When do suspend/resume stress test, some log shows "rcv is not +last".
The issue is that enet suspend will disable phy clock, phy link down,
after resume back, enet MAC redo initial and ready to tx/rx packet,
but phy still is not ready which is doing auto-negotiation. When phy
link is not up, don't schdule napi soft irq.

[Peter]
It has fixed kernel panic after long time suspend/resume test
with nfs rootfs.

[ 8864.429458] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.434799] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.440088] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.445424] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.450782] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.456111] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 8864.464225] pgd = 80004000
[ 8864.466997] [00000000] *pgd=00000000
[ 8864.470627] Internal error: Oops: 17 [#1] SMP ARM
[ 8864.475353] Modules linked in: evbug
[ 8864.479006] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.0.0-rc1-00044-g7a2a1d2 #234
[ 8864.486854] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[ 8864.492709] task: be069380 ti: be07a000 task.ti: be07a000
[ 8864.498137] PC is at memcpy+0x80/0x330
[ 8864.501919] LR is at gro_pull_from_frag0+0x34/0xa8
[ 8864.506735] pc : [<802bb080>]    lr : [<8057c204>]    psr: 00000113
[ 8864.506735] sp : be07bbd4  ip : 00000010  fp : be07bc0c
[ 8864.518235] r10: 0000000e  r9 : 00000000  r8 : 809c7754
[ 8864.523479] r7 : 809c7754  r6 : bb43c040  r5 : bd280cc0  r4 : 00000012
[ 8864.530025] r3 : 00000804  r2 : fffffff2  r1 : 00000000  r0 : bb43b83c
[ 8864.536575] Flags: nzcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[ 8864.543904] Control: 10c5387d  Table: bd14c04a  DAC: 00000015
[ 8864.549669] Process ksoftirqd/0 (pid: 3, stack limit = 0xbe07a210)
[ 8864.555869] Stack: (0xbe07bbd4 to 0xbe07c000)
[ 8864.560250] bbc0:                                              bd280cc0 bb43c040 809c7754
[ 8864.568455] bbe0: 809c7754 bb43b83c 00000012 8057c204 00000000 bd280cc0 bd8a0718 00000003
[ 8864.576658] bc00: be07bc5c be07bc10 8057ebf0 8057c1dc 00000000 00000000 8057ecc4 bef59760
[ 8864.584863] bc20: 00000002 bd8a0000 be07bc64 809c7754 00000000 bd8a0718 bd280cc0 bd8a0000
[ 8864.593066] bc40: 00000000 0000001c 00000000 bd8a0000 be07bc74 be07bc60 8057f148 8057eb90
[ 8864.601268] bc60: bf0810a0 00000000 be07bcf4 be07bc78 8044e7b4 8057f12c 00000000 8007df6c
[ 8864.609470] bc80: bd8a0718 00000040 00000000 bd280a80 00000002 00000019 bd8a0600 bd8a1214
[ 8864.617672] bca0: bd8a0690 bf0810a0 00000000 00000000 bd8a1000 00000000 00000027 bd280cc0
[ 8864.625874] bcc0: 80062708 800625cc 000943db bd8a0718 00000001 000d1166 00000040 be7c1ec0
[ 8864.634077] bce0: 0000012c be07bd00 be07bd3c be07bcf8 8057fc98 8044e3ac 809c2ec0 3ddff000
[ 8864.642280] bd00: be07bd00 be07bd00 be07bd08 be07bd08 00000000 00000020 809c608c 00000003
[ 8864.650481] bd20: 809c6080 40000001 809c6088 00200100 be07bd84 be07bd40 8002e690 8057fac8
[ 8864.658684] bd40: be07bd64 be07bd50 00000001 04208040 000d1165 0000000a be07bd84 809c0d7c
[ 8864.666885] bd60: 00000000 809c6af8 00000000 00000001 be008000 00000000 be07bd9c be07bd88
[ 8864.675087] bd80: 8002eb64 8002e564 00000125 809c0d7c be07bdc4 be07bda0 8006f100 8002eaac
[ 8864.683291] bda0: c080e10c be07bde8 809c6c6c c080e100 00000002 00000000 be07bde4 be07bdc8
[ 8864.691492] bdc0: 800087a0 8006f098 806f2934 20000013 ffffffff be07be1c be07be44 be07bde8
[ 8864.699695] bde0: 800133a4 80008784 00000001 00000001 00000000 00000000 be7c1680 00000000
[ 8864.707896] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30
[ 8864.716098] be20: 8006278c 806f2934 20000013 ffffffff be069380 be7c1680 be07be7c be07be48
[ 8864.724300] be40: 80049cfc 806f2910 00000001 00000000 80049cb4 00000000 be07be7c be7c1680
[ 8864.732502] be60: be3289c0 be069380 bd23b600 be0cfe00 be07bebc be07be80 806ed614 80049c68
[ 8864.740706] be80: be07a000 0000020a 809c608c 00000003 00000001 8002e858 be07a000 be035740
[ 8864.748907] bea0: 00000000 00000001 809d4598 00000000 be07bed4 be07bec0 806edd0c 806ed440
[ 8864.757110] bec0: be07a000 be07a000 be07bee4 be07bed8 806edd68 806edcf0 be07bef4 be07bee8
[ 8864.765311] bee0: 8002e860 806edd34 be07bf24 be07bef8 800494b0 8002e828 be069380 00000000
[ 8864.773512] bf00: be035780 be035740 8004938c 00000000 00000000 00000000 be07bfac be07bf28
[ 8864.781715] bf20: 80045928 80049398 be07bf44 00000001 00000000 be035740 00000000 00030003
[ 8864.789917] bf40: dead4ead ffffffff ffffffff 80a2716c 80b59b00 00000000 8088c954 be07bf5c
[ 8864.798120] bf60: be07bf5c 00000000 00000000 dead4ead ffffffff ffffffff 80a2716c 00000000
[ 8864.806320] bf80: 00000000 8088c954 be07bf88 be07bf88 be035780 8004584c 00000000 00000000
[ 8864.814523] bfa0: 00000000 be07bfb0 8000ed10 80045858 00000000 00000000 00000000 00000000
[ 8864.822723] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 8864.830925] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 5ffbb5f7 f9fcf5e7
[ 8864.839115] Backtrace:
[ 8864.841631] [<8057c1d0>] (gro_pull_from_frag0) from [<8057ebf0>] (dev_gro_receive+0x6c/0x3f8)
[ 8864.850173]  r6:00000003 r5:bd8a0718 r4:bd280cc0 r3:00000000
[ 8864.855958] [<8057eb84>] (dev_gro_receive) from [<8057f148>] (napi_gro_receive+0x28/0xac)
[ 8864.864152]  r10:bd8a0000 r9:00000000 r8:0000001c r7:00000000 r6:bd8a0000 r5:bd280cc0
[ 8864.872115]  r4:bd8a0718
[ 8864.874713] [<8057f120>] (napi_gro_receive) from [<8044e7b4>] (fec_enet_rx_napi+0x414/0xc74)
[ 8864.883167]  r5:00000000 r4:bf0810a0
[ 8864.886823] [<8044e3a0>] (fec_enet_rx_napi) from [<8057fc98>] (net_rx_action+0x1dc/0x2ec)
[ 8864.895016]  r10:be07bd00 r9:0000012c r8:be7c1ec0 r7:00000040 r6:000d1166 r5:00000001
[ 8864.902982]  r4:bd8a0718
[ 8864.905570] [<8057fabc>] (net_rx_action) from [<8002e690>] (__do_softirq+0x138/0x2c4)
[ 8864.913417]  r10:00200100 r9:809c6088 r8:40000001 r7:809c6080 r6:00000003 r5:809c608c
[ 8864.921382]  r4:00000020
[ 8864.923966] [<8002e558>] (__do_softirq) from [<8002eb64>] (irq_exit+0xc4/0x138)
[ 8864.931289]  r10:00000000 r9:be008000 r8:00000001 r7:00000000 r6:809c6af8 r5:00000000
[ 8864.939252]  r4:809c0d7c
[ 8864.941841] [<8002eaa0>] (irq_exit) from [<8006f100>] (__handle_domain_irq+0x74/0xe8)
[ 8864.949688]  r4:809c0d7c r3:00000125
[ 8864.953342] [<8006f08c>] (__handle_domain_irq) from [<800087a0>] (gic_handle_irq+0x28/0x68)
[ 8864.961707]  r9:00000000 r8:00000002 r7:c080e100 r6:809c6c6c r5:be07bde8 r4:c080e10c
[ 8864.969597] [<80008778>] (gic_handle_irq) from [<800133a4>] (__irq_svc+0x44/0x5c)
[ 8864.977097] Exception stack(0xbe07bde8 to 0xbe07be30)
[ 8864.982173] bde0:                   00000001 00000001 00000000 00000000 be7c1680 00000000
[ 8864.990377] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30
[ 8864.998573] be20: 8006278c 806f2934 20000013 ffffffff
[ 8865.003638]  r7:be07be1c r6:ffffffff r5:20000013 r4:806f2934
[ 8865.009447] [<806f2904>] (_raw_spin_unlock_irq) from [<80049cfc>] (finish_task_switch+0xa0/0x160)
[ 8865.018334]  r4:be7c1680 r3:be069380
[ 8865.021993] [<80049c5c>] (finish_task_switch) from [<806ed614>] (__schedule+0x1e0/0x5dc)
[ 8865.030098]  r8:be0cfe00 r7:bd23b600 r6:be069380 r5:be3289c0 r4:be7c1680
[ 8865.036942] [<806ed434>] (__schedule) from [<806edd0c>] (preempt_schedule_common+0x28/0x44)
[ 8865.045307]  r9:00000000 r8:809d4598 r7:00000001 r6:00000000 r5:be035740 r4:be07a000
[ 8865.053197] [<806edce4>] (preempt_schedule_common) from [<806edd68>] (_cond_resched+0x40/0x48)
[ 8865.061822]  r4:be07a000 r3:be07a000
[ 8865.065472] [<806edd28>] (_cond_resched) from [<8002e860>] (run_ksoftirqd+0x44/0x64)
[ 8865.073252] [<8002e81c>] (run_ksoftirqd) from [<800494b0>] (smpboot_thread_fn+0x124/0x190)
[ 8865.081550] [<8004938c>] (smpboot_thread_fn) from [<80045928>] (kthread+0xdc/0xf8)
[ 8865.089133]  r10:00000000 r9:00000000 r8:00000000 r7:8004938c r6:be035740 r5:be035780
[ 8865.097097]  r4:00000000 r3:be069380
[ 8865.100752] [<8004584c>] (kthread) from [<8000ed10>] (ret_from_fork+0x14/0x24)
[ 8865.107990]  r7:00000000 r6:00000000 r5:8004584c r4:be035780
[ 8865.113767] Code: e320f000 e4913004 e4914004 e4915004 (e4916004)
[ 8865.120006] ---[ end trace b0a4c6bd499288ca ]---
[ 8865.124697] Kernel panic - not syncing: Fatal exception in interrupt
[ 8865.131084] ---[ end Kernel panic - not syncing: Fatal exception in interrupt

Cc: [v3.19+] stable@vger.kernel.org
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Iyappan Subramanian says:

====================
drivers: net: xgene: Fix backward compatibility of newer firmware with older kernel

Kernel 3.17 driver supports only RGMII ethernet interface.
Since the Tianocore DT contains same compatibility string for RGMII,
SGMII based 1G and XFI based 10G interfaces, crash happens when probe called
on SGMII based 1G and XFI based 10G interface.

This patch fixes the backward compatibility of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.

v2: Address comments from v1
* updated cover letter subject line with net: xgene
* Documentation: formatted compatible string values as list

v1:
* Initial version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the backward compatibile of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the backward compatibility of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.

The new bindings are in sync with the newer firmware.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. For an IPv4 ping socket, ping_check_bind_addr does not check
   the family of the socket address that's passed in. Instead,
   make it behave like inet_bind, which enforces either that the
   address family is AF_INET, or that the family is AF_UNSPEC and
   the address is 0.0.0.0.
2. For an IPv6 ping socket, ping_check_bind_addr returns EINVAL
   if the socket family is not AF_INET6. Return EAFNOSUPPORT
   instead, for consistency with inet6_bind.
3. Make ping_v4_sendmsg and ping_v6_sendmsg return EAFNOSUPPORT
   instead of EINVAL if an incorrect socket address structure is
   passed in.
4. Make IPv6 ping sockets be IPv6-only. The code does not support
   IPv4, and it cannot easily be made to support IPv4 because
   the protocol numbers for ICMP and ICMPv6 are different. This
   makes connect(::ffff:192.0.2.1) fail with EAFNOSUPPORT instead
   of making the socket unusable.

Among other things, this fixes an oops that can be triggered by:

    int s = socket(AF_INET, SOCK_DGRAM, IPPROTO_ICMP);
    struct sockaddr_in6 sin6 = {
        .sin6_family = AF_INET6,
        .sin6_addr = in6addr_any,
    };
    bind(s, (struct sockaddr *) &sin6, sizeof(sin6));

Change-Id: If06ca86d9f1e4593c0d6df174caca3487c57a241
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.

Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we're getting IRQs after lots of resources are already
allocated:
 * netdev
 * clocks
 * MDIO bus
Also HW gets initialized by the time when checking IRQs as well.

Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.

But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.

For example this is what happens for me:
 --->8---
 stmmaceth e0018000.ethernet: no reset control found
 stmmac - user ID: 0x10, Synopsys ID: 0x37
  Ring mode enabled
  DMA HW capability register supported
  Normal descriptors
  RX Checksum Offload Engine supported (type 2)
  TX Checksum insertion supported
  Enable RX Mitigation via HW Watchdog Timer
 libphy: stmmac: probed
 eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
 platform e0018000.ethernet: Driver stmmaceth requests probe deferral
 ...
 ...
 ...
 stmmaceth e0018000.ethernet: no reset control found
 stmmac - user ID: 0x10, Synopsys ID: 0x37
  Ring mode enabled
  DMA HW capability register supported
  Normal descriptors
  RX Checksum Offload Engine supported (type 2)
  TX Checksum insertion supported
  Enable RX Mitigation via HW Watchdog Timer
 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
 sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
 CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
 Workqueue: deferwq deferred_probe_work_func

 Stack Trace:
  arc_unwind_core+0xb8/0x114
  warn_slowpath_common+0x5a/0x8c
  warn_slowpath_fmt+0x2e/0x38
  sysfs_warn_dup+0x4e/0x68
  sysfs_create_dir_ns+0x98/0xa0
  kobject_add_internal+0x8c/0x2e8
  kobject_add+0x4a/0x8c
  device_add+0xc6/0x448
  mdiobus_register+0x6c/0x164
  stmmac_mdio_register+0x112/0x264
  stmmac_dvr_probe+0x6c0/0x85c
  stmmac_pltfr_probe+0x2e4/0x50c
  platform_drv_probe+0x26/0x5c
  really_probe+0x76/0x1dc
  bus_for_each_drv+0x42/0x7c
  device_attach+0x64/0x6c
  bus_probe_device+0x74/0xa4
  deferred_probe_work_func+0x50/0x84
  process_one_work+0xf8/0x2cc
  worker_thread+0x110/0x478
  kthread+0x8a/0x9c
  ret_from_fork+0x14/0x18
 ---[ end trace a2dfaa7d630c8be1 ]---
 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
 kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
 CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G        W
4.0.0-rc1-next-20150303+ #8
 Workqueue: deferwq deferred_probe_work_func

 Stack Trace:
  arc_unwind_core+0xb8/0x114
  warn_slowpath_common+0x5a/0x8c
  warn_slowpath_fmt+0x2e/0x38
  kobject_add_internal+0x218/0x2e8
  kobject_add+0x4a/0x8c
  device_add+0xc6/0x448
  mdiobus_register+0x6c/0x164
  stmmac_mdio_register+0x112/0x264
  stmmac_dvr_probe+0x6c0/0x85c
  stmmac_pltfr_probe+0x2e4/0x50c
  platform_drv_probe+0x26/0x5c
  really_probe+0x76/0x1dc
  bus_for_each_drv+0x42/0x7c
  device_attach+0x64/0x6c
  bus_probe_device+0x74/0xa4
  deferred_probe_work_func+0x50/0x84
  process_one_work+0xf8/0x2cc
  worker_thread+0x110/0x478
  kthread+0x8a/0x9c
  ret_from_fork+0x14/0x18
 ---[ end trace a2dfaa7d630c8be2 ]---
 libphy: mii_bus stmmac-0 failed to register
 : Cannot register as MDIO bus
 stmmac_pltfr_probe: main driver probe failed
 stmmaceth: probe of e0018000.ethernet failed with error -22
 --->8---

Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull dma-buf fixes from Sumit Semwal:
 "Minor timeout & other fixes on reservation/fence"

* tag 'dma-buf-for-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
  reservation: Remove shadowing local variable 'ret'
  dma-buf/fence: don't wait when specified timeout is zero
  reservation: wait only with non-zero timeout specified (v3)

Pull KVM fixes from Marcelo Tosatti:
 "KVM bug fixes, including a SVM interrupt injection regression fix,
  MIPS and ARM bug fixes"

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: MIPS: Enable after disabling interrupt
  KVM: MIPS: Fix trace event to save PC directly
  KVM: SVM: fix interrupt injection (apic->isr_count always 0)
  KVM: emulate: fix CMPXCHG8B on 32-bit hosts
  KVM: VMX: fix build without CONFIG_SMP
  arm/arm64: KVM: Add exit reaons to kvm_exit event tracing
  ARM: KVM: Fix size check in __coherent_cache_guest_page

Pull ARC fixes from Vineet Gupta:
 - Fix for /proc/<pid>/maps "stack" vma annotation
 - sched stats not printing correct sleeping task PC
 - perf not reporting page faults

* tag 'arc-4.0-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: Fix thread_saved_pc()
  ARC: Fix KSTK_ESP()
  ARC: perf: Enable generic software events
  ARC: Make arc_unwind_core accessible externally

Pull powerpc fixes from Michael Ellerman:
 - Fix for dynticks.
 - Fix for smpboot bug.
 - Fix for IOMMU group refcounting.

* tag 'powerpc-4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/iommu: Remove IOMMU device references via bus notifier
  powerpc/smp: Wait until secondaries are active & online
  powerpc: Re-enable dynticks

After d905c5df ("PPC: POWERNV: move iommu_add_device earlier"), the
refcnt on the kobject backing the IOMMU group for a PCI device is
elevated by each call to pci_dma_dev_setup_pSeriesLP() (via
set_iommu_table_base_and_group). When we go to dlpar a multi-function
PCI device out:

        iommu_reconfig_notifier ->
                iommu_free_table ->
                        iommu_group_put
                        BUG_ON(tbl->it_group)

We trip this BUG_ON, because there are still references on the table, so
it is not freed. Fix this by moving the powernv bus notifier to common
code and calling it for both powernv and pseries.

Fixes: d905c5df ("PPC: POWERNV: move iommu_add_device earlier")
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Anton has a busy ppc64le KVM box where guests sometimes hit the infamous
"kernel BUG at kernel/smpboot.c:134!" issue during boot:

  BUG_ON(td->cpu != smp_processor_id());

Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops
output confirms it:

  CPU: 0
  Comm: watchdog/130

The problem is that we aren't ensuring the CPU active bit is set for the
secondary before allowing the master to continue on. The master unparks
the secondary CPU's kthreads and the scheduler looks for a CPU to run
on. It calls select_task_rq() and realises the suggested CPU is not in
the cpus_allowed mask. It then ends up in select_fallback_rq(), and
since the active bit isnt't set we choose some other CPU to run on.

This seems to have been introduced by 6acbfb96 "sched: Fix hotplug
vs. set_cpus_allowed_ptr()", which changed from setting active before
online to setting active after online. However that was in turn fixing a
bug where other code assumed an active CPU was also online, so we can't
just revert that fix.

The simplest fix is just to spin waiting for both active & online to be
set. We already have a barrier prior to set_cpu_online() (which also
sets active), to ensure all other setup is completed before online &
active are set.

Fixes: 6acbfb96 ("sched: Fix hotplug vs. set_cpus_allowed_ptr()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull nfsd fixes from Bruce Fields:
 "Three miscellaneous bugfixes, most importantly the clp->cl_revoked
  bug, which we've seen several reports of people hitting"

* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
  sunrpc: integer underflow in rsc_parse()
  nfsd: fix clp->cl_revoked list deletion causing softlock in nfsd
  svcrpc: fix memory leak in gssp_accept_sec_context_upcall

Pull networking fixes from David Miller:

 1) If an IPVS tunnel is created with a mixed-family destination
    address, it cannot be removed.  Fix from Alexey Andriyanov.

 2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
    Neira Ayuso.

 3) Generic statistics infrastructure can reference variables sitting on
    a released function stack, therefore use dynamic allocation always.
    Fix from Ignacy Gawędzki.

 4) skb_copy_bits() return value test is inverted in ip_check_defrag().

 5) Fix network namespace exit in openvswitch, we have to release all of
    the per-net vports.  From Pravin B Shelar.

 6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.

 7) Fix rhashtable grow/shrink behavior, only expand during inserts and
    shrink during deletes.  From Daniel Borkmann.

 8) Netdevice names with semicolons should never be allowed, because
    they serve as a separator.  From Matthew Thode.

 9) Use {,__}set_current_state() where appropriate, from Fabian
    Frederick.

10) Revert byte queue limits support in r8169 driver, it's causing
    regressions we can't figure out.

11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
    measure packets in flight, properly use tcp_packets_in_flight()
    instead.  From Neal Cardwell.

12) Fix accidental removal of support for bluetooth in CSR based Intel
    wireless cards.  From Marcel Holtmann.

13) We accidently added a behavioral change between native and compat
    tasks, wrt testing the MSG_CMSG_COMPAT bit.  Just ignore it if the
    user happened to set it in a native binary as that was always the
    behavior we had.  From Catalin Marinas.

14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
    handling, from Bob Copeland.

15) Fix stale ->radar_required setting in mac80211 that can prevent
    starting new scans, from Eliad Peller.

16) Fix memory leak in nl80211 monitor, from Johannes Berg.

17) Fix race in TX index handling in xen-netback, from David Vrabel.

18) Don't enable interrupts in amx-xgbe driver until all software et al.
    state is ready for the interrupt handler to run.  From Thomas
    Lendacky.

19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
    W Biederman.

20) The amount of header space needed in macvtap was not calculated
    properly, fix it otherwise we splat past the beginning of the
    packet.  From Eric Dumazet.

21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.

22) Don't raw initialize or mod timers, use setup_timer() and
    mod_timer() instead.  From Vaishali Thakkar.

23) Fix software maintained statistics in bcmgenet and systemport
    drivers, from Florian Fainelli.

24) DMA descriptor updates in sh_eth need proper memory barriers, from
    Ben Hutchings.

25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
    Kubecek.

26) Openvswitch's non-masked set actions aren't constructed properly
    into netlink messages, fix from Joe Stringer.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
  openvswitch: Fix serialization of non-masked set actions.
  gianfar: Reduce logging noise seen due to phy polling if link is down
  ibmveth: Add function to enable live MAC address changes
  net: bridge: add compile-time assert for cb struct size
  udp: only allow UFO for packets from SOCK_DGRAM sockets
  sh_eth: Really fix padding of short frames on TX
  Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
  sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
  sh_eth: Ensure proper ordering of descriptor active bit write/read
  net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
  net/mlx4_core: Fix wrong mask and error flow for the update-qp command
  net: systemport: fix software maintained statistics
  net: bcmgenet: fix software maintained statistics
  rxrpc: don't multiply with HZ twice
  rxrpc: terminate retrans loop when sending of skb fails
  net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
  net: pasemi: Use setup_timer and mod_timer
  net: stmmac: Use setup_timer and mod_timer
  net: 8390: axnet_cs: Use setup_timer and mod_timer
  net: 8390: pcnet_cs: Use setup_timer and mod_timer
  ...

Set actions consist of a regular OVS_KEY_ATTR_* attribute nested inside
of a OVS_ACTION_ATTR_SET action attribute. When converting masked actions
back to regular set actions, the inner attribute length was not changed,
ie, double the length being serialized. This patch fixes the bug.

Fixes: 83d2b9ba ("net: openvswitch: Support masked set actions.")
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 6ce29b0e ("gianfar: Avoid unnecessary reg accesses in adjust_link()")
eliminates unnecessary calls to adjust_link for phy devices which don't support
interrupts and need polling. As part of that work, the 'new_state' local flag,
which was used to reduce logging noise on the console, was eliminated.

Unfortunately, that means that a 'Link is Down' log message will now be
issued continuously if a link is configured as UP, the link state is down,
and the associated phy requires polling. This occurs because priv->oldduplex
is -1 in this case, which always differs from phydev->duplex. In addition,
phydev->speed may also differ from priv->oldspeed.  gfar_update_link_state()
is therefore called each time a phy is polled, even if the link state did not
change.

Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a function that will enable changing the MAC address
of an ibmveth interface while it is still running.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

make build fail if structure no longer fits into ->cb storage.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a tricky story of the new atomic state handling and the legacy
code fighting over each another. The bug at hand is an underrun of the
framebuffer reference with subsequent hilarity caused by the load
detect code. Which is peculiar since the the exact same code works
fine as the implementation of the legacy setcrtc ioctl.

Let's look at the ingredients:

- Currently our code is a crazy mix of legacy modeset interfaces to
  set the parameters and half-baked atomic state tracking underneath.
  While this transition is going we're using the transitional plane
  helpers to update the atomic side (drm_plane_helper_disable/update
  and friends), i.e. plane->state->fb. Since the state structure owns
  the fb those functions take care of that themselves.

  The legacy state (specifically crtc->primary->fb) is still managed
  by the old code (and mostly by the drm core), with the fb reference
  counting done by callers (core drm for the ioctl or the i915 load
  detect code). The relevant commit is

  commit ea2c67bb
  Author: Matt Roper <matthew.d.roper@intel.com>
  Date:   Tue Dec 23 10:41:52 2014 -0800

      drm/i915: Move to atomic plane helpers (v9)

- drm_plane_helper_disable has special code to handle multiple calls
  in a row - it checks plane->crtc == NULL and bails out. This is to
  match the proper atomic implementation which needs the crtc to get
  at the implied locking context atomic updates always need. See

  commit acf24a39
  Author: Daniel Vetter <daniel.vetter@ffwll.ch>
  Date:   Tue Jul 29 15:33:05 2014 +0200

      drm/plane-helper: transitional atomic plane helpers

- The universal plane code split out the implicit primary plane from
  the CRTC into it's own full-blown drm_plane object. As part of that
  the setcrtc ioctl (which updated both the crtc mode and primary
  plane) learned to set crtc->primary->crtc on modeset to make sure
  the plane->crtc assignments statate up to date in

  commit e13161af
  Author: Matt Roper <matthew.d.roper@intel.com>
  Date:   Tue Apr 1 15:22:38 2014 -0700

      drm: Add drm_crtc_init_with_planes() (v2)

  Unfortunately we've forgotten to update the load detect code. Which
  wasn't a problem since the load detect modeset is temporary and
  always undone before we drop the locks.

- Finally there is a organically grown history (i.e. don't ask) around
  who sets the legacy plane->fb for the various driver entry points.
  Originally updating that was the drivers duty, but for almost all
  places we've moved that (plus updating the refcounts) into the core.
  Again the exception is the load detect code.

Taking all together the following happens:
- The load detect code doesn't set crtc->primary->crtc. This is only
  really an issue on crtcs never before used or when userspace
  explicitly disabled the primary plane.

- The plane helper glue code short-circuits because of that and leaves
  a non-NULL fb behind in plane->state->fb and plane->fb. The state
  fb isn't a real problem (it's properly refcounted on its own), it's
  just the canary.

- Load detect code drops the reference for that fb, but doesn't set
  plane->fb = NULL. This is ok since it's still living in that old
  world where drivers had to clear the pointer but the core/callers
  handled the refcounting.

- On the next modeset the drm core notices plane->fb and takes care of
  refcounting it properly by doing another unref. This drops the
  refcount to zero, leaving state->plane now pointing at freed memory.

- intel_plane_duplicate_state still assume it owns a reference to that
  very state->fb and bad things start to happen.

Fix this all by applying the same duct-tape as for the legacy setcrtc
ioctl code and set crtc->primary->crtc properly.

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a
UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to
CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer
checksum is to be computed on segmentation. However, in this case,
skb->csum_start and skb->csum_offset are never set as raw socket
transmit path bypasses udp_send_skb() where they are usually set. As a
result, driver may access invalid memory when trying to calculate the
checksum and store the result (as observed in virtio_net driver).

Moreover, the very idea of modifying the userspace provided UDP header
is IMHO against raw socket semantics (I wasn't able to find a document
clearly stating this or the opposite, though). And while allowing
CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit
too intrusive change just to handle a corner case like this. Therefore
disallowing UFO for packets from SOCK_DGRAM seems to be the best option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
Fixes for sh_eth #4 v2

I'm continuing review and testing of Ethernet support on the R-Car H2
chip, with help from a colleague.  This series fixes a few more issues.

These are not tested on any of the other supported chips.

v2: Add note that the revert is not a pure revert.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding.  That isn't the case; we need to use skb_put_padto() instead.

(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2.  We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)
Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit fd9af07c.

The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16.  I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).

Also adjust a comment to agree with this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor.  This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips.  This will result in unpredictable behaviour on those chips
after an RDE.

Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips.  This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.

Fixes: 79fba9f5 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.

Add memory barriers to ensure that this ordering is maintained.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable disabled interrupt, on unsuccessful operation.

Found by Coccinelle.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>

Currently the guest exit trace event saves the VCPU pointer to the
structure, and the guest PC is retrieved by dereferencing it when the
event is printed rather than directly from the trace record. This isn't
safe as the printing may occur long afterwards, after the PC has changed
and potentially after the VCPU has been freed. Usually this results in
the same (wrong) PC being printed for multiple trace events. It also
isn't portable as userland has no way to access the VCPU data structure
when interpreting the trace record itself.

Lets save the actual PC in the structure so that the correct value is
accessible later.

Fixes: 669e846e ("KVM/MIPS32: MIPS arch specific APIs for KVM")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # v3.10+
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>

Pull GPIO fixes from Linus Walleij:
 "Two GPIO fixes:

   - Fix a translation problem in of_get_named_gpiod_flags()

   - Fix a long standing container_of() mistake in the TPS65912 driver"

* tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: tps65912: fix wrong container_of arguments
  gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node

Merge branch 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal

Pull thermal management fixes from Eduardo Valentin:
 "Specifics:

   - Several fixes in tmon tool.

   - Fixes in intel int340x for _ART and _TRT tables.

   - Add id for Avoton SoC into powerclamp driver.

   - Fixes in RCAR thermal driver to remove race conditions and fix fail
     path

   - Fixes in TI thermal driver: removal of unnecessary code and build
     fix if !CONFIG_PM_SLEEP

   - Cleanups in exynos thermal driver

   - Add stubs for include/linux/thermal.h.  Now drivers using thermal
     calls but that also work without CONFIG_THERMAL will be able to
     compile for systems that don't care about thermal.

  Note: I am sending this pull on Rui's behalf while he fixes issues in
  his Linux box"

* 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: int340x_thermal: Ignore missing _ART, _TRT tables
  thermal/intel_powerclamp: add id for Avoton SoC
  tools/thermal: tmon: silence 'set but not used' warnings
  tools/thermal: tmon: use pkg-config to determine library dependencies
  tools/thermal: tmon: support cross-compiling
  tools/thermal: tmon: add .gitignore
  tools/thermal: tmon: fixup tui windowing calculations
  tools/thermal: tmon: tui: don't hard-code dialog window size assumptions
  tools/thermal: tmon: add min/max macros
  tools/thermal: tmon: add --target-temp parameter
  thermal: exynos: Clean-up code to use oneline entry for exynos compatible table
  thermal: rcar: Make error and remove paths symmetrical with init
  thermal: rcar: Fix race condition between init and interrupt
  thermal: Introduce dummy functions when thermal is not defined
  ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister"
  thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP

In commit b4eef9b3, we started to use hwapic_isr_update() != NULL
instead of kvm_apic_vid_enabled(vcpu->kvm).  This didn't work because
SVM had it defined and "apicv" path in apic_{set,clear}_isr() does not
change apic->isr_count, because it should always be 1.  The initial
value of apic->isr_count was based on kvm_apic_vid_enabled(vcpu->kvm),
which is always 0 for SVM, so KVM could have injected interrupts when it
shouldn't.

Fix it by implicitly setting SVM's hwapic_isr_update to NULL and make the
initial isr_count depend on hwapic_isr_update() for good measure.

Fixes: b4eef9b3 ("kvm: x86: vmx: NULL out hwapic_isr_update() in case of !enable_apicv")
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>

Pull md fixes from Neil Brown:
 "Three md fixes:

   - fix a read-balance problem that was reported 2 years ago, but that
     I never noticed the report :-(

   - fix for rare RAID6 problem causing incorrect bitmap updates when
     two devices fail.

   - add __ATTR_PREALLOC annotation now that it is possible"

* tag 'md/4.0-fixes' of git://neil.brown.name/md:
  md: mark some attributes as pre-alloc
  raid5: check faulty flag for array status during recovery.
  md/raid1: fix read balance when a drive is write-mostly.

Pull arch/metag fix from James Hogan:
 "This is just a single patch to fix the KSTK_EIP() and KSTK_ESP()
  macros for metag which have always been erronously returning the PC
  and stack pointer of the task's kernel context rather than from its
  user context saved at entry from userland into the kernel, which
  affects the contents of /proc/<pid>/maps and /proc/<pid>/stat"

* tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
  metag: Fix KSTK_EIP() and KSTK_ESP() macros

Or Gerlitz says:

====================
Mellanox driver fixes

Two small fixes, please apply to net.

Both patches should go to 3.19.y too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Packets which are sent from the selftest (ethtool) flow,
should not be passed to GRO stack but rather dropped by
the driver after validation. To achieve that, we disable
GRO for the duration of the selftest.

Fixes: dd65beac ("net/mlx4_en: Extend usage of napi_gro_frags")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS)
of the update-qp command was defined twice (using enum value and pre-processor
define directive) and wrong.

The return value of the call to mlx4_update_qp() from within the SRIOV
resource-tracker was wrongly voided down.

Fix both issues.

issue: none
Fixes: 09e05c3f ('net/mlx4: Set vlan stripping policy by the right command')
Fixes: ce8d9e0d ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fixes from Ingo Molnar:
 "A CR4-shadow 32-bit init fix, plus two typo fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Init per-cpu shadow copy of CR4 on 32-bit CPUs too
  x86/platform/intel-mid: Fix trivial printk message typo in intel_mid_arch_setup()
  x86/cpu/intel: Fix trivial typo in intel_tlb_table[]

Pull timer fixes from Ingo Molnar:
 "Three clockevents/clocksource driver fixes"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: pxa: Fix section mismatch
  clocksource: mtk: Fix race conditions in probe code
  clockevents: asm9260: Fix compilation error with sparc/sparc64 allyesconfig