- 24 Apr, 2020 21 commits
-
-
Luca Coelho authored
Some So devices have a longer wake latency. To support this properly, add new cfg structs for them so the driver will inform the FW about the need to use another xtal and use a higher wait value during state transitions. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.daf515618f57.I80e60006b108e1586e3c56669635c670597fe08d@changeid
-
Luca Coelho authored
Some Qu devices require an intermediate amount of time to wake up and for LTR notifications, so add a new structure with the correct values for them and change the corresponding devices to use it. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.d6df2bcee78f.Ie008b0c8f03340a466c1ef981bfd25359c9de90d@changeid
-
Johannes Berg authored
Some (integrated) devices need a longer LTR delay than the firmware would typically apply, tell it about that. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.24276ae2ad61.I8831a538f75893d5cee47b4a81f4b9b7fd0e8bea@changeid
-
Ihab Zhaika authored
update the product names of few structs in AX family. Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.738dabad8732.I5673eaf8a016b8aa27ab8bab02121108fa723783@changeid
-
Luca Coelho authored
A new device ID needs to be added to the list to support new SoCs. Add it and support all subsystem IDs that other Qu devices support. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.5e5ce668ff8b.I20a9c8b3470aaabaa54361a5641637e5a14d8321@changeid
-
Ihab Zhaika authored
add few PCI ID'S for AX family. Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.5eae2261b70c.I0369619a562c4e4008e2f0a3afb9ed5d4c9b49d4@changeid
-
Mordechay Goodstein authored
Read the Time Averaged SAR (TAS) table from ACPI and if TAS feature is enabled in the FW send the black list countries which TAS is disabled in to the FW Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.40a327d32cfd.I7203f3afc8186cca34c48a1a116baac1df5eff4e@changeid
-
Emmanuel Grumbach authored
This module parameter is no longer useful now that other debug infrastructure was added to iwlwifi. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.03bd49c3432b.Ie62047d3b364b19c8c3584ea37790220466f2a8d@changeid
-
Luca Coelho authored
This struct hasn't been used in years and is just a remnant of an API support removal that missed this structured. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.93860da2d12a.Ifeca3b3313e3f14330317bc3e3d62f7d991ec955@changeid
-
Gil Adam authored
Add framework for supporting specific PHY filter configuration, which allows for application of various FW defined PHY filters (one per antenna). Change phy_cfg_cmd to the new API (ver3). Reading of configuration from platform's ACPI tables to be added later when tables are defined. Signed-off-by: Gil Adam <gil.adam@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.242a8f979592.I13c77a8a8dbf1a169b5052c7af1f8401ff3991ad@changeid
-
Johannes Berg authored
There's no need for this to be an inline in the header file, only the context-info.c file ever uses it. Move it there. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.818a06457888.Ib4f55280cd14d7edab37f2992b381c9b6ca4cd7a@changeid
-
Shahar S Matityahu authored
Allow the driver to perform dump collection in case of alive notification timeout in yoyo mode. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200417131727.bd46e6240590.Ibda6d9d330a1ae49670152cede34629b280f6cf9@changeid
-
Johannes Berg authored
It's useful to know if DCM was enabled, add this flag to the rate pretty-printer. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200417131727.891bb9741eca.Ia66448f7e00be9e4c9ea7147b90d4fcd5f1d3845@changeid
-
Johannes Berg authored
One line should be indented less, otherwise it looks like it belongs into the parentheses, which clearly it doesn't; also some variables can move into their respective if branches. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200417131727.a4858aa0441b.I0e70e4a5493fe6b8db6390f9349ff0e7888ab240@changeid
-
Johannes Berg authored
Add the n_window and ampdu parameters so we can see them. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200417131727.a2cc1f36008f.Iea23802bb64a08de410223e9af4431dfcadf121b@changeid
-
Johannes Berg authored
On newer hardware, the tx_queue debugfs file would need to allocate 37.5kib data since there are 512 queues, which is too much. Rather than resorting to kludges like kvmalloc(), use the seq_file API to print out the data. While at it, also fix a NULL pointer dereference here, the txq pointer from trans_pcie->txqs[] may be NULL if that queue hasn't been allocated. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200417131727.491cf8224c49.I7f154d81e5becef3b5ff22d7c6e36170bde0d7d5@changeid
-
Mordechay Goodstein authored
Add support for the new WOWLAN_GET_STATUS notification that contains a new element that informs the driver of TIDs whose BA sessions were closed during suspend. Note that the new functionality of handling these closed sessions is not implemented in this patch it. It only aligns to the new API version. Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200417131727.b02153b94c1d.Ieb6291586d60f372d5a505604b18227ef97e7202@changeid
-
Shahar S Matityahu authored
Support multiple debug data collection triggers in legacy flow. Utilize the already existing Yoyo infra so the change is rather simple. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200417131727.5be6a1923cbe.I10701236b03f66328041f2a38f5f0f22a26fd40b@changeid
-
Mordechay Goodstein authored
The API version lookup is parsed from a TLV and should be in shared code make make it reusable across all opmodes. Also change the function names from mvm to fw, since this is not mvm-specific anymore. Additionally, since this function is not just a single line of code, it shouldn't be inline. Convert them to actual functions. Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200421133326.cf94672dfcdb.I5ede9cc25ee8de7b8d2b5c574f917a18971da734@changeid
-
Tova Mussai authored
Use iwl_nl80211_band_from_channel_idx in iwl_parse_nvm_mcc_info Signed-off-by: Tova Mussai <tova.mussai@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200417131727.a64a018f244e.Ie75ac5bb0f0f524d26944800138855ef2228339a@changeid
-
Tova Mussai authored
The fw already supports scan api v14 and the firmware version that supports only v13 was not published, so we can remove support for v13 in the driver. Signed-off-by: Tova Mussai <tova.mussai@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200417131727.11883315579a.I4f59100e457c1079c5e4c90e4930d1fa62b7ddd7@changeid
-
- 23 Apr, 2020 9 commits
-
-
Ping-Ke Shih authored
Implement rtw_chip_ops::phy_set_param and ::mac_init to initialize mac/bb/rf, and they are used during interface up. The procedure contains power on sequence registers, download firmware, load predefined parameters, mac/bb/rf specific register and etc. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200422034607.28747-9-yhchuang@realtek.com
-
Ping-Ke Shih authored
TX FIFO size is 32k and it was divided into 256 pages with 128 bytes. A boundary is used to split pages into two parts, head part is used to store TX packets coming from host, and tail part is reserved for special purposes, such as beacon packet, null data packet and so on. The TX packets coming from host have many categories, such as VO, VI, BE, BK, MG and etc. When going into head part of TX FIFO, they are classified to four priority queue named low, normal, high and extra priority queues. Each priority queue occupies predefined number of page, if a certain priority queue is full, TX packet will store into PUB priority queue. Similarly, RX FIFO is 16k and split into two parts, head part is used to store RX packets, and tail part is 128 bytes and used to store report. Thus, we fill this boundary to register as well. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200422034607.28747-8-yhchuang@realtek.com
-
Ping-Ke Shih authored
The txagc table is used to map rate_id and txagc register address and mask, and ops set_tx_power_index uses this table to write TX power to corresponding registers. Since 8723D is a 1x1 2.4G 11n chip, only CCK, OFDM and HT_MCS 0-7 are listed in the table. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200422034607.28747-7-yhchuang@realtek.com
-
Ping-Ke Shih authored
H2C queue is used to send command to firmware. Since 8723D doesn't support this queue, this commit check wlan_cpu flag to avoid to set H2C related registers. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200422034607.28747-6-yhchuang@realtek.com
-
Ping-Ke Shih authored
The power polling command is one kind of power sequence commands. It's used to check hardware situation, and subsequent comamnds will be executed if hardware is ready. A special case is PCIE must toggle BIT_PFM_WOWL and try again if first try is failed. In order to reduce indentation to understand the code easier, move polling part to a separate function. Then, the 'while (1)...loop' is replaced by two statements to do first try and retry. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200422034607.28747-5-yhchuang@realtek.com
-
Ping-Ke Shih authored
The mac power-on flow consists of three steps: 1. pre_sys_cfg (Before switching power state) 2. power_switch (Switching power state) 3. init_sys_cfg (Settings after swtiching power state) When switching power state, driver will load and parse the power sequence tables. For 8723D devices, the logics for parsing are most same except for the polling function. 8723D devices need to toggle BIT_PFM_WOWL twice. The settings after power state is switched for 8723D devices are quite different with other devices, extract a legacy function for them. For power-off flow, 8723D devices have the same logic with existing chips. But warning printed if we run power-off sequence in power-off state: rtw_pci 0000:03:00.0: failed to poll offset=0x5f8 mask=0xff value=0x0 The scenario is user do 'ifconfig up' that will run power-on sequence to bring up and then run power-off sequence to enter idle (IEEE80211_CONF_IDLE). Then, user do 'ifconfig down' that will run power-off sequence again, and the warning is shown. Original code check power-on state to avoid to run power-on sequence twice, and this commit extends to check both power-on and power-off states. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200422034607.28747-4-yhchuang@realtek.com
-
Ping-Ke Shih authored
The firmware of 11AC devices need more information to support more offload functions, such as IQK. And 11N devices such as 8723D does not support offload these function in firmware, there is no need to send these additional information to firmware when it comes to 11N devices. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200422034607.28747-3-yhchuang@realtek.com
-
Ping-Ke Shih authored
The WLAN CPU of 8723D device is different from others, add legacy firmware download function for it. A new variable wlan_cpu is used to decide which firmware download function we should use. Legacy firmware file contains 32 bytes header including version and subversion. When downloading to wlan cpu, header is excluded. Firmware is downloaded via beacon queue to reserved page that is a part of TX buffer. Since 11N WLAN CPU uses different control registers, this patch introduces related control registers. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200422034607.28747-2-yhchuang@realtek.com
-
Raz Bouganim authored
This patch adding support for new cipher suite - AES-CMAC in wlcore driver. This patch is required for support PMF/WPA3 connection to install IGTK key. Signed-off-by: Raz Bouganim <r-bouganim@ti.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1587472085-755-1-git-send-email-r-bouganim@ti.com
-
- 21 Apr, 2020 10 commits
-
-
Tzu-En Huang authored
8822C devices have power trim, thermal and PA bias values programmed in efuse. Driver should configure the RF components according to the values. If the power trim is not configured, then the devices might have distortion on the output tx power. Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420105207.31899-1-yhchuang@realtek.com
-
Ping-Ke Shih authored
The logical efuse map is decoded from physical map by parsing the header format of the physical map. And each different type of chips has different logical efuse layout. So add the logical map's layout for parsing the efuse contents. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420055054.14592-9-yhchuang@realtek.com
-
Ping-Ke Shih authored
8723D devices need to grant efuse access before dumping physical efuse map, other chips don't need it, so keep this ops as blank. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420055054.14592-8-yhchuang@realtek.com
-
Ping-Ke Shih authored
Implement rtw_chip_ops::cfg_ldo25 to enable/disable LDO25 with proper voltage. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420055054.14592-7-yhchuang@realtek.com
-
Ping-Ke Shih authored
Add corresponding parameter tables for 8723D devices. Since 8723D devices currently have only one RFE type, there is only one entry in rtw8723d_rfe_defs. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420055054.14592-6-yhchuang@realtek.com
-
Ping-Ke Shih authored
8723D use SIPI to indirectly read RF register instead of directly read, so introduce a new struct rtw_rf_sipi_addr and new function rtw_phy_read_rf_sipi(). Since other chips don't use the new function, only 8723D needs to fill struct rtw_rf_sipi_addr in rtw_chip_info. Because there are two kinds of functions for reading RF registers now, change rtw_phy_read_rf() to chip->ops->read_rf() in rtw_phy_write_rf_reg_sipi() so that we can switch tp proper RF read functions depends on the type of the chip. Though 8723D is an 1x1 chip, it has two RF PHY and we can switch to one of them, and that should be configured properly. Hence, add a fix_rf_phy_num to struct rtw_chip_info to allow driver to set one of the PHY's registers for 8723D, even it is only 1x1. Another variable rf_phy_num is introduced to keep the constraint number of RF path we can access, and its value is: rf_phy_num = (fix_rf_phy_num ? fix_rf_phy_num : rf_path_num) Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420055054.14592-5-yhchuang@realtek.com
-
Ping-Ke Shih authored
Add corresponding power sequence for 8723D devices Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420055054.14592-4-yhchuang@realtek.com
-
Ping-Ke Shih authored
8723D doesn't support beamform because rtw88 only supports VHT beamform but 8723d doesn't have VHT capability. Though 8723d doesn't support beamform, BSS_CHANGED_MU_GROUPS is still marked as changed when doing disassociation. So, add wrapper functions for all beamform ops to make sure they aren't NULL before calling. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420055054.14592-3-yhchuang@realtek.com
-
Ping-Ke Shih authored
RTL8723DE is an 11n 1x1 2.4G single band chip with the following capabilities: - TX/RX BD size: 16/8 - TX/RX desc size: 40/24 - physical/logical/protected efuse size: 512/512/96 - TX gain index factor: 1 - max TX power index: 0x3F - band: 2G - HT: support - VHT: Not support Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420055054.14592-2-yhchuang@realtek.com
-
Jason Yan authored
Fix the following coccicheck warning: drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:617:14-20: WARNING: Comparison to bool drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:622:13-19: WARNING: Comparison to bool drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:627:14-20: WARNING: Comparison to bool drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:632:13-19: WARNING: Comparison to bool drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hw.c:937:5-13: WARNING: Comparison to bool Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200420042658.18733-1-yanaijie@huawei.com
-