The ARM CPU cores are fed by the CPU clock from the CCU. Add a
reference to the clock for each CPU core, along with the clock
transition latency.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-5-wens@kernel.org

The Bananapi M2+ uses a GPIO line to change the effective resistance of
the CPU supply regulator's feedback resistor network. The voltages
described in the device tree were given directly by the vendor. This
turns out to be slightly off compared to the real values.

The updated voltages are based on calculations of the feedback resistor
network, and verified down to three decimal places with a multi-meter.

Fixes: 6eeb4180 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-4-wens@kernel.org

The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.

Assign the same regulator supply to the remaining CPU cores to address
this.

Fixes: 6eeb4180 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-3-wens@kernel.org

The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.

Assign the same regulator supply to the remaining CPU cores to address
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-2-wens@kernel.org

Some outputs from the RTL8723CS are connected to the PL port (BT_WAKE_AP),
which runs at 1.8V. When BT_WAKE_AP is high, the PL pin this signal is
connected to is overdriven, and the whole PL port's voltage rises
somewhat. This results in changing voltage on the R_PWM pin (PL10),
which is the cause for backlight flickering very noticeably when typing
on a Bluetooth keyboard, because backlight intensity is highly sensitive
to the voltage of the R_PWM pin.

Limit the maximum WiFi/BT I/O voltage to 1.8V to avoid overdriving
the PL port pins via BT and WiFi IO port signals. WiFi and BT
functionality is unaffected by this change.

This completely stops the backlight flicker when using bluetooth.

Fixes: 91f480d4 ("arm64: dts: allwinner: Add initial support for Pine64 PinePhone")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20200703194842.111845-4-megous@megous.comSigned-off-by: Maxime Ripard <maxime@cerno.tech>

Revision 1.2 should be the final production version of the PinePhone.
It has most of the known HW quirks fixed.

Interrupt to the magnetometer is routed correctly, in this revision.

The bulk of the changes are in how modem and the USB-C HDMI bridge
chip is powered and where the signals from the modem are connected.

Also backlight intensity seemingly behaves differently, than on the
1.1 and 1.0 boards, and the PWM duty cycle where backlight starts
to work is 10% (as tested on 2 1.2 PinePhones I have access to).
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20200703194842.111845-3-megous@megous.comSigned-off-by: Maxime Ripard <maxime@cerno.tech>

Document board compatible names for Pine64 PinePhone 1.2.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20200703194842.111845-2-megous@megous.comSigned-off-by: Maxime Ripard <maxime@cerno.tech>

Pinephone has a Goodix GT917S capacitive touchscreen controller on
I2C0 bus. Add support for it.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200702081432.1727696-3-megous@megous.com
[Maxime: Removed the redundant pinctrl nodes]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

PinePhone uses PWM backlight and a XBD599 LCD panel over DSI for
display.

Backlight levels curve was optimized by Martijn Braam using a
lux meter.

Add its device nodes.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200702081432.1727696-2-megous@megous.comSigned-off-by: Maxime Ripard <maxime@cerno.tech>

Add pwr and status leds configuration and turn on pwr led by default for Orange
Pi Zero Plus 2 (both H3 and H5 variants).
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Link: https://lore.kernel.org/r/20200615130223.34464-2-diego.rondini@kynetics.comSigned-off-by: Maxime Ripard <maxime@cerno.tech>

Enable support for USB OTG port on Orange Pi Zero Plus 2 (both H3 and H5
variants). As, according to the board schematics, the USB OTG port cannot
provide power to external devices, we set dr_mode to peripheral.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Link: https://lore.kernel.org/r/20200615130223.34464-1-diego.rondini@kynetics.comSigned-off-by: Maxime Ripard <maxime@cerno.tech>

Pull SafeSetID update from Micah Morton:
 "Add additional LSM hooks for SafeSetID

  SafeSetID is capable of making allow/deny decisions for set*uid calls
  on a system, and we want to add similar functionality for set*gid
  calls.

  The work to do that is not yet complete, so probably won't make it in
  for v5.8, but we are looking to get this simple patch in for v5.8
  since we have it ready.

  We are planning on the rest of the work for extending the SafeSetID
  LSM being merged during the v5.9 merge window"

* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
  security: Add LSM hooks to set*gid syscalls

The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>

Pull btrfs updates from David Sterba:
 "This reverts the direct io port to iomap infrastructure of btrfs
  merged in the first pull request. We found problems in invalidate page
  that don't seem to be fixable as regressions or without changing iomap
  code that would not affect other filesystems.

  There are four reverts in total, but three of them are followup
  cleanups needed to revert a43a67a2 cleanly. The result is the
  buffer head based implementation of direct io.

  Reverts are not great, but under current circumstances I don't see
  better options"

* tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: switch to iomap_dio_rw() for dio"
  Revert "fs: remove dio_end_io()"
  Revert "btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK"
  Revert "btrfs: split btrfs_direct_IO to read and write part"

Pull networking fixes from David Miller:

 1) Fix cfg80211 deadlock, from Johannes Berg.

 2) RXRPC fails to send norigications, from David Howells.

 3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
    Geliang Tang.

 4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.

 5) The ucc_geth driver needs __netdev_watchdog_up exported, from
    Valentin Longchamp.

 6) Fix hashtable memory leak in dccp, from Wang Hai.

 7) Fix how nexthops are marked as FDB nexthops, from David Ahern.

 8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.

 9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.

10) Fix link speed reporting in iavf driver, from Brett Creeley.

11) When a channel is used for XSK and then reused again later for XSK,
    we forget to clear out the relevant data structures in mlx5 which
    causes all kinds of problems. Fix from Maxim Mikityanskiy.

12) Fix memory leak in genetlink, from Cong Wang.

13) Disallow sockmap attachments to UDP sockets, it simply won't work.
    From Lorenz Bauer.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
  net: ethernet: ti: ale: fix allmulti for nu type ale
  net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
  net: atm: Remove the error message according to the atomic context
  bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
  libbpf: Support pre-initializing .bss global variables
  tools/bpftool: Fix skeleton codegen
  bpf: Fix memlock accounting for sock_hash
  bpf: sockmap: Don't attach programs to UDP sockets
  bpf: tcp: Recv() should return 0 when the peer socket is closed
  ibmvnic: Flush existing work items before device removal
  genetlink: clean up family attributes allocations
  net: ipa: header pad field only valid for AP->modem endpoint
  net: ipa: program upper nibbles of sequencer type
  net: ipa: fix modem LAN RX endpoint id
  net: ipa: program metadata mask differently
  ionic: add pcie_print_link_status
  rxrpc: Fix race between incoming ACK parser and retransmitter
  net/mlx5: E-Switch, Fix some error pointer dereferences
  net/mlx5: Don't fail driver on failure to create debugfs
  net/mlx5e: CT: Fix ipv6 nat header rewrite actions
  ...

This reverts commit a43a67a2.

This patch reverts the main part of switching direct io implementation
to iomap infrastructure. There's a problem in invalidate page that
couldn't be solved as regression in this development cycle.

The problem occurs when buffered and direct io are mixed, and the ranges
overlap. Although this is not recommended, filesystems implement
measures or fallbacks to make it somehow work. In this case, fallback to
buffered IO would be an option for btrfs (this already happens when
direct io is done on compressed data), but the change would be needed in
the iomap code, bringing new semantics to other filesystems.

Another problem arises when again the buffered and direct ios are mixed,
invalidation fails, then -EIO is set on the mapping and fsync will fail,
though there's no real error.

There have been discussions how to fix that, but revert seems to be the
least intrusive option.

Link: https://lore.kernel.org/linux-btrfs/20200528192103.xm45qoxqmkw7i5yl@fiona/Signed-off-by: David Sterba <dsterba@suse.com>

On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.

This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f6447 ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").

Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().

Fixes: 9d1f6447 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2020-06-12

The following pull-request contains BPF updates for your *net* tree.

We've added 26 non-merge commits during the last 10 day(s) which contain
a total of 27 files changed, 348 insertions(+), 93 deletions(-).

The main changes are:

1) sock_hash accounting fix, from Andrey.

2) libbpf fix and probe_mem sanitizing, from Andrii.

3) sock_hash fixes, from Jakub.

4) devmap_val fix, from Jesper.

5) load_bytes_relative fix, from YiFei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Looking into the context (atomic!) and the error message should be dropped.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more cifs updates from Steve French:
 "12 cifs/smb3 fixes, 2 for stable.

   - add support for idsfromsid on create and chgrp/chown allowing
     ability to save owner information more naturally for some workloads

   - improve query info (getattr) when SMB3.1.1 posix extensions are
     negotiated by using new query info level"

* tag '5.8-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add debug message for new file creation with idsfromsid mount option
  cifs: fix chown and chgrp when idsfromsid mount option enabled
  smb3: allow uid and gid owners to be set on create with idsfromsid mount option
  smb311: Add tracepoints for new compound posix query info
  smb311: add support for using info level for posix extensions query
  smb311: Add support for lookup with posix extensions query info
  smb311: Add support for SMB311 query info (non-compounded)
  SMB311: Add support for query info using posix extensions (level 100)
  smb3: add indatalen that can be a non-zero value to calculation of credit charge in smb2 ioctl
  smb3: fix typo in mount options displayed in /proc/mounts
  cifs: Add get_security_type_str function to return sec type.
  smb3: extend fscache mount volume coherency check

Let's keep "git status" happy and quiet.

Fixes: 9762dc14 ("samples: add binderfs sample program
Fixes: fca5e949 ("samples: binderfs: really compile this sample and fix build issues")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm not convinced the script makes useful automaed help lines anyway,
but since we're trying to deprecate the use of "---help---" in Kconfig
files, let's fix the doc example code too.

See commit a7f7f624 ("treewide: replace '---help---' in Kconfig
files with 'help'")

Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more Kbuild updates from Masahiro Yamada:

 - fix build rules in binderfs sample

 - fix build errors when Kbuild recurses to the top Makefile

 - covert '---help---' in Kconfig to 'help'

* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  treewide: replace '---help---' in Kconfig files with 'help'
  kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
  samples: binderfs: really compile this sample and fix build issues

Pull more SCSI updates from James Bottomley:
 "This is the set of changes collected since just before the merge
  window opened. It's mostly minor fixes in drivers.

  The one non-driver set is the three optical disk (sr) changes where
  two are error path fixes and one is a helper conversion.

  The big driver change is the hpsa compat_alloc_userspace rework by Al
  so he can kill the remaining user. This has been tested and acked by
  the maintainer"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
  scsi: acornscsi: Fix an error handling path in acornscsi_probe()
  scsi: storvsc: Remove memset before memory freeing in storvsc_suspend()
  scsi: cxlflash: Remove an unnecessary NULL check
  scsi: ibmvscsi: Don't send host info in adapter info MAD after LPM
  scsi: sr: Fix sr_probe() missing deallocate of device minor
  scsi: sr: Fix sr_probe() missing mutex_destroy
  scsi: st: Convert convert get_user_pages() --> pin_user_pages()
  scsi: target: Rename target_setup_cmd_from_cdb() to target_cmd_parse_cdb()
  scsi: target: Fix NULL pointer dereference
  scsi: target: Initialize LUN in transport_init_se_cmd()
  scsi: target: Factor out a new helper, target_cmd_init_cdb()
  scsi: hpsa: hpsa_ioctl(): Tidy up a bit
  scsi: hpsa: Get rid of compat_alloc_user_space()
  scsi: hpsa: Don't bother with vmalloc for BIG_IOCTL_Command_struct
  scsi: hpsa: Lift {BIG_,}IOCTL_Command_struct copy{in,out} into hpsa_ioctl()
  scsi: ufs: Remove redundant urgent_bkop_lvl initialization
  scsi: ufs: Don't update urgent bkops level when toggling auto bkops
  scsi: qedf: Remove redundant initialization of variable rc
  scsi: mpt3sas: Fix memset() in non-RDPQ mode
  scsi: iscsi: Fix reference count leak in iscsi_boot_create_kobj
  ...

Pull i2c updates from Wolfram Sang:
 "I2C has quite some patches for you this time. I hope it is the move to
  per-driver-maintainers which is now showing results. We will see.

  The big news is two new drivers (Nuvoton NPCM and Qualcomm CCI),
  larger refactoring of the Designware, Tegra, and PXA drivers, the
  Cadence driver supports being a slave now, and there is support to
  instanciate SPD eeproms for well-known cases (which will be
  user-visible because the i801 driver supports it), and some
  devm_platform_ioremap_resource() conversions which blow up the
  diffstat.

  Note that I applied the Nuvoton driver quite late, so some minor fixup
  patches arrived during the merge window. I chose to apply them right
  away because they were trivial"

* 'i2c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (109 commits)
  i2c: Drop stray comma in MODULE_AUTHOR statements
  i2c: npcm7xx: npcm_i2caddr[] can be static
  MAINTAINERS: npcm7xx: Add maintainer for Nuvoton NPCM BMC
  i2c: npcm7xx: Fix a couple of error codes in probe
  i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n
  i2c: npcm7xx: Remove unnecessary parentheses
  i2c: npcm7xx: Add support for slave mode for Nuvoton
  i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver
  dt-bindings: i2c: npcm7xx: add NPCM I2C controller
  i2c: pxa: don't error out if there's no pinctrl
  i2c: add 'single-master' property to generic bindings
  i2c: designware: Add Baikal-T1 System I2C support
  i2c: designware: Move reg-space remapping into a dedicated function
  i2c: designware: Retrieve quirk flags as early as possible
  i2c: designware: Convert driver to using regmap API
  i2c: designware: Discard Cherry Trail model flag
  i2c: designware: Add Baytrail sem config DW I2C platform dependency
  i2c: designware: slave: Set DW I2C core module dependency
  i2c: designware: Use `-y` to build multi-object modules
  dt-bindings: i2c: dw: Add Baikal-T1 SoC I2C controller
  ...

Pull more media updates from Mauro Carvalho Chehab:

 - a set of atomisp patches. They remove several abstraction layers, and
   fixes clang and gcc warnings (that were hidden via some macros that
   were disabling 4 or 5 types of warnings there). There are also some
   important fixes and sensor auto-detection on newer BIOSes via ACPI
   _DCM tables.

 - some fixes

* tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (95 commits)
  media: rkvdec: Fix H264 scaling list order
  media: v4l2-ctrls: Unset correct HEVC loop filter flag
  media: videobuf2-dma-contig: fix bad kfree in vb2_dma_contig_clear_max_seg_size
  media: v4l2-subdev.rst: correct information about v4l2 events
  media: s5p-mfc: Properly handle dma_parms for the allocated devices
  media: medium: cec: Make MEDIA_CEC_SUPPORT default to n if !MEDIA_SUPPORT
  media: cedrus: Implement runtime PM
  media: cedrus: Program output format during each run
  media: atomisp: improve ACPI/DMI detection logs
  media: Revert "media: atomisp: add Asus Transform T101HA ACPI vars"
  media: Revert "media: atomisp: Add some ACPI detection info"
  media: atomisp: improve sensor detection code to use _DSM table
  media: atomisp: get rid of an iomem abstraction layer
  media: atomisp: get rid of a string_support.h abstraction layer
  media: atomisp: use strscpy() instead of less secure variants
  media: atomisp: set DFS to MAX if sensor doesn't report fps
  media: atomisp: use different dfs failed messages
  media: atomisp: change the detection of ISP2401 at runtime
  media: atomisp: use macros from intel-family.h
  media: atomisp: don't set hpll_freq twice with different values
  ...

Pull libnvdimm updates from Dan Williams:
 "Small collection of cleanups to rework usage of ->queuedata and the
  GUID api"

* tag 'libnvdimm-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nvdimm/pmem: stop using ->queuedata
  nvdimm/btt: stop using ->queuedata
  nvdimm/blk: stop using ->queuedata
  libnvdimm: Replace guid_copy() with import_guid() where it makes sense

Let's keep "git status" happy and quiet.

Fixes: f5b5a164 ("Add sample notification program")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull iomap fix from Darrick Wong:
 "A single iomap bug fix for a variable type mistake on 32-bit
  architectures, fixing an integer overflow problem in the unshare
  actor"

* tag 'iomap-5.8-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: Fix unsharing of an extent >2GB on a 32-bit machine

Pull xfs fix from Darrick Wong:
 "We've settled down into the bugfix phase; this one fixes a resource
  leak on an error bailout path"

* tag 'xfs-5.8-merge-9' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: Add the missed xfs_perag_put() for xfs_ifree_cluster()

Pull 9p update from Dominique Martinet:
 "Another very quiet cycle... Only one commit: increase the size of the
  ring used for xen transport"

* tag '9p-for-5.8' of git://github.com/martinetd/linux:
  9p/xen: increase XEN_9PFS_RING_ORDER

Pull powerpc fix from Michael Ellerman:
 "One fix for a recent change which broke nested KVM guests on Power9.

  Thanks to Alexey Kardashevskiy"

* tag 'powerpc-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  KVM: PPC: Fix nested guest RC bits update

Pull ARM fixes from Russell King:

 - fix for "hex" Kconfig default to use 0x0 rather than 0 to allow these
   to be removed from defconfigs

 - fix from Ard Biesheuvel for EFI HYP mode booting

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8985/1: efi/decompressor: deal with HYP mode boot gracefully
  ARM: 8984/1: Kconfig: set default ZBOOT_ROM_TEXT/BSS value to 0x0

Pull OpenRISC update from Stafford Horne:
 "One patch found wile I was getting the glibc port ready: fix issue
  with clone TLS arg getting overwritten"

* tag 'for-linus' of git://github.com/openrisc/linux:
  openrisc: Fix issue with argument clobbering for clone/fork

Pull alpha updates from Matt Turner:
 "A few changes for alpha. They're mostly small janitorial fixes but
  there's also a build fix and most notably a patch from Mikulas that
  fixes a hang on boot on the Avanti platform, which required quite a
  bit of work and review"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
  alpha: Fix build around srm_sysrq_reboot_op
  alpha: c_next should increase position index
  alpha: Replace sg++ with sg = sg_next(sg)
  alpha: fix memory barriers so that they conform to the specification
  alpha: remove unneeded semicolon in sys_eiger.c
  alpha: remove unneeded semicolon in osf_sys.c
  alpha: Replace strncmp with str_has_prefix
  alpha: fix rtc port ranges
  alpha: Kconfig: pedantic formatting

Pull x86 RAS updates from Thomas Gleixner:
 "RAS updates from Borislav Petkov:

   - Unmap a whole guest page if an MCE is encountered in it to avoid
     follow-on MCEs leading to the guest crashing, by Tony Luck.

     This change collided with the entry changes and the merge
     resolution would have been rather unpleasant. To avoid that the
     entry branch was merged in before applying this. The resulting code
     did not change over the rebase.

   - AMD MCE error thresholding machinery cleanup and hotplug
     sanitization, by Thomas Gleixner.

   - Change the MCE notifiers to denote whether they have handled the
     error and not break the chain early by returning NOTIFY_STOP, thus
     giving the opportunity for the later handlers in the chain to see
     it. By Tony Luck.

   - Add AMD family 0x17, models 0x60-6f support, by Alexander Monakov.

   - Last but not least, the usual round of fixes and improvements"

* tag 'ras-core-2020-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
  x86/mce/dev-mcelog: Fix -Wstringop-truncation warning about strncpy()
  x86/{mce,mm}: Unmap the entire page if the whole page is affected and poisoned
  EDAC/amd64: Add AMD family 17h model 60h PCI IDs
  hwmon: (k10temp) Add AMD family 17h model 60h PCI match
  x86/amd_nb: Add AMD family 17h model 60h PCI IDs
  x86/mcelog: Add compat_ioctl for 32-bit mcelog support
  x86/mce: Drop bogus comment about mce.kflags
  x86/mce: Fixup exception only for the correct MCEs
  EDAC: Drop the EDAC report status checks
  x86/mce: Add mce=print_all option
  x86/mce: Change default MCE logger to check mce->kflags
  x86/mce: Fix all mce notifiers to update the mce->kflags bitmask
  x86/mce: Add a struct mce.kflags field
  x86/mce: Convert the CEC to use the MCE notifier
  x86/mce: Rename "first" function as "early"
  x86/mce/amd, edac: Remove report_gart_errors
  x86/mce/amd: Make threshold bank setting hotplug robust
  x86/mce/amd: Cleanup threshold device remove path
  x86/mce/amd: Straighten CPU hotplug path
  x86/mce/amd: Sanitize thresholding device creation hotplug path
  ...

Pull x86 entry updates from Thomas Gleixner:
 "The x86 entry, exception and interrupt code rework

  This all started about 6 month ago with the attempt to move the Posix
  CPU timer heavy lifting out of the timer interrupt code and just have
  lockless quick checks in that code path. Trivial 5 patches.

  This unearthed an inconsistency in the KVM handling of task work and
  the review requested to move all of this into generic code so other
  architectures can share.

  Valid request and solved with another 25 patches but those unearthed
  inconsistencies vs. RCU and instrumentation.

  Digging into this made it obvious that there are quite some
  inconsistencies vs. instrumentation in general. The int3 text poke
  handling in particular was completely unprotected and with the batched
  update of trace events even more likely to expose to endless int3
  recursion.

  In parallel the RCU implications of instrumenting fragile entry code
  came up in several discussions.

  The conclusion of the x86 maintainer team was to go all the way and
  make the protection against any form of instrumentation of fragile and
  dangerous code pathes enforcable and verifiable by tooling.

  A first batch of preparatory work hit mainline with commit
  d5f744f9 ("Pull x86 entry code updates from Thomas Gleixner")

  That (almost) full solution introduced a new code section
  '.noinstr.text' into which all code which needs to be protected from
  instrumentation of all sorts goes into. Any call into instrumentable
  code out of this section has to be annotated. objtool has support to
  validate this.

  Kprobes now excludes this section fully which also prevents BPF from
  fiddling with it and all 'noinstr' annotated functions also keep
  ftrace off. The section, kprobes and objtool changes are already
  merged.

  The major changes coming with this are:

    - Preparatory cleanups

    - Annotating of relevant functions to move them into the
      noinstr.text section or enforcing inlining by marking them
      __always_inline so the compiler cannot misplace or instrument
      them.

    - Splitting and simplifying the idtentry macro maze so that it is
      now clearly separated into simple exception entries and the more
      interesting ones which use interrupt stacks and have the paranoid
      handling vs. CR3 and GS.

    - Move quite some of the low level ASM functionality into C code:

       - enter_from and exit to user space handling. The ASM code now
         calls into C after doing the really necessary ASM handling and
         the return path goes back out without bells and whistels in
         ASM.

       - exception entry/exit got the equivivalent treatment

       - move all IRQ tracepoints from ASM to C so they can be placed as
         appropriate which is especially important for the int3
         recursion issue.

    - Consolidate the declaration and definition of entry points between
      32 and 64 bit. They share a common header and macros now.

    - Remove the extra device interrupt entry maze and just use the
      regular exception entry code.

    - All ASM entry points except NMI are now generated from the shared
      header file and the corresponding macros in the 32 and 64 bit
      entry ASM.

    - The C code entry points are consolidated as well with the help of
      DEFINE_IDTENTRY*() macros. This allows to ensure at one central
      point that all corresponding entry points share the same
      semantics. The actual function body for most entry points is in an
      instrumentable and sane state.

      There are special macros for the more sensitive entry points, e.g.
      INT3 and of course the nasty paranoid #NMI, #MCE, #DB and #DF.
      They allow to put the whole entry instrumentation and RCU handling
      into safe places instead of the previous pray that it is correct
      approach.

    - The INT3 text poke handling is now completely isolated and the
      recursion issue banned. Aside of the entry rework this required
      other isolation work, e.g. the ability to force inline bsearch.

    - Prevent #DB on fragile entry code, entry relevant memory and
      disable it on NMI, #MC entry, which allowed to get rid of the
      nested #DB IST stack shifting hackery.

    - A few other cleanups and enhancements which have been made
      possible through this and already merged changes, e.g.
      consolidating and further restricting the IDT code so the IDT
      table becomes RO after init which removes yet another popular
      attack vector

    - About 680 lines of ASM maze are gone.

  There are a few open issues:

   - An escape out of the noinstr section in the MCE handler which needs
     some more thought but under the aspect that MCE is a complete
     trainwreck by design and the propability to survive it is low, this
     was not high on the priority list.

   - Paravirtualization

     When PV is enabled then objtool complains about a bunch of indirect
     calls out of the noinstr section. There are a few straight forward
     ways to fix this, but the other issues vs. general correctness were
     more pressing than parawitz.

   - KVM

     KVM is inconsistent as well. Patches have been posted, but they
     have not yet been commented on or picked up by the KVM folks.

   - IDLE

     Pretty much the same problems can be found in the low level idle
     code especially the parts where RCU stopped watching. This was
     beyond the scope of the more obvious and exposable problems and is
     on the todo list.

  The lesson learned from this brain melting exercise to morph the
  evolved code base into something which can be validated and understood
  is that once again the violation of the most important engineering
  principle "correctness first" has caused quite a few people to spend
  valuable time on problems which could have been avoided in the first
  place. The "features first" tinkering mindset really has to stop.

  With that I want to say thanks to everyone involved in contributing to
  this effort. Special thanks go to the following people (alphabetical
  order): Alexandre Chartre, Andy Lutomirski, Borislav Petkov, Brian
  Gerst, Frederic Weisbecker, Josh Poimboeuf, Juergen Gross, Lai
  Jiangshan, Macro Elver, Paolo Bonzin,i Paul McKenney, Peter Zijlstra,
  Vitaly Kuznetsov, and Will Deacon"

* tag 'x86-entry-2020-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (142 commits)
  x86/entry: Force rcu_irq_enter() when in idle task
  x86/entry: Make NMI use IDTENTRY_RAW
  x86/entry: Treat BUG/WARN as NMI-like entries
  x86/entry: Unbreak __irqentry_text_start/end magic
  x86/entry: __always_inline CR2 for noinstr
  lockdep: __always_inline more for noinstr
  x86/entry: Re-order #DB handler to avoid *SAN instrumentation
  x86/entry: __always_inline arch_atomic_* for noinstr
  x86/entry: __always_inline irqflags for noinstr
  x86/entry: __always_inline debugreg for noinstr
  x86/idt: Consolidate idt functionality
  x86/idt: Cleanup trap_init()
  x86/idt: Use proper constants for table size
  x86/idt: Add comments about early #PF handling
  x86/idt: Mark init only functions __init
  x86/entry: Rename trace_hardirqs_off_prepare()
  x86/entry: Clarify irq_{enter,exit}_rcu()
  x86/entry: Remove DBn stacks
  x86/entry: Remove debug IDT frobbing
  x86/entry: Optimize local_db_save() for virt
  ...

Since commit 84af7a61 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.

This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.

There are a variety of indentation styles found.

  a) 4 spaces + '---help---'
  b) 7 spaces + '---help---'
  c) 8 spaces + '---help---'
  d) 1 space + 1 tab + '---help---'
  e) 1 tab + '---help---'    (correct indentation)
  f) 1 tab + 1 space + '---help---'
  g) 1 tab + 2 spaces + '---help---'

In order to convert all of them to 1 tab + 'help', I ran the
following commend:

  $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>