- 16 Mar, 2023 9 commits
-
-
Vladimir Oltean authored
Currently, when dsa_slave_change_mtu() is called on a user port where dev->max_mtu is 1500 (as returned by ds->ops->port_max_mtu()), the code will stumble upon this check: if (new_master_mtu > mtu_limit) return -ERANGE; because new_master_mtu is adjusted for the tagger overhead but mtu_limit is not. But it would be good if the logic went through, for example if the DSA master really depends on an MTU adjustment to accept DSA-tagged frames. To make the code pass through the check, we need to adjust mtu_limit for the overhead as well, if the minimum restriction was caused by the DSA user port's MTU (dev->max_mtu). A DSA user port MTU and a DSA master MTU are always offset by the protocol overhead. Currently no drivers return 1500 .port_max_mtu(), but this is only temporary and a bug in itself - mv88e6xxx should have done that, but since commit b9c587fe ("dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports") it no longer does. This is a preparation for fixing that. Fixes: bfcb8132 ("net: dsa: configure the MTU for switch ports") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Maciej Fijalkowski authored
ice_qp_dis() intends to stop a given queue pair that is a target of xsk pool attach/detach. One of the steps is to disable interrupts on these queues. It currently is broken in a way that txq irq is turned off *after* HW flush which in turn takes no effect. ice_qp_dis(): -> ice_qvec_dis_irq() --> disable rxq irq --> flush hw -> ice_vsi_stop_tx_ring() -->disable txq irq Below splat can be triggered by following steps: - start xdpsock WITHOUT loading xdp prog - run xdp_rxq_info with XDP_TX action on this interface - start traffic - terminate xdpsock [ 256.312485] BUG: kernel NULL pointer dereference, address: 0000000000000018 [ 256.319560] #PF: supervisor read access in kernel mode [ 256.324775] #PF: error_code(0x0000) - not-present page [ 256.329994] PGD 0 P4D 0 [ 256.332574] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 256.337006] CPU: 3 PID: 32 Comm: ksoftirqd/3 Tainted: G OE 6.2.0-rc5+ #51 [ 256.345218] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [ 256.355807] RIP: 0010:ice_clean_rx_irq_zc+0x9c/0x7d0 [ice] [ 256.361423] Code: b7 8f 8a 00 00 00 66 39 ca 0f 84 f1 04 00 00 49 8b 47 40 4c 8b 24 d0 41 0f b7 45 04 66 25 ff 3f 66 89 04 24 0f 84 85 02 00 00 <49> 8b 44 24 18 0f b7 14 24 48 05 00 01 00 00 49 89 04 24 49 89 44 [ 256.380463] RSP: 0018:ffffc900088bfd20 EFLAGS: 00010206 [ 256.385765] RAX: 000000000000003c RBX: 0000000000000035 RCX: 000000000000067f [ 256.393012] RDX: 0000000000000775 RSI: 0000000000000000 RDI: ffff8881deb3ac80 [ 256.400256] RBP: 000000000000003c R08: ffff889847982710 R09: 0000000000010000 [ 256.407500] R10: ffffffff82c060c0 R11: 0000000000000004 R12: 0000000000000000 [ 256.414746] R13: ffff88811165eea0 R14: ffffc9000d255000 R15: ffff888119b37600 [ 256.421990] FS: 0000000000000000(0000) GS:ffff8897e0cc0000(0000) knlGS:0000000000000000 [ 256.430207] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 256.436036] CR2: 0000000000000018 CR3: 0000000005c0a006 CR4: 00000000007706e0 [ 256.443283] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 256.450527] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 256.457770] PKRU: 55555554 [ 256.460529] Call Trace: [ 256.463015] <TASK> [ 256.465157] ? ice_xmit_zc+0x6e/0x150 [ice] [ 256.469437] ice_napi_poll+0x46d/0x680 [ice] [ 256.473815] ? _raw_spin_unlock_irqrestore+0x1b/0x40 [ 256.478863] __napi_poll+0x29/0x160 [ 256.482409] net_rx_action+0x136/0x260 [ 256.486222] __do_softirq+0xe8/0x2e5 [ 256.489853] ? smpboot_thread_fn+0x2c/0x270 [ 256.494108] run_ksoftirqd+0x2a/0x50 [ 256.497747] smpboot_thread_fn+0x1c1/0x270 [ 256.501907] ? __pfx_smpboot_thread_fn+0x10/0x10 [ 256.506594] kthread+0xea/0x120 [ 256.509785] ? __pfx_kthread+0x10/0x10 [ 256.513597] ret_from_fork+0x29/0x50 [ 256.517238] </TASK> In fact, irqs were not disabled and napi managed to be scheduled and run while xsk_pool pointer was still valid, but SW ring of xdp_buff pointers was already freed. To fix this, call ice_qvec_dis_irq() after ice_vsi_stop_tx_ring(). Also while at it, remove redundant ice_clean_rx_ring() call - this is handled in ice_qp_clean_rings(). Fixes: 2d4238f5 ("ice: Add support for AF_XDP") Signed-off-by:
Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by:
Larysa Zaremba <larysa.zaremba@intel.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Acked-by:
John Fastabend <john.fastabend@gmail.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
-
David S. Miller authored
-
Arseniy Krasnov authored
This adds SOCK_STREAM and SOCK_SEQPACKET tests for invalid buffer case. It tries to read data to NULL buffer (data already presents in socket's queue), then uses valid buffer. For SOCK_STREAM second read must return data, because skbuff is not dropped, but for SOCK_SEQPACKET skbuff will be dropped by kernel, and 'recv()' will return EAGAIN. Signed-off-by:
Arseniy Krasnov <AVKrasnov@sberdevices.ru> Reviewed-by:
Stefano Garzarella <sgarzare@redhat.com> Signed-off-by:
-
Arseniy Krasnov authored
This returns behaviour of SOCK_STREAM read as before skbuff usage. When copying to user fails current skbuff won't be dropped, but returned to sockets's queue. Technically instead of 'skb_dequeue()', 'skb_peek()' is called and when skbuff becomes empty, it is removed from queue by '__skb_unlink()'. Fixes: 71dc9ec9 ("virtio/vsock: replace virtio_vsock_pkt with sk_buff") Signed-off-by:
Bobby Eshleman <bobby.eshleman@bytedance.com> Signed-off-by:
-
Arseniy Krasnov authored
Since we now no longer use 'skb->len' to update credit, there is no sense to update skbuff state, because it is used only once after dequeue to copy data and then will be released. Fixes: 71dc9ec9 ("virtio/vsock: replace virtio_vsock_pkt with sk_buff") Signed-off-by:
-
Arseniy Krasnov authored
'skb->len' can vary when we partially read the data, this complicates the calculation of credit to be updated in 'virtio_transport_inc_rx_pkt()/ virtio_transport_dec_rx_pkt()'. Also in 'virtio_transport_dec_rx_pkt()' we were miscalculating the credit since 'skb->len' was redundant. For these reasons, let's replace the use of skbuff state to calculate new 'rx_bytes'/'fwd_cnt' values with explicit value as input argument. This makes code more simple, because it is not needed to change skbuff state before each call to update 'rx_bytes'/'fwd_cnt'. Fixes: 71dc9ec9 ("virtio/vsock: replace virtio_vsock_pkt with sk_buff") Signed-off-by:
-
Vladimir Oltean authored
Since the blamed commit, phy_ethtool_get_wol() and phy_ethtool_set_wol() acquire phydev->lock, but the mscc phy driver implementations, vsc85xx_wol_get() and vsc85xx_wol_set(), acquire the same lock as well, resulting in a deadlock. $ ip link set swp3 down ============================================ WARNING: possible recursive locking detected mscc_felix 0000:00:00.5 swp3: Link is Down -------------------------------------------- ip/375 is trying to acquire lock: ffff3d7e82e987a8 (&dev->lock){+.+.}-{4:4}, at: vsc85xx_wol_get+0x2c/0xf4 but task is already holding lock: ffff3d7e82e987a8 (&dev->lock){+.+.}-{4:4}, at: phy_ethtool_get_wol+0x3c/0x6c other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&dev->lock); lock(&dev->lock); *** DEADLOCK *** May be due to missing lock nesting notation 2 locks held by ip/375: #0: ffffd43b2a955788 (rtnl_mutex){+.+.}-{4:4}, at: rtnetlink_rcv_msg+0x144/0x58c #1: ffff3d7e82e987a8 (&dev->lock){+.+.}-{4:4}, at: phy_ethtool_get_wol+0x3c/0x6c Call trace: __mutex_lock+0x98/0x454 mutex_lock_nested+0x2c/0x38 vsc85xx_wol_get+0x2c/0xf4 phy_ethtool_get_wol+0x50/0x6c phy_suspend+0x84/0xcc phy_state_machine+0x1b8/0x27c phy_stop+0x70/0x154 phylink_stop+0x34/0xc0 dsa_port_disable_rt+0x2c/0xa4 dsa_slave_close+0x38/0xec __dev_close_many+0xc8/0x16c __dev_change_flags+0xdc/0x218 dev_change_flags+0x24/0x6c do_setlink+0x234/0xea4 __rtnl_newlink+0x46c/0x878 rtnl_newlink+0x50/0x7c rtnetlink_rcv_msg+0x16c/0x58c Removing the mutex_lock(&phydev->lock) calls from the driver restores the functionality. Fixes: 2f987d48 ("net: phy: Add locks to ethtool functions") Signed-off-by:Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230314153025.2372970-1-vladimir.oltean@nxp.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Shawn Bohrer authored
Commit 718a18a0 ("veth: Rework veth_xdp_rcv_skb in order to accept non-linear skb") introduced a bug where it tried to use pskb_expand_head() if the headroom was less than XDP_PACKET_HEADROOM. This however uses kmalloc to expand the head, which will later allow consume_skb() to free the skb while is it still in use by AF_XDP. Previously if the headroom was less than XDP_PACKET_HEADROOM we continued on to allocate a new skb from pages so this restores that behavior. BUG: KASAN: use-after-free in __xsk_rcv+0x18d/0x2c0 Read of size 78 at addr ffff888976250154 by task napi/iconduit-g/148640 CPU: 5 PID: 148640 Comm: napi/iconduit-g Kdump: loaded Tainted: G O 6.1.4-cloudflare-kasan-2023.1.2 #1 Hardware name: Quanta Computer Inc. QuantaPlex T41S-2U/S2S-MB, BIOS S2S_3B10.03 06/21/2018 Call Trace: <TASK> dump_stack_lvl+0x34/0x48 print_report+0x170/0x473 ? __xsk_rcv+0x18d/0x2c0 kasan_report+0xad/0x130 ? __xsk_rcv+0x18d/0x2c0 kasan_check_range+0x149/0x1a0 memcpy+0x20/0x60 __xsk_rcv+0x18d/0x2c0 __xsk_map_redirect+0x1f3/0x490 ? veth_xdp_rcv_skb+0x89c/0x1ba0 [veth] xdp_do_redirect+0x5ca/0xd60 veth_xdp_rcv_skb+0x935/0x1ba0 [veth] ? __netif_receive_skb_list_core+0x671/0x920 ? veth_xdp+0x670/0x670 [veth] veth_xdp_rcv+0x304/0xa20 [veth] ? do_xdp_generic+0x150/0x150 ? veth_xdp_rcv_one+0xde0/0xde0 [veth] ? _raw_spin_lock_bh+0xe0/0xe0 ? newidle_balance+0x887/0xe30 ? __perf_event_task_sched_in+0xdb/0x800 veth_poll+0x139/0x571 [veth] ? veth_xdp_rcv+0xa20/0xa20 [veth] ? _raw_spin_unlock+0x39/0x70 ? finish_task_switch.isra.0+0x17e/0x7d0 ? __switch_to+0x5cf/0x1070 ? __schedule+0x95b/0x2640 ? io_schedule_timeout+0x160/0x160 __napi_poll+0xa1/0x440 napi_threaded_poll+0x3d1/0x460 ? __napi_poll+0x440/0x440 ? __kthread_parkme+0xc6/0x1f0 ? __napi_poll+0x440/0x440 kthread+0x2a2/0x340 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x22/0x30 </TASK> Freed by task 148640: kasan_save_stack+0x23/0x50 kasan_set_track+0x21/0x30 kasan_save_free_info+0x2a/0x40 ____kasan_slab_free+0x169/0x1d0 slab_free_freelist_hook+0xd2/0x190 __kmem_cache_free+0x1a1/0x2f0 skb_release_data+0x449/0x600 consume_skb+0x9f/0x1c0 veth_xdp_rcv_skb+0x89c/0x1ba0 [veth] veth_xdp_rcv+0x304/0xa20 [veth] veth_poll+0x139/0x571 [veth] __napi_poll+0xa1/0x440 napi_threaded_poll+0x3d1/0x460 kthread+0x2a2/0x340 ret_from_fork+0x22/0x30 The buggy address belongs to the object at ffff888976250000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 340 bytes inside of 2048-byte region [ffff888976250000, ffff888976250800) The buggy address belongs to the physical page: page:00000000ae18262a refcount:2 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x976250 head:00000000ae18262a order:3 compound_mapcount:0 compound_pincount:0 flags: 0x2ffff800010200(slab|head|node=0|zone=2|lastcpupid=0x1ffff) raw: 002ffff800010200 0000000000000000 dead000000000122 ffff88810004cf00 raw: 0000000000000000 0000000080080008 00000002ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888976250000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888976250080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb > ffff888976250100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff888976250180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888976250200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: 718a18a0 ("veth: Rework veth_xdp_rcv_skb in order to accept non-linear skb") Signed-off-by:
Shawn Bohrer <sbohrer@cloudflare.com> Acked-by:
Lorenzo Bianconi <lorenzo@kernel.org> Acked-by:
Toshiaki Makita <toshiaki.makita1@gmail.com> Acked-by:
Toke Høiland-Jørgensen <toke@kernel.org> Link: https://lore.kernel.org/r/20230314153351.2201328-1-sbohrer@cloudflare.comSigned-off-by:
-
- 15 Mar, 2023 16 commits
-
-
David S. Miller authored
Daniel Golle says: ==================== net: ethernet: mtk_eth_soc: minor SGMII fixes This small series brings two minor fixes for the SGMII unit found in MediaTek's router SoCs. The first patch resets the PCS internal state machine on major configuration changes, just like it is also done in MediaTek's SDK. The second patch makes sure we only write values and restart AN if actually needed, thus preventing unnesseray loss of an existing link in some cases. Both patches have previously been submitted as part of the series "net: ethernet: mtk_eth_soc: various enhancements" which grew a bit too big and it has correctly been criticized that some of the patches should rather go as fixes to net-next. This new series tries to address this. ==================== Signed-off-by: -
Daniel Golle authored
Only restart auto-negotiation and write link timer if actually necessary. This prevents losing the link in case of minor changes. Fixes: 7e538372 ("net: ethernet: mediatek: Re-add support SGMII") Reviewed-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Tested-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Daniel Golle <daniel@makrotopia.org> Signed-off-by:
-
Daniel Golle authored
Reset the internal PCS state machine when changing interface mode. This prevents confusing the state machine when changing interface modes, e.g. from SGMII to 2500Base-X or vice-versa. Fixes: 7e538372 ("net: ethernet: mediatek: Re-add support SGMII") Reviewed-by:
-
Szymon Heidrich authored
Packet length retrieved from skb data may be larger than the actual socket buffer length (up to 9026 bytes). In such case the cloned skb passed up the network stack will leak kernel memory contents. Fixes: d0cad871 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver") Signed-off-by:
Szymon Heidrich <szymon.heidrich@gmail.com> Signed-off-by:
-
David S. Miller authored
Wenjia Zhang says: ==================== net/smc: Fixes 2023-03-01 The 1st patch solves the problem that CLC message initialization was not properly reversed in error handling path. And the 2nd one fixes the possible deadlock triggered by cancel_delayed_work_sync(). ==================== Signed-off-by: -
Stefan Raspl authored
CLC message initialization was not properly reversed in error handling path. Reported-and-suggested-by:
Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by:
Stefan Raspl <raspl@linux.ibm.com> Signed-off-by:
Wenjia Zhang <wenjia@linux.ibm.com> Reviewed-by:
Tony Lu <tonylu@linux.alibaba.com> Signed-off-by:
-
Wenjia Zhang authored
The following LOCKDEP was detected: Workqueue: events smc_lgr_free_work [smc] WARNING: possible circular locking dependency detected 6.1.0-20221027.rc2.git8.56bc5b569087.300.fc36.s390x+debug #1 Not tainted ------------------------------------------------------ kworker/3:0/176251 is trying to acquire lock: 00000000f1467148 ((wq_completion)smc_tx_wq-00000000#2){+.+.}-{0:0}, at: __flush_workqueue+0x7a/0x4f0 but task is already holding lock: 0000037fffe97dc8 ((work_completion)(&(&lgr->free_work)->work)){+.+.}-{0:0}, at: process_one_work+0x232/0x730 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #4 ((work_completion)(&(&lgr->free_work)->work)){+.+.}-{0:0}: __lock_acquire+0x58e/0xbd8 lock_acquire.part.0+0xe2/0x248 lock_acquire+0xac/0x1c8 __flush_work+0x76/0xf0 __cancel_work_timer+0x170/0x220 __smc_lgr_terminate.part.0+0x34/0x1c0 [smc] smc_connect_rdma+0x15e/0x418 [smc] __smc_connect+0x234/0x480 [smc] smc_connect+0x1d6/0x230 [smc] __sys_connect+0x90/0xc0 __do_sys_socketcall+0x186/0x370 __do_syscall+0x1da/0x208 system_call+0x82/0xb0 -> #3 (smc_client_lgr_pending){+.+.}-{3:3}: __lock_acquire+0x58e/0xbd8 lock_acquire.part.0+0xe2/0x248 lock_acquire+0xac/0x1c8 __mutex_lock+0x96/0x8e8 mutex_lock_nested+0x32/0x40 smc_connect_rdma+0xa4/0x418 [smc] __smc_connect+0x234/0x480 [smc] smc_connect+0x1d6/0x230 [smc] __sys_connect+0x90/0xc0 __do_sys_socketcall+0x186/0x370 __do_syscall+0x1da/0x208 system_call+0x82/0xb0 -> #2 (sk_lock-AF_SMC){+.+.}-{0:0}: __lock_acquire+0x58e/0xbd8 lock_acquire.part.0+0xe2/0x248 lock_acquire+0xac/0x1c8 lock_sock_nested+0x46/0xa8 smc_tx_work+0x34/0x50 [smc] process_one_work+0x30c/0x730 worker_thread+0x62/0x420 kthread+0x138/0x150 __ret_from_fork+0x3c/0x58 ret_from_fork+0xa/0x40 -> #1 ((work_completion)(&(&smc->conn.tx_work)->work)){+.+.}-{0:0}: __lock_acquire+0x58e/0xbd8 lock_acquire.part.0+0xe2/0x248 lock_acquire+0xac/0x1c8 process_one_work+0x2bc/0x730 worker_thread+0x62/0x420 kthread+0x138/0x150 __ret_from_fork+0x3c/0x58 ret_from_fork+0xa/0x40 -> #0 ((wq_completion)smc_tx_wq-00000000#2){+.+.}-{0:0}: check_prev_add+0xd8/0xe88 validate_chain+0x70c/0xb20 __lock_acquire+0x58e/0xbd8 lock_acquire.part.0+0xe2/0x248 lock_acquire+0xac/0x1c8 __flush_workqueue+0xaa/0x4f0 drain_workqueue+0xaa/0x158 destroy_workqueue+0x44/0x2d8 smc_lgr_free+0x9e/0xf8 [smc] process_one_work+0x30c/0x730 worker_thread+0x62/0x420 kthread+0x138/0x150 __ret_from_fork+0x3c/0x58 ret_from_fork+0xa/0x40 other info that might help us debug this: Chain exists of: (wq_completion)smc_tx_wq-00000000#2 --> smc_client_lgr_pending --> (work_completion)(&(&lgr->free_work)->work) Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock((work_completion)(&(&lgr->free_work)->work)); lock(smc_client_lgr_pending); lock((work_completion) (&(&lgr->free_work)->work)); lock((wq_completion)smc_tx_wq-00000000#2); *** DEADLOCK *** 2 locks held by kworker/3:0/176251: #0: 0000000080183548 ((wq_completion)events){+.+.}-{0:0}, at: process_one_work+0x232/0x730 #1: 0000037fffe97dc8 ((work_completion) (&(&lgr->free_work)->work)){+.+.}-{0:0}, at: process_one_work+0x232/0x730 stack backtrace: CPU: 3 PID: 176251 Comm: kworker/3:0 Not tainted Hardware name: IBM 8561 T01 701 (z/VM 7.2.0) Call Trace: [<000000002983c3e4>] dump_stack_lvl+0xac/0x100 [<0000000028b477ae>] check_noncircular+0x13e/0x160 [<0000000028b48808>] check_prev_add+0xd8/0xe88 [<0000000028b49cc4>] validate_chain+0x70c/0xb20 [<0000000028b4bd26>] __lock_acquire+0x58e/0xbd8 [<0000000028b4cf6a>] lock_acquire.part.0+0xe2/0x248 [<0000000028b4d17c>] lock_acquire+0xac/0x1c8 [<0000000028addaaa>] __flush_workqueue+0xaa/0x4f0 [<0000000028addf9a>] drain_workqueue+0xaa/0x158 [<0000000028ae303c>] destroy_workqueue+0x44/0x2d8 [<000003ff8029af26>] smc_lgr_free+0x9e/0xf8 [smc] [<0000000028adf3d4>] process_one_work+0x30c/0x730 [<0000000028adf85a>] worker_thread+0x62/0x420 [<0000000028aeac50>] kthread+0x138/0x150 [<0000000028a63914>] __ret_from_fork+0x3c/0x58 [<00000000298503da>] ret_from_fork+0xa/0x40 INFO: lockdep is turned off. =================================================================== This deadlock occurs because cancel_delayed_work_sync() waits for the work(&lgr->free_work) to finish, while the &lgr->free_work waits for the work(lgr->tx_wq), which needs the sk_lock-AF_SMC, that is already used under the mutex_lock. The solution is to use cancel_delayed_work() instead, which kills off a pending work. Fixes: a52bcc91 ("net/smc: improve termination processing") Signed-off-by:Jan Karcher <jaka@linux.ibm.com> Reviewed-by:
Karsten Graul <kgraul@linux.ibm.com> Reviewed-by:
-
Ido Schimmel authored
Spectrum ASICs have a configurable limit on how deep into the packet they parse. By default, the limit is 96 bytes. There are several cases where this parsing depth is not enough and there is a need to increase it. For example, timestamping of PTP packets and a FIB multipath hash policy that requires hashing on inner fields. The driver therefore maintains a reference count that reflects the number of consumers that require an increased parsing depth. During reload_down() the parsing depth reference count does not necessarily drop to zero, but the parsing depth itself is restored to the default during reload_up() when the firmware is reset. It is therefore possible to end up in situations where the driver thinks that the parsing depth was increased (reference count is non-zero), when it is not. Fix by making sure that all the consumers that increase the parsing depth reference count also decrease it during reload_down(). Specifically, make sure that when the routing code is de-initialized it drops the reference count if it was increased because of a FIB multipath hash policy that requires hashing on inner fields. Add a warning if the reference count is not zero after the driver was de-initialized and explicitly reset it to zero during initialization for good measures. Fixes: 2d91f080 ("mlxsw: spectrum: Add infrastructure for parsing configuration") Reported-by:
Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/9c35e1b3e6c1d8f319a2449d14e2b86373f3b3ba.1678727526.git.petrm@nvidia.comSigned-off-by:
-
Lorenzo Bianconi authored
Fix the following kernel warning in veth_set_xdp_features routine relying on rtnl_dereference() instead of on rcu_dereference(): ============================= WARNING: suspicious RCU usage 6.3.0-rc1-00144-g064d7052 #149 Not tainted ----------------------------- drivers/net/veth.c:1265 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 1 lock held by ip/135: (net/core/rtnetlink.c:6172) stack backtrace: CPU: 1 PID: 135 Comm: ip Not tainted 6.3.0-rc1-00144-g064d7052 #149 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:107) lockdep_rcu_suspicious (include/linux/context_tracking.h:152) veth_set_xdp_features (drivers/net/veth.c:1265 (discriminator 9)) veth_newlink (drivers/net/veth.c:1892) ? veth_set_features (drivers/net/veth.c:1774) ? kasan_save_stack (mm/kasan/common.c:47) ? kasan_save_stack (mm/kasan/common.c:46) ? kasan_set_track (mm/kasan/common.c:52) ? alloc_netdev_mqs (include/linux/slab.h:737) ? rcu_read_lock_sched_held (kernel/rcu/update.c:125) ? trace_kmalloc (include/trace/events/kmem.h:54) ? __xdp_rxq_info_reg (net/core/xdp.c:188) ? alloc_netdev_mqs (net/core/dev.c:10657) ? rtnl_create_link (net/core/rtnetlink.c:3312) rtnl_newlink_create (net/core/rtnetlink.c:3440) ? rtnl_link_get_net_capable.constprop.0 (net/core/rtnetlink.c:3391) __rtnl_newlink (net/core/rtnetlink.c:3657) ? lock_downgrade (kernel/locking/lockdep.c:5321) ? rtnl_link_unregister (net/core/rtnetlink.c:3487) rtnl_newlink (net/core/rtnetlink.c:3671) rtnetlink_rcv_msg (net/core/rtnetlink.c:6174) ? rtnl_link_fill (net/core/rtnetlink.c:6070) ? mark_usage (kernel/locking/lockdep.c:4914) ? mark_usage (kernel/locking/lockdep.c:4914) netlink_rcv_skb (net/netlink/af_netlink.c:2574) ? rtnl_link_fill (net/core/rtnetlink.c:6070) ? netlink_ack (net/netlink/af_netlink.c:2551) ? lock_acquire (kernel/locking/lockdep.c:467) ? net_generic (include/linux/rcupdate.h:805) ? netlink_deliver_tap (include/linux/rcupdate.h:805) netlink_unicast (net/netlink/af_netlink.c:1340) ? netlink_attachskb (net/netlink/af_netlink.c:1350) netlink_sendmsg (net/netlink/af_netlink.c:1942) ? netlink_unicast (net/netlink/af_netlink.c:1861) ? netlink_unicast (net/netlink/af_netlink.c:1861) sock_sendmsg (net/socket.c:727) ____sys_sendmsg (net/socket.c:2501) ? kernel_sendmsg (net/socket.c:2448) ? __copy_msghdr (net/socket.c:2428) ___sys_sendmsg (net/socket.c:2557) ? mark_usage (kernel/locking/lockdep.c:4914) ? do_recvmmsg (net/socket.c:2544) ? lock_acquire (kernel/locking/lockdep.c:467) ? find_held_lock (kernel/locking/lockdep.c:5159) ? __lock_release (kernel/locking/lockdep.c:5345) ? __might_fault (mm/memory.c:5625) ? lock_downgrade (kernel/locking/lockdep.c:5321) ? __fget_light (include/linux/atomic/atomic-arch-fallback.h:227) __sys_sendmsg (include/linux/file.h:31) ? __sys_sendmsg_sock (net/socket.c:2572) ? rseq_get_rseq_cs (kernel/rseq.c:275) ? lockdep_hardirqs_on_prepare.part.0 (kernel/locking/lockdep.c:4263) do_syscall_64 (arch/x86/entry/common.c:50) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) RIP: 0033:0x7f0d1aadeb17 Code: 0f 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10 Fixes: fccca038 ("veth: take into account device reconfiguration for xdp_features flag") Suggested-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Link: https://lore.kernel.org/netdev/cover.1678364612.git.lorenzo@kernel.org/T/#me4c9d8e985ec7ebee981cfdb5bc5ec651ef4035dSigned-off-by:
-
Zheng Wang authored
This bug influences both st_nci_i2c_remove and st_nci_spi_remove. Take st_nci_i2c_remove as an example. In st_nci_i2c_probe, it called ndlc_probe and bound &ndlc->sm_work with llt_ndlc_sm_work. When it calls ndlc_recv or timeout handler, it will finally call schedule_work to start the work. When we call st_nci_i2c_remove to remove the driver, there may be a sequence as follows: Fix it by finishing the work before cleanup in ndlc_remove CPU0 CPU1 |llt_ndlc_sm_work st_nci_i2c_remove | ndlc_remove | st_nci_remove | nci_free_device| kfree(ndev) | //free ndlc->ndev | |llt_ndlc_rcv_queue |nci_recv_frame |//use ndlc->ndev Fixes: 35630df6 ("NFC: st21nfcb: Add driver for STMicroelectronics ST21NFCB NFC chip") Signed-off-by:Zheng Wang <zyytlz.wz@163.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230312160837.2040857-1-zyytlz.wz@163.comSigned-off-by:
-
Jakub Kicinski authored
Kuniyuki Iwashima says: ==================== tcp: Fix bind() regression for dual-stack wildcard address. The first patch fixes the regression reported in [0], and the second patch adds a test for similar cases to catch future regression. [0]: https://lore.kernel.org/netdev/e21bf153-80b0-9ec0-15ba-e04a4ad42c34@redhat.com/ ==================== Link: https://lore.kernel.org/r/20230312031904.4674-1-kuniyu@amazon.comSigned-off-by:
-
Kuniyuki Iwashima authored
The test checks if (IPv4, IPv6) address pair properly conflict or not. * IPv4 * 0.0.0.0 * 127.0.0.1 * IPv6 * :: * ::1 If the IPv6 address is [::], the second bind() always fails. Signed-off-by:Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by:
-
Kuniyuki Iwashima authored
Paul Holzinger reported [0] that commit 5456262d ("net: Fix incorrect address comparison when searching for a bind2 bucket") introduced a bind() regression. Paul also gave a nice repro that calls two types of bind() on the same port, both of which now succeed, but the second call should fail: bind(fd1, ::, port) + bind(fd2, 127.0.0.1, port) The cited commit added address family tests in three functions to fix the uninit-value KMSAN report. [1] However, the test added to inet_bind2_bucket_match_addr_any() removed a necessary conflict check; the dual-stack wildcard address no longer conflicts with an IPv4 non-wildcard address. If tb->family is AF_INET6 and sk->sk_family is AF_INET in inet_bind2_bucket_match_addr_any(), we still need to check if tb has the dual-stack wildcard address. Note that the IPv4 wildcard address does not conflict with IPv6 non-wildcard addresses. [0]: https://lore.kernel.org/netdev/e21bf153-80b0-9ec0-15ba-e04a4ad42c34@redhat.com/ [1]: https://lore.kernel.org/netdev/CAG_fn=Ud3zSW7AZWXc+asfMhZVL5ETnvuY44Pmyv4NPv-ijN-A@mail.gmail.com/ Fixes: 5456262d ("net: Fix incorrect address comparison when searching for a bind2 bucket") Signed-off-by:
Paul Holzinger <pholzing@redhat.com> Link: https://lore.kernel.org/netdev/CAG_fn=Ud3zSW7AZWXc+asfMhZVL5ETnvuY44Pmyv4NPv-ijN-A@mail.gmail.com/Reviewed-by:
Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by:
-
Heiner Kallweit authored
If genphy_read_status fails then further access to the PHY may result in unpredictable behavior. To prevent this bail out immediately if genphy_read_status fails. Fixes: 4223dbff ("net: phy: smsc: Re-enable EDPD mode for LAN87xx") Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
-
Eric Dumazet authored
IP tunnels can apparently update dev->needed_headroom in their xmit path. This patch takes care of three tunnels xmit, and also the core LL_RESERVED_SPACE() and LL_RESERVED_SPACE_EXTRA() helpers. More changes might be needed for completeness. BUG: KCSAN: data-race in ip_tunnel_xmit / ip_tunnel_xmit read to 0xffff88815b9da0ec of 2 bytes by task 888 on cpu 1: ip_tunnel_xmit+0x1270/0x1730 net/ipv4/ip_tunnel.c:803 __gre_xmit net/ipv4/ip_gre.c:469 [inline] ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661 __netdev_start_xmit include/linux/netdevice.h:4881 [inline] netdev_start_xmit include/linux/netdevice.h:4895 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596 __dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246 dev_queue_xmit include/linux/netdevice.h:3051 [inline] neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623 neigh_output include/net/neighbour.h:546 [inline] ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228 ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:291 [inline] ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430 dst_output include/net/dst.h:444 [inline] ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126 iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82 ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813 __gre_xmit net/ipv4/ip_gre.c:469 [inline] ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661 __netdev_start_xmit include/linux/netdevice.h:4881 [inline] netdev_start_xmit include/linux/netdevice.h:4895 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596 __dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246 dev_queue_xmit include/linux/netdevice.h:3051 [inline] neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623 neigh_output include/net/neighbour.h:546 [inline] ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228 ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:291 [inline] ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430 dst_output include/net/dst.h:444 [inline] ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126 iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82 ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813 __gre_xmit net/ipv4/ip_gre.c:469 [inline] ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661 __netdev_start_xmit include/linux/netdevice.h:4881 [inline] netdev_start_xmit include/linux/netdevice.h:4895 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596 __dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246 dev_queue_xmit include/linux/netdevice.h:3051 [inline] neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623 neigh_output include/net/neighbour.h:546 [inline] ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228 ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:291 [inline] ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430 dst_output include/net/dst.h:444 [inline] ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126 iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82 ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813 __gre_xmit net/ipv4/ip_gre.c:469 [inline] ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661 __netdev_start_xmit include/linux/netdevice.h:4881 [inline] netdev_start_xmit include/linux/netdevice.h:4895 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596 __dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246 dev_queue_xmit include/linux/netdevice.h:3051 [inline] neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623 neigh_output include/net/neighbour.h:546 [inline] ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228 ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:291 [inline] ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430 dst_output include/net/dst.h:444 [inline] ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126 iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82 ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813 __gre_xmit net/ipv4/ip_gre.c:469 [inline] ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661 __netdev_start_xmit include/linux/netdevice.h:4881 [inline] netdev_start_xmit include/linux/netdevice.h:4895 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596 __dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246 dev_queue_xmit include/linux/netdevice.h:3051 [inline] neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623 neigh_output include/net/neighbour.h:546 [inline] ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228 ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:291 [inline] ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430 dst_output include/net/dst.h:444 [inline] ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126 iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82 ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813 __gre_xmit net/ipv4/ip_gre.c:469 [inline] ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661 __netdev_start_xmit include/linux/netdevice.h:4881 [inline] netdev_start_xmit include/linux/netdevice.h:4895 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596 __dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246 dev_queue_xmit include/linux/netdevice.h:3051 [inline] neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623 neigh_output include/net/neighbour.h:546 [inline] ip_finish_output2+0x740/0x840 net/ipv4/ip_output.c:228 ip_finish_output+0xf4/0x240 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:291 [inline] ip_output+0xe5/0x1b0 net/ipv4/ip_output.c:430 dst_output include/net/dst.h:444 [inline] ip_local_out+0x64/0x80 net/ipv4/ip_output.c:126 iptunnel_xmit+0x34a/0x4b0 net/ipv4/ip_tunnel_core.c:82 ip_tunnel_xmit+0x1451/0x1730 net/ipv4/ip_tunnel.c:813 __gre_xmit net/ipv4/ip_gre.c:469 [inline] ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661 __netdev_start_xmit include/linux/netdevice.h:4881 [inline] netdev_start_xmit include/linux/netdevice.h:4895 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596 __dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246 write to 0xffff88815b9da0ec of 2 bytes by task 2379 on cpu 0: ip_tunnel_xmit+0x1294/0x1730 net/ipv4/ip_tunnel.c:804 __gre_xmit net/ipv4/ip_gre.c:469 [inline] ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:661 __netdev_start_xmit include/linux/netdevice.h:4881 [inline] netdev_start_xmit include/linux/netdevice.h:4895 [inline] xmit_one net/core/dev.c:3580 [inline] dev_hard_start_xmit+0x127/0x400 net/core/dev.c:3596 __dev_queue_xmit+0x1007/0x1eb0 net/core/dev.c:4246 dev_queue_xmit include/linux/netdevice.h:3051 [inline] neigh_direct_output+0x17/0x20 net/core/neighbour.c:1623 neigh_output include/net/neighbour.h:546 [inline] ip6_finish_output2+0x9bc/0xc50 net/ipv6/ip6_output.c:134 __ip6_finish_output net/ipv6/ip6_output.c:195 [inline] ip6_finish_output+0x39a/0x4e0 net/ipv6/ip6_output.c:206 NF_HOOK_COND include/linux/netfilter.h:291 [inline] ip6_output+0xeb/0x220 net/ipv6/ip6_output.c:227 dst_output include/net/dst.h:444 [inline] NF_HOOK include/linux/netfilter.h:302 [inline] mld_sendpack+0x438/0x6a0 net/ipv6/mcast.c:1820 mld_send_cr net/ipv6/mcast.c:2121 [inline] mld_ifc_work+0x519/0x7b0 net/ipv6/mcast.c:2653 process_one_work+0x3e6/0x750 kernel/workqueue.c:2390 worker_thread+0x5f2/0xa10 kernel/workqueue.c:2537 kthread+0x1ac/0x1e0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308 value changed: 0x0dd4 -> 0x0e14 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 2379 Comm: kworker/0:0 Not tainted 6.3.0-rc1-syzkaller-00002-g8ca09d5f-dirty #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/02/2023 Workqueue: mld mld_ifc_work Fixes: 8eb30be0 ("ipv6: Create ip6_tnl_xmit") Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Dave Ertman authored
RDMA is not supported in ice on a PF that has been added to a bonded interface. To enforce this, when an interface enters a bond, we unplug the auxiliary device that supports RDMA functionality. This unplug currently happens in the context of handling the netdev bonding event. This event is sent to the ice driver under RTNL context. This is causing a deadlock where the RDMA driver is waiting for the RTNL lock to complete the removal. Defer the unplugging/re-plugging of the auxiliary device to the service task so that it is not performed under the RTNL lock context. Cc: stable@vger.kernel.org # 6.1.x Reported-by:
Jaroslav Pulchart <jaroslav.pulchart@gooddata.com> Link: https://lore.kernel.org/netdev/CAK8fFZ6A_Gphw_3-QMGKEFQk=sfCw1Qmq0TVZK3rtAi7vb621A@mail.gmail.com/ Fixes: 5cb1ebdb ("ice: Fix race condition during interface enslave") Fixes: 4eace75e ("RDMA/irdma: Report the correct link speed") Signed-off-by:
Dave Ertman <david.m.ertman@intel.com> Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel) Signed-off-by:
-
- 14 Mar, 2023 4 commits
-
-
Kristian Overskeid authored
If no frames has been exchanged with a node for HSR_NODE_FORGET_TIME, the node will be deleted from the node_db list. If a frame is sent to the node after it is deleted, a netdev_err message for each slave interface is produced. This should not happen with dan nodes because of supervision frames, but can happen often with san nodes, which clutters the kernel log. Since the hsr protocol does not support sans, this is only relevant for the prp protocol. Signed-off-by:
Kristian Overskeid <koverskeid@gmail.com> Signed-off-by:
-
Alex Elder authored
A recent commit eliminated a hack that adjusted the offset used for many GSI registers. It became possible because we now specify all GSI register offsets explicitly for every version of IPA. Unfortunately, a large number of register offsets were *not* updated as they should have been in that commit. For IPA v4.5+, the offset for every GSI register *except* the two inter-EE interrupt masking registers were supposed to have been reduced by 0xd000. Tested-by:
Luca Weiss <luca.weiss@fairphone.com> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK Fixes: 59b12b1d ("net: ipa: kill gsi->virt_raw") Signed-off-by:
Alex Elder <elder@linaro.org> Link: https://lore.kernel.org/r/20230310193709.1477102-1-elder@linaro.orgSigned-off-by:
-
Arınç ÜNAL authored
As my testing on the MCM MT7530 switch on MT7621 SoC shows, setting the PLL frequency does not affect MII modes other than trgmii on port 5 and port 6. So the assumption is that the operation here called "setting the PLL frequency" actually sets the frequency of the TRGMII TX clock. Make it so that it and the rest of the trgmii setup run only when the trgmii mode is used. Tested rgmii and trgmii modes of port 6 on MCM MT7530 on MT7621AT Unielec U7621-06 and standalone MT7530 on MT7623NI Bananapi BPI-R2. Fixes: b8f126a8 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Tested-by:
Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by:
-
Arınç ÜNAL authored
Remove now incorrect comment regarding port 5 as GMAC5. This is supposed to be supported since commit 38f790a8 ("net: dsa: mt7530: Add support for port 5") under mt7530_setup_port5(). Fixes: 38f790a8 ("net: dsa: mt7530: Add support for port 5") Signed-off-by:
-
- 13 Mar, 2023 3 commits
-
-
Daniil Tatianin authored
Previously we would divide total_left_rate by zero if num_vports happened to be 1 because non_requested_count is calculated as num_vports - req_count. Guard against this by validating num_vports at the beginning and returning an error otherwise. Found by Linux Verification Center (linuxtesting.org) with the SVACE static analysis tool. Fixes: bcd197c8 ("qed: Add vport WFQ configuration APIs") Signed-off-by:
Daniil Tatianin <d-tatianin@yandex-team.ru> Reviewed-by:
-
D. Wythe authored
When performing a stress test on SMC-R by rmmod mlx5_ib driver during the wrk/nginx test, we found that there is a probability of triggering a panic while terminating all link groups. This issue dues to the race between smc_smcr_terminate_all() and smc_buf_create(). smc_smcr_terminate_all smc_buf_create /* init */ conn->sndbuf_desc = NULL; ... __smc_lgr_terminate smc_conn_kill smc_close_abort smc_cdc_get_slot_and_msg_send __softirqentry_text_start smc_wr_tx_process_cqe smc_cdc_tx_handler READ(conn->sndbuf_desc->len); /* panic dues to NULL sndbuf_desc */ conn->sndbuf_desc = xxx; This patch tries to fix the issue by always to check the sndbuf_desc before send any cdc msg, to make sure that no null pointer is seen during cqe processing. Fixes: 0b29ec64 ("net/smc: immediate termination for SMCR link groups") Signed-off-by:
D. Wythe <alibuda@linux.alibaba.com> Reviewed-by:
-
Vadim Fedorenko authored
When using a PHC in shared between multiple hosts, the previous frequency value may not be reset and could lead to host being unable to compensate the offset with timecounter adjustments. To avoid such state reset the hardware frequency of PHC to zero on init. Some refactoring is needed to make code readable. Fixes: 85036aee ("bnxt_en: Add a non-real time mode to access NIC clock") Signed-off-by:
Vadim Fedorenko <vadfed@meta.com> Reviewed-by:
Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/20230310151356.678059-1-vadfed@meta.comSigned-off-by:
-
- 11 Mar, 2023 8 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nfJakub Kicinski authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net 1) nft_parse_register_load() gets an incorrect datatype size as input, from Jeremy Sowden. 2) incorrect maximum netlink attribute in nft_redir, also from Jeremy. * git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf: netfilter: nft_redir: correct value of inet type `.maxattrs` netfilter: nft_redir: correct length for loading protocol registers netfilter: nft_masq: correct length for loading protocol registers netfilter: nft_nat: correct length for loading protocol registers ==================== Link: https://lore.kernel.org/r/20230309174655.69816-1-pablo@netfilter.orgSigned-off-by:
-
Jakub Kicinski authored
Matthieu Baerts says: ==================== mptcp: fixes for 6.3 Patch 1 fixes a possible deadlock in subflow_error_report() reported by lockdep. The report was in fact a false positive but the modification makes sense and silences lockdep to allow syzkaller to find real issues. The regression has been introduced in v5.12. Patch 2 is a refactoring needed to be able to fix the two next issues. It improves the situation and can be backported up to v6.0. Patches 3 and 4 fix UaF reported by KASAN. It fixes issues potentially visible since v5.7 and v5.19 but only reproducible until recently (v6.0). These two patches depend on patch 2/7. Patch 5 fixes the order of the printed values: expected vs seen values. The regression has been introduced recently: v6.3-rc1. Patch 6 adds missing ro_after_init flags. A previous patch added them for other functions but these two have been missed. This previous patch has been backported to stable versions (up to v5.12) so probably better to do the same here. Patch 7 fixes tcp_set_state() being called twice in a row since v5.10. Patch 8 fixes another lockdep false positive issue but this time in MPTCP PM code. Same here, some modifications in the code has been made to silence this issue and help finding real ones later. This issue can be seen since v6.2. v1: https://lore.kernel.org/r/20230227-upstream-net-20230227-mptcp-fixes-v1-0-070e30ae4a8e@tessares.net ==================== Link: https://lore.kernel.org/r/20230227-upstream-net-20230227-mptcp-fixes-v2-0-47c2e95eada9@tessares.netSigned-off-by:
-
Paolo Abeni authored
Christoph reports a lockdep splat in the mptcp_subflow_create_socket() error path, when such function is invoked by mptcp_pm_nl_create_listen_socket(). Such code path acquires two separates, nested socket lock, with the internal lock operation lacking the "nested" annotation. Adding that in sock_release() for mptcp's sake only could be confusing. Instead just add a new lockclass to the in-kernel msk socket, re-initializing the lockdep infra after the socket creation. Fixes: ad217100 ("mptcp: fix locking for in-kernel listener creation") Cc: stable@vger.kernel.org Reported-by:
Christoph Paasch <cpaasch@apple.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/354Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
-
Matthieu Baerts authored
tcp_set_state() is called from tcp_done() already. There is then no need to first set the state to TCP_CLOSE, then call tcp_done(). Fixes: d5824847 ("mptcp: fix fallback for MP_JOIN subflows") Cc: stable@vger.kernel.org Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/362Acked-by:
-
Geliang Tang authored
Add __ro_after_init labels for the variables tcp_prot_override and tcpv6_prot_override, just like other variables adjacent to them, to indicate that they are initialised from the init hooks and no writes occur afterwards. Fixes: b19bc294 ("mptcp: implement delegated actions") Cc: stable@vger.kernel.org Fixes: 51fa7f8e ("mptcp: mark ops structures as ro_after_init") Signed-off-by:
Geliang Tang <geliang.tang@suse.com> Reviewed-by:
-
Matthieu Baerts authored
In case of errors, the printed message had the expected and the seen value inverted. This patch simply correct the order: first the expected value, then the one that has been seen. Fixes: 10d42734 ("selftests: mptcp: userspace: print error details if any") Cc: stable@vger.kernel.org Acked-by:
-
Paolo Abeni authored
As reported by Christoph after having refactored the passive socket initialization, the mptcp listener shutdown path is prone to an UaF issue. BUG: KASAN: use-after-free in _raw_spin_lock_bh+0x73/0xe0 Write of size 4 at addr ffff88810cb23098 by task syz-executor731/1266 CPU: 1 PID: 1266 Comm: syz-executor731 Not tainted 6.2.0-rc59af4eaa31c1f6c00c8f1e448ed99a45c66340dd5 #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x6e/0x91 print_report+0x16a/0x46f kasan_report+0xad/0x130 kasan_check_range+0x14a/0x1a0 _raw_spin_lock_bh+0x73/0xe0 subflow_error_report+0x6d/0x110 sk_error_report+0x3b/0x190 tcp_disconnect+0x138c/0x1aa0 inet_child_forget+0x6f/0x2e0 inet_csk_listen_stop+0x209/0x1060 __mptcp_close_ssk+0x52d/0x610 mptcp_destroy_common+0x165/0x640 mptcp_destroy+0x13/0x80 __mptcp_destroy_sock+0xe7/0x270 __mptcp_close+0x70e/0x9b0 mptcp_close+0x2b/0x150 inet_release+0xe9/0x1f0 __sock_release+0xd2/0x280 sock_close+0x15/0x20 __fput+0x252/0xa20 task_work_run+0x169/0x250 exit_to_user_mode_prepare+0x113/0x120 syscall_exit_to_user_mode+0x1d/0x40 do_syscall_64+0x48/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc The msk grace period can legitly expire in between the last reference count dropped in mptcp_subflow_queue_clean() and the later eventual access in inet_csk_listen_stop() After the previous patch we don't need anymore special-casing msk listener socket cleanup: the mptcp worker will process each of the unaccepted msk sockets. Just drop the now unnecessary code. Please note this commit depends on the two parent ones: mptcp: refactor passive socket initialization mptcp: use the workqueue to destroy unaccepted sockets Fixes: 6aeed904 ("mptcp: fix race on unaccepted mptcp sockets") Cc: stable@vger.kernel.org Reported-and-tested-by:
-
Paolo Abeni authored
Christoph reported a UaF at token lookup time after having refactored the passive socket initialization part: BUG: KASAN: use-after-free in __token_bucket_busy+0x253/0x260 Read of size 4 at addr ffff88810698d5b0 by task syz-executor653/3198 CPU: 1 PID: 3198 Comm: syz-executor653 Not tainted 6.2.0-rc59af4eaa31c1f6c00c8f1e448ed99a45c66340dd5 #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x6e/0x91 print_report+0x16a/0x46f kasan_report+0xad/0x130 __token_bucket_busy+0x253/0x260 mptcp_token_new_connect+0x13d/0x490 mptcp_connect+0x4ed/0x860 __inet_stream_connect+0x80e/0xd90 tcp_sendmsg_fastopen+0x3ce/0x710 mptcp_sendmsg+0xff1/0x1a20 inet_sendmsg+0x11d/0x140 __sys_sendto+0x405/0x490 __x64_sys_sendto+0xdc/0x1b0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc We need to properly clean-up all the paired MPTCP-level resources and be sure to release the msk last, even when the unaccepted subflow is destroyed by the TCP internals via inet_child_forget(). We can re-use the existing MPTCP_WORK_CLOSE_SUBFLOW infra, explicitly checking that for the critical scenario: the closed subflow is the MPC one, the msk is not accepted and eventually going through full cleanup. With such change, __mptcp_destroy_sock() is always called on msk sockets, even on accepted ones. We don't need anymore to transiently drop one sk reference at msk clone time. Please note this commit depends on the parent one: mptcp: refactor passive socket initialization Fixes: 58b09919 ("mptcp: create msk early") Cc: stable@vger.kernel.org Reported-and-tested-by:
-
