'mtd_get_device_size()' returns the size of the whole MTD device, that is the
mtd_info master size. This will be used by UBI to calculate the maximum number
of bad blocks (MBB) on a MTD device.

Artem: amended the patch a bit.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

'struct mtd_info' is not modified by 'mtd_is_partition()' so it can be marked
as "const".
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_MTD_UBI_BEB_RESERVE has been removed and now we use
CONFIG_MTD_UBI_BEB_LIMIT instead.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

CONFIG_MTD_UBI_BEB_RESERVE and MIN_RESEVED_PEBS are no longer used,
since the amount of reserved eraseblocks for bad PEB handling is now
derived from 'ubi->bad_peb_limit' (ubi's maximum expected bad
eraseblocks).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>

The existing mechanism of reserving PEBs for bad PEB handling has two
flaws:
- It is calculated as a percentage of good PEBs instead of total PEBs.
- There's no limit on the amount of PEBs UBI reserves for future bad
  eraseblock handling.

This patch changes the mechanism to overcome these flaws.

The desired level of PEBs reserved for bad PEB handling (beb_rsvd_level)
is set to the maximum expected bad eraseblocks (bad_peb_limit) minus the
existing number of bad eraseblocks (bad_peb_count).

The actual amount of PEBs reserved for bad PEB handling is usually set
to the desired level (but in some circumstances may be lower than the
desired level, e.g. when attaching to a device that has too few
available PEBs to satisfy the desired level).

In the case where the device has too many bad PEBs (above the expected
limit), then the desired level, and the actual amount of PEBs reserved
are set to zero. No PEBs will be set aside for future bad eraseblock
handling - even if some PEBs are made available (e.g. by shrinking a
volume).
If another PEB goes bad, and there are available PEBs, then the
eraseblock will be marked bad (consuming one available PEB). But if
there are no available PEBs, ubi will go into readonly mode.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>

Introduce 'ubi->bad_peb_limit', which specifies an upper limit of PEBs
UBI expects to go bad.  Currently, it is initialized to a fixed percentage
of total PEBs in the UBI device (configurable via CONFIG_MTD_UBI_BEB_LIMIT).

The 'bad_peb_limit' is intended to be used for calculating the amount of PEBs
UBI needs to reserve for bad eraseblock handling.

Artem: minor amendments.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>

We are going to kill the CONFIG_MTD_UBI_BEB_RESERVE configuration option soon
and use the CONFIG_MTD_UBI_BEB_LIMIT instead. In order to do this smoothly,
we now introduce the new configuration option to sam9_l9260_defconfig, and
will kill the old one after the corresponding UBI changes are done.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.

Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.

This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull KVM bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix KVM_GET_MSR for PV EOI
  kvm: Fix nonsense handling of compat ioctl

Pull PARISC fixes from James Bottomley:
 "This is a set of two bug fixes.  One is the ATOMIC problem which is
  now causing a compile failure in certain situations.  The other is
  mishandling of PER_LINUX32 which may also cause user visible effects.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] fix personality flag check in copy_thread()
  [PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts

Pull s390 fixes from Martin Schwidefsky:
 "A couple of s390 bug fixes for 3.5-rc4"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/32: Don't clobber personality flags on exec
  s390/smp: add missing smp_store_status() for !SMP
  s390/dasd: fix ioctl return value
  s390: Always use "long" for ssize_t to match size_t

Pull drm fixes from Dave Airlie:
 "A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
  nothing too shocking or different."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
  gma500: Consider CRTC initially active.
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm: Check for invalid cursor flags
  drm: Initialize object type when using DRM_MODE() macro
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions

In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Alex writes:

Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.

* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS

[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]

This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver.  It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board.  Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Pull btrfs fixes from Chris Mason:
 "I've split out the big send/receive update from my last pull request
  and now have just the fixes in my for-linus branch.  The send/recv
  branch will wander over to linux-next shortly though.

  The largest patches in this pull are Josef's patches to fix DIO
  locking problems and his patch to fix a crash during balance.  They
  are both well tested.

  The rest are smaller fixes that we've had queued.  The last rc came
  out while I was hacking new and exciting ways to recover from a
  misplaced rm -rf on my dev box, so these missed rc3."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
  Btrfs: fix that repair code is spuriously executed for transid failures
  Btrfs: fix ordered extent leak when failing to start a transaction
  Btrfs: fix a dio write regression
  Btrfs: fix deadlock with freeze and sync V2
  Btrfs: revert checksum error statistic which can cause a BUG()
  Btrfs: remove superblock writing after fatal error
  Btrfs: allow delayed refs to be merged
  Btrfs: fix enospc problems when deleting a subvol
  Btrfs: fix wrong mtime and ctime when creating snapshots
  Btrfs: fix race in run_clustered_refs
  Btrfs: don't run __tree_mod_log_free_eb on leaves
  Btrfs: increase the size of the free space cache
  Btrfs: barrier before waitqueue_active
  Btrfs: fix deadlock in wait_for_more_refs
  btrfs: fix second lock in btrfs_delete_delayed_items()
  Btrfs: don't allocate a seperate csums array for direct reads
  Btrfs: do not strdup non existent strings
  Btrfs: do not use missing devices when showing devname
  Btrfs: fix that error value is changed by mistake
  Btrfs: lock extents as we map them in DIO
  ...

Pull watchdog fixes from Wim Van Sebroeck:
 "This will fix a warning for watchdog-test.c and it will remove a
  duplicate include of delay.h"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: da9052: Remove duplicate inclusion of delay.h
  watchdog: fix watchdog-test.c build warning

cache_grow() can reenable irqs so the cpu (and node) can change, so ensure
that we take list_lock on the correct nodelist.

This fixes an issue with commit 072bb0aa ("mm: sl[au]b: add
knowledge of PFMEMALLOC reserve pages") where list_lock for the wrong
node was taken after growing the cache.
Reported-and-tested-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.

https://bugzilla.redhat.com/show_bug.cgi?id=785375Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Adjust the panel mode setup to match the behavior
of the vbios.  Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Power gating is per crtc pair, but the powergating registers
should be called individually.  The hw handles power up/down
properly.  The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down.  This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders.  We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs.  This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Some plls are shared for DP.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>

Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This should help catch uninitialized registers and reject commands
because of that.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

delay.h header file was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Fix compiler warning by making the function static:

Documentation/watchdog/src/watchdog-test.c:34:6: warning: no previous prototype for 'term'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Daniel writes:

"Just a few smaller things:
- Fix up a pipe vs. plane confusion from a refactoring, fixes a regression
  from 3.1 (Anhua Xu).
- Fix ivb sprite pixel formats (Vijay).
- Fixup ppgtt pde placement for machines where the Bios artifically limits
  the availbale gtt space in the name of ... product differentiation
  (Chris). This fixes an oops.
- Yet another no_lvds quirk entry."

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions

Merge branch 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes

Ben says its just a single fix to avoid the wrong pcopy units being used.

* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled

On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist.  And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.

This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.

Cc: stable@vger.kernel.org [3.5]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

If verify_parent_transid() fails for all mirrors, the current code
calls repair_io_failure() anyway which means:
- that the disk block is rewritten without repairing anything and
- that a kernel log message is printed which misleadingly claims
  that a read error was corrected.

This is an example:
parent transid verify failed on 615015833600 wanted 110423 found 110424
parent transid verify failed on 615015833600 wanted 110423 found 110424
btrfs read error corrected: ino 1 off 615015833600 (dev /dev/...)

It is wrong to ignore the results from verify_parent_transid() and to
call repair_eb_io_failure() when the verification of the transids failed.
This commit fixes the issue.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

We cannot just return error before freeing ordered extent and releasing reserved
space when we fail to start a transacion.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

This bug is introduced by commit 3b8bde746f6f9bd36a9f05f5f3b6e334318176a9
(Btrfs: lock extents as we map them in DIO).

In dio write, we should unlock the section which we didn't do IO on in case that
we fall back to buffered write.  But we need to not only unlock the section
but also cleanup reserved space for the section.

This bug was found while running xfstests 133, with this 133 no longer complains.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>