- 17 Mar, 2009 4 commits
-
-
Bjorn Helgaas authored
We don't need a struct containing a count and a list_head; a simple list_head is sufficient. The list iterators handle empty lists fine. Furthermore, we don't need to check for null list entries because we only add non-null entries. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
-
Bjorn Helgaas authored
Better to oops and learn about a bug than to silently cover it up. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
-
Bjorn Helgaas authored
Remove unnecessary casts and initializations. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
-
Bjorn Helgaas authored
This patch makes whitespace and indentation more consistent. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
-
- 25 Feb, 2009 17 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/i915: convert DRM_ERROR to DRM_DEBUG in phys object pwrite path drm/i915: make hw page ioremap use ioremap_wc drm: edid revision 0 is valid drm: Correct unbalanced drm_vblank_put() during mode setting. drm: disable encoders before re-routing them drm: Fix ordering of bit fields in EDID structure leading huge vsync values. drm: Fix shifts of EDID vsync offset/width fields. drm/i915: handle bogus VBT panel timing drm/i915: remove PLL debugging messages
-
git://neil.brown.name/mdLinus Torvalds authored
* 'for-linus' of git://neil.brown.name/md: md: avoid races when stopping resync. md/raid10: Don't call bitmap_cond_end_sync when we are doing recovery. md/raid10: Don't skip more than 1 bitmap-chunk at a time during recovery.
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc64: Fix crashes in jbusmc_print_dimm()
-
git://git.infradead.org/iommu-2.6Linus Torvalds authored
* git://git.infradead.org/iommu-2.6: intel-iommu: fix endless "Unknown DMAR structure type" loop VT-d: handle Invalidation Queue Error to avoid system hang intel-iommu: fix build error with INTR_REMAP=y and DMAR=n
-
Fenghua Yu authored
When iwlan runs on IOMMU, IOMMU generates a lot of PTE write faults because PTE write bit is not set on some of PTE's. This is because iwlan driver calls DMA mapping with PCI_DMA_TODEVICE which is read only in mapping PTE. But iwlan device actually writes to the mapped page to update its contents. This issue is not exposed in swiotlb. But VT-d hardware can capture this fault and stop the fault transaction. The following patch fixes the issue. Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Reviewed-by: Bhavesh Davda <bhavesh@vmware.com> Tested-by: Chris Wright <chrisw@sous-sol.org> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Dave Airlie authored
This snuck in when I wrote phys object support. Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Dave Airlie authored
However we still have another issue with ioremap_wc not falling back properly or somehow doing something else stupid, this probably needs to be tracked down. Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Kyle McMartin authored
edid->revision == 0 should be valid (at least, so the error message indicates. :) and wikipedia seems to indicate that EDID 1.0 existed. We can dump the entire check, since edid->revision is a u8, so it can't ever be less than 0. Marko reports in RH bz#476735 that his monitor claims to be EDID 1.0, and therefore hits the check and is stuck at 800x600 because of it. Reported-by: Marko Ristola <marko.ristola@kolumbus.fi> Signed-off-by: Kyle McMartin <kyle@redhat.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Dave Airlie <airlied@linux.ie>
-
Chris Wilson authored
The first time we install a mode, the vblank will be disabled for a pipe and so drm_vblank_get() in drm_vblank_pre_modeset() will fail. As we unconditionally call drm_vblank_put() afterwards, the vblank reference counter becomes unbalanced. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Dave Airlie <airlied@linux.ie>
-
Jesse Barnes authored
In some cases we may receive a mode config that has a different CRTC<->encoder map that the current configuration. In that case, we need to disable any re-routed encoders before setting the mode, otherwise they may not pick up the new CRTC (if the output types are incompatible for example). Tested-by: Kristian Høgsberg <krh@bitplanet.net> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Dave Airlie <airlied@linux.ie>
-
Jesse Barnes authored
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
-
Linus Torvalds authored
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
-
Jesse Barnes authored
We've seen cases in the wild where the VBT sync data is wrong, so add some code to fix it up in that case, taking care to make sure that the total is greater than the sync end. Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Dave Airlie <airlied@linux.ie>
-
Jesse Barnes authored
These are normal; we walk through different values looking for the right one, so why flood the screen with messages? Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@linux.ie>
-
NeilBrown authored
There has been a race in raid10 and raid1 for a long time which has only recently started showing up due to a scheduler changed. When a sync_read request finishes, as soon as reschedule_retry is called, another thread can mark the resync request as having completed, so md_do_sync can finish, ->stop can be called, and ->conf can be freed. So using conf after reschedule_retry is not safe. Similarly, when finishing a sync_write, calling md_done_sync must be the last thing we do, as it allows a chain of events which will free conf and other data structures. The first of these requires action in raid10.c The second requires action in raid1.c and raid10.c Cc: stable@kernel.org Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
For raid1/4/5/6, resync (fixing inconsistencies between devices) is very similar to recovery (rebuilding a failed device onto a spare). The both walk through the device addresses in order. For raid10 it can be quite different. resync follows the 'array' address, and makes sure all copies are the same. Recover walks through 'device' addresses and recreates each missing block. The 'bitmap_cond_end_sync' function allows the write-intent-bitmap (When present) to be updated to reflect a partially completed resync. It makes assumptions which mean that it does not work correctly for raid10 recovery at all. In particularly, it can cause bitmap-directed recovery of a raid10 to not recovery some of the blocks that need to be recovered. So move the call to bitmap_cond_end_sync into the resync path, rather than being in the common "resync or recovery" path. Cc: stable@kernel.org Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When doing recovery on a raid10 with a write-intent bitmap, we only need to recovery chunks that are flagged in the bitmap. However if we choose to skip a chunk as it isn't flag, the code currently skips the whole raid10-chunk, thus it might not recovery some blocks that need recovering. This patch fixes it. In case that is confusing, it might help to understand that there is a 'raid10 chunk size' which guides how data is distributed across the devices, and a 'bitmap chunk size' which says how much data corresponds to a single bit in the bitmap. This bug only affects cases where the bitmap chunk size is smaller than the raid10 chunk size. Cc: stable@kernel.org Signed-off-by: NeilBrown <neilb@suse.de>
-
- 24 Feb, 2009 19 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/procLinus Torvalds authored
* 'proc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc: proc: fix PG_locked reporting in /proc/kpageflags
-
git://jdelvare.pck.nerim.net/jdelvare-2.6Linus Torvalds authored
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: Add i2c_board_info for RiscPC PCF8583 i2c: Make sure i2c_algo_bit_data.timeout is HZ-independent i2c-dev: Clarify the unit of ioctl I2C_TIMEOUT i2c: Timeouts reach -1 i2c: Fix misplaced parentheses
-
Linus Torvalds authored
Merge branch 'firedtv-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'firedtv-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: firedtv: dvb_frontend_info for FireDTV S2, fix "frequency limits undefined" error firedtv: massive refactoring firedtv: rename files, variables, functions from firesat to firedtv firedtv: Use DEFINE_SPINLOCK firedtv: fix registration - adapter number could only be zero firedtv: use length_field() of PMT as length firedtv: fix returned struct for ca_info firedtv: cleanups and minor fixes ieee1394: remove superfluous assertions ieee1394: inherit ud vendor_id from node vendor_id ieee1394: add hpsb_node_read() and hpsb_node_lock() ieee1394: use correct barrier types between accesses of nodeid and generation firesat: copyrights, rename to firedtv, API conversions, fix remote control input firesat: avc resend firesat: update isochronous interface, add CI support firesat: add DVB-S support for DVB-S2 devices firesat: fix DVB-S2 device recognition DVB: add firesat driver
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: Fix deadlock in ext4_write_begin() and ext4_da_write_begin() ext4: Add fallback for find_group_flex
-
Russell King authored
Add the necessary i2c_board_info structure to fix the lack of PCF8583 RTC on RiscPC. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Alessandro Zummo <a.zummo@towertech.it>
-
Jean Delvare authored
i2c_algo_bit_data.timeout is supposed to be in jiffies, so drivers should use set this value in terms of HZ. Ultimately I think this field should be discarded in favor of i2c_adapter.timeout, but that's left for a future patch. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Lennert Buytenhek <kernel@wantstofly.org> Acked-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
-
Jean Delvare authored
The unit in which user-space can set the bus timeout value is jiffies for historical reasons (back when HZ was always 100.) This is however not good because user-space doesn't know how long a jiffy lasts. The timeout value should instead be set in a fixed time unit. Given the original value of HZ, this unit should be 10 ms, for compatibility. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Wolfram Sang <w.sang@pengutronix.de>
-
Roel Kluin authored
With a postfix decrement these timeouts reach -1 rather than 0, but after the loop it is tested whether they have become 0. As pointed out by Jean Delvare, the condition we are waiting for should also be tested before the timeout. With the current order, you could exit with a timeout error while the job is actually done. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
-
Roel Kluin authored
Fix misplaced parentheses. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
-
Helge Bahmann authored
Expr always evaluates to zero. Cc: Matt Mackall <mpm@selenic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
-
Beat Michel Liechti authored
I found that the function fdtv_frontend_init in the file firedtv-fe.c was missing a case for FIREDTV_DVB_S2 which resulted in "frequency limits undefined" errors in syslog. Signed-off-by: Beat Michel Liechti <bml303@gmail.com> Change by Stefan R: combine it with case case FIREDTV_DVB_S as originally suggested by Beat Michel. This enables FE_CAN_FEC_AUTO also for FireDTV-S2 devices which is possible as long as only DVB-S channels are used. FE_CAN_FEC_AUTO would be wrong for DVB-S2 channels, but those cannot be used yet since the driver is not yet converted to S2API. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Combination of the following changes: Mon, 23 Feb 2009 14:21:10 +0100 (CET) firedtv: reinstate debug logging option Henrik Kurelid tells me that FCP debug logging (which I removed during cleanups) is still useful when working on driver issues together with end users. So bring it back in an updated form with only 60% of the original code footprint. Logging can be enabled with # echo -1 > /sys/module/firedtv/parameters/debug 1 instead of -1 enables only FCP header logging, 2 instead of -1 enables only hexdumps of the entire FCP frames. 0 switches logging off again. Fri, 20 Feb 2009 20:54:27 +0100 (CET) firedtv: build fix for INPUT=m and DVB_FIREDTV=y Thu, 19 Feb 2009 20:40:39 +0100 firedtv: use msecs_to_jiffies Pointed out by Mauro Carvalho Chehab. Sun Feb 15 20:50:46 CET 2009 firedtv: some more housekeeping Fix an old checkpatch warning and a new compiler warning. Sun Feb 15 15:33:17 CET 2009 firedtv: rename a file once more At the moment, about a third of avc.c is specific to FireDTVs rather than generic AV/C code. Rename it to firedtv-avc.c. Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: more compact channels backing store Replace struct firedtv_channel { bool active; int pid; } channel[16]; by unsigned long channel_active; u16 channel_pid[16];. Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: some simplifications c->active was unnecessarily cleared twice. Also, by marking the channel inactive before the for loop, the loop becomes identical with fdtv_channel_collect(). Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: remove a bogus loop This loop is unnecessary because - only active channel[].pid's will be sent to the device, - when a channel is activated, its pid is set to dvbdmxfeed->pid. Perhaps the original code was there because it was initially not fully covered by the fdtv->demux_mutex. Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: fix mutex protection fdtv_start_feed() accessed the channel list unsafely. Fully serialize it with itself and fdtv_stop_feed(). Sun Feb 15 15:33:17 CET 2009 firedtv: dvb demux: fix missing braces Original code was: ... case DMX_TS_PES_OTHER: //Dirty fix to keep firesat->channel pid-list up to date for(k=0;k<16;k++){ if(firesat->channel[k].active == 0) firesat->channel[k].pid = dvbdmxfeed->pid; break; } channel = firesat_channel_allocate(firesat); break; default: ... Looks bogus in several respects. For now let's just add braces to the if because that seems to be what the author meant. Sun Feb 15 15:33:17 CET 2009 firedtv: allow build without input subsystem !CONFIG_INPUT is very unlikely on systems on which firedtv is of interest. But we can easily support it. Sun Feb 15 15:33:17 CET 2009 firedtv: replace EXTRA_CFLAGS by ccflags The former are deprecated. The latter can depend on Kconfig variables. Sun Feb 15 15:33:17 CET 2009 firedtv: concentrate ieee1394 dependencies Move the entire interface with drivers/ieee1394 to firedtv-1394.c. Move 1394-independent module initialization code to firedtv-dvb.c. This prepares interfacing with drivers/firewire. Sun Feb 15 15:33:17 CET 2009 firedtv: amend Kconfig menu prompt Sun Feb 15 15:33:17 CET 2009 firedtv: remove kernel version compatibility macro Sun Feb 15 15:33:17 CET 2009 firedtv: combine header files avc.h and firedtv-*.h are small and currently not shared with other drivers, hence concatenate them all into firedtv.h. Sun Feb 15 15:33:17 CET 2009 firedtv: misc style touch-ups Standardize on lower-case hexadecimal constants. Adjust whitespace. Omit unnecessary pointer type casts and an unnecessary list head initialization. Use dev_printk. Wed Feb 11 21:21:04 CET 2009 firedtv: avc, ci: remove unused constants Wed Feb 11 21:21:04 CET 2009 firedtv: avc: remove bitfields from read descriptor response operands Don't use bitfields in struct types of on-the-wire data. Wed Feb 11 21:21:04 CET 2009 firedtv: avc: remove bitfields from DSD command operands Don't use bitfields in struct types of on-the-wire data. Wed Feb 11 21:21:04 CET 2009 firedtv: avc: header file cleanup Remove unused constants and declarations. Move privately used constants into .c files. Wed Feb 11 21:21:04 CET 2009 firedtv: avc: remove bitfields from FCP frame types Don't use bitfields in struct types of on-the-wire data. Also move many privately used constants from avc.h to avc.c and remove some unused constants. Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: avc: fix offset in avc_tuner_get_ts The parentheses were wrong. It didn't matter though because this code only writes a 0 into an area which is already initialized to 0. Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: avc: reduce stack usage, remove two typedefs It is safe to share a memory buffer for command frame and response frame because the response data come in after the command frame was last used. Even less stack would be required if only the actual required frame size instead of the entire FCP register size was allocated. Also, rename the defined types AVCCmdFrm and AVCRspFrm to struct avc_command_frame and struct avc_response_frame. TODO: Remove the bitfields in these types. Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: cmp: move code to avc Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: iso: move code to firedtv-1394 Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: iso: remove unnecessary struct type definitions Sun, 18 Jan 2009 16:30:00 +0100 (CET) firedtv: iso: style changes and fixlets Add cleanup after failure in setup_iso_channel. Replace printk() by dv_err(). Decrease indentation level in rawiso_activity_cb(). Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Rambaldi authored
Combination of the following changes: Sat, 17 Jan 2009 14:47:34 +0100 firedtv: rename variables and functions from firesat to firedtv Signed-off-by: Rambaldi <Rambaldi@xs4all.nl> Additional changes by Stefan Richter: Renamed struct firedtv *firedtv to struct firedtv *fdtv and firedtv_foo_bar() to fdtv_foo_bar() for brevity. Sat, 17 Jan 2009 13:07:44 +0100 firedtv: rename files from firesat to firedtv Signed-off-by: Rambaldi <Rambaldi@xs4all.nl> Additional changes by Stefan Richter: Name the directory "firewire" instead of "firedtv". Standardize on "-" instead of "_" in file names, because that's what drivers/firewire/ and drivers/media/dvb/dvb-usb/ use too. Build fix. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Julia Lawall authored
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested in Documentation/spinlocks.txt Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Henrik Kurelid authored
There was a bug causing the initialization to fail if adapter number was greater than zero. The adapter was however registered which caused the driver to oops the second time initialization was tried. Signed-off-by: Henrik Kurelid <henrik@kurelid.se> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Henrik Kurelid authored
Parsed and used the length_field() of the PMT message instead of using the length field of the message struct, which does not seem to be filled correctly by e.g. MythTV. Signed-off-by: Henrik Kurelid <henrik@kurelid.se> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Henrik Kurelid authored
The SystemId of the ca_info message was filled with garbage. It now returns what the card returns. Signed-off-by: Henrik Kurelid <henrik@kurelid.se> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
Combination of the following changes: Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: increase FCP frame length for DVB-S2 tune QSPK The last three bytes didn't go out to the wire. Effect of the fix not yet tested. Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: replace mdelay by msleep These functions can sleep (and in fact sleep for the duration of a whole FCP transaction). Hence msleep is more appropriate here. Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: trivial reorganization in avc_api Reduce nesting level by factoring code out of avc_tuner_dsd() into helper functions. Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: trivial cleanups in avc_api Use dev_err(), no CamelCase function names, adjust comment style, put #if 0 around unused code and add FIXME comments, standardize on lower-case hexadecimal constants, use ALIGN() for some frame length calculations, make a local function static... The code which writes FCP command frames and reads FCP response frames is not yet brought into canonical kernel coding style because this involves changes of typedefs (on-the-wire bitfields). Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: don't retry oPCR updates endlessly In the theoretical case that the target node wasn't handling the lock transactions as expected or there was continued interference by other initiating nodes, these functions wouldn't return for ages. Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: remove bitfield typedefs from cmp, fix for big endian CPUs Use macros/ inline functions/ standard byte order accessors to read and write oPCR register values (big endian bitfields, on-the-wire data). The new code may not be the ultimate optimum, but it doesn't occur in a hot path. This fixes the CMP code for big endian CPUs. So far I tested it only on a little endian CPU though. For now, include <asm/byteorder.h> instead of <linux/byteorder.h> because drivers/ieee1394/*.h also include the former. I will fix this in drivers/ieee1394 and firedtv later. Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: trivial cleanups in cmp Reduce nesting level by means of early exit and goto. Remove obsolete includes, use dev_err(), no CamelCase function names... Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: trivial cleanups in firesat-ci Whitespace, variable names, comment style... Also, use dvb_generic_open() and dvb_generic_release() directly as our hooks in struct file_operations because firedtv's wrappers merely called these generic functions. Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: remove CA debug code This looks like it is not necessary to have available for endusers who cannot patch kernels for bug reporting and tests of fixes. Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: remove AV/C debug code This looks like it is not necessary to have available for endusers who cannot patch kernels for bug reporting and tests of fixes. Sun, 2 Nov 2008 13:45:00 +0100 (CET) firedtv: remove various debug code Most of this was already commented out. And that which wasn't is not relevant in normal use. Mon, 29 Sep 2008 19:22:48 +0200 (CEST) firedtv: register input device as child of a FireWire device Instead of one virtual input device which exists for the whole lifetime of the driver and receives events from all connected FireDTVs, register one input device for each firedtv device. These input devices will show up as children of the respective firedtv devices in the sysfs hierarchy. However, the implementation falls short because of a bug in userspace: Udev's path_id script gets stuck with 100% CPU utilization, maybe because of an assumption about the maximum ieee1394 device hierarchy depth. To avoid this bug, we use the fw-host device instead of the proper unit_directory device as parent of the input device. There is hope that the port to the new firewire stack won't be inhibited by this userspace bug because there are no fw-host devices there. Mon, 29 Sep 2008 19:21:52 +0200 (CEST) firedtv: fix string comparison and a few sparse warnings Sparse found a bug: while ((kv_buf + kv_len - 1) == '\0') should have been while (kv_buf[kv_len - 1] == '\0') We fix it by a better implementation without a temporary copy. Also fix sparse warnings of 0 instead of NULL and signedness mismatches. Mon, 29 Sep 2008 19:21:20 +0200 (CEST) firedtv: remove unused struct members and redefine an int as a bool. Mon, 29 Sep 2008 19:20:36 +0200 (CEST) firedtv: fix initialization of dvb_frontend.ops There was a NULL pointer reference if no dvb_frontend_info was found. Also, don't directly assign struct typed values to struct typed variables. Instead write out assignments to individual strcut members. This reduces module size by about 1 kB. Mon, 29 Sep 2008 19:19:41 +0200 (CEST) firedtv: remove unused dual subunit code from initialization No FireDTVs with more than one subunit exists, hence simplify the initialization for the special case of one subunit. The driver was able to check for more than one subunit but was broken for more than two subunits. While we are at it, add several missing cleanups after failure, and include a few dynamically allocated structures diretly into struct firesat instead of allocating them separately. Mon, 29 Sep 2008 19:19:08 +0200 (CEST) firedtv: add vendor_id and version to driver match table Now that nodemgr was enhanced to match against the root directory's vendor ID if there isn't one in the unit directory, use this to prevent firedtv to be bound to wrong devices by accident. Also add the AV/C software version ID to the match flags for completeness; specifier ID and software only make sense as a pair. Mon, 29 Sep 2008 19:18:30 +0200 (CEST) firedtv: use hpsb_node_read(), _write(), _lock() because they are simpler and treat the node generation more correctly. While we are at it, clean up and simplify surrounding code. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Stefan Richter authored
hpsb_read, hpsb_write, hpsb_lock are sleeping functions which nobody is in danger to use in atomic context. Besides, in_interrupt does not cover all types of atomic context. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
-