MGMT command is added to receive the list of blocked keys from
user-space.

The list is used to:
1) Block keys from being distributed by the device during
   the ke distribution phase of SMP.
2) Filter out any keys that were previously saved so
   they are no longer used.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds a unified API qca_power_on() to support both wcn399x and
Rome power on. For wcn399x it calls the qca_wcn3990_init() to init the
regulators, and for Rome it pulls up the bt_en GPIO to power up the btsoc.
It also moves all the power up operation from hdev->open() to
hdev->setup().
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patches fixes two warnings of checkpatch.pl, both of the type
WARNING: Missing a blank line after declarations
Signed-off-by: Changqi Du <d.changqi@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/bluetooth/hci_qca.c: In function 'qca_controller_memdump':
drivers/bluetooth/hci_qca.c:980:6: warning:
 variable 'opcode' set but not used [-Wunused-but-set-variable]

It is never used since commit d841502c ("Bluetooth: hci_qca: Collect
controller memory dump during SSR"), so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Use vfree() instead of kfree() to free vmalloc()
allocated data.

Fixes: d841502c ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Variable icid is being rc is assigned with a value that is never
read. The assignment is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

USB "VendorID:04ca ProductID:3021" is a new QCA ROME USB
Bluetooth device, this patch will support firmware downloading for it.

T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3021 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This enables the code to set the input MTU using the underline link
packet types when set to 0, previously this would likely be rejected by
the remote peer since it would be bellow the minimal of 48 for BR/EDR
or 23 for LE, that way it shall be safe to use 0 without causing any
side effects.

This is convenient for the likes of A2DP transport, see:

https://habr.com/en/post/456182/Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This handles LE PHY Update Complete event and store both tx_phy and
rx_phy into hci_conn.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We will collect the ramdump of BT controller when hardware error event
received before rebooting the HCI layer. Before restarting a subsystem
or a process running on a subsystem, it is often required to request
either a subsystem or a process to perform proper cache dump and
software failure reason into a memory buffer which application
processor can retrieve afterwards. SW developers can often provide
initial investigation by looking into that debugging information.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The commit 3347a809 ("Bluetooth: hci_bcm: Fix RTS handling during
startup") is causing at least a regression for AP6256 on Orange Pi 3.
So do the RTS line handing during startup only on the necessary platform.

Fixes: 3347a809 ("Bluetooth: hci_bcm: Fix RTS handling during startup")
Reported-by: Ondřej Jirman <megous@megous.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This fixes a double definition error when CONFIG_BT_BCM is not set.

Fixes: 52837990 ("Bluetooth: btbcm: Support pcm configuration")
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Replace of_device_get_match_data with device_get_match_data to make driver
work across platforms.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The BCM4329 is a 802.11 a/b/g/n WiFi + Bluetooth 2.1 chip which is found
in Azurewave AW-NH611 WiFi+BT module.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Driver supports BCM4329, but there is no device-tree compatible for
that chip. Let's add it in order to allow boards to specify Bluetooth
in theirs device-trees, in particular this is useful for NVIDIA Tegra20
boards.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The macro is really not needed and can be replaced with either usage of
bt_err_ratelimited or bt_dev_err_ratelimited.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The macro will be used to display rate limited warning messages in the
log.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function
‘bfa_ioc_fwver_clear’:
drivers/net/ethernet/brocade/bna/bfa_ioc.c:1127:13: warning: variable
‘pgoff’ set but not used [-Wunused-but-set-variable]

It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current driver only exists on a non NUMA aware machine.
With 44768dec ("page_pool: handle page recycle for NUMA_NO_NODE condition")
applied we can safely change that to NUMA_NO_NODE and accommodate future
NUMA aware hardware using netsec network interface
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Passing NULL to l2tp_pernet causes a crash via BUG_ON.
Dereferencing net in net_generic() also has the same effect.
This patch removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Passing NULL to phonet_pernet causes a crash via BUG_ON.
Dereferencing net in net_generic() also has the same effect.
This patch removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The argument is always ignored, so remove it.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

net/ethtool/linkmodes.c: In function 'ethnl_set_linkmodes':
net/ethtool/linkmodes.c:326:32: warning:
 variable 'lsettings' set but not used [-Wunused-but-set-variable]
  struct ethtool_link_settings *lsettings;
                                ^
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

REXMIT_NEW is a macro for "FRTO-style
transmit of unsent/new packets", this patch
makes it more readable.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ENETC implement time specific departure capability, which enables
the user to specify when a frame can be transmitted. When this
capability is enabled, the device will delay the transmission of
the frame so that it can be transmitted at the precisely specified time.
The delay departure time up to 0.5 seconds in the future. If the
departure time in the transmit BD has not yet been reached, based
on the current time, the packet will not be transmitted.

This driver was loaded by Qos driver ETF. User could load it by tc
commands. Here are the example commands:

tc qdisc add dev eth0 root handle 1: mqprio \
	   num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 etf \
	   clockid CLOCK_TAI delta 30000  offload

These example try to set queue mapping first and then set queue 7
with 30us ahead dequeue time.

Then user send test frame should set SO_TXTIME feature for socket.

There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation
are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure
operation are mutually exclusive.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use resource_size rather than a verbose computation on
the end and start fields.

The semantic patch that makes these changes is as follows:
(http://coccinelle.lip6.fr/)

<smpl>
@@ struct resource ptr; @@
- (ptr.end + 1 - ptr.start)
+ resource_size(&ptr)

@@ struct resource *ptr; @@
- (ptr->end + 1 - ptr->start)
+ resource_size(ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The idtcm_caps structure is only copied into another structure,
so make it const.

The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only the SFC4000 code, now moved to sfc-falcon, needed I2C.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
tcp: Add support for L3 domains to MD5 auth

With VRF, the scope of network addresses is limited to the L3 domain
the device is associated. MD5 keys are based on addresses, so proper
VRF support requires an L3 domain to be considered for the lookups.

Leverage the new TCP_MD5SIG_EXT option to add support for a device index
to MD5 keys. The __tcpm_pad entry in tcp_md5sig is renamed to tcpm_ifindex
and a new flag, TCP_MD5SIG_FLAG_IFINDEX, in tcpm_flags determines if the
entry is examined. This follows what was done for MD5 and prefixes with
commits
   8917a777 ("tcp: md5: add TCP_MD5SIG_EXT socket option to set a key address prefix")
   6797318e ("tcp: md5: add an address prefix for key lookup")

Handling both a device AND L3 domain is much more complicated for the
response paths. This set focuses only on L3 support - requiring the
device index to be an l3mdev (ie, VRF). Support for slave devices can
be added later if desired, much like the progression of support for
sockets bound to a VRF and then bound to a device in a VRF. Kernel
code is setup to explicitly call out that current lookup is for an L3
index, while the uapi just references a device index allowing its
meaning to include other devices in the future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add tests for new TCP MD5 API for L3 domains (VRF).

A new namespace is added to create a duplicate configuration between
the VRF and default VRF to verify overlapping config is handled properly.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add tests for existing TCP MD5 APIs - both single address
config and the new extended API for prefixes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update nettest to implement TCP_MD5SIG_EXT for a prefix and a device.

Add a new option, -m, to specify a prefix and length to use with MD5
auth. The device option comes from the existing -d option. If either
are set and MD5 auth is requested, TCP_MD5SIG_EXT is used instead of
TCP_MD5SIG.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On failure to set MD5 password, do_server should return 1 so that the
program exits with 1 rather than 255. This used for negative testing
when adding MD5 with device option.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for userspace to specify a device index to limit the scope
of an entry via the TCP_MD5SIG_EXT setsockopt. The existing __tcpm_pad
is renamed to tcpm_ifindex and the new field is only checked if the new
TCP_MD5SIG_FLAG_IFINDEX is set in tcpm_flags. For now, the device index
must point to an L3 master device (e.g., VRF). The API and error
handling are setup to allow the constraint to be relaxed in the future
to any device index.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add l3index to tcp_md5sig_key to represent the L3 domain of a key, and
add l3index to tcp_md5_do_add and tcp_md5_do_del to fill in the key.

With the key now based on an l3index, add the new parameter to the
lookup functions and consider the l3index when looking for a match.

The l3index comes from the skb when processing ingress packets leveraging
the helpers created for socket lookups, tcp_v4_sdif and inet_iif (and the
v6 variants). When the sdif index is set it means the packet ingressed a
device that is part of an L3 domain and inet_iif points to the VRF device.
For egress, the L3 domain is determined from the socket binding and
sk_bound_dev_if.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v4_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v6_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract the typecast to (union tcp_md5_addr *) to a local variable
rather than the current long, inline declaration with function calls.

No functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed Coding function and style issues
Signed-off-by: Niu Xilei <niu_xilei@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Allow setting default port priority

Petr says:

When LLDP APP TLV selector 1 (EtherType) is used with PID of 0, the
corresponding entry specifies "default application priority [...] when
application priority is not otherwise specified."

mlxsw currently supports this type of APP entry, but uses it only as a
fallback for unspecified DSCP rules. However non-IP traffic is prioritized
according to port-default priority, not according to the DSCP-to-prio
tables, and thus it's currently not possible to prioritize such traffic
correctly.

This patchset extends the use of the abovementioned APP entry to also set
default port priority (in patches #1 and #2) and then (in patch #3) adds a
selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>