Adds reset to sysfs which will PERST the card. If load_image_on_perst is set
to "user" or "factory", the PERST will cause that image to be loaded.

load_image_on_perst is set to "user" for production.

"none" could be used for debugging. The PSL trace arrays are preserved which
then can be read through debugfs.

PERST also triggers CAPP recovery. An HMI comes in, which is handled by EEH.
EEH unbinds the driver, calls into Sapphire to reinitialize the PHB, then
rebinds the driver.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Turning snoops on is the last step in CAPP recovery. Sapphire is expected to
have reinitialized the PHB and done the previous recovery steps.

Add mode argument to opal call to do this. Driver can turn snoops off although
it does not currently.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

load_image_on_perst identifies whether a PERST will cause the image to be
flashed to the card. And if so, which image.

Valid entries are: "none", "user" and "factory".

A value of "none" means PERST will not cause the image to be flashed. A
power cycle to the pcie slot is required to load the image.

"user" loads the user provided image and "factory" loads the factory image upon
PERST.

sysfs updates the cxl struct in the driver then calls cxl_update_image_control
to write the vals in the VSEC.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Select defaults such that a PERST causes flash image reload.  Select which
image based on what the card is set up to load.

CXL_VSEC_PERST_LOADS_IMAGE selects whether PERST assertion causes flash image
load.

CXL_VSEC_PERST_SELECT_USER selects which image is loaded on the next PERST.

cxl_update_image_control writes these bits into the VSEC.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This fixes two typos and explains where shared attributes are stored.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch adds tracepoints throughout the cxl driver, which can provide
insight into:

- Context lifetimes
- Commands sent to the PSL and AFU and their completion status
- Segment and page table misses and their resolution
- PSL and AFU interrupts
- slbia calls from the powerpc copro_fault code

These tracepoints are mostly intended to aid in debugging (particularly
for new AFU designs), and may be useful standalone or in conjunction
with hardware traces collected by the PSL (read out via the trace
interface in debugfs) and AFUs.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

hwirq has not been initialized, however it is being incremented
and also not being referenced in a loop.  This error was detected with
cppcheck:

[drivers/misc/cxl/irq.c:439]: (error) Uninitialized variable: hwirq

Commit 80fa93fc ("cxl: Name interrupts in /proc/interrupt")
introduced this error.

This is a simple fix that removes the redundant increment.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fixes warnings like these:

  drivers/ps3/sys-manager-core.c: error: symbol 'ps3_sys_manager_power_off' redeclared with different type
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix sparse warnings like these:

  drivers/ps3/ps3-vuart.c: warning: symbol 'ps3_vuart_disable_interrupt_tx' was not declared. Should it be static?
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add calls to the ps3_mm_set_repository_highmem() routine when the ps3
r1 highmem region is either created or destroyed.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add the new routine ps3_mm_set_repository_highmem() that saves highmem info to
the LV1 hypervisor registry so that the info will be available to second stage
OS's loaded by petitboot/kexec. FreeBSD and some Linux derivatives use
this feature.

Also, move the existing ps3_mm_get_repository_highmem() routine up in
the source file.

This implementation of ps3_mm_set_repository_highmem() assumes the repository
will have a single highmem region entry (at index 0).
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

To avoid the need for preprocessor conditionals in C source files add a set of
empty inline repository highmem write routines to platform.h that are used when
CONFIG_PS3_REPOSITORY_WRITE is not defined.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add CGROUPS and DEVTMPFS, which allows booting with newer userspaces.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Distros are enabling NUMA balancing (eg Ubuntu), so it would be good to
get some more test coverage with it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Enable config options required by lxc and docker.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

KSM will only be used on areas marked for merging via madvise, and it
is showing nice improvements on KVM workloads, so enable it by
default.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We are starting to see ppc64 boxes with SATA AHCI adapters in it,
so enable it in our defconfigs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This was enabled on the pseries defconfigs recently, but missed
the ppc64 one.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

It looks like it's ~4 years since we updated some of these, so do a bulk
update.

Verified that the before and after generated configs are exactly the
same.

Which begs the question why update them? The answer is that it can be
confusing when the stored defconfig drifts too far from the generated
result.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We have two arrays in kvm_host_state that contain register values for
the PMU. Currently we only create an asm-offsets symbol for the base of
the arrays, and do the array offset in the assembly code.

Creating an asm-offsets symbol for each field individually makes the
code much nicer to read, particularly for the MMCRx/SIxR/SDAR fields, and
might have helped us notice the recent double restore bug we had in this
code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Alexander Graf <agraf@suse.de>

In the Makefile, string.o (which is generated from string.S) is
included into the list of objects being built unconditionally
(obj-y) in line 12.

Additionally, if CONFIG_PPC64 is set, it is included again in
line 17.

This patch removes the latter unnecessary inclusion.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 2a2c74b2 ("IBM Akebono: Add the Akebono platform") added a
select of IBM_EMAC_RGMII_WOL. But that Kconfig symbol isn't (yet) part
of the tree. So this select has been a nop since that commit was
included in v3.16-rc1.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When we deactivate the AFU directed mode we free the scheduled process
area, but did not clear the register in the hardware that has a pointer
to it.

This should be fine since we will have already cleared out every context
and we won't do anything that would cause the hardware to access it
until after we have allocated a new one, but just to be safe this patch
clears out the register when we free the page.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Upon inspection of the implementation specific registers, it was
discovered that the high bit of the implementation specific RXCTL
register was enabled, which enables the DEADB00F debug feature.

The debug feature causes MMIO reads to a disabled AFU to respond with
0xDEADB00F instead of all Fs. In general this should not be visible as
the kernel will only allow MMIO access to enabled AFUs, but there may be
some circumstances where an AFU may become disabled while it is use.
One such case would be an AFU designed to only be used in the dedicated
process mode and to disable itself after it has completed it's work
(however even in that case the effects of this debug flag would be
limited as the userspace application must have completed any required
MMIO accesses before the AFU disables itself with or without the flag).

This patch removes the debug flag and replaces the magic value
programmed into this register with a preprocessor define so it is
clearer what the rest of this initialisation does.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

If a context is being detached and we get a translation fault for it
there is little point getting it's mm and handling the fault, so just
respond with an address error and return earlier.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In this particular error path we have already allocated the AFU
interrupts, but have not yet set the status to STARTED. The detach
context code will only attempt to release the interrupts if the context
is in state STARTED, so in this case the interrupts would remain
allocated.

This patch releases the AFU interrupts immediately if the attach call
fails to prevent them leaking.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In case of error, the function ioremap() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

isxdigit() macro definition is the same.

isalnum() from linux/ctype.h will accept additional latin non-ASCII
characters. This is harmless since this macro is used in scanhex() which
parses user input.

isspace() from linux/ctype.h will accept vertical tab and form feed but
not NULL. The use of this macro is modified to accept NULL as
well. Additional characters are harmless since this macro is also only
used in scanhex().
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Moving config DTL up so it is below config PPC_SPLPAR means that
menuconfig will show config DTL nicely indented right below config
PPC_SPLPAR when PPC_SPLPAR is enabled.

To contrast that, right now if I enable PPC_SPLPAR in menuconfig, all I
can immediately tell is that "something showed up further down the list
where I wasn't looking", and I end up having to toggle the option a few
times to figure out what showed up, or look at the KConfig to find out
that config DTL depends on config PPC_SPLPAR.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull KVM fixes from Paolo Bonzini:
 "The important fixes are for two bugs introduced by the merge window.

  On top of this, add a couple of WARN_ONs and stop spamming dmesg on
  pretty much every boot of a virtual machine"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: warn on more invariant breakage
  kvm: fix sorting of memslots with base_gfn == 0
  kvm: x86: drop severity of "generation wraparound" message
  kvm: x86: vmx: reorder some msr writing

Pull vfs fix from Al Viro:
 "An embarrassing bug in lustre patches from this cycle ;-/"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  [regression] braino in "lustre: use is_root_inode()"

Modifying a non-existent slot is not allowed.  Also check that the
first loop doesn't move a deleted slot beyond the used part of
the mslots array.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Before commit 0e60b079 (kvm: change memslot sorting rule from size
to GFN, 2014-12-01), the memslots' sorting key was npages, meaning
that a valid memslot couldn't have its sorting key equal to zero.
On the other hand, a valid memslot can have base_gfn == 0, and invalid
memslots are identified by base_gfn == npages == 0.

Because of this, commit 0e60b079 broke the invariant that invalid
memslots are at the end of the mslots array.  When a memslot with
base_gfn == 0 was created, any invalid memslot before it were left
in place.

This can be fixed by changing the insertion to use a ">=" comparison
instead of "<=", but some care is needed to avoid breaking the case
of deleting a memslot; see the comment in update_memslots.

Thanks to Tiejun Chen for posting an initial patch for this bug.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull sound fixes from Takashi Iwai:
 "Just a couple of fixes for the new Intel Skylake HD-audio support"

* tag 'sound-3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda_intel: apply the Seperate stream_tag for Skylake
  ALSA: hda_controller: Separate stream_tag for input and output streams.

Since most virtual machines raise this message once, it is a bit annoying.
Make it KERN_DEBUG severity.

Cc: stable@vger.kernel.org
Fixes: 7a2e8aafSigned-off-by: Paolo Bonzini <pbonzini@redhat.com>

The commit 34a1cd60, "x86: vmx: move some vmx setting from
vmx_init() to hardware_setup()", tried to refactor some codes
specific to vmx hardware setting into hardware_setup(), but some
msr writing should depend on our previous setting condition like
enable_apicv, enable_ept and so on.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

In one of the places (ll_md_blocking_ast()) we had open-coded
!is_root_inode(inode) and replaced it with is_root_inode(inode).
See the last chunk of f76c23:
-                   inode != inode->i_sb->s_root->d_inode)
+                   is_root_inode(inode))
should've been
+                   !is_root_inode(inode))
obviously...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>