- 01 Jul, 2013 29 commits
-
-
Xiong Zhang authored
On DevCPT, the control register for Transcoder DP Sync Polarity is TRANS_DP_CTL, not DP_CTL. Without this patch, Many call trace occur on CPT machine with DP monitor. The call trace is like: *ERROR* mismatch in adjusted_mode.flags(expected X,found X) v2: use intel-crtc to simple patch, suggested by Daniel. Signed-off-by:
Xiong Zhang <xiong.y.zhang@intel.com> [danvet: Extend the encoder->get_config comment to specify that we now also depend upon intel_encoder->base.crtc being correct. Also bikeshed s/intel_crtc/crtc/.] Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65287Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Daniel Vetter authored
Our interrupt handler (in hardirq context) could race with the timer (in softirq context), hence we need to hold the spinlock around the call to ->hdp_irq_setup in intel_hpd_irq_handler, too. But as an optimization (and more so to clarify things) we don't need to do the irqsave/restore dance in the hardirq context. Note also that on ilk+ the race isn't just against the hotplug reenable timer, but also against the fifo underrun reporting. That one also modifies the SDEIMR register (again protected by the same dev_priv->irq_lock). To lock things down again sprinkle a assert_spin_locked. But exclude the functions touching SDEIMR for now, I want to extract them all into a new helper function (like we do already for pipestate, display interrupts and all the various gt interrupts). v2: Add the missing 't' Egbert spotted in a comment. v3: Actually fix the right misspelled comment (Paulo). Cc: Egbert Eich <eich@suse.de> Reviewed-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
-
Daniel Vetter authored
The usual pattern for our sub-function irq_handlers is that they check for the no-irq case themselves. This results in more streamlined code in the upper irq handlers. v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
Everywhere the same. Note that this patch leaves unnecessary braces behind, but the next patch will kill those all anyway (including the if itself) so I've figured I can keep the diff a bit smaller. v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
We already have a vfunc for this (and other parts of the hpd storm handling code already use it). v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
The combination of Paulo's fifo underrun detection code and Egbert's hpd storm handling code unfortunately made the hpd storm handling code racy. To avoid duplicating tricky interrupt locking code over all platforms start with a bit of refactoring. This patch is the very first step since in the end the irq storm handling code will handle all hotplug logic (and so also encapsulate the locking nicely). v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
By the time we write DEIER in the postinstall hook the interrupt handler could run any time. And it does modify DEIER to handle interrupts. Hence the DEIER read-modify-write cycle for enabling the PCU event source is racy. Close this races the same way we handle vblank interrupts: Unconditionally enable the interrupt in the IER register, but conditionally mask it in IMR. The later poses no such race since the interrupt handler does not touch DEIMR. Also update the comment, the clearing has already happened unconditionally above. v2: Actually shove the updated comment into the right train^W commit, as spotted by Paulo. Cc: Paulo Zanoni <przanoni@gmail.com> Reviewed-by:
-
Daniel Vetter authored
The haswell unclaimed register handling code forgot to take the spinlock. Since this is in the context of the non-rentrant interupt handler and we only have one interrupt handler it is sufficient to just grab the spinlock - we do not need to exclude any other interrupts from running on the same cpu. To prevent such gaffles in the future sprinkle assert_spin_locked over these functions. Unfornately this requires us to hold the spinlock in the ironlake postinstall hook where it is not strictly required: Currently that is run in single-threaded context and with userspace exlcuded from running concurrent ioctls. Add a comment explaining this. v2: ivb_can_enable_err_int also needs to be protected by the spinlock. To ensure this won't happen in the future again also sprinkle a spinlock assert in there. v3: Kill the 2nd call to ivb_can_enable_err_int I've accidentally left behind, spotted by Paulo. Cc: Paulo Zanoni <przanoni@gmail.com> Reviewed-by:
Paulo Zanoni <przanoni@gmail.com> Signed-off-by:
-
Ben Widawsky authored
With updates to the spec, we can actually see the context layout, and how many dwords are allocated. That table suggests we need 70720 bytes per HW context. Rounded up, this is 18 pages. Looking at what lives after the current 4 pages we use, I can't see too much important (mostly it's d3d related), but there are a couple of things which look scary. I am hopeful this can explain some of our odd HSW failures. v2: Make the context only 17 pages. The power context space isn't used ever, and execlists aren't used in our driver, making the actual total 66944 bytes. v3: Add a comment to the code. (Jesse & Paulo) Reported-by:
"Azad, Vinit" <vinit.azad@intel.com> Cc: stable@vger.kernel.org Reviewed-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
Ben Widawsky <ben@bwidawsk.net> Signed-off-by:
-
Ville Syrjälä authored
We forgot to add VLV_DISPLAY_BASE to the VLV sprite registers, which caused the sprites to not work at all. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Ville Syrjälä authored
The PIPECONF color range bit doesn't appear to be effective, on HDMI outputs at least. The color range bit in the port register works though, so let's use it. I have not yet verified whether the PIPECONF bit works on DP outputs. This reverts commit 83a2af88. Signed-off-by:
-
Ville Syrjälä authored
LPF is short for "low pass filter". Signed-off-by:
-
Ville Syrjälä authored
The current PLL settings produce a rather unstable picture when I hook up a VLV to my HP ZR24w display via a VGA cable. According to VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_9, we should use the the same LPF coefficients for DAC as we do for HDMI and RBR DP. And indeed that seems to cure the shivers. v2: Add the name of the relevant document to the commit message Signed-off-by:
-
Ville Syrjälä authored
If the current GPU frquency is below RPe, and we're asked to increase it, just go directly to RPe. This should provide better performance faster than letting the frequency trickle up in response to the up threshold interrupts. For now just do it for VLV, since that matches quite closely how VLV used to operate when the rps delayed timer kept things at RPe always. Signed-off-by:
-
Ville Syrjälä authored
There's little point in increasing the GPU frequency from the delayed rps work on VLV. Now when the GPU is idle, the GPU frequency actually keeps dropping gradually until it hits the minimum, whereas previously it just ping-ponged constantly between RPe and RPe-1. Signed-off-by:
-
Ville Syrjälä authored
I can't find GEN6_RP_INTERRUPT_LIMITS (0xA014) anywhere in VLV docs. Reading it always returns zero from what I can tell, and eliminating it doesn't seem to make any difference to the behaviour of the system. Signed-off-by:
-
Ville Syrjälä authored
Eliminate the weird inverted logic from the rps new_delay comparison. Signed-off-by:
-
Ville Syrjälä authored
It seems that even though Punit reports the frequency change to have been completed, it still reports the old frequency in the status register for some time. So rather than polling for Punit to complete the frequency change after each request, poll before. This gets rid of the spurious "Punit overrode GPU freq" messages. This also lets us continue working while Punit is performing the actual frequency change. As a result, openarena demo088-test1 timedemo average fps is increased by ~5 fps, and the slowest frame duration is reduced by ~25%. The sysfs cur_freq file always reads the current frequency from Punit anyway, so having rps.cur_delay be slightly off at times doesn't matter. Signed-off-by:
-
Ville Syrjälä authored
Always print both the MHz value and raw register value for rps stuff. Also kill a somewhat pointless local 'rpe' variable and just use dev_priv->rps.rpe_delay. While at it clean up the caps in "GPU" and "Punit" debug messages. Signed-off-by:
-
Chris Wilson authored
Report back the user error of attempting to setup a CRTC with an invalid framebuffer pitch. This is trickier than it should be as on gen4, there is a restriction that tiled surfaces must have a stride less than 16k - which is less than the largest supported CRTC size. v2: Fix the limits for gen3 v3: Move check into intel_framebuffer_init() and fix VLV limits. (vsyrjala) v4: Use idiomatic '>=' for generation checks References: https://bugs.freedesktop.org/show_bug.cgi?id=65099Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
-
Ville Syrjälä authored
No need to apply WaForceL3Serialization:vlv twice. Signed-off-by:
Damien Lespiau <damien.lespiau@intel.com> Signed-off-by:
-
Daniel Vetter authored
There are legit cases, e.g. when userspace asks for something impossible. So tune it down to debug output like we do with all other userspace-triggerable warnings. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66111#c5Reviewed-by:
-
Daniel Vetter authored
Bspec seems to be full of lies, at least it disagress with reality: Two systems corrobated that SDVO hpd bits are the same as on gen3. v2: Update comment a bit. Cc: Arthur Ranyan <arthur.j.runyan@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Tested-by:
Alex Fiestas <afiestas@kde.org> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405 Cc: stable@vger.kernel.org Acked-by:
-
Damien Lespiau authored
Follow the trend and don't code conditions with platforms but with features. Signed-off-by:
-
Jani Nikula authored
drivers/gpu/drm/i915/i915_gem.c: In function ‘i915_gem_object_bind_to_gtt’: drivers/gpu/drm/i915/i915_gem.c:3002:3: warning: format ‘%ld’ expects argument of type ‘long int’, but argument 5 has type ‘size_t’ [-Wformat] v2: Use %zu instead of %d. Two char patch, and 100% wrong. (Ville) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
-
Daniel Vetter authored
Nothing the user (nor we) really can do about this, but upsets a nice quiet boot. Note that this happens mostly on SDVs where OEMs obviously haven't had a chance yet to appropriately trim the output list. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65988Reviewed-by:
-
Konrad Rzeszutek Wilk authored
Git commit 90797e6d ("drm/i915: create compact dma scatter lists for gem objects") makes certain assumptions about the under laying DMA API that are not always correct. On a ThinkPad X230 with an Intel HD 4000 with Xen during the bootup I see: [drm:intel_pipe_set_base] *ERROR* pin & fence failed [drm:intel_crtc_set_config] *ERROR* failed to set mode on [CRTC:3], err = -28 Bit of debugging traced it down to dma_map_sg failing (in i915_gem_gtt_prepare_object) as some of the SG entries were huge (3MB). That unfortunately are sizes that the SWIOTLB is incapable of handling - the maximum it can handle is a an entry of 512KB of virtual contiguous memory for its bounce buffer. (See IO_TLB_SEGSIZE). Previous to the above mention git commit the SG entries were of 4KB, and the code introduced by above git commit squashed the CPU contiguous PFNs in one big virtual address provided to DMA API. This patch is a simple semi-revert - were we emulate the old behavior if we detect that SWIOTLB is online. If it is not online then we continue on with the new compact scatter gather mechanism. An alternative solution would be for the the '.get_pages' and the i915_gem_gtt_prepare_object to retry with smaller max gap of the amount of PFNs that can be combined together - but with this issue discovered during rc7 that might be too risky. Reported-and-Tested-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> CC: Chris Wilson <chris@chris-wilson.co.uk> CC: Imre Deak <imre.deak@intel.com> CC: Daniel Vetter <daniel.vetter@ffwll.ch> CC: David Airlie <airlied@linux.ie> CC: <dri-devel@lists.freedesktop.org> Signed-off-by:
-
Rui Guo authored
In some virtualized environments (e.g. XEN), there is irrelevant ISA bridge in the system. To work reliably, we should scan trhough all the ISA bridge devices and check for the first match, instead of only checking the first one. Signed-off-by:
Rui Guo <firemeteor@users.sourceforge.net> [danvet: Fixup conflict with the num_pch_pll removal. And add subsystem header to the commit message headline.] Signed-off-by:
-
Paulo Zanoni authored
Because it's the function that destroys the connector, not the encoder. And we already have intel_dp_encoder_destroy. This has annoyed me for a long time. Signed-off-by:
Zoltan Nyul <zoltan.nyul@intel.com> Signed-off-by:
-
- 28 Jun, 2013 11 commits
-
-
Paulo Zanoni authored
We've been ignoring this return value, so print a nice backtrace in case it's not what we expected. Signed-off-by:
-
Paulo Zanoni authored
Because calling intel_dp_encoder_destroy inside intel_edp_init_connector is just wrong. This is the initialization path, so we should properly unwind all the initialization through the whole caller stack. On the intel_dp_encoder_destroy function we do the following: 1 - Call i2c_del_adapter 2 - Call drm_encoder_cleanup 3 - If edp: 3.1 - Cancel panel_vdd_work 3.2 - Call ironlake_panel_vdd_of_sync 4 - Free the encoder And here is how we unwind each specific step: 1 - We have intel_dp_init_connector -> intel_dp_i2c_init -> i2c_dp_aux_add_bus -> i2c_add_adapter, so we call i2c_del_dapter at intel_dp_init_connector 2 - Call it in the same function that called drm_encoder_init 3 - Call it in the same function that called INIT_DELAYED_WORK 4 - Free it in the same function that allocated it Signed-off-by: -
Paulo Zanoni authored
Because calling intel_dp_destroy inside intel_edp_init_connector is just wrong. This is the initialization path, so we should properly unwind all the initialization through the whole caller stack. On the intel_dp_destroy function we do the following: 1 - Free edid if it exists 2 - Call intel_panel_fini in case it's eDP 3 - Call drm_sysfs_connector_remove 4 - Call drm_connector_cleanup 5 - Free the connector And here is how we unwind each specific step: 1 - No need as we still didn't assign anything 2 - No need as we still didn't call intel_panel_init 3 - Call it in the same function that called drm_sysfs_connector_add 4 - Call it in the same function that called drm_connector_init 5 - Free it in the same function that allocated it Signed-off-by:
-
Paulo Zanoni authored
In case we detect a "ghost eDP", intel_edp_init_connector frees both the connector and encoder and then returns. On Haswell, intel_ddi_init then tries to use the freed encoder on the HDMI initialization path since the following commit: commit 21a8e6a4 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Wed Apr 10 23:28:35 2013 +0200 drm/i915: don't setup hdmi for port D edp in ddi_init So now on intel_ddi_init we check for the "ghost eDP" case and return without trying to initialize HDMI. This way we won't try to read the freed "intel_encoder" struct in the next "if" statement. Signed-off-by:
-
Paulo Zanoni authored
Because intel_dp_init_connector is too big for my poor little brain. No functional changes. Signed-off-by:
-
Paulo Zanoni authored
By the time we call intel_dp_destroy (which destroys the connector) the encoder may have been destroyed already, so if we use it we may be reading some free memory. That happens in drm_mode_config_cleanup() and also inside intel_dp_init_connector() when we detect a ghost eDP. I also hope this may solve some random memory bugs. Reported by kmemcheck. Signed-off-by:
-
Dave Airlie authored
This reverts commit 160954b7. This was rearming the workqueue with a 0 timeout, causing a WARN_ON, and possible loop. Daniel writes: "I've looked a bit into this and I think we need to have a separate work struct for recovering these lost hotplug events since the continuous self-rearming case is a real risk (e.g. if a connector flip-flops all the time). At least I don't see a sane way to block out re-arming with the current code in a simple way. So reverting the offender seems like the right thing and I'll go back to the drawing board for 3.12." Signed-off-by:
Dave Airlie <airlied@redhat.com>
-
Laurent Pinchart authored
Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Laurent Pinchart authored
The i915 driver has been fixed not to modify the mode argument of the encoder mode_fixup operation. Remove the related comment from the documentation. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
-
Laurent Pinchart authored
Define the rules for using irqs from drm drivers. Signed-off-by:
-
YoungJun Cho authored
The dma_buf_fd() can return error when it fails to prepare fd, so the dma_buf needs to be put. Signed-off-by:
YoungJun Cho <yj44.cho@samsung.com> Signed-off-by:
Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
