Instead of struct clk, as this should be only used by providers.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

As it's only used internally, in drivers/clk/clk.c.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

As __clk_release could call kfree on clk and then we wouldn't have a safe way
of getting the module that owns the clock.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Fixes: fcb0ee6a ("clk: Implement clk_unregister")
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Merge tag 'ib-mfd-regulator-clk-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into clk-next

Immutable branch between MFD, Regulator and Clk, due for v3.19

Merge tag 'v3.19-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next

- clock phase setting capability for the rk3288 mmc clocks
- pll init to allow syncing to actual rate table values
- some more exported clocks
- fixes for some clocks (typos etc) all of them not yet used
  in actual drivers

This patch adds the 2 physical clocks for the mmc (drive and sample). They're
mostly there for the phase properties, but they also show the true clock
(by dividing by RK3288_MMC_CLKGEN_DIV).

The drive and sample phases are generated by dividing an upstream parent clock
by 2, this allows us to adjust the phase by 90 deg.

There's also an option to have up to 255 delay elements (40-80 picoseconds long).
This driver uses those elements (under the assumption that they're 60 ps long)
to generate approximate 22.5 degrees options. 67.5 (22.5*3) might be as high as
90 deg if the delay elements are as big as 80 ps, so a finer division (smaller
than 22.5) was not picked because the phase might not be monotonic anymore.
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

These clocks represent the physical clocks (including phases) and they will
later be used for clock phase tuning.
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This exposes the clock that comes out of the i2s block which generally
goes to the audio codec.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
[removed CLK_SET_RATE_PARENT from original patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The DMC clocks need to be turned off at runtime.  Use the newly
assigned clock IDs to export them.
Signed-off-by: Jeff Chen <cym@rock-chips.com>
[dianders: split into two patches; adjusted commit msg]
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The DMC clocks need to be turned off at runtime, so we should have IDs
so we can export them.
Signed-off-by: Jeff Chen <cym@rock-chips.com>
[dianders: split into two patches; adjusted commit msg]
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

drivers/clk/clk-s2mps11.c:181:2-3: Unneeded semicolon

 Removes unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

CC: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

This patch adds the binding documentation for Samsung S2MPS13 PMIC
which is similiar with existing S2MPS14 PMIC. S2MPS13 has the different number
of regulators from S2MPS14 and RTC/Clock is the same with the S2MPS14.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds the support for S2MPS13 PMIC clock which is same with existing
S2MPS14 RTC IP. But, S2MPS13 uses all of clocks (32khz_{ap|bt|cp}).
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds the support for Samsung S2MPS13 PMIC device to the sec-core MFD
driver. The S2MPS13 is very similar with existing S2MPS14 and includes PMIC/
RTC/CLOCK devices.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the new flag to gpll and cpll on rk3188 and similar and to
gpll, cpll and npll on rk3288.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>

In some cases firmware brings up plls with different parameters than the ones
noted in the rate table for the specific frequency. These firmware-selected
parameters are worse than the tested ones in the pll rate tables but cannot
be changed by a simple clk_set_rate call when the rate stays the same.

Therefore add a ROCKCHIP_PLL_SYNC_RATE flag and implement an init callback
that checks the runtime-parameters against the matching rate table entry
and adjusts them to the table-ones if necessary.

If no rate table is set or the current rate does not match any rate-table
entry no changes are made.

Being able to limit this adjustment to specific plls is necessary to not
touch the ones supplying core components like the apll and dpll supplying
the armcores and dram.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>

In some cases we might need to access the data of the pll mux before the actual
mux gets registered - like in the following patch adding an init-callback.

Therefore populate pll_mux before registering the core pll-clock.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>

This adds a flag parameter to plls that allows us to create
special flags to tweak the behaviour of the plls if necessary.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>

Merge tag 'sunxi-clocks-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next

Allwinner Clocks additions for 3.19

A few patches that should go through the clock tree, mostly fixes, cleanups,
and new clocks additions to start to support the A80.

A CLK_MUX_INDEX_BIT mux has one bit per parent, but the sun7i-a20-gmac-clk
has 2 bits selecting between 3 possible parents using values of 0, 1, 2,
which makes it a regular mux which should not have CLK_MUX_INDEX_BIT set in
its flag.

However we do not support parent 1 (an external clock), so use a table to
select parent 0 or 2, which are the 2 parents we support.

Note this has not been causing any issues sofar, because we start with a
parent setting of parent 0, and only ever re-parent to parent 2 (for which
we use an index of 1 as we skip parent 1) and with CLK_MUX_INDEX_BIT set
we write a value of 2 for index 1.

Tested on both a cubietruck (which uses rgmii mode) as well as a cs908
(an a31s board which uses mii mode).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some clock modules on the A31 use PLL6x2 as one of their inputs.
This patch changes the PLL6 implementation for A31 to a divs clock,
i.e. clock with multiple outputs that have different dividers.
The first output will be the normal PLL6 output, and the second
will be PLL6x2.

This patch fixes the PLL6 N factor in the clock driver, and removes
any /2 dividers in the PLL6 factors clock part. The N factor counts
from 1 to 32, mapping to values 0 to 31, as shown in the A31 manual.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Currently sunxi_divs_clk_setup assumes the number of child clocks
to be the same as the number of clock-output-names, and a maximum
of SUNXI_DIVS_MAX_QTY child clocks.

On sun6i, PLL6 only has 1 child clock, but the parent would be used
as well, thereby also having it's own clock-output-names entry. This
results in an extra bogus clock being registered.

This patch adds an entry for the number of child clocks alongside
the data structures for them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This driver does not match the hardware, which is actually compatible
to sun4i-a10-apb1-clk. Since we've switch to the correct one, drop
this driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The apb2 clocks are actually the same as apb1 clocks on the other sunxi
platforms, hence compatible with "allwinner,sun4i-a10-apb1-clk".

Update the dtsi to use the new unified apb1 clk.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

With the new factors infrastructure in place, we can unify apb1 and
apb1_mux as a single clock now.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
[wens@csie.org: Change apb1 node label to "apb1"; reword commit title]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The USB HSIC PHY clock divider is set in the register RK2928_CLKSEL_CON(11).
Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

In rk3188 clock branches, spdif_pre gate was set to RK2928_CLKGATE_CON(13) bit 13.
This appears to be a copy-paste error because such a register does not exist.
We correct it to RK2928_CLKGATE_CON(0) and find out that the rk3188 spdif clock
is the same as the rk3066 spdif clock, so we move it to the common clock branches.
Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Use __initconst instead of __initdata for constant init data.
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

If CLK_MUX_INDEX_BIT is set, then each bit turns on / off a single parent,
so theoretically multiple parents could be enabled at the same time, but in
practice only one bit should ever be 1. So to select parent 0, set
the register (*) to 0x01, to select parent 1 set it 0x02, parent 2, 0x04,
parent 3, 0x08, etc.

But the current code does:

                if (mux->flags & CLK_MUX_INDEX_BIT)
                        index = (1 << ffs(index));

Which means that:

For an input index of 0, ffs returns 0, so we set the register
to 0x01, ok.

For an input index of 1, ffs returns 1, so we set the register
to 0x02, ok.

For an input index of 2, ffs returns 2, so we set the register
to 0x04, ok.

For an input index of 3, ffs returns 1, so we set the register
to 0x02, not good!

The code should simply be:

                if (mux->flags & CLK_MUX_INDEX_BIT)
                        index = 1 << index;

Which always does the right thing, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Commit 8e33f91a ("clk: shmobile: clk-mstp: change to using
clock-indices") forgot to replace all occurrences of
"renesas,clock-indices" in the driver-specific binding documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

It's the same to the next statement, "ret = clk->parent". I think compiler will
optimize it, it's just not looking well.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

Merge tag 'v3.19-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next-rockchip

- fixes for clock ordering/rate issues
- do not keep all clocks enabled anymore
- allow special pll rates for special cases

The parent clock for hclk_lcdc1 was set to aclk_cpu instead of hclk_cpu.
Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Have each pxa variant (pxa25x, pxa27x, pxa3xx) have its own device-tree
clock initializing function, to be able to register its own specific
core clocks.

Apply that change specifically to pxa27x.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

As the clock descriptions are constant and only usefull at init time,
mark them as such by :
 - spliting clock description (desc) and clock private data (dynamic)
 - mark __initdata clock descriptions

This makes all the register and descriptions of the clocks to go after
kernel init phase.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>