it. Signed-off-by:
-
Akeem G Abodunrin authored
Add callbacks needed to support advanced power management for Wake on LAN. Also make ice_pf_state_is_nominal function available for all configurations not just CONFIG_PCI_IOV. Signed-off-by:
Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
-
Jacob Keller authored
Using the new ice_aq_list_caps and ice_parse_(dev|func)_caps functions, replace ice_discover_caps with two functions that each take a pointer to the dev_caps and func_caps structures respectively. This makes the side effect of updating the hw->dev_caps and hw->func_caps obvious from reading the implementation of the function. Additionally, it opens the way for enabling reading of device capabilities outside of the initialization flow. By passing in a pointer, another caller will be able to read the capabilities without modifying the HW capabilities structures. As there are no other callers, it is safe to now remove ice_aq_discover_caps and ice_parse_caps. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
Jacob Keller authored
The ice_parse_caps function is used to convert the capability block data coming from firmware into a structured format used by other parts of the code. The current implementation directly updates the hw->func_caps and hw->dev_caps structures. It is directly called from within ice_aq_discover_caps. This causes the discover_caps function to have the side effect of modifying the HW capability structures, which is not intuitive. Split this function into ice_parse_dev_caps and ice_parse_func_caps. These functions will take a pointer to the dev_caps and func_caps respectively. Also create an ice_parse_common_caps for sharing the capability logic that is common to device and function. Doing so enables a future refactor to allow reading and parsing capabilities into a local caps structure instead of modifying the members of the HW structure directly. Signed-off-by:
-
Jacob Keller authored
The ice_discover_caps function is used to read the device and function capabilities, updating the hardware capabilities structures with relevant data. The exact number of capabilities returned by the hardware is unknown ahead of time. The AdminQ command will report the total number of capabilities in the return buffer. The current implementation involves requesting capabilities once, reading this returned size, and then re-requested with that size. This isn't really necessary. The firmware interface has a maximum size of ICE_AQ_MAX_BUF_LEN. Firmware can never return more than ICE_AQ_MAX_BUF_LEN / sizeof(struct ice_aqc_list_caps_elem) capabilities. Avoid the retry loop by simply allocating a buffer of size ICE_AQ_MAX_BUF_LEN. This is significantly simpler than retrying. The extra allocation isn't a big deal, as it will be released after we finish parsing the capabilities. Signed-off-by:
-
David S. Miller authored
Tom Parkin says: ==================== l2tp: further checkpatch.pl cleanups l2tp hasn't been kept up to date with the static analysis checks offered by checkpatch.pl. This patchset builds on the series "l2tp: cleanup checkpatch.pl warnings". It includes small refactoring changes which improve code quality and resolve a subset of the checkpatch warnings for the l2tp codebase. ==================== Reviewed-by:
James Chapman <jchapman@katalix.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Tom Parkin authored
Passing "sizeof(struct blah)" in kzalloc calls is less readable, potentially prone to future bugs if the type of the pointer is changed, and triggers checkpatch warnings. Tweak the kzalloc calls in l2tp which use this form to avoid the warning. Signed-off-by:
Tom Parkin <tparkin@katalix.com> Signed-off-by:
-
Tom Parkin authored
When creating an L2TP tunnel using the netlink API, userspace must either pass a socket FD for the tunnel to use (for managed tunnels), or specify the tunnel source/destination address (for unmanaged tunnels). Since source/destination addresses may be AF_INET or AF_INET6, the l2tp netlink code has conditionally compiled blocks to support IPv6. Rather than embedding these directly into l2tp_nl_cmd_tunnel_create (where it makes the code difficult to read and confuses checkpatch to boot) split the handling of address-related attributes into a separate function. Signed-off-by:
-
Tom Parkin authored
l2tp_nl_tunnel_send has conditionally compiled code to support AF_INET6, which makes the code difficult to follow and triggers checkpatch warnings. Split the code out into functions to handle the AF_INET v.s. AF_INET6 cases, which both improves readability and resolves the checkpatch warnings. Signed-off-by:
-
Tom Parkin authored
checkpatch warns about indentation and brace balancing around the conditionally compiled code for AF_INET6 support in l2tp_dfs_seq_tunnel_show. By adding another check on the socket address type we can make the code more readable while removing the checkpatch warning. Signed-off-by:
-
Tom Parkin authored
These checks are all simple and don't benefit from extra braces to clarify intent. Remove them for easier-reading code. Signed-off-by:
-
Tom Parkin authored
checkpatch warns about comparisons to NULL, e.g. CHECK: Comparison to NULL could be written "!rt" #474: FILE: net/l2tp/l2tp_ip.c:474: + if (rt == NULL) { These sort of comparisons are generally clearer and more readable the way checkpatch suggests, so update l2tp accordingly. Signed-off-by: -
Miaohe Lin authored
Use eth_zero_addr() to clear mac address insetad of memset(). Signed-off-by:
Miaohe Lin <linmiaohe@huawei.com> Signed-off-by:
-
Miaohe Lin authored
Use eth_zero_addr() to clear mac address insetad of memset(). Signed-off-by:
-
David S. Miller authored
Paolo Abeni says: ==================== mptcp: non backup subflows pre-reqs This series contains a bunch of MPTCP improvements loosely related to concurrent subflows xmit usage, currently under development. The first 3 patches are actually bugfixes for issues that will become apparent as soon as we will enable the above feature. The later patches improve the handling of incoming additional subflows, improving significantly the performances in stress tests based on a high new connection rate. ==================== Signed-off-by: -
Paolo Abeni authored
So that we can easily perform some basic PM-related adimission checks before creating the child socket. Reviewed-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Tested-by:
Christoph Paasch <cpaasch@apple.com> Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Paolo Abeni authored
tcp_send_active_reset() is more prone to transient errors (memory allocation or xmit queue full): in stress conditions the kernel may drop the egress packet, and the client will be stuck. Reviewed-by:
-
Paolo Abeni authored
When syncookie are in use, the TCP stack may feed into subflow_syn_recv_sock() plain TCP request sockets. We can't access mptcp_subflow_request_sock-specific fields on such sockets. Explicitly check the rsk ops to do safe accesses. Reviewed-by:
-
Paolo Abeni authored
The mentioned function has several unneeded branches, handle each case - MP_CAPABLE, MP_JOIN, fallback - under a single conditional and drop quite a bit of duplicate code. Reviewed-by:
-
Paolo Abeni authored
Currently accepted msk sockets become established only after accept() returns the new sk to user-space. As MP_JOIN request are refused as per RFC spec on non fully established socket, the above causes mp_join self-tests instabilities. This change lets the msk entering the established status as soon as it receives the 3rd ack and propagates the first subflow fully established status on the msk socket. Finally we can change the subflow acceptance condition to take in account both the sock state and the msk fully established flag. Reviewed-by:
-
Paolo Abeni authored
In the unlikely event of a failure at connect time, we currently clear the request_mptcp flag - so that the MPC handshake is not started at all, but the msk is not explicitly marked as fallback. This would lead to later insertion of wrong DSS options in the xmitted packets, in violation of RFC specs and possibly fooling the peer. Fixes: e1ff9e82 ("net: mptcp: improve fallback to TCP") Reviewed-by:
-
Paolo Abeni authored
When updating a partially acked data fragment, we actually corrupt it. This is irrelevant till we send data on a single subflow, as retransmitted data, if any are discarded by the peer as duplicate, but it will cause data corruption as soon as we will start creating non backup subflows. Reviewed-by:
-
Paolo Abeni authored
Currently we do not init the subflow write sequence for MP_JOIN subflows. This will cause bad mapping being generated as soon as we will use non backup subflow. Reviewed-by:
-
Jakub Kicinski authored
Check MC_CMD_DRV_ATTACH_EXT_OUT_FLAG_TRUSTED, before setting the info, which will hopefully protect us from -EPERM errors the previous code was gracefully ignoring. Ed reports this is not the 100% correct bit, but it's the best approximation we have. Shared code reports the port information back to user space, so we really want to know what was added and what failed. Ignoring -EPERM is not an option. The driver does not call udp_tunnel_get_rx_info(), so its own management of table state is not really all that problematic, we can leave it be. This allows the driver to continue with its copious table syncing, and matching the ports to TX frames, which it will reportedly do one day. Leave the feature checking in the callbacks, as the device may remove the capabilities on reset. Inline the loop from __efx_ef10_udp_tnl_lookup_port() into efx_ef10_udp_tnl_has_port(), since it's the only caller now. With new infra this driver gains port replace - when space frees up in a full table a new port will be selected for offload. Plus efx will no longer sleep in an atomic context. v2: - amend the commit message about TRUSTED not being 100% - add TUNNEL_ENCAP_UDP_PORT_ENTRY_INVALID to mark unsed entries Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Acked-By:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
David S. Miller authored
Alexander Lobakin says: ==================== qed, qede: improve chain API and add XDP_REDIRECT support This series adds missing XDP_REDIRECT case handling in QLogic Everest Ethernet driver with all necessary prerequisites and ops. QEDE Tx relies heavily on chain API, so make sure it is in its best at first. v2 (from [1]): - add missing includes to #003 to pass the build on Alpha; - no functional changes. [1] https://lore.kernel.org/netdev/20200722155349.747-1-alobakin@marvell.com/ ==================== Signed-off-by:
-
Alexander Lobakin authored
Add XDP_REDIRECT case handling and the corresponding NDO to support redirecting XDP frames. This also includes registering driver memory model (currently order-0 page mode) in BPF subsystem. The total number of XDP queues is usually 1:1 with Rx ones. Signed-off-by:
Alexander Lobakin <alobakin@marvell.com> Signed-off-by:
Igor Russkikh <irusskikh@marvell.com> Signed-off-by:
Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by:
-
Alexander Lobakin authored
Current XDP Tx logic is suboptimal and can't be reused for XDP_REDIRECT path. Make qede_xdp_{tx_int,xmit}() more universal and effective in general to allow future expanding. Misc: use unlikely() hints where appropriate and replace "fallthrough" comments with pseudo-keywords. Signed-off-by: -
Alexander Lobakin authored
Correct the indentation of net_device_ops declarations for fancier look. Signed-off-by:
-
Alexander Lobakin authored
Make the file more readable and easier for adding new fields. Misc: use IFNAMSIZ and netdev_name() instead of sizeof_field() and direct net_device::name dereferencing. Signed-off-by:
-
Alexander Lobakin authored
Add reverse-variants of qed_chain_get_elem_left{,u32}() to be able to know current chain occupation. They will be used in the upcoming qede XDP_REDIRECT code. They share most of the logics with the mentioned ones, so were reused to collapse the latters. Signed-off-by: -
Alexander Lobakin authored
Constify chain pointers and refactor qed_chain_get_elem_left{,u32}() a bit. Signed-off-by: -
Alexander Lobakin authored
Extend current infrastructure to store chain page size in a struct and use it in all functions instead of fixed QED_CHAIN_PAGE_SIZE. Its value remains the default one, but can be overridden in qed_chain_init_params before chain allocation. Signed-off-by:
-
Alexander Lobakin authored
To simplify qed_chain_alloc() prototype and call sites, introduce struct qed_chain_init_params to specify chain params, and pass a pointer to filled struct to the actual qed_chain_alloc() instead of a long list of separate arguments. Signed-off-by:
-
Alexander Lobakin authored
Fill PBL table parameters for chains with an external PBL data earlier on qed_chain_init_params() rather than on allocation itself. This simplifies allocation code and allows to extend struct ext_pbl for other chain types. Signed-off-by:
-
