This patch uses the previously added mcp251xfd_skb_set_timestamp()
function to convert the timestamp done by the CAN controller into a
proper skb hw timestamp.

Link: https://lore.kernel.org/r/20210304161209.2754463-1-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch add the HW timestamping infrastructure. The mcp251xfd has a
free running timer of 32 bit width, running at max 40MHz, which wraps
around every 107 seconds. The current timestamp is latched into RX and
TEF objects automatically be the CAN controller.

This patch sets up a cyclecounter, timecounter and delayed worker
infrastructure (which runs every 45 seconds) to convert the timer into
a proper 64 bit based ns timestamp.

Link: https://lore.kernel.org/r/20210304160328.2752293-6-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This is a preparation patch, it moves the mcp251xfd_get_timestamp()
function into the mcp251xfd.h file.

Link: https://lore.kernel.org/r/20210304160328.2752293-5-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The netdevice.h header is needed in mcp251xfd.h, so that it can be
included without further headers.

Link: https://lore.kernel.org/r/20210304160328.2752293-4-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In the patches:

| 1f652bb6 can: mcp25xxfd: rx-path: reduce number of SPI core requests to set UINC bit
| 68c0c1c7 can: mcp251xfd: tef-path: reduce number of SPI core requests to set UINC bit

the setting of the UINC bit in the TEF and RX FIFO was batched into a
single SPI message consisting of several transfers. All transfers but
the last need to have the cs_change set to 1.

In the original patches the array of prepared transfers is send from
the beginning with the length depending on the number of read TEF/RX
objects. The cs_change of the last transfer is temporarily set to
0 during send.

This patch removes the modification of cs_change by preparing the last
transfer with cs_change to 0 and all other to 1. When sending the SPI
message the driver now starts with an offset into the array, so that
it always ends on the last entry in the array, which has the cs_change
set to 0.

Link: https://lore.kernel.org/r/20210304160328.2752293-3-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

For easier debugging this patch adds dev coredump support to the
driver. A dev coredump is generated in case the chip fails to start or
an error in the interrupt handler is detected.

The dev coredump consists of all chip registers and chip memory, as
well as the driver's internal state of the TEF-, RX- and TX-FIFOs, it
can be analyzed with the mcp251xfd-dump tool of the can-utils:

https://github.com/linux-can/can-utils/tree/master/mcp251xfd
Link: https://lore.kernel.org/r/20210304160328.2752293-2-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

linux/regmap.h has been included at line 13, so remove the duplicate
one at line 14.

Fixes: 67def4ef ("can: tcan4x5x: move regmap code into seperate file")
Link: https://lore.kernel.org/r/20210323021026.140460-1-wanjiabing@vivo.comSigned-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

For peripheral devices, m_can sent skbs directly from a threaded irq
instead of from a softirq context, breaking the tcan4x5x peripheral
driver completely. This patch transitions the driver to use the
rx-offload helper for peripherals, ensuring the skbs are sent from the
correct context, with h/w timestamping to ensure correct ordering.

Link: https://lore.kernel.org/r/20210308102427.63916-4-torin@maxiluxsystems.comSigned-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
[mkl: m_can_class_register(): update error handling]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This is a prerequisite for transitioning the m_can driver to rx-offload,
which works best with TX and RX timestamps.

The timestamps provided by M_CAN are 16-bit, timed according to the
nominal bit timing, and may be prescaled by a multiplier up to 16. We
choose the highest prescalar so that the timestamp wraps every 2^20 bit
times, or 209 ms at a bus speed of 5 Mbit/s. Timestamps will have a
precision of 16 bit times.

Link: https://lore.kernel.org/r/20210308102427.63916-3-torin@maxiluxsystems.comSigned-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add infrastucture to allow internal timestamps from the M_CAN to be
configured and retrieved.

Link: https://lore.kernel.org/r/20210308102427.63916-2-torin@maxiluxsystems.comSigned-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

If the CAN net device has been successfully allocated, its private
data structure is impossible to be empty, remove this redundant error
return judgment.

Link: https://lore.kernel.org/r/20210205072559.13241-2-xulin.sun@windriver.comSigned-off-by: Xulin Sun <xulin.sun@windriver.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds "ONE-SHOT" mode support to the following CAN-USB
PEAK-System GmbH interfaces:
- PCAN-USB X6
- PCAN-USB FD
- PCAN-USB Pro FD
- PCAN-Chip USB
- PCAN-USB Pro
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: split into two patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch makes it possible to specifically flash the LED of a CAN
port of the CAN-USB interfaces of PEAK-System.

Link: https://lore.kernel.org/r/20210309122141.3276927-1-mkl@pengutronix.deSigned-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: use common prefix PCAN_ for defines]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch replaces the plain integers used for flags in
pcan_usb_pro_encode_msg() by macros which are already defined.

Link: https://lore.kernel.org/r/20210309082128.23125-4-s.grosjean@peak-system.comSigned-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: split into two patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

struct ucan_message_in contains member with 4-byte alignment
but is itself marked as unaligned, which triggers a warning:

drivers/net/can/usb/ucan.c:249:1: warning: alignment 1 of 'struct ucan_message_in' is less than 4 [-Wpacked-not-aligned]

Mark the outer structure to have the same alignment as the inner
one.

Link: https://lore.kernel.org/r/20210204162625.3099392-1-arnd@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Use already prepared dev_err_probe() introduced by commit a787e540
("driver core: add device probe log helper").
It simplifies EPROBE_DEFER handling.

Also unify message format for similar error cases.

Link: https://lore.kernel.org/r/91af0945ed7397b08f1af0c829450620bd92b804.1612442564.git.michal.simek@xilinx.comSigned-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

On ARCHs without IOMEM support the grcan driver fails to link due to
missing iomem functionality. This patch adds the missing Kconfig
dependency to HAS_IOMEM.

Link: https://lore.kernel.org/r/20210309140424.3331010-1-mkl@pengutronix.deReported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add three macro to simplify the readability of big bit timing numbers:
  - CAN_KBPS: kilobits per second (one thousand)
  - CAN_MBPS: megabits per second (one million)
  - CAN_MHZ: megahertz per second (one million)

Example:
	u32 bitrate_max = 8 * CAN_MBPS;
	struct can_clock clock = {.freq = 80 * CAN_MHZ};
instead of:
	u32 bitrate_max = 8000000;
	struct can_clock clock = {.freq = 80000000};

Apply the new macro to driver/net/can/dev/bittiming.c.

Link: https://lore.kernel.org/r/20210306054040.76483-1-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The logic for the tdco calculation is to just reuse the normal sample
point: tdco = sp. Because the sample point is expressed in tenth of
percent and the tdco is expressed in time quanta, a conversion is
needed.

At the end,
     ssp = tdcv + tdco
         = tdcv + sp.

Another popular method is to set tdco to the middle of the bit:
     tdc->tdco = can_bit_time(dbt) / 2
During benchmark tests, we could not find a clear advantages for one
of the two methods.

The tdco calculation is triggered each time the data_bittiming is
changed so that users relying on automated calculation can use the
netlink interface the exact same way without need of new parameters.
For example, a command such as:
	ip link set canX type can bitrate 500000 dbitrate 4000000 fd on
would trigger the calculation.

The user using CONFIG_CAN_CALC_BITTIMING who does not want automated
calculation needs to manually set tdco to zero.
For example with:
	ip link set canX type can tdco 0 bitrate 500000 dbitrate 4000000 fd on
(if the tdco parameter is provided in a previous command, it will be
overwritten).

If tdcv is set to zero (default), it is automatically calculated by
the transiver for each frame. As such, there is no code in the kernel
to calculate it.

tdcf has no automated calculation functions because we could not
figure out a formula for this parameter.

Link: https://lore.kernel.org/r/20210224002008.4158-6-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Fix the warning triggered by having an '=' at the beginning of the
line by moving it back to the previous line. Also replace all
indentations with a single space so that future entries can be more
easily added.

Extract of ./scripts/checkpatch.pl -f drivers/net/can/dev/netlink.c:

CHECK: Assignment operator '=' should be on the previous line
+       [IFLA_CAN_BITTIMING_CONST]
+                               = { .len = sizeof(struct can_bittiming_const) },

CHECK: Assignment operator '=' should be on the previous line
+       [IFLA_CAN_DATA_BITTIMING]
+                               = { .len = sizeof(struct can_bittiming) },

CHECK: Assignment operator '=' should be on the previous line
+       [IFLA_CAN_DATA_BITTIMING_CONST]
+                               = { .len = sizeof(struct can_bittiming_const) },

Link: https://lore.kernel.org/r/20210224002008.4158-4-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Save eight bytes of holes on x86-64 architectures by reordering struct
can_priv members.

Before:

$ pahole -C can_priv drivers/net/can/dev/dev.o
struct can_priv {
	struct net_device *        dev;                  /*     0     8 */
	struct can_device_stats    can_stats;            /*     8    24 */
	struct can_bittiming       bittiming;            /*    32    32 */
	/* --- cacheline 1 boundary (64 bytes) --- */
	struct can_bittiming       data_bittiming;       /*    64    32 */
	const struct can_bittiming_const  * bittiming_const; /*    96     8 */
	const struct can_bittiming_const  * data_bittiming_const; /*   104     8 */
	struct can_tdc             tdc;                  /*   112    12 */

	/* XXX 4 bytes hole, try to pack */

	/* --- cacheline 2 boundary (128 bytes) --- */
	const struct can_tdc_const  * tdc_const;         /*   128     8 */
	const u16  *               termination_const;    /*   136     8 */
	unsigned int               termination_const_cnt; /*   144     4 */
	u16                        termination;          /*   148     2 */

	/* XXX 2 bytes hole, try to pack */

	const u32  *               bitrate_const;        /*   152     8 */
	unsigned int               bitrate_const_cnt;    /*   160     4 */

	/* XXX 4 bytes hole, try to pack */

	const u32  *               data_bitrate_const;   /*   168     8 */
	unsigned int               data_bitrate_const_cnt; /*   176     4 */
	u32                        bitrate_max;          /*   180     4 */
	struct can_clock           clock;                /*   184     4 */
	enum can_state             state;                /*   188     4 */
	/* --- cacheline 3 boundary (192 bytes) --- */
	u32                        ctrlmode;             /*   192     4 */
	u32                        ctrlmode_supported;   /*   196     4 */
	u32                        ctrlmode_static;      /*   200     4 */
	int                        restart_ms;           /*   204     4 */
	struct delayed_work        restart_work;         /*   208   168 */

	/* XXX last struct has 4 bytes of padding */

	/* --- cacheline 5 boundary (320 bytes) was 56 bytes ago --- */
	int                        (*do_set_bittiming)(struct net_device *); /*   376     8 */
	/* --- cacheline 6 boundary (384 bytes) --- */
	int                        (*do_set_data_bittiming)(struct net_device *); /*   384     8 */
	int                        (*do_set_mode)(struct net_device *, enum can_mode); /*   392     8 */
	int                        (*do_set_termination)(struct net_device *, u16); /*   400     8 */
	int                        (*do_get_state)(const struct net_device  *, enum can_state *); /*   408     8 */
	int                        (*do_get_berr_counter)(const struct net_device  *, struct can_berr_counter *); /*   416     8 */
	unsigned int               echo_skb_max;         /*   424     4 */

	/* XXX 4 bytes hole, try to pack */

	struct sk_buff * *         echo_skb;             /*   432     8 */

	/* size: 440, cachelines: 7, members: 31 */
	/* sum members: 426, holes: 4, sum holes: 14 */
	/* paddings: 1, sum paddings: 4 */
	/* last cacheline: 56 bytes */
};

After:

$ pahole -C can_priv drivers/net/can/dev/dev.o
struct can_priv {
	struct net_device *        dev;                  /*     0     8 */
	struct can_device_stats    can_stats;            /*     8    24 */
	const struct can_bittiming_const  * bittiming_const; /*    32     8 */
	const struct can_bittiming_const  * data_bittiming_const; /*    40     8 */
	struct can_bittiming       bittiming;            /*    48    32 */
	/* --- cacheline 1 boundary (64 bytes) was 16 bytes ago --- */
	struct can_bittiming       data_bittiming;       /*    80    32 */
	const struct can_tdc_const  * tdc_const;         /*   112     8 */
	struct can_tdc             tdc;                  /*   120    12 */
	/* --- cacheline 2 boundary (128 bytes) was 4 bytes ago --- */
	unsigned int               bitrate_const_cnt;    /*   132     4 */
	const u32  *               bitrate_const;        /*   136     8 */
	const u32  *               data_bitrate_const;   /*   144     8 */
	unsigned int               data_bitrate_const_cnt; /*   152     4 */
	u32                        bitrate_max;          /*   156     4 */
	struct can_clock           clock;                /*   160     4 */
	unsigned int               termination_const_cnt; /*   164     4 */
	const u16  *               termination_const;    /*   168     8 */
	u16                        termination;          /*   176     2 */

	/* XXX 2 bytes hole, try to pack */

	enum can_state             state;                /*   180     4 */
	u32                        ctrlmode;             /*   184     4 */
	u32                        ctrlmode_supported;   /*   188     4 */
	/* --- cacheline 3 boundary (192 bytes) --- */
	u32                        ctrlmode_static;      /*   192     4 */
	int                        restart_ms;           /*   196     4 */
	struct delayed_work        restart_work;         /*   200   168 */

	/* XXX last struct has 4 bytes of padding */

	/* --- cacheline 5 boundary (320 bytes) was 48 bytes ago --- */
	int                        (*do_set_bittiming)(struct net_device *); /*   368     8 */
	int                        (*do_set_data_bittiming)(struct net_device *); /*   376     8 */
	/* --- cacheline 6 boundary (384 bytes) --- */
	int                        (*do_set_mode)(struct net_device *, enum can_mode); /*   384     8 */
	int                        (*do_set_termination)(struct net_device *, u16); /*   392     8 */
	int                        (*do_get_state)(const struct net_device  *, enum can_state *); /*   400     8 */
	int                        (*do_get_berr_counter)(const struct net_device  *, struct can_berr_counter *); /*   408     8 */
	unsigned int               echo_skb_max;         /*   416     4 */

	/* XXX 4 bytes hole, try to pack */

	struct sk_buff * *         echo_skb;             /*   424     8 */

	/* size: 432, cachelines: 7, members: 31 */
	/* sum members: 426, holes: 2, sum holes: 6 */
	/* paddings: 1, sum paddings: 4 */
	/* last cacheline: 48 bytes */
};

Link: https://lore.kernel.org/r/20210224002008.4158-3-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

At high bit rates, the propagation delay from the TX pin to the RX pin
of the transceiver causes measurement errors: the sample point on the
RX pin might occur on the previous bit.

This issue is addressed in ISO 11898-1 section 11.3.3 "Transmitter
delay compensation" (TDC).

This patch adds two new structures: can_tdc and can_tdc_const in order
to implement this TDC.

The structures are then added to can_priv.

A controller supports TDC if an only if can_priv::tdc_const is not
NULL.

TDC is active if and only if:
  - fd flag is on
  - can_priv::tdc.tdco is not zero.
It is the driver responsibility to check those two conditions are met.

No new controller modes are introduced (i.e. no CAN_CTRL_MODE_TDC) in
order not to be redundant with above logic.

The names of the parameters are chosen to match existing CAN
controllers specification. References:
  - Bosch C_CAN FD8:
https://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
  - Microchip CAN FD Controller Module:
http://ww1.microchip.com/downloads/en/DeviceDoc/MCP251XXFD-CAN-FD-Controller-Module-Family-Reference-Manual-20005678B.pdf
  - SAM E701/S70/V70/V71 Family:
https://www.mouser.com/datasheet/2/268/60001527A-1284321.pdf

Link: https://lore.kernel.org/r/20210224002008.4158-2-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In order to implement byte queue limits (bql) in CAN drivers, the
length of the CAN frame needs to be passed into the networking stack
even if the transmission failed for some reason.

To avoid to calculate this length twice, extend can_free_echo_skb() to
return that value. Convert all users of this function, too.

This patch is the natural extension of commit:

| 9420e1d4 ("can: dev: can_get_echo_skb(): extend to return can
|                frame length")

Link: https://lore.kernel.org/r/20210319142700.305648-3-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can: dev: can_free_echo_skb(): don't crash the kernel if can_priv::echo_skb is accessed out of bounds

A out of bounds access to "struct can_priv::echo_skb" leads to a
kernel crash. Better print a sensible warning message instead and try
to recover.

This patch is similar to:

| e7a6994d ("can: dev: __can_get_echo_skb(): Don't crash the kernel
|               if can_priv::echo_skb is accessed out of bounds")

Link: https://lore.kernel.org/r/20210319142700.305648-2-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

So far the creation of the TX echo skb was optional and can be
controlled by the local sender of a CAN frame.

It turns out that the TX echo CAN skb can be piggybacked to carry
information in the driver from the TX- to the TX-complete handler.

Several drivers already use the return value of
can_get_echo_skb() (which is the length of the data field in the CAN
frame) for their number of transferred bytes statistics. The
statistics are not working if CAN echo skbs are disabled.

Another use case is to calculate and set the CAN frame length on the
wire, which is needed for BQL support in both the TX and TX-completion
handler.

For now in can_put_echo_skb(), which is called from the TX handler,
the skb carrying the CAN frame is discarded if no TX echo is
requested, leading to the above illustrated problems.

This patch changes the can_put_echo_skb() function, so that the echo
skb is always generated. If the sender requests no echo, the echo skb
is consumed in __can_get_echo_skb() without being passed into the RX
handler of the networking stack, but the CAN data length and CAN frame
length information is properly returned.

Link: https://lore.kernel.org/r/20210309211904.3348700-1-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Update Chandrasekar Ramakrishnan as maintainer for mcan mmio device driver as I
will be moving to a different role.
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Dan Murphy's email address at ti.com doesn't work anymore, mails
bounce with:

| 550 Invalid recipient <dmurphy@ti.com> (#5.1.1)

For now remove all CAN related entries of Dan from the Maintainers
file.

Link: https://lore.kernel.org/r/20210228094218.40015-1-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add error handling in case of failure to send switching data path message
to the host.
Reported-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_min_tso_segs is now stored in u8, so max value is 255.

255 limit is enforced by proc_dou8vec_minmax().

We can therefore remove the gso_max_segs variable.

Fixes: 47996b489bdc ("tcp: convert elligible sysctls to u8")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]

Issue here is that:

- all dev_put() should be paired with a corresponding prior dev_hold().

- A driver doing a dev_put() in its ndo_uninit() MUST also
  do a dev_hold() in its ndo_init(), only when ndo_init()
  is returning 0.

Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.

Fixes: 919067cc ("net: add CONFIG_PCPU_DEV_REFCNT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]

Issue here is that:

- all dev_put() should be paired with a corresponding prior dev_hold().

- A driver doing a dev_put() in its ndo_uninit() MUST also
  do a dev_hold() in its ndo_init(), only when ndo_init()
  is returning 0.

Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.

Therefore, we need to move dev_hold() call from
vti6_tnl_create2() to vti6_dev_init_gen()

[1]
WARNING: CPU: 0 PID: 15951 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Modules linked in:
CPU: 0 PID: 15951 Comm: syz-executor.3 Not tainted 5.12.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Code: 1d 6a 5a e8 09 31 ff 89 de e8 8d 1a ab fd 84 db 75 e0 e8 d4 13 ab fd 48 c7 c7 a0 e1 c1 89 c6 05 4a 5a e8 09 01 e8 2e 36 fb 04 <0f> 0b eb c4 e8 b8 13 ab fd 0f b6 1d 39 5a e8 09 31 ff 89 de e8 58
RSP: 0018:ffffc90001eaef28 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000040000 RSI: ffffffff815c51f5 RDI: fffff520003d5dd7
RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff815bdf8e R11: 0000000000000000 R12: ffff88801bb1c568
R13: ffff88801f69e800 R14: 00000000ffffffff R15: ffff888050889d40
FS:  00007fc79314e700(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f1c1ff47108 CR3: 0000000020fd5000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 __refcount_dec include/linux/refcount.h:344 [inline]
 refcount_dec include/linux/refcount.h:359 [inline]
 dev_put include/linux/netdevice.h:4135 [inline]
 vti6_dev_uninit+0x31a/0x360 net/ipv6/ip6_vti.c:297
 register_netdevice+0xadf/0x1500 net/core/dev.c:10308
 vti6_tnl_create2+0x1b5/0x400 net/ipv6/ip6_vti.c:190
 vti6_newlink+0x9d/0xd0 net/ipv6/ip6_vti.c:1020
 __rtnl_newlink+0x1062/0x1710 net/core/rtnetlink.c:3443
 rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3491
 rtnetlink_rcv_msg+0x44e/0xad0 net/core/rtnetlink.c:5553
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
 netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
 netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 ____sys_sendmsg+0x331/0x810 net/socket.c:2350
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2404
 __sys_sendmmsg+0x195/0x470 net/socket.c:2490
 __do_sys_sendmmsg net/socket.c:2519 [inline]
 __se_sys_sendmmsg net/socket.c:2516 [inline]
 __x64_sys_sendmmsg+0x99/0x100 net/socket.c:2516
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]

Issue here is that:

- all dev_put() should be paired with a corresponding dev_hold(),
  and vice versa.

- A driver doing a dev_put() in its ndo_uninit() MUST also
  do a dev_hold() in its ndo_init(), only when ndo_init()
  is returning 0.

Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.

ip6_gre for example (among others problematic drivers)
has to use dev_hold() in ip6gre_tunnel_init_common()
instead of from ip6gre_newlink_common(), covering
both ip6gre_tunnel_init() and ip6gre_tap_init()/

Note that ip6gre_tunnel_init_common() is not called from
ip6erspan_tap_init() thus we also need to add a dev_hold() there,
as ip6erspan_tunnel_uninit() does call dev_put()

[1]
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 0 PID: 8422 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Modules linked in:
CPU: 1 PID: 8422 Comm: syz-executor854 Not tainted 5.12.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Code: 1d 6a 5a e8 09 31 ff 89 de e8 8d 1a ab fd 84 db 75 e0 e8 d4 13 ab fd 48 c7 c7 a0 e1 c1 89 c6 05 4a 5a e8 09 01 e8 2e 36 fb 04 <0f> 0b eb c4 e8 b8 13 ab fd 0f b6 1d 39 5a e8 09 31 ff 89 de e8 58
RSP: 0018:ffffc900018befd0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88801ef19c40 RSI: ffffffff815c51f5 RDI: fffff52000317dec
RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff815bdf8e R11: 0000000000000000 R12: ffff888018cf4568
R13: ffff888018cf4c00 R14: ffff8880228f2000 R15: ffffffff8d659b80
FS:  00000000014eb300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055d7bf2b3138 CR3: 0000000014933000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 __refcount_dec include/linux/refcount.h:344 [inline]
 refcount_dec include/linux/refcount.h:359 [inline]
 dev_put include/linux/netdevice.h:4135 [inline]
 ip6gre_tunnel_uninit+0x3d7/0x440 net/ipv6/ip6_gre.c:420
 register_netdevice+0xadf/0x1500 net/core/dev.c:10308
 ip6gre_newlink_common.constprop.0+0x158/0x410 net/ipv6/ip6_gre.c:1984
 ip6gre_newlink+0x275/0x7a0 net/ipv6/ip6_gre.c:2017
 __rtnl_newlink+0x1062/0x1710 net/core/rtnetlink.c:3443
 rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3491
 rtnetlink_rcv_msg+0x44e/0xad0 net/core/rtnetlink.c:5553
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
 netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
 netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2350
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2404
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2433
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46

Fixes: 919067cc ("net: add CONFIG_PCPU_DEV_REFCNT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We fix a warning from the htmldoc tool and an indentation error reported
by smatch. There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
1GbE Intel Wired LAN Driver Updates 2021-03-29

This series contains updates to igc driver only.

Andre Guedes says:

Add XDP support for the igc driver. The approach implemented by this
series follows the same approach implemented in other Intel drivers as
much as possible for the sake of consistency.

The series is organized in two parts. In the first part, i.e. patches
from 1 to 4, igc_main.c and igc_ptp.c code is refactored in preparation
for landing the XDP support, which is introduced in the second part
(patches from 5 to 8).

As far as code organization is concerned, XDP-related helpers are
defined in a new file, igc_xdp.c, and are called by igc_main.c.

The features added by this series have been tested with the samples
provided in samples/bpf/: xdp1, xdp2, xdp_redirect_cpu, and
xdp_redirect_map.

Upcoming series will add support of UMEM and zero-copy features from
AF_XDP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

MBIM protocol makes the mhi network interface asymmetric, ingress data
received from MHI is MBIM protocol, possibly containing multiple
aggregated IP packets, while egress data received from network stack is
IP protocol.

This changes allows a 'protocol' to specify its own MRU, that when
specified is used to allocate MHI RX buffers (skb).

For MBIM, Set the default MTU to 1500, which is the usual network MTU
for WWAN IP packets, and MRU to 3.5K (for allocation efficiency),
allowing skb to fit in an usual 4K page (including padding,
skb_shared_info, ...).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, if skb is non-linear, due to MHI skb chaining, it is
linearized in MBIM RX handler prior MBIM decoding, causing extra
allocation and copy that can be as large as the maximum MBIM frame
size (32K).

This change introduces MBIM decoding for non-linear skb, allowing to
process 'large' non-linear MBIM packets without skb linearization.
The IP packets are simply extracted from the MBIM frame using the
skb_copy_bits helper.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable res is being initialized with a value that is
never read and it is being updated later with a new value.
The initialization is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a document describing the principles behind resilient next-hop groups,
and some notes about how to configure and offload them.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following make W=1 kernel build warning:

 drivers/net/mdio.c:95: warning: expecting prototype for mdio_link_ok(). Prototype was for mdio45_links_ok() instead
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following make W=1 kernel build warning:

 drivers/net/bonding/bond_main.c:982: warning: expecting prototype for change_active_interface(). Prototype was for bond_change_active_slave() instead
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>