Remove code duplicity and move it to SAVE_STATE macro.
There is no impact on performance.
Signed-off-by: Michal Simek <monstr@monstr.eu>

We don't need to protect by BIP whole ret_from_trap/ret_from_exc code.
Only restoring from user/hw exception should be covered.
If BIP is setup, IRQ can't occur.
Signed-off-by: Michal Simek <monstr@monstr.eu>

There is a way howto remove Kernel Mode variable. It is easier
to parse UMS bit in MSR to find out if I come from kernel or user
space. Loading MSR content should be in one cycle and loading
PER_CPU variable depends on memory state.
Signed-off-by: Michal Simek <monstr@monstr.eu>

We can save two instruction when MSR_VMS and MSR_UMS
are setup in one instruction.
Signed-off-by: Michal Simek <monstr@monstr.eu>

Save and restore R3/R4 registers in macros. This change
help to cleanup entry.S.

In ret_from_trap function we are saving returning value from
syscall to pt_regs on stack that's why we don't need to save and
restore these values before kernel functions (schedule, do_signal).
Signed-off-by: Michal Simek <monstr@monstr.eu>

Jump behind macro. We don't want to execute nop instruction again.
Signed-off-by: Michal Simek <monstr@monstr.eu>

_start symbol stores physical address where kernel is.
Gdb uses this symbol for their purpose that's why
we have to rename it.
Signed-off-by: Michal Simek <monstr@monstr.eu>

Remove spaces and use tabs instead.
Signed-off-by: Michal Simek <monstr@monstr.eu>

Microblaze has only 11 pvr regs according manual.
Signed-off-by: Michal Simek <monstr@monstr.eu>

Lower shifting values ensure that shifted 32bit counter
value doesn't exceed 64bit cycle variable too fast.
Signed-off-by: Michal Simek <monstr@monstr.eu>

Microblaze has support for early printk. The second serial
driver (uart16550/8250) has no microblaze support for early
printk.
Signed-off-by: Michal Simek <monstr@monstr.eu>

HAVE_ARCH_PCI_SET_DMA_MASK was removed in 2.6.34 (no architecture has
the own implementation of pci_set_dma_mask).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Michal Simek <monstr@monstr.eu>

IRQsoff tracer requires to protect cpu_idle function
to get correct timing report.
Signed-off-by: Michal Simek <monstr@monstr.eu>

I had to comment sched_clock generic function because of broken toolchain.
It is fine grain timing.
Signed-off-by: Michal Simek <monstr@monstr.eu>

Implement intelligent backtracing by searching for stack frame creation,
and emitting only return addresses. Use print_hex_dump() to display the
entire binary kernel stack.

Limitation: MMU kernels are not currently able to trace beyond a system trap
(interrupt, syscall, etc.). It is the intent of this patch to provide
infrastructure that can be extended to add this capability later.

Changes from V1:
* Removed checks in find_frame_creation() that prevented location of the frame
  creation instruction in heavily optimized code
* Various formatting/commenting/file location tweaks per review comments
* Dropped Kconfig option to enable STACKTRACE as something logically separate
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>

Allow developer to configure memory page size at compile time.
Larger pages can improve performance on some workloads.

Based on PowerPC code.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>

Add trace_hardirqs_off and trace_hardirqs_on to do_IRQ function.
Signed-off-by: Michal Simek <monstr@monstr.eu>

sys_clone syscall ignored args which this patch mapped to args
which are passing from glibc.

Here is the origin problem description.

"I ran the static libgcc tests (very few of them are there, they are
mostly dynamically linked) and some of  them fail with an assertion in
fork() system call (tid != pid), I looked at the microblaze/entry.S
file and it looks suspicious (ignores arguments 3-5)"

Arg mapping should be:
glibc ARCH_FORK(...) -> do_fork(...)
r5 -> r5   (clone_flags)
r6  -> r6 (stack_start, use parent->stack if NULL)
pt_regs -> r7 (pt_regs)
r7 -> r8 (stack_size)
r8 -> r9 (parent_tidptr)
r9 -> r10 (child_tidptr)
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>

Microblaze doesn't support frame pointers. Ftrace code
uses CALLER_ADDR1 which is defined in linux/ftrace.h. For Microblaze
is 0.
Signed-off-by: Michal Simek <monstr@monstr.eu>

copy_to_user_page macro is used in mm/memory.c:access_process_vm
function. This function is called from ptrace code (POKETEXT, POKEDATA)
which write data to memory. Microblaze handle physical address for
caches that's why there is virt_to_phys conversion.

There is potential one location which can caused the problem on WB system.

The important is take a look at write PTRACEs requests
(POKE/TEXT, DATA, USR).

Note:
Majority of Microblaze PTRACE code is moved to generic location
in newer kernel version that's why this solution should work on
the newest kernel version too.

linux/io.h is in cacheflush because of mm/nommu.c

Tested on a WB system - hello world debugging.
Signed-off-by: Michal Simek <monstr@monstr.eu>

Both versions can use the same node to register NODE_DATA(0)
Signed-off-by: Michal Simek <monstr@monstr.eu>

The label should be remove by
21e1c936

Warning message:
arch/microblaze/mm/fault.c: In function 'do_page_fault':
arch/microblaze/mm/fault.c:229: warning: label 'survive' defined but not used
Signed-off-by: Michal Simek <monstr@monstr.eu>

flush_dcache_page macro is necessary to implement for
JFFS2 rootfs support on WB system.
Signed-off-by: Michal Simek <monstr@monstr.eu>

There is wrong comment for TLB. Early printk uartlite
console uses TLB 63.
Signed-off-by: Michal Simek <monstr@monstr.eu>

__copy_to/from_user_inatomic should call __copy_to/from_user
because there is not necessary to check access because of kernel function.

might_sleep in copy_to/from_user macros is causing problems
in debug sessions too (CONFIG_DEBUG_SPINLOCK_SLEEP).

BUG: sleeping function called from invalid context at
.../arch/microblaze/include/asm/uaccess.h:388
in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: swapper
1 lock held by swapper/1:
 #0:  (&p->cred_guard_mutex){......}, at: [<c00d4b90>] prepare_bprm_creds+0x2c/0x88
Kernel Stack:
...

Call Trace:
[<c0006bd4>] microblaze_unwind+0x7c/0x94
[<c0006684>] show_stack+0xf4/0x190
[<c0006730>] dump_stack+0x10/0x30
[<c00103a0>] __might_sleep+0x12c/0x160
[<c0090de4>] file_read_actor+0x1d8/0x2a8
[<c0091568>] generic_file_aio_read+0x6b4/0xa64
[<c00cd778>] do_sync_read+0xac/0x110
[<c00ce254>] vfs_read+0xc8/0x160
[<c00d585c>] kernel_read+0x38/0x64
[<c00d5984>] prepare_binprm+0xfc/0x130
[<c00d6430>] do_execve+0x228/0x370
[<c000614c>] microblaze_execve+0x58/0xa4

caused by file_read_actor (mm/filemap.c) which calls
__copy_to_user_inatomic.
Signed-off-by: Michal Simek <monstr@monstr.eu>

nfs_commit_inode() needs to be defined irrespectively of whether or not
we are supporting NFSv3 and NFSv4.

Allow the compiler to optimise away code in the NFSv2-only case by
converting it into an inlined stub function.
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  cyber2000fb: fix console in truecolor modes
  cyber2000fb: fix machine hang on module load
  SA1111: Eliminate use after free
  ARM: Fix Versatile/Realview/VExpress MMC card detection sense
  ARM: 6279/1: highmem: fix SMP preemption bug in kmap_high_l1_vipt
  ARM: Add barriers to io{read,write}{8,16,32} accessors as well
  ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE
  ARM: 6272/1: Convert L2x0 to use the IO relaxed operations
  ARM: 6271/1: Introduce *_relaxed() I/O accessors
  ARM: 6275/1: ux500: don't use writeb() in uncompress.h
  ARM: 6270/1: clean files in arch/arm/boot/compressed/
  ARM: Fix csum_partial_copy_from_user()

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Ensure that writepage respects the nonblock flag
  NFS: kswapd must not block in nfs_release_page
  nfs: include space for the NUL in root path

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/edid: Fix the HDTV hack sync adjustment
  drm/radeon/kms: fix radeon mid power profile reporting

Debian's ia64 autobuilders have been seeing kernel freeze or reboot
when running the gdb testsuite (Debian bug 588574): dannf bisected to
2.6.32 62eede62 "mm: ZERO_PAGE without
PTE_SPECIAL"; and reproduced it with gdb's gcore on a simple target.

I'd missed updating the gate_vma handling in __get_user_pages(): that
happens to use vm_normal_page() (nowadays failing on the zero page),
yet reported success even when it failed to get a page - boom when
access_process_vm() tried to copy that to its intermediate buffer.

Fix this, resisting cleanups: in particular, leave it for now reporting
success when not asked to get any pages - very probably safe to change,
but let's not risk it without testing exposure.

Why did ia64 crash with 16kB pages, but succeed with 64kB pages?
Because setup_gate() pads each 64kB of its gate area with zero pages.
Reported-by: Andreas Barth <aba@not.so.argh.org>
Bisected-by: dann frazier <dannf@debian.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: dann frazier <dannf@dannf.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove the __exit mark from cifs_exit_dns_resolver() as it's called by the
module init routine in case of error, and so may have been discarded during
linkage.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Return value was not set to 0 in setcolreg() with truecolor modes. This causes
fb_set_cmap() to abort after first color, resulting in blank palette - and
blank console in 24bpp and 32bpp modes.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

I was testing two CyberPro 2000 based PCI cards on x86 and the machine always
hanged completely when the cyber2000fb module was loaded. It seems that the
card hangs when some registers are accessed too quickly after writing RAMDAC
control register. With this patch, both card work.

Add delay after RAMDAC control register write to prevent hangs on module load.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

__sa1111_remove always frees its argument, so the subsequent reference to
sachip->saved_state represents a use after free.  __sa1111_remove does not
appear to use the saved_state field, so the patch simply frees it first.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E,E2;
@@

__sa1111_remove(E)
...
(
  E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The MMC card detection sense has become really confused with negations
at various levels, leading to some platforms not detecting inserted
cards.  Fix this by converting everything to positive logic throughout,
thereby getting rid of these negations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

smp_processor_id() must not be called from a preemptible context (this
is checked by CONFIG_DEBUG_PREEMPT).  kmap_high_l1_vipt() was doing so.
This lead to a problem where the wrong per_cpu kmap_high_l1_vipt_depth
could be incremented, causing a BUG_ON(*depth <= 0); in
kunmap_high_l1_vipt().

The solution is to move the call to smp_processor_id() after the call
to preempt_disable().

Originally by: Andrew Howe <ahowe@nvidia.com>
Signed-off-by: Gary King <gking@nvidia.com>
Acked-by: Nicolas Pitre <nico.as.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

See https://bugzilla.kernel.org/show_bug.cgi?id=16056

If other processes are blocked waiting for kswapd to free up some memory so
that they can make progress, then we cannot allow kswapd to block on those
processes.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org

In root_nfs_name() it does the following:

        if (strlen(buf) + strlen(cp) > NFS_MAXPATHLEN) {
                printk(KERN_ERR "Root-NFS: Pathname for remote directory too long.\n");
                return -1;
        }
        sprintf(nfs_export_path, buf, cp);

In the original code if (strlen(buf) + strlen(cp) == NFS_MAXPATHLEN)
then the sprintf() would lead to an overflow.  Generally the rest of the
code assumes that the path can have NFS_MAXPATHLEN (1024) characters and
a NUL terminator so the fix is to add space to the nfs_export_path[]
buffer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>