spmi_regulator_set_voltage_time_sel() calculates the amount of delay
needed as the result of setting a new voltage.  Essentially this is the
absolute difference of the old and new voltages, divided by the slew rate.

The implementation of spmi_regulator_set_voltage_time_sel() is wrong.

It attempts to calculate the difference in voltages by using the
difference in selectors and multiplying by the voltage step between
selectors.  This ignores the possibility that the old and new selectors
might be from different ranges, which have different step values.  Also,
the difference between the selectors may encapsulate N ranges inbetween,
so a summation of each selector change from old to new would be needed.

Lets avoid all of that complexity, and just get the actual voltage
represented by both the old and new selector, and use those to directly
compute the voltage delta.  This is more straight forward, and has the
side benifit of avoiding issues with regulator implementations that don't
have hardware register support to get the current configured range.

Fixes: e92a4047 ("regulator: Add QCOM SPMI regulator driver")
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reported-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to the DA9061 and DA9062 datasheets the LDO voltage selection
registers have a lower value of 0x02. This applies to voltage registers
VLDO1_A, VLDO2_A, VLDO3_A and VLDO4_A. This linear offset of 0x02 was
previously not observed by the driver, causing the LDO output voltage to
be systematically lower by two steps (= 0.1V).

This patch fixes the minimum linear selector offset by setting it to a
value of 2 and increases the n_voltages by the same amount allowing
voltages in the range 0x02 -> 0.9V to 0x38 -> 3.6V to be correctly
selected. Also fixes an incorrect calculaton for the n_voltages value in
the regulator LDO2.

These fixes effect all LDO regulators for DA9061 and DA9062.
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Felix Riemann <felix.riemann@sma.de>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The PMS405 has 5 HFSMPS and 13 LDO regulators,

This commit adds support for one of the 5 HFSMPS regulators (s3) to
the spmi regulator driver.

The PMIC HFSMPS 430 regulators have 8 mV step size and a voltage
control scheme consisting of two  8-bit registers defining a 16-bit
voltage set point in units of millivolts

S3 controls the cpu voltages (s3 is a buck regulator of type HFS430);
it is therefore required so we can enable voltage scaling for safely
running cpufreq.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The PMS405 supports 5 SMPS and 13 LDO regulators.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The pm8005_s1 is VDD_GFX, and needs to be on to enable the GPU.
This should be hooked up to the GPU CPR, but we don't have support for that
yet, so until then, just turn on the regulator and keep it on so that we
can focus on basic GPU bringup.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The PM8005 is used on the msm8998 MTP.  The S1 regulator is VDD_GFX, ie
it needs to be on and controlled inorder to use the GPU.  Add support to
drive the PM8005 regulators so that we can bring up the GPU on msm8998.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Document the dt bindings for the PM8005 regulators which are usually used
for VDD of standalone blocks on a SoC like the GPU.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Makes things look more consistent.
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 5.2-rc4

spmi_regulator_common_get_mode and spmi_regulator_common_set_mode use
multi-level ifs which mirror a switch statement.  Refactor to use a switch
statement to make the code flow more clear.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This finalizes the descriptor conversion of the MAX8952 driver
by letting the VID0 and VID1 GPIOs be fetched from descriptors.

Both VID0 and VID1 must be supplied for the VID selection to work,
I add some code to preserve the semantics that if only one of
the two VID gpios is supplied, it will be initialized to low.
This might be a bit overzealous, but I want to preserve any
implicit semantics.

This is currently only used by device tree in-kernel but it is
still also possible to supply the same GPIOs using a machine
descriptor table if a board file is used.

Ideally this should be phased over to using gpio-regulator.c
that does the same thing, but it might require some refactoring
and needs testing on real hardware.

Cc: Tomasz Figa <tfiga@chromium.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

When building with CONFIG_MFD_88PM800 and CONFIG_REGULATOR_88PM800
enabled as loadable modules, we see the following warning:

warning: same module names found:
  drivers/regulator/88pm800.ko
  drivers/mfd/88pm800.ko

Rework so that the file is named 88pm800-regulator.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This converts the Wolfson Micro WM831x DCDC converter to use
a GPIO descriptor for the GPIO driving the DVS pin.

There is just one (non-DT) machine in the kernel using this, and
that is the Wolfson Micro (now Cirrus) Cragganmore 6410 so we
patch this board to pass a descriptor table and fix up the driver
accordingly.

Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: patches@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This driver does not use any symbols from <linux/gpio.h>
no <linux/gpio/consumer.h> so just drop the includes.

Cc: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pull ceph fixes from Ilya Dryomov:
 "A change to call iput() asynchronously to avoid a possible deadlock
  when iput_final() needs to wait for in-flight I/O (e.g. readahead) and
  a fixup for a cleanup that went into -rc1"

* tag 'ceph-for-5.2-rc4' of git://github.com/ceph/ceph-client:
  ceph: fix error handling in ceph_get_caps()
  ceph: avoid iput_final() while holding mutex or in dispatch thread
  ceph: single workqueue for inode related works

Pull xen fix from Juergen Gross:
 "Just one fix for the Xen block frontend driver avoiding allocations
  with order > 0"

* tag 'for-linus-5.2b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen-blkfront: switch kcalloc to kvcalloc for large array allocation

Pull s390 fixes from Heiko Carstens:

 - fix stack unwinder: the stack unwinder rework has on off-by-one bug
   which prevents following stack backchains over more than one context
   (e.g. irq -> process).

 - fix address space detection in exception handler: if user space
   switches to access register mode, which is not supported anymore, the
   exception handler may resolve to the wrong address space.

* tag 's390-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/unwind: correct stack switching during unwind
  s390/mm: fix address space detection in exception handling

Pull MIPS fixes from Paul Burton:

 - Declare ginvt() __always_inline due to its use of an argument as an
   inline asm immediate.

 - A VDSO build fix following Kbuild changes made this cycle.

 - A fix for boot failures on txx9 systems following memory
   initialization changes made this cycle.

 - Bounds check virt_addr_valid() to prevent it spuriously indicating
   that bogus addresses are valid, in turn fixing hardened usercopy
   failures that have been present since v4.12.

 - Build uImage.gz for pistachio systems by default, since this is the
   image we need in order to actually boot on a board.

 - Remove an unused variable in our uprobes code.

* tag 'mips_fixes_5.2_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: uprobes: remove set but not used variable 'epc'
  MIPS: pistachio: Build uImage.gz by default
  MIPS: Make virt_addr_valid() return bool
  MIPS: Bounds check virt_addr_valid
  MIPS: TXx9: Fix boot crash in free_initmem()
  MIPS: remove a space after -I to cope with header search paths for VDSO
  MIPS: mark ginvt() as __always_inline

Pull yet more SPDX updates from Greg KH:
 "Another round of SPDX header file fixes for 5.2-rc4

  These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
  added, based on the text in the files. We are slowly chipping away at
  the 700+ different ways people tried to write the license text. All of
  these were reviewed on the spdx mailing list by a number of different
  people.

  We now have over 60% of the kernel files covered with SPDX tags:
	$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
	Files checked:            64533
	Files with SPDX:          40392
	Files with errors:            0

  I think the majority of the "easy" fixups are now done, it's now the
  start of the longer-tail of crazy variants to wade through"

* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.2-rc4 to resolve
  a number of reported issues.

  The most "notable" one here is the kernel headers in proc^Wsysfs
  fixes. Those changes move the header file info into sysfs and fixes
  the build issues that you reported.

  Other than that, a bunch of small habanalabs driver fixes, some fpga
  driver fixes, and a few other tiny driver fixes.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  habanalabs: Read upper bits of trace buffer from RWPHI
  habanalabs: Fix virtual address access via debugfs for 2MB pages
  fpga: zynqmp-fpga: Correctly handle error pointer
  habanalabs: fix bug in checking huge page optimization
  habanalabs: Avoid using a non-initialized MMU cache mutex
  habanalabs: fix debugfs code
  uapi/habanalabs: add opcode for enable/disable device debug mode
  habanalabs: halt debug engines on user process close
  test_firmware: Use correct snprintf() limit
  genwqe: Prevent an integer overflow in the ioctl
  parport: Fix mem leak in parport_register_dev_model
  fpga: dfl: expand minor range when registering chrdev region
  fpga: dfl: Add lockdep classes for pdata->lock
  fpga: dfl: afu: Pass the correct device to dma_mapping_error()
  fpga: stratix10-soc: fix use-after-free on s10_init()
  w1: ds2408: Fix typo after 49695ac4 (reset on output_write retry with readback)
  kheaders: Do not regenerate archive if config is not changed
  kheaders: Move from proc to sysfs
  lkdtm/bugs: Adjust recursion test to avoid elision
  lkdtm/usercopy: Moves the KERNEL_DS test to non-canonical

Pull i2c fixes from Wolfram Sang:
 "I2C has a driver bugfix and a MAINTAINERS fix"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: Karthikeyan Ramasubramanian is MIA
  i2c: xiic: Add max_read_len quirk

Pull dmaengine fixes from Vinod Koul:

 - jz4780 transfer fix for acking descriptors early

 - fsl-qdma: clean registers on error

 - dw-axi-dmac: null pointer dereference fix

 - mediatek-cqdma: fix sleeping in atomic context

 - tegra210-adma: fix bunch os issues like crashing in driver probe,
   channel FIFO configuration etc.

 - sprd: Fixes for possible crash on descriptor status, block length
   overflow. For 2-stage transfer fix incorrect start, configuration and
   interrupt handling.

* tag 'dmaengine-fix-5.2-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: sprd: Add interrupt support for 2-stage transfer
  dmaengine: sprd: Fix the right place to configure 2-stage transfer
  dmaengine: sprd: Fix block length overflow
  dmaengine: sprd: Fix the incorrect start for 2-stage destination channels
  dmaengine: sprd: Add validation of current descriptor in irq handler
  dmaengine: sprd: Fix the possible crash when getting descriptor status
  dmaengine: tegra210-adma: Fix spelling
  dmaengine: tegra210-adma: Fix channel FIFO configuration
  dmaengine: tegra210-adma: Fix crash during probe
  dmaengine: mediatek-cqdma: sleeping in atomic context
  dmaengine: dw-axi-dmac: fix null dereference when pointer first is null
  dmaengine: fsl-qdma: Add improvement
  dmaengine: jz4780: Fix transfers being ACKed too soon

Pull block fixes from Jens Axboe:

 - Allow symlink from the bfq.weight cgroup parameter to the general
   weight (Angelo)

 - Damien is new skd maintainer (Bart)

 - NVMe pull request from Sagi, with a few small fixes.

 - Ensure we set DMA segment size properly, dma-debug is now tripping on
   these (Christoph)

 - Remove useless debugfs_create() return check (Greg)

 - Remove redundant unlikely() check on IS_ERR() (Kefeng)

 - Fixup request freeing on exit (Ming)

* tag 'for-linus-20190608' of git://git.kernel.dk/linux-block:
  block, bfq: add weight symlink to the bfq.weight cgroup parameter
  cgroup: let a symlink too be created with a cftype file
  block: free sched's request pool in blk_cleanup_queue
  nvme-rdma: use dynamic dma mapping per command
  nvme: Fix u32 overflow in the number of namespace list calculation
  mmc: also set max_segment_size in the device
  mtip32xx: also set max_segment_size in the device
  rsxx: don't call dma_set_max_seg_size
  nvme-pci: don't limit DMA segement size
  block: Drop unlikely before IS_ERR(_OR_NULL)
  block: aoe: no need to check return value of debugfs_create functions
  nvmet: fix data_len to 0 for bdev-backed write_zeroes
  MAINTAINERS: Hand over skd maintainership
  nvme-tcp: fix queue mapping when queue count is limited
  nvme-rdma: fix queue mapping when queue count is limited

Pull SCSI fixes from James Bottomley:
 "Two bug fixes, both for fairly serious problems; the UFS one looks
  like it could be used to exfiltrate data from the kernel, although
  probably only a privileged user has access to the command management
  interface and the missing unlock in smartpqi is long standing and
  probably a little used error path"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: smartpqi: unlock on error in pqi_submit_raid_request_synchronous()
  scsi: ufs: Check that space was properly alloced in copy_query_response

Merge tag 'linux-kselftest-5.2-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fix from Shuah Khan:
 "This consists of a single fix for a vm test build failure regression
  when it is built by itself"

* tag 'linux-kselftest-5.2-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: vm: Fix test build failure when built by itself

Pull drm fixes from Dave Airlie:
 "A small bit more lively this week but not majorly so. I'm away in
  Japan next week for family holiday, so I'll be pretty disconnected,
  I've asked Daniel to do fixes for the week while I'm out.

  The nouveau firmware changes are a bit large, but they address a big
  problem where a whole set of boards don't load with the driver, and
  the new firmware fixes that, so I think it's worth trying to land it
  now.

  core:
   - Allow fb changes in async commits (drivers as well)

  udmabuf:
   - Unmap scatterlist when unmapping udmabuf

  nouveau:
   - firmware loading fixes for secboot firmware on new GPU revision.

  komeda:
   - oops, dma mapping and warning fixes

  arm-hdlcd:
   - clock fixes
   - mode validation fix

  i915:
   - Add a missing Icelake workaround
   - GVT - DMA map fault fix and enforcement fixes

  amdgpu:
   - DCE resume fix
   - New raven variation updates"

* tag 'drm-fixes-2019-06-07-1' of git://anongit.freedesktop.org/drm/drm: (33 commits)
  drm/nouveau/secboot/gp10[2467]: support newer FW to fix SEC2 failures on some boards
  drm/nouveau/secboot: enable loading of versioned LS PMU/SEC2 ACR msgqueue FW
  drm/nouveau/secboot: split out FW version-specific LS function pointers
  drm/nouveau/secboot: pass max supported FW version to LS load funcs
  drm/nouveau/core: support versioned firmware loading
  drm/nouveau/core: pass subdev into nvkm_firmware_get, rather than device
  drm/komeda: Potential error pointer dereference
  drm/komeda: remove set but not used variable 'kcrtc'
  drm/amd/amdgpu: add RLC firmware to support raven1 refresh
  drm/amd/powerplay: add set_power_profile_mode for raven1_refresh
  drm/amdgpu: fix ring test failure issue during s3 in vce 3.0 (V2)
  udmabuf: actually unmap the scatterlist
  drm/arm/hdlcd: Allow a bit of clock tolerance
  drm/arm/hdlcd: Actually validate CRTC modes
  drm/arm/mali-dp: Add a loop around the second set CVAL and try 5 times
  drm/komeda: fixing of DMA mapping sg segment warning
  drm: don't block fb changes for async plane updates
  drm/vc4: fix fb references in async update
  drm/msm: fix fb references in async update
  drm/amd: fix fb references in async update
  ...

A mail just bounced back with "user unknown":

550 5.1.1 <kramasub@codeaurora.org> User doesn't exist

I also couldn't find a more recent address in git history. So, remove
this stale entry.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This driver does not support reading more than 255 bytes at once because
the register for storing the number of bytes to read is only 8 bits. Add
a max_read_len quirk to enforce this.

This was found when using this driver with the SFP driver, which was
previously reading all 256 bytes in the SFP EEPROM in one transaction.
This caused a bunch of hard-to-debug errors in the xiic driver since the
driver/logic was treating the number of bytes to read as zero.
Rejecting transactions that aren't supported at least allows the problem
to be diagnosed more easily.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Merge tag 'hwmon-for-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Fix a couple of inconsistencies and locking problems in pmbus driver

 - Register with thermal subsystem only on systems supporting devicetree

* tag 'hwmon-for-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (pmbus/core) Treat parameters as paged if on multiple pages
  hwmon: (pmbus/core) mutex_lock write in pmbus_set_samples
  hwmon: (core) add thermal sensors only if dev->of_node is present

The lockref cmpxchg loop is unbound as long as the spinlock is not
taken. Depending on the hardware implementation of compare-and-swap
a high number of loop retries might happen.

Add an upper bound to the loop to force the fallback to spinlocks
after some time. A retry value of 100 should not impact any hardware
that does not have this issue.

With the retry limit the performance of an open-close testcase
improved between 60-70% on ThunderX2.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jan Glauber <jglauber@marvell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Architectures that support memory tagging have a need to perform untagging
(stripping the tag) in various parts of the kernel. This patch adds an
untagged_addr() macro, which is defined as noop for architectures that do
not support memory tagging. The oncoming patch series will define it at
least for sparc64 and arm64.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull xtensa fix from Max Filippov:
 "Fix a section mismatch between memblock_reserve and mem_reserve.

  This fixes tinyconfig xtensa builds"

* tag 'xtensa-20190607' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: Fix section mismatch between memblock_reserve and mem_reserve

Pull NVMe fixes from Sagi.

* 'nvme-5.2-rc-next' of git://git.infradead.org/nvme:
  nvme-rdma: use dynamic dma mapping per command
  nvme: Fix u32 overflow in the number of namespace list calculation
  nvmet: fix data_len to 0 for bdev-backed write_zeroes
  nvme-tcp: fix queue mapping when queue count is limited
  nvme-rdma: fix queue mapping when queue count is limited

Merge tag 'kbuild-fixes-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull more Kbuild fixes from Masahiro Yamada:

 - fix kselftest-merge to find config fragments in deeper directories

 - fix kconfig unit test, which was broken by SPDX tag addition

 - add + prefix to buildtar to suppress jobserver unavailable warning

 - fix checkstack.pl to recognize arch=arm64

 - suppress noisy warning from cc-cross-prefix

* tag 'kbuild-fixes-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: use more portable 'command -v' for cc-cross-prefix
  scripts/checkstack.pl: Fix arm64 wrong or unknown architecture
  kbuild: tar-pkg: enable communication with jobserver
  kconfig: tests: fix recursive inclusion unit test
  kbuild: teach kselftest-merge to find nested config files

Pull MMC fixes from Ulf Hansson:
 "Here's a couple of MMC and MEMSTICK fixes:

  MMC host:
   - sdhci: Fix SDIO IRQ thread deadlock
   - sdhci-tegra: Fix a warning message
   - sdhci_am654: Fix SLOTTYPE write
   - meson-gx: Fix IRQ ack
   - tmio: Fix SCC error handling to avoid false positive CRC error

  MEMSTICK core:
   - mspro_block: Fix returning a correct error code"

* tag 'mmc-v5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci_am654: Fix SLOTTYPE write
  mmc: sdhci: Fix SDIO IRQ thread deadlock
  mmc: meson-gx: fix irq ack
  mmc: tmio: fix SCC error handling to avoid false positive CRC error
  mmc: tegra: Fix a warning message
  memstick: mspro_block: Fix an error code in mspro_block_issue_req()

Pull power management fixes from Rafael Wysocki:
 "These fix a crash during resume from hibernation introduced during the
  4.19 cycle, cause the new Performance and Energy Bias Hint (EPB) code
  to be built only if CONFIG_PM is set and add a few missing kerneldoc
  comments.

  Specifics:

   - Fix a crash that occurs when a kernel with 'nosmt' in the command
     line is used to resume the system from hibernation (as the
     "restore" kernel), because memory mapping differences between the
     restore and image kernels cause SMT siblings to be woken up from
     idle states and subsequently they try to fetch instructions from
     incorrect memory locations (Jiri Kosina).

   - Cause the new Performance and Energy Bias Hint (EPB) code to be
     built only if CONFIG_PM is set, because that code is not really
     necessary otherwise (Rafael Wysocki).

   - Add kerneldoc comments to documents some helper functions related
     to system-wide suspend to avoid possible confusion regarding their
     purpose (Rafael Wysocki)"

* tag 'pm-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  x86/power: Fix 'nosmt' vs hibernation triple fault during resume
  PM: sleep: Add kerneldoc comments to some functions
  x86: intel_epb: Do not build when CONFIG_PM is unset

get_desc() computes a pointer into the LDT while holding a lock that
protects the LDT from being freed, but then drops the lock and returns the
(now potentially dangling) pointer to its caller.

Fix it by giving the caller a copy of the LDT entry instead.

Fixes: 670f928b ("x86/insn-eval: Add utility function to get segment descriptor")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>