In former commit, drivers in ALSA firewire stack always starts IT context
before IR context. If IR context starts after packets are transmitted by
peer unit, packet discontinuity may be detected because the context starts
in the middle of packet streaming. This situation is rare because IT
context usually starts immediately. However, it's better to solve this
issue. This is suppressed with CIP_SKIP_INIT_DBC_CHECK flag.

This commit enables the same feature as CIP_SKIP_INIT_DBC_CHECK.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In previous commit, this module has no need to reuse parameters of
incoming packets for outgoing packets anymore. This commit arranges some
needless codes for outgoing packet processing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In previous commit, this module has no need to reuse parameters of
incoming packets for outgoing packets anymore. This commit arranges some
needless codes for incoming packet processing.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In clause 6.3 of IEC 61883-6:2000, there's an explanation about processing
of presentation timestamp. In the clause, we can see "If a function block
receives a CIP, processes it and subsequently re-transmits it, then the
SYT of the outgoing CIP shall be the sum of the incoming SYT and the
processing delay." ALSA firewire stack has an implementation to partly
satisfy this specification. Developers assumed the stack to perform as an
Audio function block[1].

Following to the assumption, current implementation of ALSA firewire stack
use one software interrupt context to handle both of in/out packets. In
most case, this is processed in 1394 OHCI IR context independently of the
opposite context. Thus, this implementation uses longer CPU time in the
software interrupt context. This is not better for whole system.

Against the assumption, I confirmed that each ASIC for IEC 61883-1/6
doesn't necessarily expect it to the stack. Thus, current implementation
of ALSA firewire stack includes over-engineering.

This commit purges the implementation. As a result, packets of one
direction are handled in one software interrupt context and spends
minimum CPU time.

[1] [alsa-devel] [PATCH 0/8] [RFC] new driver for Echo Audio's Fireworks based devices
http://mailman.alsa-project.org/pipermail/alsa-devel/2013-June/062660.htmlSigned-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In packet streaming protocol applied to TASCAM FireWire series, the value
of SYT field in CIP header is always zero, therefore it has no meaning.
There's no need to synchronize packets in both direction for the series.

In current implementation of ALSA firewire stack, driver for the series
uses incoming packet parameter for outgoing packet parameter to calculate
the number of data blocks. This can be simplified because the task of
corresponding driver is to transfer data blocks enough to sampling transfer
frequency.

This commit purges support of full duplex synchronization to prevent
over-engineering implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

On Fireworks board module of Echo Audio, TSB43Cx43A (IceLynx Micro, iCEM)
is used to process payload of isochronous packets. There's an public
document of this chip[1]. This document is for firmware programmers to
transfer/receive AMDTP with IEC60958 data format, however in clause 2.5,
2.6 and 2.7, we can see system design to utilize the sequence of value in
SYT field of CIP header. In clause 2.3, we can see the specification of
Audio Master Clock (MCLK) from iCEM.

Well, this clock is actually not used for sampling clock. This can be
confirmed when corresponding driver transfer random value as the sequence
of SYT field. Even if in this case, the unit generates proper sound.

Additionally, in unique command set for this board module, the format
of CIP is changed; for IEC 61883-6 mode which we use, and for Windows
Operating System. In the latter mode, the whole 32 bit field in second CIP
header from Windows driver is used to represent counter of packets (NO-DATA
code is still used for packets without data blocks). If the master clock
was physically used by DSP on the board module, the Windows driver must
have transferred correct sequence of SYT field.

Furthermore, as long as seeing capacities of AudioFire2, AudioFire4,
AudioFire8, AudioFirePre8 and AudioFire12, these models don't support
SYT-Match clock source.

Summary, we have no need to relate incoming/outgoing packets. This commit
drops reusing SYT sequence of incoming packets for outgoing packets.

[1] Using TSB43Cx43A: S/PDIF over 1394 (2003, Texus Instruments
Incorporated)
http://www.ti.com/analog/docs/litabsmultiplefilelist.tsp?literatureNumber=slla148&docCategoryId=1&familyId=361Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Windows driver for BeBoB-based models mostly wait for transmitted packets,
then transfer packets to the models. This looks for the relationship
between incoming packets and outgoing packets to synchronize the sequence
of presentation timestamp.

However, the sequence between packets of both direction has no
relationship. Even if receiving NO-DATA packets, the drivers transfer
packets with meaningful value in SYT field. Additionally, the order of
starting packets is always the same, independently of the source of clock.
The corresponding driver is expected as a generator of presentation
timestamp and these models can select it as a source of sampling clock.

This commit drops reusing SYT sequence from ALSA bebob driver. The driver
always transfer packets with presentation timestamp generated by ALSA
firewire stack, without re-using the sequence of value in SYT field in
incoming packets to outgoing packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Subwoofer does not work out of the box on ASUS N751/N551 laptops. This
patch fixes it. Patch tested on N751 laptop. N551 part is not tested,
but according to [1] and [2] this laptop requires similar changes, so I
included them in the patch.

1. https://github.com/honsiorovskyi/asus-n551-hda-fix
2. https://bugs.launchpad.net/ubuntu/+source/alsa-tools/+bug/1405691

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117781Signed-off-by: Yura Pakhuchiy <pakhuchiy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The HD-audio reconfig function got broken in the recent kernels,
typically resulting in a failure like:
  snd_hda_intel 0000:00:1b.0: control 3:0:0:Playback Channel Map:0 is already present

This is because of the code restructuring to move the PCM and control
instantiation into the codec drive probe, by the commit [bcd96557:
ALSA: hda - Build PCMs and controls at codec driver probe].  Although
the commit above removed the calls of snd_hda_codec_build_pcms() and
*_build_controls() at the controller driver probe, the similar calls
in the reconfig were still left forgotten.  This caused the
conflicting and duplicated PCMs and controls.

The fix is trivial: just remove these superfluous calls from
reconfig_codec().

Fixes: bcd96557 ('ALSA: hda - Build PCMs and controls at codec driver probe')
Reported-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Since the recent rewrite of HD-audio infrastructure,
CONFIG_SND_HDA_RECONFIG has a slightly different meaning.  In the
earlier versions, it implicitly assumed only the usage via hwdep sysfs
entries.  Meanwhile, in the recent version, this option is meant to
enable the reconfig code in HD-audio driver, which may be used by the
patch loader without hwdep interface.

This patch tries to clarify the usage pattern a bit better, hopefully
avoid the further confusion.
Reported-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A switch statement looks a bit cleaner than an if statement
spread over 3 lines, as such update this to a switch.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We can't return a negative error code from the poll callback the return
type is unsigned and is checked against the poll specific flags we need
to return POLLERR if we encounter an error.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

stream can't be NULL here as we have just taken the address of it, so no
need for the check.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We have a function that returns the appropriate flags for the stream
direction, so we should use it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We can't return a negative error code from the poll callback the return
type is unsigned and is checked against the poll specific flags we need
to return POLLERR if we encounter an error.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When audio and music units have some quirks in their sequence of packet,
it's really hard for non-owners to identify the quirks. Although developers
need dumps for sequence of packets, it's difficult for users who have no
knowledges and no equipments for this purpose.

This commit adds tracepoints for this situation. When users encounter
the issue, they can dump a part of packet data via Linux tracing framework
as long as using drivers in ALSA firewire stack.

Additionally, tracepoints for outgoing packets will be our help to check
and debug packet processing of ALSA firewire stack.

This commit newly adds 'snd_firewire_lib' subsystem with 'in_packet' and
'out_packet' events. In the events, some attributes of packets and the
index of packet managed by this module are recorded per packet.

This is an usage:

$ trace-cmd record -e snd_firewire_lib:out_packet \
                   -e snd_firewire_lib:in_packet
/sys/kernel/tracing/events/snd_firewire_lib/out_packet/filter
/sys/kernel/tracing/events/snd_firewire_lib/in_packet/filter
Hit Ctrl^C to stop recording
^C
$ trace-cmd report trace.dat
...
23647.033934: in_packet:  01 4073 ffc0 ffc1 00 000f0040 9001b2d1 122 44
23647.033936: in_packet:  01 4074 ffc0 ffc1 00 000f0048 9001c83b 122 45
23647.033937: in_packet:  01 4075 ffc0 ffc1 00 000f0050 9001ffff 002 46
23647.033938: in_packet:  01 4076 ffc0 ffc1 00 000f0050 9001e1a6 122 47
23647.035426: out_packet: 01 4123 ffc1 ffc0 01 010f00d0 9001fb40 122 17
23647.035428: out_packet: 01 4124 ffc1 ffc0 01 010f00d8 9001ffff 002 18
23647.035429: out_packet: 01 4125 ffc1 ffc0 01 010f00d8 900114aa 122 19
23647.035430: out_packet: 01 4126 ffc1 ffc0 01 010f00e0 90012a15 122 20
(Here, some common fields are omitted so that a line to be within 80
characters.)
...

One line represent one packet. The legend for the last nine fields is:
 - The second of cycle scheduled for the packet
 - The count of cycle scheduled for the packet
 - The ID of node as source (hex)
  - Some devices transfer packets with invalid source node ID in their CIP
    header.
 - The ID of node as destination (hex)
  - The value is not in CIP header of packets.
 - The value of isochronous channel
 - The first quadlet of CIP header (hex)
 - The second quadlet of CIP header (hex)
 - The number of included quadlets
 - The index of packet in a buffer maintained by this module

This is an example to parse these lines from text file by Python3 script:

\#!/usr/bin/env python3
import sys

def parse_ts(second, cycle, syt):
    offset = syt & 0xfff
    syt >>= 12
    if cycle & 0x0f > syt:
        cycle += 0x10
    cycle &= 0x1ff0
    cycle |= syt
    second += cycle // 8000
    cycle %= 8000
    # In CYCLE_TIMER of 1394 OHCI, second is represented in 8 bit.
    second %= 128
    return (second, cycle, offset)

def calc_ts(second, cycle, offset):
    ts = offset
    ts += cycle * 3072
    # In DMA descriptor of 1394 OHCI, second is represented in 3 bit.
    ts += (second % 8) * 8000 * 3072
    return ts

def subtract_ts(minuend, subtrahend):
    # In DMA descriptor of 1394 OHCI, second is represented in 3 bit.
    if minuend < subtrahend:
        minuend += 8 * 8000 * 3072
    return minuend - subtrahend

if len(sys.argv) != 2:
    print('At least, one argument is required for packet dump.')
    sys.exit()

filename = sys.argv[1]

data = []

prev = 0
with open(filename, 'r') as f:
    for line in f:
        pos = line.find('packet:')
        if pos < 0:
            continue

        pos += len('packet:')
        line = line[pos:].strip()
        fields = line.split(' ')

        datum = []

        datum.append(fields[8])

        syt = int(fields[6][4:], 16)

        # Empty packet in IEC 61883-1, or NODATA in IEC 61883-6
        if syt == 0xffff:
            data_blocks = 0
        else:
            payload_size = int(fields[7], 10)
            data_block_size = int(fields[5][2:4], 16)
            data_blocks = (payload_size - 2) / data_block_size
        datum.append(data_blocks)

        second = int(fields[0], 10)
        cycle = int(fields[1], 10)
        start = (second << 25) | (cycle << 12)
        datum.append('0x{0:08x}'.format(start))
        start = calc_ts(second, cycle, 0)

        datum.append("0x" + fields[5])
        datum.append("0x" + fields[6])

        if syt == 0xffff:
            second = 0
            cycle = 0
            tick = 0
        else:
            second, cycle, tick = parse_ts(second, cycle, syt)
        ts = calc_ts(second, cycle, tick)
        datum.append(start)
        datum.append(ts)
        if ts == 0:
            datum.append(0)
            datum.append(0)
        else:
            # Usual case, or a case over 8 seconds.
            if ts > start or start > 7 * 8000 * 3072:
                datum.append(subtract_ts(ts, start))
                if ts > prev or start > 7 * 8000 * 3072:
                    gap = subtract_ts(ts, prev)
                    datum.append(gap)
                else:
                    datum.append('backward')
            else:
                datum.append('invalid')
            prev = ts

        data.append(datum)

sys.exit()

The data variable includes array with these elements:
- The index of the packet
- The number of data blocks in the packet
- The value of cycle count (hex)
- The value of CIP header 1 (hex)
- The value of CIP header 2 (hex)
- The value of cycle count (tick)
- The value of calculated presentation timestamp (tick)
- The offset between the cycle count and presentation timestamp
- The elapsed ticks from the previous presentation timestamp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In callback function of isochronous context, modules can queue packets to
indicated isochronous cycles. Although the cycle to queue a packet is
deterministic by calculation, this module doesn't implement the calculation
because it's useless for processing.

In future, the cycle count is going to be printed with the other parameters
for debugging. This commit is the preparation. The cycle count is computed
by cycle unit, and correctly arranged to corresponding packets. The
calculated count is used in later commit.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In callback function of isochronous context, u32 variable is passed for
cycle count. The value of this variable comes from DMA descriptors of 1394
Open Host Controller Interface (1394 OHCI). In the specification, DMA
descriptors transport lower 3 bits for second field and full cycle field in
16 bits field, therefore 16 bits of the u32 variable are available. The
value for second is modulo 8, and the value for cycle is modulo 8,000.

Currently, ALSA firewire-lib module don't use the value of the second
field, because the value is useless to calculate presentation timestamp in
IEC 61883-6. However, the value may be useful for debugging. In later
commit, it will be printed with the other parameters for debugging.

This commit makes this module to handle the whole cycle count including
second. The value is calculated by cycle unit. The existed code is already
written with ignoring the value of second, thus this commit causes no
issues.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

For reducing the noise from the headset output on ASUS UX501VW,
call the existing fixup, alc_fixup_headset_mode_alc668(), additionally.

Thread: https://bbs.archlinux.org/viewtopic.php?id=209554Signed-off-by: Kaho Ng <ngkaho1234@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

If the DMAs are not being quiesced properly, it may lead to
stability issues, so the recommendation is to wait till DMAs are
stopped.

After setting the stop bit of RIRB/CORB DMA, we should wait for
stop bit to be set.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ebus is a member of extended device and was never initialized, so
do this at device creation.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Allow for SS+ USB devices
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Allow handling SS+ USB devices correctly.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Support new codecs for ALC234/ALC274/ALC294.
This three codecs was the same IC.
But bonding is not the same.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

"header->number" can be up to USHRT_MAX and it comes from the ioctl so
it needs to be capped.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The stack object “tread” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Noticed two typos in Documentation, so fix them up
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

M-Audio Profire 610 has an unexpected value in version field of its config
ROM, thus ALSA dice driver is not assigned to the model due to a mismatch
of modalias.

This commit adds an entry to support the model. I expect the entry is
also for Profire 2626.

I note that Profire 610 uses TCD2220 (so-called Dice Jr.), and supports a
part of Extended Application Protocol (EAP).

$ cd linux-firewire-utils/src
$ ./crpp < /sys/bus/firewire/devices/fw1/config_rom
               ROM header and bus information block
               ------------------------------------------------------------
400  04047689  bus_info_length 4, crc_length 4, crc 30345
404  31333934  bus_name "1394"
408  e0ff8112  irmc 1, cmc 1, isc 1, bmc 0, pmc 0, cyc_clk_acc 255,
               max_rec 8 (512), max_rom 1, gen 1, spd 2 (S400)
40c  000d6c04  company_id 000d6c     |
410  04400002  device_id 0404400002  | EUI-64 000d6c0404400002

               root directory
               ------------------------------------------------------------
414  000695fe  directory_length 6, crc 38398
418  03000d6c  vendor
41c  8100000a  --> descriptor leaf at 444
420  17000011  model
424  8100000d  --> descriptor leaf at 458
428  0c0087c0  node capabilities per IEEE 1394
42c  d1000001  --> unit directory at 430

               unit directory at 430
               ------------------------------------------------------------
430  0004fb14  directory_length 4, crc 64276
434  12000d6c  specifier id
438  130100d1  version
43c  17000011  model
440  8100000c  --> descriptor leaf at 470

               descriptor leaf at 444
               ------------------------------------------------------------
444  0004b8e4  leaf_length 4, crc 47332
448  00000000  textual descriptor
44c  00000000  minimal ASCII
450  4d2d4175  "M-Au"
454  64696f00  "dio"

               descriptor leaf at 458
               ------------------------------------------------------------
458  00053128  leaf_length 5, crc 12584
45c  00000000  textual descriptor
460  00000000  minimal ASCII
464  50726f46  "ProF"
468  69726520  "ire "
46c  36313000  "610"

               descriptor leaf at 470
               ------------------------------------------------------------
470  00053128  leaf_length 5, crc 12584
474  00000000  textual descriptor
478  00000000  minimal ASCII
47c  50726f46  "ProF"
480  69726520  "ire "
484  36313000  "610"

$ cat /proc/asound/card1/dice
sections:
  global: offset 10, size 90
  tx: offset 100, size 142
  rx: offset 242, size 282
  ext_sync: offset 524, size 4
  unused2: offset 0, size 0
global:
  owner: ffc0:000100000000
  notification: 00000040
  nick name: FW610
  clock select: internal 48000
  enable: 1
  status: locked 48000
  ext status: 00000040
  sample rate: 48000
  version: 1.0.4.0
  clock caps: 32000 44100 48000 88200 96000 176400 192000 aes1 aes4 aes adat tdif wc arx1 arx2 internal
  clock source names: SPDIF\AES34\AES56\TOS\AES_ANY\ADAT\ADAT_AUX\Word Clock\Unused\Unused\Unused\Unused\Internal\\
  ...
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Phoenix Audio MT202pcs (1de7:0114) and MT202exe (1de7:0013) need the
same workaround as TMX320 for avoiding the firmware bug.  It fixes the
frequent error about the sample rate inquiries and the slow device
probe as consequence.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117321
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

There are many USB audio devices with buggy firmware that don't react
with the sample rate reading properly.  This often results in the
flood of error messages and slowing down the operation.

The sample rate read back is basically only for confirming the sample
rate setup, and it's not critically important.  As a compromise, in
this patch, we stop the sample rate read back once when the device
gives errors more than tolerance (twice, as of now).  This should
improve most of error cases while we still can catch the firmware
bugginess.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-fix-v4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v4.6

This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development.  The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.

Merge remote-tracking branches 'asoc/fix/arizona', 'asoc/fix/cs35l32', 'asoc/fix/hdac', 'asoc/fix/nau8825' and 'asoc/fix/rt5616' into asoc-linus

For taking back the recent change of HDA HDMI fixes for i915 HSW/BDW.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The recent bug report suggests that BCLK setup for i915 HSW/BDW needs
to be updated at each HDMI hotplug, not only at initialization and
resume.  That is, we need to update HSW_EM4 and HSW_EM5 registers at
ELD notification, too.  Otherwise the HDMI audio may be out of sync
and played in a wrong pitch.

However, the HDA codec driver has no access to the controller
registers, and currently the code managing these registers is in
hda_intel.c, i.e. local to the controller driver.  For allowing the
explicit BCLK update from the codec driver, as in this patch, the
former haswell_set_bclk() in hda_intel.c is moved to hdac_i915.c and
exposed as snd_hdac_i915_set_bclk().  This is called from both the HDA
controller driver and intel_pin_eld_notify() in HDMI codec driver.

Along with this change, snd_hdac_get_display_clk() gets dropped as
it's no longer used.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91410
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Takashi Iwai <tiwai@suse.de>