Currently BUG() uses .word or .hword to create the necessary illegal
instructions. However if we are building BE8 then these get swapped
by the linker into different illegal instructions in the text. This
means that the BUG() macro does not get trapped properly.

Change to using <asm/opcodes.h> to provide the necessary ARM instruction
building as we cannot rely on gcc/gas having the `.inst` instructions
which where added to try and resolve this issue (reported by Dave Martin
<Dave.Martin@arm.com>).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>

Use <asm/opcodes.h> to correctly transform instruction byte ordering
into in-memory ordering.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>

The <hardware/coresight.h> needs to take into account the endian-ness
of the processor when reading and writing data, so change to using
the readl/writel relaxed variants from the raw ones.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

To avoid having to make every text section swap the instruction order
of all instructions, make sure modules are built also built with --be8
(as is the current kernel final link).

If we do not do this, we would end up having to swap all instructions
when loading a module, instead of just the instructions that we are
applying ELF relocations to.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>

When in BE8 mode, our instructions are not in the same ordering as the
data, so use <asm/opcodes.h> to take this into account.

Note, also requires modules to be built --be8
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>

The trap handler needs to take into account the endian configuration of
the system when loading instructions. Use <asm/opcodes.h> to provide the
necessary conversion functions.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

If we are in BE8 mode, we must deal with the instruction stream being
in LE order when data is being loaded in BE order. Ensure the data is
swapped before processing to avoid thre following:

Change to using <asm/opcodes.h> to provide the necessary conversion
functions to change the byte ordering.

This stops the following warning messages from the kernel on a fault:

Unhandled fault: alignment exception (0x001) at 0xbfa09567
Alignment trap: not handling instruction 030091e8 at [<80333e8c>]
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

Add support for the versatile express systems to boot big-endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

Add indication we can run these cores in BE mode, and ensure that the
secondary CPU is set to big-endian mode in the initialisation code as
the initial code runs little-endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>

Apart from a xgmac driver issue, the highbank seems to work correctly in
big-endian mode. Allow the selection of big-endian in the system.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Rob Herring <rob.herring@calxeda.com>

The smp_scu driver needs to use the relaxed readl/write accessors
to avoid any issues with the endian mode the processor core is in.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

Ensure the twd driver uses the correct calls to access the hardware
to ensure that we do not end up with data in the wrong endian format.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

The PL01X debug code needs to take into account which endian mode the
processor is running in. If it is big-endian, ensure the data is swapped
appropriately.

Note, we could do this slightly more efficiently if we have an macro to
do the necessary swap for the bits used by test.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

If we are booting in LE and compiled for BE8, then add code to
set the state to bE8. Since the instruction stream is always LE,
we do not need to do anything special to the instruction.

Also ensure that the secondary processors are started in the same mode.

Note, we do add about 20 bytes to the kernel image, but it seems easier
to do this than adding another configuration to change.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

The fixup_pv_table assumes that the instructions are in the same
endian configuration as the data, but when the CPU is running in
BE8 the instructions stay in little-endian format.

Make sure if CONFIG_CPU_ENDIAN_BE8 is set that we do all the
alterations to the instructions taking in to account the LDR/STR
will be swapping the data endian-ness.

Since the code is only modifying a byte, we avoid dual-swapping
the data, and just change the bits we clear and ORR in (in the
case where the code is not thumb2).

For thumb2, we add the necessary rev16 instructions to ensure that
the instructions are processed in the correct format, as it was
easier than re-writing the code to contain a mask and shift.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

Add ARM_BE8() helper to wrap any code conditional on being
compile when CONFIG_ARM_ENDIAN_BE8 is selected and convert
existing places where this is to use it.
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

The Kconfig for arch/arm/mach-ixp4xx has a local definition
of ARCH_SUPPORTS_BIG_ENDIAN which could be used elsewhere.
This means that if IXP4xx is selected and this symbol is
selected eleswhere then an warning is produced.

Clean the following error up by making the symbol be
selected by the main ARCH_IXP4XX definition and have a
common definition in arch/arm/mm/Kconfig

warning: (ARCH_xxx) selects ARCH_SUPPORTS_BIG_ENDIAN which has unmet direct dependencies (ARCH_IXP4XX)
warning: (ARCH_xxx) selects ARCH_SUPPORTS_BIG_ENDIAN which has unmet direct dependencies (ARCH_IXP4XX)
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

Modify the code to use current_euid(), and in_egroup_p, as in done
in fs/proc/proc_sysctl.c:test_perm()

Cc: stable@vger.kernel.org
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reported-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the outstanding target fixes queued up for v3.12-rc4 code.

  The highlights include:

   - Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
   - Allow sess_cmd_map allocation failure fallback to use vzalloc
   - Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
   - Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
     zero scsi_status bug
   - Make iscsi-target do acknowledgement tag release from RX context
   - Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags

  Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
  legacy wait_for_task=true release during fast-past StatSN
  acknowledgement, and two other SRP target related patches that address
  long-standing issues that are CC'ed for v3.3+.

  Extra thanks to Thomas Glanzmann for his testing feedback with
  COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
  iscsi-target: Perform release of acknowledged tags from RX context
  iscsi-target: Only perform wait_for_tasks when performing shutdown
  target: Fail on non zero scsi_status in compare_and_write_callback
  target: Fix recursive COMPARE_AND_WRITE callback failure
  target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
  ib_srpt: always set response for task management
  target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
  vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
  ib_srpt: Destroy cm_id before destroying QP.
  target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02

Pull slave-dmaengine fixes from Vinod Koul:
 "Here is the slave dmanegine fixes.  We have the fix for deadlock issue
  on imx-dma by Michael and Josh's edma config fix along with author
  change"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: imx-dma: fix callback path in tasklet
  dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
  dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
  dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
  edma: Update author email address

Pull btrfs fixes from Chris Mason:
 "This is a small collection of fixes, including a regression fix from
  Liu Bo that solves rare crashes with compression on.

  I've merged my for-linus up to 3.12-rc3 because the top commit is only
  meant for 3.12.  The rest of the fixes are also available in my master
  branch on top of my last 3.11 based pull"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: Fix crash due to not allocating integrity data for a bioset
  Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
  Btrfs: eliminate races in worker stopping code
  Btrfs: fix crash of compressed writes
  Btrfs: fix transid verify errors when recovering log tree

Pull GPIO fixes from Linus Walleij:
 "Two patches for the OMAP driver, dealing with setting up IRQs properly
  on the device tree boot path"

* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio/omap: auto-setup a GPIO when used as an IRQ
  gpio/omap: maintain GPIO and IRQ usage separately

Pull USB fixes from Greg KH:
 "Here are none fixes for various USB driver problems.  The majority are
  gadget/musb fixes, but there are some new device ids in here as well"

* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: add Intel Clovertrail pci id
  usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
  usb: gadget: f_fs: fix error handling
  usb: musb: dsps: do not bind to "musb-hdrc"
  USB: serial: option: Ignore card reader interface on Huawei E1750
  usb: musb: gadget: fix otg active status flag
  usb: phy: gpio-vbus: fix deferred probe from __init
  usb: gadget: pxa25x_udc: fix deferred probe from __init
  usb: musb: fix otg default state

Pull tty fixes from Greg KH:
 "Here are two tty driver fixes for 3.12-rc4.

  One fixes the reported regression in the n_tty code that a number of
  people found recently, and the other one fixes an issue with xen
  consoles that broke in 3.10"

* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  xen/hvc: allow xenboot console to be used again
  tty: Fix pty master read() after slave closes

Pull staging fixes from Greg KH:
 "Here are 4 tiny staging and iio driver fixes for 3.12-rc4.  Nothing
  major, just some small fixes for reported issues"

* tag 'staging-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
  iio:magnetometer: Bugfix magnetometer default output registers
  iio: Remove debugfs entries in iio_device_unregister()
  iio: amplifiers: ad8366: Remove regulator_put

When btrfs creates a bioset, we must also allocate the integrity data pool.
Otherwise btrfs will crash when it tries to submit a bio to a checksumming
disk:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
 IP: [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
 PGD 2305e4067 PUD 23063d067 PMD 0
 Oops: 0000 [#1] PREEMPT SMP
 Modules linked in: btrfs scsi_debug xfs ext4 jbd2 ext3 jbd mbcache
sch_fq_codel eeprom lpc_ich mfd_core nfsd exportfs auth_rpcgss af_packet
raid6_pq xor zlib_deflate libcrc32c [last unloaded: scsi_debug]
 CPU: 1 PID: 4486 Comm: mount Not tainted 3.12.0-rc1-mcsum #2
 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
 task: ffff8802451c9720 ti: ffff880230698000 task.ti: ffff880230698000
 RIP: 0010:[<ffffffff8111e28a>]  [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
 RSP: 0018:ffff880230699688  EFLAGS: 00010286
 RAX: 0000000000000001 RBX: 0000000000000000 RCX: 00000000005f8445
 RDX: 0000000000000001 RSI: 0000000000000010 RDI: 0000000000000000
 RBP: ffff8802306996f8 R08: 0000000000011200 R09: 0000000000000008
 R10: 0000000000000020 R11: ffff88009d6e8000 R12: 0000000000011210
 R13: 0000000000000030 R14: ffff8802306996b8 R15: ffff8802451c9720
 FS:  00007f25b8a16800(0000) GS:ffff88024fc80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: 0000000000000018 CR3: 0000000230576000 CR4: 00000000000007e0
 Stack:
  ffff8802451c9720 0000000000000002 ffffffff81a97100 0000000000281250
  ffffffff81a96480 ffff88024fc99150 ffff880228d18200 0000000000000000
  0000000000000000 0000000000000040 ffff880230e8c2e8 ffff8802459dc900
 Call Trace:
  [<ffffffff811b2208>] bio_integrity_alloc+0x48/0x1b0
  [<ffffffff811b26fc>] bio_integrity_prep+0xac/0x360
  [<ffffffff8111e298>] ? mempool_alloc+0x58/0x150
  [<ffffffffa03e8041>] ? alloc_extent_state+0x31/0x110 [btrfs]
  [<ffffffff81241579>] blk_queue_bio+0x1c9/0x460
  [<ffffffff8123e58a>] generic_make_request+0xca/0x100
  [<ffffffff8123e639>] submit_bio+0x79/0x160
  [<ffffffffa03f865e>] btrfs_map_bio+0x48e/0x5b0 [btrfs]
  [<ffffffffa03c821a>] btree_submit_bio_hook+0xda/0x110 [btrfs]
  [<ffffffffa03e7eba>] submit_one_bio+0x6a/0xa0 [btrfs]
  [<ffffffffa03ef450>] read_extent_buffer_pages+0x250/0x310 [btrfs]
  [<ffffffff8125eef6>] ? __radix_tree_preload+0x66/0xf0
  [<ffffffff8125f1c5>] ? radix_tree_insert+0x95/0x260
  [<ffffffffa03c66f6>] btree_read_extent_buffer_pages.constprop.128+0xb6/0x120
[btrfs]
  [<ffffffffa03c8c1a>] read_tree_block+0x3a/0x60 [btrfs]
  [<ffffffffa03caefd>] open_ctree+0x139d/0x2030 [btrfs]
  [<ffffffffa03a282a>] btrfs_mount+0x53a/0x7d0 [btrfs]
  [<ffffffff8113ab0b>] ? pcpu_alloc+0x8eb/0x9f0
  [<ffffffff81167305>] ? __kmalloc_track_caller+0x35/0x1e0
  [<ffffffff81176ba0>] mount_fs+0x20/0xd0
  [<ffffffff81191096>] vfs_kern_mount+0x76/0x120
  [<ffffffff81193320>] do_mount+0x200/0xa40
  [<ffffffff81135cdb>] ? strndup_user+0x5b/0x80
  [<ffffffff81193bf0>] SyS_mount+0x90/0xe0
  [<ffffffff8156d31d>] system_call_fastpath+0x1a/0x1f
 Code: 4c 8d 75 a8 4c 89 6d e8 45 89 e0 4c 8d 6f 30 48 89 5d d8 41 83 e0 af 48
89 fb 49 83 c6 18 4c 89 7d f8 65 4c 8b 3c 25 c0 b8 00 00 <48> 8b 73 18 44 89 c7
44 89 45 98 ff 53 20 48 85 c0 48 89 c2 74
 RIP  [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
  RSP <ffff880230699688>
 CR2: 0000000000000018
 ---[ end trace 7a96042017ed21e2 ]---
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

Pull CIFS fixes from Steve French:
 "Small set of cifs fixes.  Most important is Jeff's fix that works
  around disconnection problems which can be caused by simultaneous use
  of user space tools (starting a long running smbclient backup then
  doing a cifs kernel mount) or multiple cifs mounts through a NAT, and
  Jim's fix to deal with reexport of cifs share.

  I expect to send two more cifs fixes next week (being tested now) -
  fixes to address an SMB2 unmount hang when server dies and a fix for
  cifs symlink handling of Windows "NFS" symlinks"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  [CIFS] update cifs.ko version
  [CIFS] Remove ext2 flags that have been moved to fs.h
  [CIFS] Provide sane values for nlink
  cifs: stop trying to use virtual circuits
  CIFS: FS-Cache: Uncache unread pages in cifs_readpages() before freeing them

Pull PCI fix from Bjorn Helgaas:
 "We merged what was intended to be an MMCONFIG cleanup, but in fact,
  for systems without _CBA (which is almost everything), it broke
  extended config space for domain 0 and it broke all config space for
  other domains.

  This reverts the change"

* tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"

This reverts commit 07f9b61c.

07f9b61c was intended to be a cleanup that didn't change anything, but in
fact, for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and all config space for other domains.

Reference: http://lkml.kernel.org/r/20131004011806.GE20450@dangermouse.emea.sgi.comReported-by: Hedi Berriche <hedi@sgi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Pull ACPI and power management fixes from Rafael Wysocki:

 - The resume part of user space driven hibernation (s2disk) is now
   broken after the change that moved the creation of memory bitmaps to
   after the freezing of tasks, because I forgot that the resume utility
   loaded the image before freezing tasks and needed the bitmaps for
   that.  The fix adds special handling for that case.

 - One of recent commits changed the export of acpi_bus_get_device() to
   EXPORT_SYMBOL_GPL(), which was technically correct but broke existing
   binary modules using that function including one in particularly
   widespread use.  Change it back to EXPORT_SYMBOL().

 - The intel_pstate driver sometimes fails to disable turbo if its
   no_turbo sysfs attribute is set.  Fix from Srinivas Pandruvada.

 - One of recent cpufreq fixes forgot to update a check in cpufreq-cpu0
   which still (incorrectly) treats non-NULL as non-error.  Fix from
   Philipp Zabel.

 - The SPEAr cpufreq driver uses a wrong variable type in one place
   preventing it from catching errors returned by one of the functions
   called by it.  Fix from Sachin Kamat.

* tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: Use EXPORT_SYMBOL() for acpi_bus_get_device()
  intel_pstate: fix no_turbo
  cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
  cpufreq: SPEAr: Fix incorrect variable type
  PM / hibernate: Fix user space driven resume regression

Pull xfs bugfixes from Ben Myers:
 "There are lockdep annotations for project quotas, a fix for dirent
  dtype support on v4 filesystems, a fix for a memory leak in recovery,
  and a fix for the build error that resulted from it.  D'oh"

* tag 'xfs-for-linus-v3.12-rc4' of git://oss.sgi.com/xfs/xfs:
  xfs: Use kmem_free() instead of free()
  xfs: fix memory leak in xlog_recover_add_to_trans
  xfs: dirent dtype presence is dependent on directory magic numbers
  xfs: lockdep needs to know about 3 dquot-deep nesting

Now avc_audit() has no more users with that parameter. Remove it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

.. so get rid of it.  The only indirect users were all the
avc_has_perm() callers which just expanded to have a zero flags
argument.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

free_device rcu callback, scheduled from btrfs_rm_dev_replace_srcdev,
can be processed before btrfs_scratch_superblock is called, which would
result in a use-after-free on btrfs_device contents.  Fix this by
zeroing the superblock before the rcu callback is registered.

Cc: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

The current implementation of worker threads in Btrfs has races in
worker stopping code, which cause all kinds of panics and lockups when
running btrfs/011 xfstest in a loop.  The problem is that
btrfs_stop_workers is unsynchronized with respect to check_idle_worker,
check_busy_worker and __btrfs_start_workers.

E.g., check_idle_worker race flow:

       btrfs_stop_workers():            check_idle_worker(aworker):
- grabs the lock
- splices the idle list into the
  working list
- removes the first worker from the
  working list
- releases the lock to wait for
  its kthread's completion
                                  - grabs the lock
                                  - if aworker is on the working list,
                                    moves aworker from the working list
                                    to the idle list
                                  - releases the lock
- grabs the lock
- puts the worker
- removes the second worker from the
  working list
                              ......
        btrfs_stop_workers returns, aworker is on the idle list
                 FS is umounted, memory is freed
                              ......
              aworker is waken up, fireworks ensue

With this applied, I wasn't able to trigger the problem in 48 hours,
whereas previously I could reliably reproduce at least one of these
races within an hour.
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

The crash[1] is found by xfstests/generic/208 with "-o compress",
it's not reproduced everytime, but it does panic.

The bug is quite interesting, it's actually introduced by a recent commit
(573aecaf,
Btrfs: actually limit the size of delalloc range).

Btrfs implements delay allocation, so during writeback, we
(1) get a page A and lock it
(2) search the state tree for delalloc bytes and lock all pages within the range
(3) process the delalloc range, including find disk space and create
    ordered extent and so on.
(4) submit the page A.

It runs well in normal cases, but if we're in a racy case, eg.
buffered compressed writes and aio-dio writes,
sometimes we may fail to lock all pages in the 'delalloc' range,
in which case, we need to fall back to search the state tree again with
a smaller range limit(max_bytes = PAGE_CACHE_SIZE - offset).

The mentioned commit has a side effect, that is, in the fallback case,
we can find delalloc bytes before the index of the page we already have locked,
so we're in the case of (delalloc_end <= *start) and return with (found > 0).

This ends with not locking delalloc pages but making ->writepage still
process them, and the crash happens.

This fixes it by just thinking that we find nothing and returning to caller
as the caller knows how to deal with it properly.

[1]:
------------[ cut here ]------------
kernel BUG at mm/page-writeback.c:2170!
[...]
CPU: 2 PID: 11755 Comm: btrfs-delalloc- Tainted: G           O 3.11.0+ #8
[...]
RIP: 0010:[<ffffffff810f5093>]  [<ffffffff810f5093>] clear_page_dirty_for_io+0x1e/0x83
[...]
[ 4934.248731] Stack:
[ 4934.248731]  ffff8801477e5dc8 ffffea00049b9f00 ffff8801869f9ce8 ffffffffa02b841a
[ 4934.248731]  0000000000000000 0000000000000000 0000000000000fff 0000000000000620
[ 4934.248731]  ffff88018db59c78 ffffea0005da8d40 ffffffffa02ff860 00000001810016c0
[ 4934.248731] Call Trace:
[ 4934.248731]  [<ffffffffa02b841a>] extent_range_clear_dirty_for_io+0xcf/0xf5 [btrfs]
[ 4934.248731]  [<ffffffffa02a8889>] compress_file_range+0x1dc/0x4cb [btrfs]
[ 4934.248731]  [<ffffffff8104f7af>] ? detach_if_pending+0x22/0x4b
[ 4934.248731]  [<ffffffffa02a8bad>] async_cow_start+0x35/0x53 [btrfs]
[ 4934.248731]  [<ffffffffa02c694b>] worker_loop+0x14b/0x48c [btrfs]
[ 4934.248731]  [<ffffffffa02c6800>] ? btrfs_queue_worker+0x25c/0x25c [btrfs]
[ 4934.248731]  [<ffffffff810608f5>] kthread+0x8d/0x95
[ 4934.248731]  [<ffffffff81060868>] ? kthread_freezable_should_stop+0x43/0x43
[ 4934.248731]  [<ffffffff814fe09c>] ret_from_fork+0x7c/0xb0
[ 4934.248731]  [<ffffffff81060868>] ? kthread_freezable_should_stop+0x43/0x43
[ 4934.248731] Code: ff 85 c0 0f 94 c0 0f b6 c0 59 5b 5d c3 0f 1f 44 00 00 55 48 89 e5 41 54 53 48 89 fb e8 2c de 00 00 49 89 c4 48 8b 03 a8 01 75 02 <0f> 0b 4d 85 e4 74 52 49 8b 84 24 80 00 00 00 f6 40 20 01 75 44
[ 4934.248731] RIP  [<ffffffff810f5093>] clear_page_dirty_for_io+0x1e/0x83
[ 4934.248731]  RSP <ffff8801869f9c48>
[ 4934.280307] ---[ end trace 36f06d3f8750236a ]---
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

If we crash with a log, remount and recover that log, and then crash before we
can commit another transaction we will get transid verify errors on the next
mount.  This is because we were not zero'ing out the log when we committed the
transaction after recovery.  This is ok as long as we commit another transaction
at some point in the future, but if you abort or something else goes wrong you
can end up in this weird state because the recovery stuff says that the tree log
should have a generation+1 of the super generation, which won't be the case of
the transaction that was started for recovery.  Fix this by removing the check
and _always_ zero out the log portion of the super when we commit a transaction.
This fixes the transid verify issues I was seeing with my force errors tests.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>

Every single user passes in '0'.  I think we had non-zero users back in
some stone age when selinux_inode_permission() was implemented in terms
of inode_has_perm(), but that complicated case got split up into a
totally separate code-path so that we could optimize the much simpler
special cases.

See commit 2e334057 ("SELinux: delay initialization of audit data in
selinux_inode_permission") for example.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>