__be32 is already a __bitwise type so we don't need the second __bitwise
here.  It causes a Sparse error:
include/scsi/osd_protocol.h:110:26: error: invalid modifier
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

We should unlock here before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Adds support for a new VIOS feature that allows ibmvfc to
optimize terminate_rport_io by telling the VIOS the target
is no longer accessible on the fabric and that it should
not send an ABTS out on the fabric to the device.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If attempting to abort requests due to a fail fail timeout
or error handling while the link is down, we cannot send
an abort out on the fabric. We can, however, send a cancel
to the VIOS. This fixes ibmvfc to send a cancel in this
case to prevent error handling from failing and/or
escalating.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Adds support for receiving FAST_IO_FAIL from fc_block_scsi_eh
when in error recovery. This fixes cases of devices being
taken offline when they are no longer accessible on the fabric,
preventing them from coming back online when the fabric recovers.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

The flags on a cancel operation are intended to indicate what,
if any, TMF will follow the cancel request. This fixes a case
where we were incorrectly setting the abort task set flag on
the cancel flag when we were cancelling an abort task set.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Command Window value from the CQE was used to calculate the
max_cmdsn for that session.The command window value extracted
for SKH-R adapter was not proper. The value was extracted from
BE adapter completion event. Fixed the issue by getting the
cmd_wnd value from SKH-R CQE.

The exp_cmdsn and max_cmdsn values were not converted to BE format
before calling the __iscsi_complete_pdu(). Fixed the issue of converting
to BE format.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

The driver creates "NAPI" context per core which is fine,
however the above routine declares the ret variable as static!
Thus there is only one instance of this variable!
When this routine is called from more than one thread of execution,
than the result is unpredictable.

         static unsigned int ret;
         .....

         ret = beiscsi_process_cq(pbe_eq);
                 <--------Another thread can enter here and change "ret".
         if (ret < budget) {
                ....
         }
                 <--------Another thread can enter here and change "ret".
         return ret;

Fix - remove the "static"
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Before tyring to establish a CXN with the target, check if the adapter is in
a stable state
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Number of CID assigned to a function from adapter can be dynamic. The CID count
for each function was fixed number before. Code Fix done so that adapters with
fixed/dynamic CID count will work with the driver.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

When target send a NOP-IN with valid TTT, driver issues a NOP-OUT
and the task was not freed from driver. The task list available for
the session used to run out, and as no more task list were available
no more iSCSI commands were exchanged on that session.
This patches fixed the issue, by calling iscsi_put_task.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Check the Logical Link status also as part of the port link status.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch fixes the displaying of number of active
sessions in use.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

The mgmt_hba_attributes structure declared was not proper and
because of that the FW response returned for the MBX_CMD was not
matching. This issue went unnoticed as mgmt_hba_attribs structure
members were never used in the code path.

This fix of displaying the FW version had to change the mgmt_hba_attrib
structure also. The latest driver will also work with the older FW as
the issue was in the driver declaration.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fix support for DEFQ extension which will be used by latest
adapters
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fixed the code flow based on the MACRO defined to check for
adapter.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Free CXN specific resource held by driver when login redirection
or connection retry happens. Login redirection was failing
because WRB/SGL were not allocated from the CID on which
doorbell was rung.

Fixed the issue raised by MikeC
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch limits the max number of msix vectors to 32.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

- Check Ready Bit before posting the BMBX Hi Address
- Fix the parameters passed to beiscsi_mccq_compl
  in beiscsi_open_conn()
- Fix tag value check in beiscsi_ep_connect.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

When MBX command fails with insufficent buffer, check for the
response lenght returned. Return success if response length
is non-zero value which indicates valid data.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch sends uninitialize pattern to FW during driver unload
which is expected by FW for cleanup
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

We need to store PROTO_ERR_IMPL_LOGO (26) things here, but the
first element isn't used so the array should have 27 elements.
This matches fwevt_to_rnevt[] which has 27 elements.

The patch solves a Smatch static checker warning on my system:
drivers/scsi/csiostor/csio_rnode.c:880 csio_rnode_fwevt_handler()
	error: buffer overflow '(rn)->stats.n_evt_fw' 26 <= 26
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

When IO is successfully completed while an abort is pending, eh_abort
incorrectly assumes that abort failed and performes recovery by issuing
cleanup. Howerver, cleanup timesout as the firmware has no clue about
this IO. Fix this by checking if the IO has already completed.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[jejb: move PCI_DEVICE_ID definitions to include/pci_ids.h]
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Set perf_config to 3 during firmware initialization to enable both
cached connections as well as cached tasks.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Brian Uchino <buchino@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If switch configured in FIP and adapter configured in non-fip mode, driver
panics while queueing FIP frame in non-existing fip_frame_queue. Added config
check before queueing FIP frame in misconfiguration case to avoid kernel panic.
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

FIP VLAN discovery discovers the FCoE VLAN that will be used by all other FIP
protocols as well as by the FCoE encapsulation for Fibre Channel payloads on
the established virtual link. One of the goals of FC-BB-5 was to be as
nonintrusive as possible on initiators and targets, and therefore FIP VLAN
discovery occurs in the native VLAN used by the initiator or target to
exchange Ethernet traffic. The FIP VLAN discovery protocol is the only FIP
protocol running on the native VLAN; all other FIP protocols run on the
discovered FCoE VLANs.

If an administrator has manually configured FCoE VLANs on ENodes and FCFs,
there is no need to use this protocol. FIP and FCoE will run over the
configured VLANs.

An ENode without FCoE VLANs configuration would use this automated discovery
protocol to discover over which VLANs FCoE is running.

The ENode sends a FIP VLAN discovery request to a multicast MAC address called
All-FCF-MACs, which is a multicast MAC address to which all FCFs listen.

All FCFs that can be reached in the native VLAN of the ENode are expected to
respond on the same VLAN with a response that lists one or more FCoE VLANs
that are available for the ENode's VN_Port login. This protocol has the sole
purpose of allowing the ENode to discover all the available FCoE VLANs.

Now the ENode may enable a subset of these VLANs for FCoE Running the FIP
protocol in these VLANs on a per VLAN basis. And FCoE data transactions also
would occur on this VLAN. Hence, Except for FIP VLAN discovery, all other FIP
and FCoE traffic runs on the selected FCoE VLAN.  Its only the FIP VLAN
Discovery protocol that is permitted to run on the Default native VLAN of the
system.

[**** NOTE ****]
We are working on moving this feature definitions and functionality to libfcoe
module. We need this patch to be approved, as Suse is looking forward to merge
this feature in SLES 11 SP3 release.  Once this patch is approved, we will
submit patch which should move vlan discovery feature to libfoce.

[Fengguang Wu <fengguang.wu@intel.com>: kmalloc cast removal]
Signed-off-by: Anantha Prakash T <atungara@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Pull networking updates from David Miller:
 "Highlights (1721 non-merge commits, this has to be a record of some
  sort):

   1) Add 'random' mode to team driver, from Jiri Pirko and Eric
      Dumazet.

   2) Make it so that any driver that supports configuration of multiple
      MAC addresses can provide the forwarding database add and del
      calls by providing a default implementation and hooking that up if
      the driver doesn't have an explicit set of handlers.  From Vlad
      Yasevich.

   3) Support GSO segmentation over tunnels and other encapsulating
      devices such as VXLAN, from Pravin B Shelar.

   4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.

   5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
      Dukkipati.

   6) In the PHY layer, allow supporting wake-on-lan in situations where
      the PHY registers have to be written for it to be configured.

      Use it to support wake-on-lan in mv643xx_eth.

      From Michael Stapelberg.

   7) Significantly improve firewire IPV6 support, from YOSHIFUJI
      Hideaki.

   8) Allow multiple packets to be sent in a single transmission using
      network coding in batman-adv, from Martin Hundebøll.

   9) Add support for T5 cxgb4 chips, from Santosh Rastapur.

  10) Generalize the VXLAN forwarding tables so that there is more
      flexibility in configurating various aspects of the endpoints.
      From David Stevens.

  11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
      from Dmitry Kravkov.

  12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
      Neira Ayuso.

  13) Start adding networking selftests.

  14) In situations of overload on the same AF_PACKET fanout socket, or
      per-cpu packet receive queue, minimize drop by distributing the
      load to other cpus/fanouts.  From Willem de Bruijn and Eric
      Dumazet.

  15) Add support for new payload offset BPF instruction, from Daniel
      Borkmann.

  16) Convert several drivers over to mdoule_platform_driver(), from
      Sachin Kamat.

  17) Provide a minimal BPF JIT image disassembler userspace tool, from
      Daniel Borkmann.

  18) Rewrite F-RTO implementation in TCP to match the final
      specification of it in RFC4138 and RFC5682.  From Yuchung Cheng.

  19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
      you like netlink, so I implemented netlink dumping of netlink
      sockets.") From Andrey Vagin.

  20) Remove ugly passing of rtnetlink attributes into rtnl_doit
      functions, from Thomas Graf.

  21) Allow userspace to be able to see if a configuration change occurs
      in the middle of an address or device list dump, from Nicolas
      Dichtel.

  22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
      Frederic Sowa.

  23) Increase accuracy of packet length used by packet scheduler, from
      Jason Wang.

  24) Beginning set of changes to make ipv4/ipv6 fragment handling more
      scalable and less susceptible to overload and locking contention,
      from Jesper Dangaard Brouer.

  25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
      instead.  From Hong Zhiguo.

  26) Optimize route usage in IPVS by avoiding reference counting where
      possible, from Julian Anastasov.

  27) Convert IPVS schedulers to RCU, also from Julian Anastasov.

  28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
      Eitzenberger.

  29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
      nfnetlink_log, and nfnetlink_queue.  From Gao feng.

  30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.

  31) Support several new r8169 chips, from Hayes Wang.

  32) Support tokenized interface identifiers in ipv6, from Daniel
      Borkmann.

  33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.

  34) Add 802.1ad vlan offload support, from Patrick McHardy.

  35) Support mmap() based netlink communication, also from Patrick
      McHardy.

  36) Support HW timestamping in mlx4 driver, from Amir Vadai.

  37) Rationalize AF_PACKET packet timestamping when transmitting, from
      Willem de Bruijn and Daniel Borkmann.

  38) Bring parity to what's provided by /proc/net/packet socket dumping
      and the info provided by netlink socket dumping of AF_PACKET
      sockets.  From Nicolas Dichtel.

  39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
      Poirier"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
  filter: fix va_list build error
  af_unix: fix a fatal race with bit fields
  bnx2x: Prevent memory leak when cnic is absent
  bnx2x: correct reading of speed capabilities
  net: sctp: attribute printl with __printf for gcc fmt checks
  netlink: kconfig: move mmap i/o into netlink kconfig
  netpoll: convert mutex into a semaphore
  netlink: Fix skb ref counting.
  net_sched: act_ipt forward compat with xtables
  mlx4_en: fix a build error on 32bit arches
  Revert "bnx2x: allow nvram test to run when device is down"
  bridge: avoid OOPS if root port not found
  drivers: net: cpsw: fix kernel warn on cpsw irq enable
  sh_eth: use random MAC address if no valid one supplied
  3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
  tg3: fix to append hardware time stamping flags
  unix/stream: fix peeking with an offset larger than data in queue
  unix/dgram: fix peeking with an offset larger than data in queue
  unix/dgram: peek beyond 0-sized skbs
  openvswitch: Remove unneeded ovs_netdev_get_ifindex()
  ...

This patch fixes the following build error.

In file included from include/linux/filter.h:52:0,
                 from arch/arm/net/bpf_jit_32.c:14:
include/linux/printk.h:54:2: error: unknown type name ‘va_list’
include/linux/printk.h:105:21: error: unknown type name ‘va_list’
include/linux/printk.h:108:30: error: unknown type name ‘va_list’
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull input updates from Dmitry Torokhov:
 "Assorted fixes and cleanups to the existing drivers plus a new driver
  for IMS Passenger Control Unit device they use for ther in-flight
  entertainment system."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits)
  Input: trackpoint - Optimize trackpoint init to use power-on reset
  Input: apbps2 - convert to devm_ioremap_resource()
  Input: ALPS - use %ph to print buffers
  ARM - shmobile: Armadillo800EVA: Move st1232 reset pin handling
  Input: st1232 - add reset pin handling
  Input: st1232 - convert to devm_* infrastructure
  Input: MT - handle semi-mt devices in core
  Input: adxl34x - use spi_get_drvdata()
  Input: ad7877 - use spi_get_drvdata() and spi_set_drvdata()
  Input: ads7846 - use spi_get_drvdata() and spi_set_drvdata()
  Input: ims-pcu - fix a memory leak on error
  Input: sysrq - supplement reset sequence with timeout functionality
  Input: tegra-kbc - support for defining row/columns based on SoC
  Input: imx_keypad - switch to using managed resources
  Input: arc_ps2 - add support for device tree
  Input: mma8450 - fix signed 12bits to 32bits conversion
  Input: eeti_ts - remove redundant null check
  Input: edt-ft5x06 - remove redundant null check before kfree
  Input: ad714x - add CONFIG_PM_SLEEP to suspend/resume functions
  Input: adxl34x - add CONFIG_PM_SLEEP to suspend/resume functions
  ...

Using bit fields is dangerous on ppc64/sparc64, as the compiler [1]
uses 64bit instructions to manipulate them.
If the 64bit word includes any atomic_t or spinlock_t, we can lose
critical concurrent changes.

This is happening in af_unix, where unix_sk(sk)->gc_candidate/
gc_maybe_cycle/lock share the same 64bit word.

This leads to fatal deadlock, as one/several cpus spin forever
on a spinlock that will never be available again.

A safer way would be to use a long to store flags.
This way we are sure compiler/arch wont do bad things.

As we own unix_gc_lock spinlock when clearing or setting bits,
we can use the non atomic __set_bit()/__clear_bit().

recursion_level can share the same 64bit location with the spinlock,
as it is set only with this spinlock held.

[1] bug fixed in gcc-4.8.0 :
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52080Reported-by: Ambrose Feinstein <ambrose@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
This fixes 2 small bugs - one which may cause an unnecessary link flap,
and the other is a small memory leak when unloading while cnic is not
loaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x driver allocates searcher T2 tables, but it releases that memory
during unload only released if the cnic is loaded.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the bnx2x driver reads the port configuration - mask irrelevant bits.

Without this change, the unintended bits may cause the driver to needlessly
toggle the link, as a comparison in the link flap avoidance flow will show
that the old link did not advertise the same capabilities and thus cannot
be retained.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>