Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.

Drop the special defines in a bunch of drivers where the
removal is relatively simple so grouping into one patch
does not impact reviewability.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6xxx driver expects switches that are configured in single chip
addressing mode to have the MDIO address configured as 0. This is due to
the switch ADDR pins representing the single chip addressing mode as 0.
However depending on the device (e.g. MV88E6*41) the switch does not
respond on address 0 or any other address below 16 (the first port
address) in single chip addressing mode. This allows for other devices
to be on the same shared MDIO bus despite the switch being in single
chip addressing mode.

When using a switch that works this way it is not possible to configure
switch driver as single chip addressing via device tree, along with
another MDIO device on the same bus with address 0, as both devices
would have the same address of 0 resulting in mdiobus_register_device
-EBUSY errors for one of the devices with address 0.

In order to support this configuration the switch node can have its MDIO
address configured as 16 (the first address that the device responds
to). During initialization the driver will treat this address similar to
how address 0 is, however because this address is also a valid
multi-chip address (in certain switch models, but not all) the driver
will configure the SMI in single chip addressing mode and attempt to
detect the switch model. If the device is configured in single chip
addressing mode this will succeed and the initialization process can
continue. If it fails to detect a valid model this is because the switch
model register is not a valid register when in multi-chip mode, it will
then fall back to the existing SMI initialization process using the MDIO
address as the multi-chip mode address.

This detection method is safe if the device is in either mode because
the single chip addressing mode read is a direct SMI/MDIO read operation
and has no side effects compared to the SMI writes required for the
multi-chip addressing mode.

In order to implement this change, the reset gpio configuration is moved
to occur before any SMI initialization. This ensures that the device has
the same/correct reset gpio state for both mv88e6xxx_smi_init calls.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220427130928.540007-1-nathan@nathanrossi.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

- Add HW api to configure policer:
  - SR TCM policer mode is only supported for now.
  - Policer ingress/egress direction support.
- Add police action support into flower
Signed-off-by: Volodymyr Mytnyk <volodymyr.mytnyk@plvision.eu>
Link: https://lore.kernel.org/r/1651061148-21321-1-git-send-email-volodymyr.mytnyk@plvision.euSigned-off-by: Jakub Kicinski <kuba@kernel.org>

phy_attach_direct() first calls phy_init_hw() (which restores interrupt
settings through ->config_intr()), then calls phy_disable_interrupts().

So if phydev->interrupts was previously set to 1, interrupts are briefly
enabled, then disabled, which seems nonsensical.

If it was previously set to 0, interrupts are disabled twice, which is
equally nonsensical.

Deduplicate interrupt disablement.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/805ccdc606bd8898d59931bd4c7c68537ed6e550.1651040826.git.lukas@wunner.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Adding a new socket option, SO_RCVMARK, to indicate that SO_MARK
should be included in the ancillary data returned by recvmsg().

Renamed the sock_recv_ts_and_drops() function to sock_recv_cmsgs().
Signed-off-by: Erin MacNeil <lnx.erin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220427200259.2564-1-lnx.erin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

include/linux/netdevice.h
net/core/dev.c
  6510ea97 ("net: Use this_cpu_inc() to increment net->core_stats")
  794c24e9 ("net-core: rx_otherhost_dropped to core_stats")
https://lore.kernel.org/all/20220428111903.5f4304e0@canb.auug.org.au/

drivers/net/wan/cosa.c
  d48fea84 ("net: cosa: fix error check return value of register_chrdev()")
  89fbca33 ("net: wan: remove support for COSA and SRP synchronous serial boards")
https://lore.kernel.org/all/20220428112130.1f689e5e@canb.auug.org.au/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bluetooth, bpf and netfilter.

  Current release - new code bugs:

   - bridge: switchdev: check br_vlan_group() return value

   - use this_cpu_inc() to increment net->core_stats, fix preempt-rt

  Previous releases - regressions:

   - eth: stmmac: fix write to sgmii_adapter_base

  Previous releases - always broken:

   - netfilter: nf_conntrack_tcp: re-init for syn packets only,
     resolving issues with TCP fastopen

   - tcp: md5: fix incorrect tcp_header_len for incoming connections

   - tcp: fix F-RTO may not work correctly when receiving DSACK

   - tcp: ensure use of most recently sent skb when filling rate samples

   - tcp: fix potential xmit stalls caused by TCP_NOTSENT_LOWAT

   - virtio_net: fix wrong buf address calculation when using xdp

   - xsk: fix forwarding when combining copy mode with busy poll

   - xsk: fix possible crash when multiple sockets are created

   - bpf: lwt: fix crash when using bpf_skb_set_tunnel_key() from
     bpf_xmit lwt hook

   - sctp: null-check asoc strreset_chunk in sctp_generate_reconf_event

   - wireguard: device: check for metadata_dst with skb_valid_dst()

   - netfilter: update ip6_route_me_harder to consider L3 domain

   - gre: make o_seqno start from 0 in native mode

   - gre: switch o_seqno to atomic to prevent races in collect_md mode

  Misc:

   - add Eric Dumazet to networking maintainers

   - dt: dsa: realtek: remove realtek,rtl8367s string

   - netfilter: flowtable: Remove the empty file"

* tag 'net-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
  tcp: fix F-RTO may not work correctly when receiving DSACK
  Revert "ibmvnic: Add ethtool private flag for driver-defined queue limits"
  net: enetc: allow tc-etf offload even with NETIF_F_CSUM_MASK
  ixgbe: ensure IPsec VF<->PF compatibility
  MAINTAINERS: Update BNXT entry with firmware files
  netfilter: nft_socket: only do sk lookups when indev is available
  net: fec: add missing of_node_put() in fec_enet_init_stop_mode()
  bnx2x: fix napi API usage sequence
  tls: Skip tls_append_frag on zero copy size
  Add Eric Dumazet to networking maintainers
  netfilter: conntrack: fix udp offload timeout sysctl
  netfilter: nf_conntrack_tcp: re-init for syn packets only
  net: dsa: lantiq_gswip: Don't set GSWIP_MII_CFG_RMII_CLK
  net: Use this_cpu_inc() to increment net->core_stats
  Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted
  Bluetooth: hci_event: Fix creating hci_conn object on error status
  Bluetooth: hci_event: Fix checking for invalid handle on error status
  ice: fix use-after-free when deinitializing mailbox snapshot
  ice: wait 5 s for EMP reset after firmware flash
  ice: Protect vf_state check by cfg_lock in ice_vc_process_vf_msg()
  ...

Pull thermal control fixes from Rafael Wysocki:
 "These take back recent chages that started to confuse users and fix up
  an attr.show callback prototype in a driver.

  Specifics:

   - Stop warning about deprecation of the userspace thermal governor
     and cooling device status interface, because there are cases in
     which user space has to drive thermal management with the help of
     them (Daniel Lezcano)

   - Fix attr.show callback prototype in the int340x thermal driver
     (Kees Cook)"

* tag 'thermal-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  thermal/governor: Remove deprecated information
  Revert "thermal/core: Deprecate changing cooling device state from userspace"
  thermal: int340x: Fix attr.show callback prototype

Pull power management fixes from Rafael Wysocki:
 "These fix up recent intel_idle driver changes and fix some ARM cpufreq
  driver issues.

  Specifics:

   - Fix issues with the Qualcomm's cpufreq driver (Dmitry Baryshkov,
     Vladimir Zapolskiy).

   - Fix memory leak with the Sun501 driver (Xiaobing Luo).

   - Make intel_idle enable C1E promotion on all CPUs when C1E is
     preferred to C1 (Artem Bityutskiy).

   - Make C6 optimization on Sapphire Rapids added recently work as
     expected if both C1E and C1 are "preferred" (Artem Bityutskiy)"

* tag 'pm-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  intel_idle: Fix SPR C6 optimization
  intel_idle: Fix the 'preferred_cstates' module parameter
  cpufreq: qcom-cpufreq-hw: Clear dcvs interrupts
  cpufreq: fix memory leak in sun50i_cpufreq_nvmem_probe
  cpufreq: qcom-cpufreq-hw: Fix throttle frequency value on EPSS platforms
  cpufreq: qcom-hw: provide online/offline operations
  cpufreq: qcom-hw: fix the opp entries refcounting
  cpufreq: qcom-hw: fix the race between LMH worker and cpuhp
  cpufreq: qcom-hw: drop affinity hint before freeing the IRQ

Pull ACPI fixes from Rafael WysockiL
 "These fix up the ACPI processor driver after a change made during the
  5.16 cycle that inadvertently broke falling back to shallower C-states
  when C3 cannot be used.

  Specifics:

   - Make the ACPI processor driver avoid falling back to C3 type of
     C-states when C3 cannot be requested (Ville Syrjälä)

   - Revert a quirk that is not necessary any more after fixing the
     underlying issue properly (Ville Syrjälä)"

* tag 'acpi-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPI: processor: idle: fix lockup regression on 32-bit ThinkPad T40"
  ACPI: processor: idle: Avoid falling back to C3 type C-states

Merge tag 'platform-drivers-x86-v5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver fixes from Hans de Goede:
 "Highlights:

   - asus-wmi bug-fixes

   - intel-sdsu bug-fixes

   - build (warning) fixes

   - couple of hw-id additions"

* tag 'platform-drivers-x86-v5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/x86/intel: pmc/core: change pmc_lpm_modes to static
  platform/x86/intel/sdsi: Fix bug in multi packet reads
  platform/x86/intel/sdsi: Poll on ready bit for writes
  platform/x86/intel/sdsi: Handle leaky bucket
  platform/x86: intel-uncore-freq: Prevent driver loading in guests
  platform/x86: gigabyte-wmi: added support for B660 GAMING X DDR4 motherboard
  platform/x86: dell-laptop: Add quirk entry for Latitude 7520
  platform/x86: asus-wmi: Fix driver not binding when fan curve control probe fails
  platform/x86: asus-wmi: Potential buffer overflow in asus_wmi_evaluate_method_buf()
  tools/power/x86/intel-speed-select: fix build failure when using -Wl,--as-needed

Merge tag 'regulator-fix-v5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fix from Mark Brown:
 "A minor fix for the DT binding documentation of the rt5190a driver"

* tag 'regulator-fix-v5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: dt-bindings: Revise the rt5190a buck/ldo description

Currently DSACK is regarded as a dupack, which may cause
F-RTO to incorrectly enter "loss was real" when receiving
DSACK.

Packetdrill to demonstrate:

// Enable F-RTO and TLP
    0 `sysctl -q net.ipv4.tcp_frto=2`
    0 `sysctl -q net.ipv4.tcp_early_retrans=3`
    0 `sysctl -q net.ipv4.tcp_congestion_control=cubic`

// Establish a connection
   +0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

// RTT 10ms, RTO 210ms
  +.1 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
   +0 > S. 0:0(0) ack 1 <...>
 +.01 < . 1:1(0) ack 1 win 257
   +0 accept(3, ..., ...) = 4

// Send 2 data segments
   +0 write(4, ..., 2000) = 2000
   +0 > P. 1:2001(2000) ack 1

// TLP
+.022 > P. 1001:2001(1000) ack 1

// Continue to send 8 data segments
   +0 write(4, ..., 10000) = 10000
   +0 > P. 2001:10001(8000) ack 1

// RTO
+.188 > . 1:1001(1000) ack 1

// The original data is acked and new data is sent(F-RTO step 2.b)
   +0 < . 1:1(0) ack 2001 win 257
   +0 > P. 10001:12001(2000) ack 1

// D-SACK caused by TLP is regarded as a dupack, this results in
// the incorrect judgment of "loss was real"(F-RTO step 3.a)
+.022 < . 1:1(0) ack 2001 win 257 <sack 1001:2001,nop,nop>

// Never-retransmitted data(3001:4001) are acked and
// expect to switch to open state(F-RTO step 3.b)
   +0 < . 1:1(0) ack 4001 win 257
+0 %{ assert tcpi_ca_state == 0, tcpi_ca_state }%

Fixes: e33099f9 ("tcp: implement RFC5682 F-RTO")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1650967419-2150-1-git-send-email-yangpc@wangsu.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

1) Fix incorrect TCP connection tracking window reset for non-syn
   packets, from Florian Westphal.

2) Incorrect dependency on CONFIG_NFT_FLOW_OFFLOAD, from Volodymyr Mytnyk.

3) Fix nft_socket from the output path, from Florian Westphal.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: nft_socket: only do sk lookups when indev is available
  netfilter: conntrack: fix udp offload timeout sysctl
  netfilter: nf_conntrack_tcp: re-init for syn packets only
====================

Link: https://lore.kernel.org/r/20220428142109.38726-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull gfs2 fix from Andreas Gruenbacher:

 - No short reads or writes upon glock contention

* tag 'gfs2-v5.18-rc4-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: No short reads or writes upon glock contention

This reverts commit 723ad916

When client requests channel or ring size larger than what the server
can support the server will cap the request to the supported max. So,
the client would not be able to successfully request resources that
exceed the server limit.

Fixes: 723ad916 ("ibmvnic: Add ethtool private flag for driver-defined queue limits")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220427235146.23189-1-drt@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The Time-Specified Departure feature is indeed mutually exclusive with
TX IP checksumming in ENETC, but TX checksumming in itself is broken and
was removed from this driver in commit 82728b91 ("enetc: Remove Tx
checksumming offload code").

The blamed commit declared NETIF_F_HW_CSUM in dev->features to comply
with software TSO's expectations, and still did the checksumming in
software by calling skb_checksum_help(). So there isn't any restriction
for the Time-Specified Departure feature.

However, enetc_setup_tc_txtime() doesn't understand that, and blindly
looks for NETIF_F_CSUM_MASK.

Instead of checking for things which can literally never happen in the
current code base, just remove the check and let the driver offload
tc-etf qdiscs.

Fixes: acede3c5 ("net: enetc: declare NETIF_F_HW_CSUM and do it in software")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220427203017.1291634-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The VF driver can forward any IPsec flags and such makes the function
is not extendable and prone to backward/forward incompatibility.

If new software runs on VF, it won't know that PF configured something
completely different as it "knows" only XFRM_OFFLOAD_INBOUND flag.

Fixes: eda0333a ("ixgbe: add VF IPsec management")
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shannon Nelson <snelson@pensando.io>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220427173152.443102-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull xfs fixes from Dave Chinner:

 - define buffer bit flags as unsigned to fix gcc-5 + c11 warnings

 - remove redundant XFS fields from MAINTAINERS

 - fix inode buffer locking order regression

* tag 'xfs-5.18-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: reorder iunlink remove operation in xfs_ifree
  MAINTAINERS: update IOMAP FILESYSTEM LIBRARY and XFS FILESYSTEM
  xfs: convert buffer flags to unsigned.

There appears to be a maintainer gap for BNXT TEE firmware files which
causes some patches to be missed. Update the entry for the BNXT Ethernet
controller with its companion firmware files.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220427163606.126154-1-f.fainelli@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge a fix for the attr.show callback prototype in the int340x thermal
driver (Kees Cook).

* thermal-int340x:
  thermal: int340x: Fix attr.show callback prototype

Check if the incoming interface is available and NFT_BREAK
in case neither skb->sk nor input device are set.

Because nf_sk_lookup_slow*() assume packet headers are in the
'in' direction, use in postrouting is not going to yield a meaningful
result.  Same is true for the forward chain, so restrict the use
to prerouting, input and output.

Use in output work if a socket is already attached to the skb.

Fixes: 554ced0a ("netfilter: nf_tables: add support for native socket matching")
Reported-and-tested-by: Topi Miettinen <toiwoton@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Merge cpuidle fixes for 5.18-rc5:

 - Make intel_idle enable C1E promotion on all CPUs when C1E is
   preferred to C1 (Artem Bityutskiy).

 - Make C6 optimization on Sapphire Rapids added recently work as
   expected if both C1E and C1 are "preferred" (Artem Bityutskiy).

* pm-cpuidle:
  intel_idle: Fix SPR C6 optimization
  intel_idle: Fix the 'preferred_cstates' module parameter

Commit 00bfe02f ("gfs2: Fix mmap + page fault deadlocks for buffered
I/O") changed gfs2_file_read_iter() and gfs2_file_buffered_write() to
allow dropping the inode glock while faulting in user buffers.  When the
lock was dropped, a short result was returned to indicate that the
operation was interrupted.

As pointed out by Linus (see the link below), this behavior is broken
and the operations should always re-acquire the inode glock and resume
the operation instead.

Link: https://lore.kernel.org/lkml/CAHk-=whaz-g_nOOoo8RRiWNjnv2R+h6_xk2F1J4TuSRxk1MtLw@mail.gmail.com/
Fixes: 00bfe02f ("gfs2: Fix mmap + page fault deadlocks for buffered I/O")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>

I missed a stray return; in net_rx_action(), which very well
is taken whenever trigger_rx_softirq() has been called on
a cpu that is no longer receiving network packets,
or receiving too few of them.

Fixes: 68822bdf ("net: generalize skb freeing deferral to per-cpu lists")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220427204147.1310161-1-eric.dumazet@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Luiz Augusto von Dentz says:

====================
bluetooth pull request for net:

 - Fix regression causing some HCI events to be discarded when they
   shouldn't.

* tag 'for-net-2022-04-27' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
  Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted
  Bluetooth: hci_event: Fix creating hci_conn object on error status
  Bluetooth: hci_event: Fix checking for invalid handle on error status
====================

Link: https://lore.kernel.org/r/20220427234031.1257281-1-luiz.dentz@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Dylan Hung says:

====================
Add reset deassertion for Aspeed MDIO

Add missing reset deassertion for Aspeed MDIO bus controller. The reset
is asserted by the hardware when power-on so the driver only needs to
deassert it. To be able to work with the old DT blobs, the reset is
optional since it may be deasserted by the bootloader or the previous
kernel.

V6:
- fix merge conflict for net-next

V5:
- fix error of dt_binding_check

V4:
- use ASPEED_RESET_MII instead of hardcoding in dt-binding example

V3:
- remove reset property from the required list of the device tree
  bindings
- remove "Cc: stable@vger.kernel.org" from the commit messages
- add more description in the commit message of the dt-binding

V2:
- add reset property in the device tree bindings
- add reset assertion in the error path and driver remove
====================

Link: https://lore.kernel.org/r/20220427035501.17500-1-dylan_hung@aspeedtech.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Add reset control properties into MDIO nodes.  The 4 MDIO controllers in
AST2600 SOC share one reset control bit SCU50[3].
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add reset assertion/deassertion for Aspeed MDIO.  There are 4 MDIO
controllers embedded in Aspeed AST2600 SOC and share one reset control
register SCU50[3].  To work with old DT blobs which don't have the reset
property, devm_reset_control_get_optional_shared is used in this change.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The AST2600 MDIO bus controller has a reset control bit and must be
deasserted before manipulating the MDIO controller. By default, the
hardware asserts the reset so the driver only need to deassert it.

Regarding to the old DT blobs which don't have reset property in them,
the reset deassertion is usually done by the bootloader so the reset
property is optional to work with them.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Put device node in error path in fec_enet_init_stop_mode().

Fixes: 8a448bf8 ("net: ethernet: fec: move GPR register offset and bit into DT")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220426125231.375688-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/crash.

System message log shows the following:
=======================================
[ 3222.537510] EEH: Detected PCI bus error on PHB#384-PE#800000 [ 3222.537511] EEH: This PCI device has failed 2 times in the last hour and will be permanently disabled after 5 failures.
[ 3222.537512] EEH: Notify device drivers to shutdown [ 3222.537513] EEH: Beginning: 'error_detected(IO frozen)'
[ 3222.537514] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537516] bnx2x: [bnx2x_io_error_detected:14236(eth14)]IO error detected [ 3222.537650] EEH: PE#800000 (PCI 0384:80:00.0): bnx2x driver reports:
'need reset'
[ 3222.537651] EEH: PE#800000 (PCI 0384:80:00.1): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537651] bnx2x: [bnx2x_io_error_detected:14236(eth13)]IO error detected [ 3222.537729] EEH: PE#800000 (PCI 0384:80:00.1): bnx2x driver reports:
'need reset'
[ 3222.537729] EEH: Finished:'error_detected(IO frozen)' with aggregate recovery state:'need reset'
[ 3222.537890] EEH: Collect temporary log [ 3222.583481] EEH: of node=0384:80:00.0 [ 3222.583519] EEH: PCI device/vendor: 168e14e4 [ 3222.583557] EEH: PCI cmd/status register: 00100140 [ 3222.583557] EEH: PCI-E capabilities and status follow:
[ 3222.583744] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.583892] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.583893] EEH: PCI-E 20: 00000000 [ 3222.583893] EEH: PCI-E AER capability register set follows:
[ 3222.584079] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.584230] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.584378] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.584416] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.584416] EEH: of node=0384:80:00.1 [ 3222.584454] EEH: PCI device/vendor: 168e14e4 [ 3222.584491] EEH: PCI cmd/status register: 00100140 [ 3222.584492] EEH: PCI-E capabilities and status follow:
[ 3222.584677] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.584825] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.584826] EEH: PCI-E 20: 00000000 [ 3222.584826] EEH: PCI-E AER capability register set follows:
[ 3222.585011] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.585160] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.585309] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.585347] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.586872] RTAS: event: 5, Type: Platform Error (224), Severity: 2 [ 3222.586873] EEH: Reset without hotplug activity [ 3224.762767] EEH: Beginning: 'slot_reset'
[ 3224.762770] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->slot_reset()
[ 3224.762771] bnx2x: [bnx2x_io_slot_reset:14271(eth14)]IO slot reset initializing...
[ 3224.762887] bnx2x 0384:80:00.0: enabling device (0140 -> 0142) [ 3224.768157] bnx2x: [bnx2x_io_slot_reset:14287(eth14)]IO slot reset
--> driver unload

Uninterruptible tasks
=====================
crash> ps | grep UN
     213      2  11  c000000004c89e00  UN   0.0       0      0  [eehd]
     215      2   0  c000000004c80000  UN   0.0       0      0
[kworker/0:2]
    2196      1  28  c000000004504f00  UN   0.1   15936  11136  wickedd
    4287      1   9  c00000020d076800  UN   0.0    4032   3008  agetty
    4289      1  20  c00000020d056680  UN   0.0    7232   3840  agetty
   32423      2  26  c00000020038c580  UN   0.0       0      0
[kworker/26:3]
   32871   4241  27  c0000002609ddd00  UN   0.1   18624  11648  sshd
   32920  10130  16  c00000027284a100  UN   0.1   48512  12608  sendmail
   33092  32987   0  c000000205218b00  UN   0.1   48512  12608  sendmail
   33154   4567  16  c000000260e51780  UN   0.1   48832  12864  pickup
   33209   4241  36  c000000270cb6500  UN   0.1   18624  11712  sshd
   33473  33283   0  c000000205211480  UN   0.1   48512  12672  sendmail
   33531   4241  37  c00000023c902780  UN   0.1   18624  11648  sshd

EEH handler hung while bnx2x sleeping and holding RTNL lock
===========================================================
crash> bt 213
PID: 213    TASK: c000000004c89e00  CPU: 11  COMMAND: "eehd"
  #0 [c000000004d477e0] __schedule at c000000000c70808
  #1 [c000000004d478b0] schedule at c000000000c70ee0
  #2 [c000000004d478e0] schedule_timeout at c000000000c76dec
  #3 [c000000004d479c0] msleep at c0000000002120cc
  #4 [c000000004d479f0] napi_disable at c000000000a06448
                                        ^^^^^^^^^^^^^^^^
  #5 [c000000004d47a30] bnx2x_netif_stop at c0080000018dba94 [bnx2x]
  #6 [c000000004d47a60] bnx2x_io_slot_reset at c0080000018a551c [bnx2x]
  #7 [c000000004d47b20] eeh_report_reset at c00000000004c9bc
  #8 [c000000004d47b90] eeh_pe_report at c00000000004d1a8
  #9 [c000000004d47c40] eeh_handle_normal_event at c00000000004da64

And the sleeping source code
============================
crash> dis -ls c000000000a06448
FILE: ../net/core/dev.c
LINE: 6702

   6697  {
   6698          might_sleep();
   6699          set_bit(NAPI_STATE_DISABLE, &n->state);
   6700
   6701          while (test_and_set_bit(NAPI_STATE_SCHED, &n->state))
* 6702                  msleep(1);
   6703          while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state))
   6704                  msleep(1);
   6705
   6706          hrtimer_cancel(&n->timer);
   6707
   6708          clear_bit(NAPI_STATE_DISABLE, &n->state);
   6709  }

EEH calls into bnx2x twice based on the system log above, first through
bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes
the following call chains:

bnx2x_io_error_detected()
  +-> bnx2x_eeh_nic_unload()
       +-> bnx2x_del_all_napi()
            +-> __netif_napi_del()

bnx2x_io_slot_reset()
  +-> bnx2x_netif_stop()
       +-> bnx2x_napi_disable()
            +->napi_disable()

Fix this by correcting the sequence of NAPI APIs usage,
that is delete the NAPI after disabling it.

Fixes: 7fa6f340 ("bnx2x: AER revised")
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220426153913.6966-1-manishc@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf-next 2022-04-27

We've added 85 non-merge commits during the last 18 day(s) which contain
a total of 163 files changed, 4499 insertions(+), 1521 deletions(-).

The main changes are:

1) Teach libbpf to enhance BPF verifier log with human-readable and relevant
   information about failed CO-RE relocations, from Andrii Nakryiko.

2) Add typed pointer support in BPF maps and enable it for unreferenced pointers
   (via probe read) and referenced ones that can be passed to in-kernel helpers,
   from Kumar Kartikeya Dwivedi.

3) Improve xsk to break NAPI loop when rx queue gets full to allow for forward
   progress to consume descriptors, from Maciej Fijalkowski & Björn Töpel.

4) Fix a small RCU read-side race in BPF_PROG_RUN routines which dereferenced
   the effective prog array before the rcu_read_lock, from Stanislav Fomichev.

5) Implement BPF atomic operations for RV64 JIT, and add libbpf parsing logic
   for USDT arguments under riscv{32,64}, from Pu Lehui.

6) Implement libbpf parsing of USDT arguments under aarch64, from Alan Maguire.

7) Enable bpftool build for musl and remove nftw with FTW_ACTIONRETVAL usage
   so it can be shipped under Alpine which is musl-based, from Dominique Martinet.

8) Clean up {sk,task,inode} local storage trace RCU handling as they do not
   need to use call_rcu_tasks_trace() barrier, from KP Singh.

9) Improve libbpf API documentation and fix error return handling of various
   API functions, from Grant Seltzer.

10) Enlarge offset check for bpf_skb_{load,store}_bytes() helpers given data
    length of frags + frag_list may surpass old offset limit, from Liu Jian.

11) Various improvements to prog_tests in area of logging, test execution
    and by-name subtest selection, from Mykola Lysenko.

12) Simplify map_btf_id generation for all map types by moving this process
    to build time with help of resolve_btfids infra, from Menglong Dong.

13) Fix a libbpf bug in probing when falling back to legacy bpf_probe_read*()
    helpers; the probing caused always to use old helpers, from Runqing Yang.

14) Add support for ARCompact and ARCv2 platforms for libbpf's PT_REGS
    tracing macros, from Vladimir Isaev.

15) Cleanup BPF selftests to remove old & unneeded rlimit code given kernel
    switched to memcg-based memory accouting a while ago, from Yafang Shao.

16) Refactor of BPF sysctl handlers to move them to BPF core, from Yan Zhu.

17) Fix BPF selftests in two occasions to work around regressions caused by latest
    LLVM to unblock CI until their fixes are worked out, from Yonghong Song.

18) Misc cleanups all over the place, from various others.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (85 commits)
  selftests/bpf: Add libbpf's log fixup logic selftests
  libbpf: Fix up verifier log for unguarded failed CO-RE relos
  libbpf: Simplify bpf_core_parse_spec() signature
  libbpf: Refactor CO-RE relo human description formatting routine
  libbpf: Record subprog-resolved CO-RE relocations unconditionally
  selftests/bpf: Add CO-RE relos and SEC("?...") to linked_funcs selftests
  libbpf: Avoid joining .BTF.ext data with BPF programs by section name
  libbpf: Fix logic for finding matching program for CO-RE relocation
  libbpf: Drop unhelpful "program too large" guess
  libbpf: Fix anonymous type check in CO-RE logic
  bpf: Compute map_btf_id during build time
  selftests/bpf: Add test for strict BTF type check
  selftests/bpf: Add verifier tests for kptr
  selftests/bpf: Add C tests for kptr
  libbpf: Add kptr type tag macros to bpf_helpers.h
  bpf: Make BTF type match stricter for release arguments
  bpf: Teach verifier about kptr_get kfunc helpers
  bpf: Wire up freeing of referenced kptr
  bpf: Populate pairs of btf_id and destructor kfunc in btf
  bpf: Adapt copy_map_value for multiple offset case
  ...
====================

Link: https://lore.kernel.org/r/20220427224758.20976-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The mib counters for the ksz9477 is same for the ksz9477 switch and
LAN937x switch. Hence moving it to ksz_common.c file in order to have it
generic function. The DSA hook get_stats64 now can call ksz_get_stats64.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220426091048.9311-1-arun.ramadoss@microchip.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Calling tls_append_frag when max_open_record_len == record->len might
add an empty fragment to the TLS record if the call happens to be on the
page boundary. Normally tls_append_frag coalesces the zero-sized
fragment to the previous one, but not if it's on page boundary.

If a resync happens then, the mlx5 driver posts dump WQEs in
tx_post_resync_dump, and the empty fragment may become a data segment
with byte_count == 0, which will confuse the NIC and lead to a CQE
error.

This commit fixes the described issue by skipping tls_append_frag on
zero size to avoid adding empty fragments. The fix is not in the driver,
because an empty fragment is hardly the desired behavior.

Fixes: e8f69799 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220426154949.159055-1-maximmi@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf 2022-04-27

We've added 5 non-merge commits during the last 20 day(s) which contain
a total of 6 files changed, 34 insertions(+), 12 deletions(-).

The main changes are:

1) Fix xsk sockets when rx and tx are separately bound to the same umem, also
   fix xsk copy mode combined with busy poll, from Maciej Fijalkowski.

2) Fix BPF tunnel/collect_md helpers with bpf_xmit lwt hook usage which triggered
   a crash due to invalid metadata_dst access, from Eyal Birger.

3) Fix release of page pool in XDP live packet mode, from Toke Høiland-Jørgensen.

4) Fix potential NULL pointer dereference in kretprobes, from Adam Zabrocki.

   (Masami & Steven preferred this small fix to be routed via bpf tree given it's
    follow-up fix to Masami's rethook work that went via bpf earlier, too.)

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  xsk: Fix possible crash when multiple sockets are created
  kprobes: Fix KRETPROBES when CONFIG_KRETPROBE_ON_RETHOOK is set
  bpf, lwt: Fix crash when using bpf_skb_set_tunnel_key() from bpf_xmit lwt hook
  bpf: Fix release of page_pool in BPF_PROG_RUN in test runner
  xsk: Fix l2fwd for copy mode + busy poll combo
====================

Link: https://lore.kernel.org/r/20220427212748.9576-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge fixes from Andrew Morton:
 "Two patches.

  Subsystems affected by this patch series: mm/kasan and mm/debug"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  docs: vm/page_owner: use literal blocks for param description
  kasan: prevent cpu_quarantine corruption when CPU offline and cache shrink occur at same time

Sphinx generates hard-to-read lists of parameters at the bottom of the
page.  Fix them by putting literal-block markers of "::" in front of
them.

Link: https://lkml.kernel.org/r/cfd3bcc0-b51d-0c68-c065-ca1c4c202447@gmail.comSigned-off-by: Akira Yokosawa <akiyks@gmail.com>
Fixes: 57f2b54a ("Documentation/vm/page_owner.rst: update the documentation")
Cc: Shenghong Han <hanshenghong2019@email.szu.edu.cn>
Cc: Haowen Bai <baihaowen@meizu.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Alex Shi <seakeel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kasan_quarantine_remove_cache() is called in kmem_cache_shrink()/
destroy().  The kasan_quarantine_remove_cache() call is protected by
cpuslock in kmem_cache_destroy() to ensure serialization with
kasan_cpu_offline().

However the kasan_quarantine_remove_cache() call is not protected by
cpuslock in kmem_cache_shrink().  When a CPU is going offline and cache
shrink occurs at same time, the cpu_quarantine may be corrupted by
interrupt (per_cpu_remove_cache operation).

So add a cpu_quarantine offline flags check in per_cpu_remove_cache().

[akpm@linux-foundation.org: add comment, per Zqiang]

Link: https://lkml.kernel.org/r/20220414025925.2423818-1-qiang1.zhang@intel.comSigned-off-by: Zqiang <qiang1.zhang@intel.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The Sapphire Rapids (SPR) C6 optimization was added to the end of the
'spr_idle_state_table_update()' function. However, the function has a
'return' which may happen before the optimization has a chance to run.
And this may prevent the optimization from happening.

This is an unlikely scenario, but possible if user boots with, say,
the 'intel_idle.preferred_cstates=6' kernel boot option.

This patch fixes the issue by eliminating the problematic 'return'
statement.

Fixes: 3a9cf77b ("intel_idle: add core C6 optimization for SPR")
Suggested-by: Jan Beulich <jbeulich@suse.com>
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[ rjw: Minor changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>