- 25 Aug, 2017 13 commits
-
-
Andy Lutomirski authored
commit e93c1730 upstream. This closes a hole in our SMAP implementation. This patch comes from grsecurity. Good catch! Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/314cc9f294e8f14ed85485727556ad4f15bb1659.1502159503.git.luto@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Roger Pau Monne authored
commit 462cdace upstream. The current test for bio vec merging is not fully accurate and can be tricked into merging bios when certain grant combinations are used. The result of these malicious bio merges is a bio that extends past the memory page used by any of the originating bios. Take into account the following scenario, where a guest creates two grant references that point to the same mfn, ie: grant 1 -> mfn A, grant 2 -> mfn A. These references are then used in a PV block request, and mapped by the backend domain, thus obtaining two different pfns that point to the same mfn, pfn B -> mfn A, pfn C -> mfn A. If those grants happen to be used in two consecutive sectors of a disk IO operation becoming two different bios in the backend domain, the checks in xen_biovec_phys_mergeable will succeed, because bfn1 == bfn2 (they both point to the same mfn). However due to the bio merging, the backend domain will end up with a bio that expands past mfn A into mfn A + 1. Fix this by making sure the check in xen_biovec_phys_mergeable takes into account the offset and the length of the bio, this basically replicates whats done in __BIOVEC_PHYS_MERGEABLE using mfns (bus addresses). While there also remove the usage of __BIOVEC_PHYS_MERGEABLE, since that's already checked by the callers of xen_biovec_phys_mergeable. Reported-by:
"Jan H. Schönherr" <jschoenh@amazon.de> Signed-off-by:
Roger Pau Monné <roger.pau@citrix.com> Reviewed-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Kees Cook authored
commit c715b72c upstream. Moving the x86_64 and arm64 PIE base from 0x555555554000 to 0x000100000000 broke AddressSanitizer. This is a partial revert of: eab09532 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE") 02445990 ("arm64: move ELF_ET_DYN_BASE to 4GB / 4MB") The AddressSanitizer tool has hard-coded expectations about where executable mappings are loaded. The motivation for changing the PIE base in the above commits was to avoid the Stack-Clash CVEs that allowed executable mappings to get too close to heap and stack. This was mainly a problem on 32-bit, but the 64-bit bases were moved too, in an effort to proactively protect those systems (proofs of concept do exist that show 64-bit collisions, but other recent changes to fix stack accounting and setuid behaviors will minimize the impact). The new 32-bit PIE base is fine for ASan (since it matches the ET_EXEC base), so only the 64-bit PIE base needs to be reverted to let x86 and arm64 ASan binaries run again. Future changes to the 64-bit PIE base on these architectures can be made optional once a more dynamic method for dealing with AddressSanitizer is found. (e.g. always loading PIE into the mmap region for marked binaries.) Link: http://lkml.kernel.org/r/20170807201542.GA21271@beast Fixes: eab09532 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE") Fixes: 02445990 ("arm64: move ELF_ET_DYN_BASE to 4GB / 4MB") Signed-off-by:
Kees Cook <keescook@chromium.org> Reported-by:
Kostya Serebryany <kcc@google.com> Acked-by:
Will Deacon <will.deacon@arm.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
zhong jiang authored
commit 73223e4e upstream. I hit a use after free issue when executing trinity and repoduced it with KASAN enabled. The related call trace is as follows. BUG: KASan: use after free in SyS_get_mempolicy+0x3c8/0x960 at addr ffff8801f582d766 Read of size 2 by task syz-executor1/798 INFO: Allocated in mpol_new.part.2+0x74/0x160 age=3 cpu=1 pid=799 __slab_alloc+0x768/0x970 kmem_cache_alloc+0x2e7/0x450 mpol_new.part.2+0x74/0x160 mpol_new+0x66/0x80 SyS_mbind+0x267/0x9f0 system_call_fastpath+0x16/0x1b INFO: Freed in __mpol_put+0x2b/0x40 age=4 cpu=1 pid=799 __slab_free+0x495/0x8e0 kmem_cache_free+0x2f3/0x4c0 __mpol_put+0x2b/0x40 SyS_mbind+0x383/0x9f0 system_call_fastpath+0x16/0x1b INFO: Slab 0xffffea0009cb8dc0 objects=23 used=8 fp=0xffff8801f582de40 flags=0x200000000004080 INFO: Object 0xffff8801f582d760 @offset=5984 fp=0xffff8801f582d600 Bytes b4 ffff8801f582d750: ae 01 ff ff 00 00 00 00 5a 5a 5a 5a 5a 5a 5a 5a ........ZZZZZZZZ Object ffff8801f582d760: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ffff8801f582d770: 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkk. Redzone ffff8801f582d778: bb bb bb bb bb bb bb bb ........ Padding ffff8801f582d8b8: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ Memory state around the buggy address: ffff8801f582d600: fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8801f582d680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff8801f582d700: fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb fc !shared memory policy is not protected against parallel removal by other thread which is normally protected by the mmap_sem. do_get_mempolicy, however, drops the lock midway while we can still access it later. Early premature up_read is a historical artifact from times when put_user was called in this path see https://lwn.net/Articles/124754/ but that is gone since 8bccd85f ("[PATCH] Implement sys_* do_* layering in the memory policy layer."). but when we have the the current mempolicy ref count model. The issue was introduced accordingly. Fix the issue by removing the premature release. Link: http://lkml.kernel.org/r/1502950924-27521-1-git-send-email-zhongjiang@huawei.comSigned-off-by:
zhong jiang <zhongjiang@huawei.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by:
-
Takashi Iwai authored
commit 0f174b35 upstream. C-Media devices (at least some models) mute the playback stream when volumes are set to the minimum value. But this isn't informed via TLV and the user-space, typically PulseAudio, gets confused as if it's still played in a low volume. This patch adds the new flag, min_mute, to struct usb_mixer_elem_info for indicating that the mixer element is with the minimum-mute volume. This flag is set for known C-Media devices in snd_usb_mixer_fu_apply_quirk() in turn. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196669Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit a8e800fe upstream. A Senheisser headset requires the typical sample-rate quirk for avoiding spurious errors from inquiring the current sample rate like: usb 1-1: 2:1: cannot get freq at ep 0x4 usb 1-1: 3:1: cannot get freq at ep 0x83 The USB ID 1395:740a has to be added to the entries in snd_usb_get_sample_rate_quirk(). Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1052580Signed-off-by:
-
Daniel Mentz authored
commit 7e1d90f6 upstream. commit 4842e98f ("ALSA: seq: Fix race at creating a queue") attempted to fix a race reported by syzkaller. That fix has been described as follows: " When a sequencer queue is created in snd_seq_queue_alloc(),it adds the new queue element to the public list before referencing it. Thus the queue might be deleted before the call of snd_seq_queue_use(), and it results in the use-after-free error, as spotted by syzkaller. The fix is to reference the queue object at the right time. " Even with that fix in place, syzkaller reported a use-after-free error. It specifically pointed to the last instruction "return q->queue" in snd_seq_queue_alloc(). The pointer q is being used after kfree() has been called on it. It turned out that there is still a small window where a race can happen. The window opens at snd_seq_ioctl_create_queue()->snd_seq_queue_alloc()->queue_list_add() and closes at snd_seq_ioctl_create_queue()->queueptr()->snd_use_lock_use(). Between these two calls, a different thread could delete the queue and possibly re-create a different queue in the same location in queue_list. This change prevents this situation by calling snd_use_lock_use() from snd_seq_queue_alloc() prior to calling queue_list_add(). It is then the caller's responsibility to call snd_use_lock_free(&q->use_lock). Fixes: 4842e98f ("ALSA: seq: Fix race at creating a queue") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Daniel Mentz <danielmentz@google.com> Signed-off-by:
-
KT Liao authored
commit 76988690 upstream. Add 2 new IDs (ELAN0609 and ELAN060B) to the list of ACPI IDs that should be handled by the driver. Signed-off-by:
KT Liao <kt.liao@emc.com.tw> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Kai-Heng Feng authored
commit 1874064e upstream. Similar to commit 722c5ac7 ("Input: elan_i2c - add ELAN0605 to the ACPI table"), ELAN0608 should be handled by elan_i2c. This touchpad can be found in Lenovo ideapad 320-14IKB. BugLink: https://bugs.launchpad.net/bugs/1708852Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
megha.dey@linux.intel.com authored
commit 8861249c upstream. It was reported that the sha1 AVX2 function(sha1_transform_avx2) is reading ahead beyond its intended data, and causing a crash if the next block is beyond page boundary: http://marc.info/?l=linux-crypto-vger&m=149373371023377 This patch makes sure that there is no overflow for any buffer length. It passes the tests written by Jan Stancek that revealed this problem: https://github.com/jstancek/sha1-avx2-crash I have re-enabled sha1-avx2 by reverting commit b82ce244 Fixes: b82ce244 ("crypto: sha1-ssse3 - Disable avx2") Originally-by:
Ilya Albrekht <ilya.albrekht@intel.com> Tested-by:
Jan Stancek <jstancek@redhat.com> Signed-off-by:
Megha Dey <megha.dey@linux.intel.com> Reported-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Thomas Bogendoerfer authored
commit 40981160 upstream. For 64bit kernels the lmmio_space_offset of the host bridge window isn't set correctly on systems with dino/cujo PCI host bridges. This leads to not assigned memory bars and failing drivers, which need to use these bars. Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> Acked-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Jan Kara authored
commit d76036ab upstream. audit_remove_watch_rule() drops watch's reference to parent but then continues to work with it. That is not safe as parent can get freed once we drop our reference. The following is a trivial reproducer: mount -o loop image /mnt touch /mnt/file auditctl -w /mnt/file -p wax umount /mnt auditctl -D <crash in fsnotify_destroy_mark()> Grab our own reference in audit_remove_watch_rule() earlier to make sure mark does not get freed under us. Reported-by:
Tony Jones <tonyj@suse.de> Signed-off-by:
Jan Kara <jack@suse.cz> Tested-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Liping Zhang authored
commit 9c3f3794 upstream. If one cpu is doing nf_ct_extend_unregister while another cpu is doing __nf_ct_ext_add_length, then we may hit BUG_ON(t == NULL). Moreover, there's no synchronize_rcu invocation after set nf_ct_ext_types[id] to NULL, so it's possible that we may access invalid pointer. But actually, most of the ct extends are built-in, so the problem listed above will not happen. However, there are two exceptions: NF_CT_EXT_NAT and NF_CT_EXT_SYNPROXY. For _EXT_NAT, the panic will not happen, since adding the nat extend and unregistering the nat extend are located in the same file(nf_nat_core.c), this means that after the nat module is removed, we cannot add the nat extend too. For _EXT_SYNPROXY, synproxy extend may be added by init_conntrack, while synproxy extend unregister will be done by synproxy_core_exit. So after nf_synproxy_core.ko is removed, we may still try to add the synproxy extend, then kernel panic may happen. I know it's very hard to reproduce this issue, but I can play a tricky game to make it happen very easily :) Step 1. Enable SYNPROXY for tcp dport 1234 at FORWARD hook: # iptables -I FORWARD -p tcp --dport 1234 -j SYNPROXY Step 2. Queue the syn packet to the userspace at raw table OUTPUT hook. Also note, in the userspace we only add a 20s' delay, then reinject the syn packet to the kernel: # iptables -t raw -I OUTPUT -p tcp --syn -j NFQUEUE --queue-num 1 Step 3. Using "nc 2.2.2.2 1234" to connect the server. Step 4. Now remove the nf_synproxy_core.ko quickly: # iptables -F FORWARD # rmmod ipt_SYNPROXY # rmmod nf_synproxy_core Step 5. After 20s' delay, the syn packet is reinjected to the kernel. Now you will see the panic like this: kernel BUG at net/netfilter/nf_conntrack_extend.c:91! Call Trace: ? __nf_ct_ext_add_length+0x53/0x3c0 [nf_conntrack] init_conntrack+0x12b/0x600 [nf_conntrack] nf_conntrack_in+0x4cc/0x580 [nf_conntrack] ipv4_conntrack_local+0x48/0x50 [nf_conntrack_ipv4] nf_reinject+0x104/0x270 nfqnl_recv_verdict+0x3e1/0x5f9 [nfnetlink_queue] ? nfqnl_recv_verdict+0x5/0x5f9 [nfnetlink_queue] ? nla_parse+0xa0/0x100 nfnetlink_rcv_msg+0x175/0x6a9 [nfnetlink] [...] One possible solution is to make NF_CT_EXT_SYNPROXY extend built-in, i.e. introduce nf_conntrack_synproxy.c and only do ct extend register and unregister in it, similar to nf_conntrack_timeout.c. But having such a obscure restriction of nf_ct_extend_unregister is not a good idea, so we should invoke synchronize_rcu after set nf_ct_ext_types to NULL, and check the NULL pointer when do __nf_ct_ext_add_length. Then it will be easier if we add new ct extend in the future. Last, we use kfree_rcu to free nf_ct_ext, so rcu_barrier() is unnecessary anymore, remove it too. Signed-off-by:
Liping Zhang <zlpnobody@gmail.com> Acked-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Cc: Stefan Bader <stefan.bader@canonical.com> Signed-off-by:
-
- 16 Aug, 2017 24 commits
-
-
Greg Kroah-Hartman authored
-
Thomas Gleixner authored
commit 3fa53ec2 upstream. The irq chip callbacks irq_request/release_resources() have absolutely no business with masking and unmasking the irq. The core code unmasks the interrupt after complete setup and masks it before invoking irq_release_resources(). The unmask is actually harmful as it happens before the interrupt is completely initialized in __setup_irq(). Remove it. Fixes: f6a8249f ("pinctrl: exynos: Lock GPIOs as interrupts when used as EINTs") Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Kukjin Kim <kgene@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-samsung-soc@vger.kernel.org Cc: linux-gpio@vger.kernel.org Acked-by:
Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Icenowy Zheng authored
commit d81ece74 upstream. The PH16 pin has a function with mux id 0x5, which is the DET pin of the "sim" (smart card reader) IP block. This function is missing in old versions of A10/A20 SoCs' datasheets and user manuals, so it's also missing in the old drivers. The newest A10 Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and it's discovered during implementing R40 pinctrl driver. Add it to the driver. As we now merged A20 pinctrl driver to the A10 one, we need to only fix the A10 driver now. Fixes: f2821b1c ("pinctrl: sunxi: Move Allwinner A10 pinctrl driver to a driver of its own") Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Reviewed-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Christoph Hellwig authored
commit 8a9d6e96 upstream. The blocklayout code does not compile cleanly for a 32-bit sector_t, and also has no reliable checks for devices sizes, which makes it unsafe to use with a kernel that doesn't support large block devices. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reported-by:
Arnd Bergmann <arnd@arndb.de> Fixes: 5c83746a ("pnfs/blocklayout: in-kernel GETDEVICEINFO XDR parsing") Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Stefan-Gabriel Mirea authored
commit d466d3c1 upstream. In order to select the alternate voltage reference pair (VALTH/VALTL), the right value for the REFSEL field in the ADCx_CFG register is "01", leading to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1]. [1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf Fixes: a7754276 ("iio:adc:imx: add Freescale Vybrid vf610 adc driver") Signed-off-by:
Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Sandeep Singh authored
commit e788787e upstream. Certain HP keyboards would keep inputting a character automatically which is the wake-up key after S3 resume On some AMD platforms USB host fails to respond (by holding resume-K) to USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures that resume is signaled for at least 20 ms (TDRSMDN), which is defined in USB 2.0 spec. The result is that the keyboard is out of function. In SNPS USB design, the host responds to the resume request only after system gets back to S0 and the host gets to functional after the internal HW restore operation that is more than 1 second after the initial resume request from the USB device. As a workaround for specific keyboard ID(HP Keyboards), applying port reset after resume when the keyboard is plugged in. Signed-off-by:
Sandeep Singh <Sandeep.Singh@amd.com> Signed-off-by:
Shyam Sundar S K <Shyam-sundar.S-k@amd.com> cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Reviewed-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Kai-Heng Feng authored
commit 7496cfe5 upstream. Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to connect to Realtek r8153. The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk can make it work. Since another r8153 dongle at my hand does not have the issue, so add the quirk to the Genesys Logic hub instead. Signed-off-by:
-
Bin Liu authored
commit 2eac1362 upstream. While unlink an urb, if the urb has been programmed in the controller, the controller driver might do some hw related actions to tear down the urb. Currently usb_hcd_flush_endpoint() passes each urb from the head of the endpoint's urb_list to the controller driver, which could make the controller driver think each urb has been programmed and take the unnecessary actions for each urb. This patch changes the behavior in usb_hcd_flush_endpoint() to pass the urbs from the tail of the list, to avoid any unnecessary actions in an controller driver. Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Alan Stern authored
commit 94c43b98 upstream. Some buggy USB disk adapters disconnect and reconnect multiple times during the enumeration procedure. This may lead to a device connecting at full speed instead of high speed, because when the USB stack sees that a device isn't able to enumerate at high speed, it tries to hand the connection over to a full-speed companion controller. The logic for doing this is careful to check that the device is still connected. But this check is inadequate if the device disconnects and reconnects before the check is done. The symptom is that a device works, but much more slowly than it is capable of operating. The situation was made worse recently by commit 22547c4c ("usb: hub: Wait for connection to be reestablished after port reset"), which increases the delay following a reset before a disconnect is recognized, thus giving the device more time to reconnect. This patch makes the check more robust. If the device was disconnected at any time during enumeration, we will now skip the full-speed handover. Signed-off-by:
Zdenek Kabelac <zkabelac@redhat.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Alan Swanson authored
commit 89f23d51 upstream. Similar to commit d595259f ("usb-storage: Add ignore-residue quirk for Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already present in unusual_uas.h. Both in same controller IC family. Issue is that MakeMKV fails during key exchange with installed bluray drive with following error: 002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED' occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0' Signed-off-by:
Alan Swanson <reiver@improbability.net> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Akinobu Mita authored
commit a3507e48 upstream. The TSL2563 driver provides three iio channels, two of which are raw ADC channels (channel 0 and channel 1) in the device and the remaining one is calculated by the two. The ADC channel 0 only supports programmable interrupt with threshold settings and this driver supports the event but the generated event code does not contain the corresponding iio channel type. This is going to change userspace ABI. Hopefully fixing this to be what it should always have been won't break any userspace code. Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Hans de Goede authored
commit e59e1898 upstream. After probe we would put the device in normal mode, after a runtime suspend-resume we would put it back in normal mode. But for a regular suspend-resume we would only put it back in normal mode if triggers or events have been requested. This is not consistent and breaks reading raw values after a suspend-resume. This commit changes the regular resume path to also unconditionally put the device back in normal mode, fixing reading of raw values not working after a regular suspend-resume cycle. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Arnd Bergmann authored
commit 105967ad upstream. gcc-7 points out an older regression: drivers/staging/iio/resolver/ad2s1210.c: In function 'ad2s1210_read_raw': drivers/staging/iio/resolver/ad2s1210.c:515:42: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context] The original code had 'unsigned short' here, but incorrectly got converted to 'bool'. This reverts the regression and uses a normal type instead. Fixes: 29148543 ("staging:iio:resolver:ad2s1210 minimal chan spec conversion.") Signed-off-by:
-
Rafael J. Wysocki authored
commit cd5a6a4f upstream. Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for the primary one. Among other thigs, this prevents check_root_hub_suspended() from returning -EBUSY for dead HCDs which helps to work around system suspend issues in some situations. This actually fixes occasional suspend failures on one of my test machines. Suggested-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by:
-
Bin Liu authored
commit 45d73860 upstream. commit 68fe05e2 ("usb: musb: fix tx fifo flush handling") drops the 1ms delay trying to solve the long disconnect time issue when application queued many tx urbs. However, the 1ms delay is needed for some use cases, for example, without the delay, reconnecting AR9271 WIFI dongle no longer works if the connection is dropped from the AP. So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the long disconnect time problem with a separate patch for usb_hcd_flush_endpoint(). Signed-off-by:
-
Greg Kroah-Hartman authored
commit 3b6bcd3d upstream. This adds a new ATEN device id for a new pl2303-based device. Reported-by:
Peter Kuo <PeterKuo@aten.com.tw> Cc: Johan Hovold <johan@kernel.org> Signed-off-by:
-
Stefan Triller authored
commit 9585e340 upstream. The German Telekom offers a ZigBee USB Stick under the brand name Qivicon for their SmartHome Home Base in its 1. Generation. The productId is not known by the according kernel module, this patch adds support for it. Signed-off-by:
Stefan Triller <github@stefantriller.de> Reviewed-by:
Frans Klaver <fransklaver@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Hector Martin authored
commit fd1b8668 upstream. Add device id for D-Link DWM-222. Signed-off-by:
Hector Martin <marcan@marcan.st> Signed-off-by:
-
Weston Andros Adamson authored
commit 1feb2616 upstream. The client was freeing the nfs4_ff_layout_ds, but not the contained nfs4_ff_ds_version array. Signed-off-by:
Weston Andros Adamson <dros@primarydata.com> Signed-off-by:
-
Mateusz Jurczyk authored
commit 68227c03 upstream. Before the patch, the flock flag could remain uninitialized for the lifespan of the fuse_file allocation. Unless set to true in fuse_file_flock(), it would remain in an indeterminate state until read in an if statement in fuse_release_common(). This could consequently lead to taking an unexpected branch in the code. The bug was discovered by a runtime instrumentation designed to detect use of uninitialized memory in the kernel. Signed-off-by:
Mateusz Jurczyk <mjurczyk@google.com> Fixes: 37fb3a30 ("fuse: fix flock") Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 978d13d6 upstream. This patch fixes a bug associated with iscsit_reset_np_thread() that can occur during parallel configfs rmdir of a single iscsi_np used across multiple iscsi-target instances, that would result in hung task(s) similar to below where configfs rmdir process context was blocked indefinately waiting for iscsi_np->np_restart_comp to finish: [ 6726.112076] INFO: task dcp_proxy_node_:15550 blocked for more than 120 seconds. [ 6726.119440] Tainted: G W O 4.1.26-3321 #2 [ 6726.125045] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 6726.132927] dcp_proxy_node_ D ffff8803f202bc88 0 15550 1 0x00000000 [ 6726.140058] ffff8803f202bc88 ffff88085c64d960 ffff88083b3b1ad0 ffff88087fffeb08 [ 6726.147593] ffff8803f202c000 7fffffffffffffff ffff88083f459c28 ffff88083b3b1ad0 [ 6726.155132] ffff88035373c100 ffff8803f202bca8 ffffffff8168ced2 ffff8803f202bcb8 [ 6726.162667] Call Trace: [ 6726.165150] [<ffffffff8168ced2>] schedule+0x32/0x80 [ 6726.170156] [<ffffffff8168f5b4>] schedule_timeout+0x214/0x290 [ 6726.176030] [<ffffffff810caef2>] ? __send_signal+0x52/0x4a0 [ 6726.181728] [<ffffffff8168d7d6>] wait_for_completion+0x96/0x100 [ 6726.187774] [<ffffffff810e7c80>] ? wake_up_state+0x10/0x10 [ 6726.193395] [<ffffffffa035d6e2>] iscsit_reset_np_thread+0x62/0xe0 [iscsi_target_mod] [ 6726.201278] [<ffffffffa0355d86>] iscsit_tpg_disable_portal_group+0x96/0x190 [iscsi_target_mod] [ 6726.210033] [<ffffffffa0363f7f>] lio_target_tpg_store_enable+0x4f/0xc0 [iscsi_target_mod] [ 6726.218351] [<ffffffff81260c5a>] configfs_write_file+0xaa/0x110 [ 6726.224392] [<ffffffff811ea364>] vfs_write+0xa4/0x1b0 [ 6726.229576] [<ffffffff811eb111>] SyS_write+0x41/0xb0 [ 6726.234659] [<ffffffff8169042e>] system_call_fastpath+0x12/0x71 It would happen because each iscsit_reset_np_thread() sets state to ISCSI_NP_THREAD_RESET, sends SIGINT, and then blocks waiting for completion on iscsi_np->np_restart_comp. However, if iscsi_np was active processing a login request and more than a single iscsit_reset_np_thread() caller to the same iscsi_np was blocked on iscsi_np->np_restart_comp, iscsi_np kthread process context in __iscsi_target_login_thread() would flush pending signals and only perform a single completion of np->np_restart_comp before going back to sleep within transport specific iscsit_transport->iscsi_accept_np code. To address this bug, add a iscsi_np->np_reset_count and update __iscsi_target_login_thread() to keep completing np->np_restart_comp until ->np_reset_count has reached zero. Reported-by:
Gary Guo <ghg@datera.io> Tested-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Varun Prakash authored
commit ea8dc5b4 upstream. On receiving text request iscsi-target allocates buffer for payload in iscsit_handle_text_cmd() and assigns buffer pointer to cmd->text_in_ptr, this buffer is currently freed in iscsit_release_cmd(), if iscsi-target sets 'C' bit in text response then it will receive another text request from the initiator with ttt != 0xffffffff in this case iscsi-target will find cmd using itt and call iscsit_setup_text_cmd() which will set cmd->text_in_ptr to NULL without freeing previously allocated buffer. This patch fixes this issue by calling kfree(cmd->text_in_ptr) in iscsit_setup_text_cmd() before assigning NULL to it. For the first text request cmd->text_in_ptr is NULL as cmd is memset to 0 in iscsit_allocate_cmd(). Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Jonathan Toppins authored
commit 75dddef3 upstream. The RDMA subsystem can generate several thousand of these messages per second eventually leading to a kernel crash. Ratelimit these messages to prevent this crash. Doug said: "I've been carrying a version of this for several kernel versions. I don't remember when they started, but we have one (and only one) class of machines: Dell PE R730xd, that generate these errors. When it happens, without a rate limit, we get rcu timeouts and kernel oopses. With the rate limit, we just get a lot of annoying kernel messages but the machine continues on, recovers, and eventually the memory operations all succeed" And: "> Well... why are all these EBUSY's occurring? It sounds inefficient > (at least) but if it is expected, normal and unavoidable then > perhaps we should just remove that message altogether? I don't have an answer to that question. To be honest, I haven't looked real hard. We never had this at all, then it started out of the blue, but only on our Dell 730xd machines (and it hits all of them), but no other classes or brands of machines. And we have our 730xd machines loaded up with different brands and models of cards (for instance one dedicated to mlx4 hardware, one for qib, one for mlx5, an ocrdma/cxgb4 combo, etc), so the fact that it hit all of the machines meant it wasn't tied to any particular brand/model of RDMA hardware. To me, it always smelled of a hardware oddity specific to maybe the CPUs or mainboard chipsets in these machines, so given that I'm not an mm expert anyway, I never chased it down. A few other relevant details: it showed up somewhere around 4.8/4.9 or thereabouts. It never happened before, but the prinkt has been there since the 3.18 days, so possibly the test to trigger this message was changed, or something else in the allocator changed such that the situation started happening on these machines? And, like I said, it is specific to our 730xd machines (but they are all identical, so that could mean it's something like their specific ram configuration is causing the allocator to hit this on these machine but not on other machines in the cluster, I don't want to say it's necessarily the model of chipset or CPU, there are other bits of identicalness between these machines)" Link: http://lkml.kernel.org/r/499c0f6cc10d6eb829a67f2a4d75b4228a9b356e.1501695897.git.jtoppins@redhat.comSigned-off-by:
Jonathan Toppins <jtoppins@redhat.com> Reviewed-by:
Doug Ledford <dledford@redhat.com> Tested-by:
-
Dima Zavin authored
commit 89affbf5 upstream. In codepaths that use the begin/retry interface for reading mems_allowed_seq with irqs disabled, there exists a race condition that stalls the patch process after only modifying a subset of the static_branch call sites. This problem manifested itself as a deadlock in the slub allocator, inside get_any_partial. The loop reads mems_allowed_seq value (via read_mems_allowed_begin), performs the defrag operation, and then verifies the consistency of mem_allowed via the read_mems_allowed_retry and the cookie returned by xxx_begin. The issue here is that both begin and retry first check if cpusets are enabled via cpusets_enabled() static branch. This branch can be rewritted dynamically (via cpuset_inc) if a new cpuset is created. The x86 jump label code fully synchronizes across all CPUs for every entry it rewrites. If it rewrites only one of the callsites (specifically the one in read_mems_allowed_retry) and then waits for the smp_call_function(do_sync_core) to complete while a CPU is inside the begin/retry section with IRQs off and the mems_allowed value is changed, we can hang. This is because begin() will always return 0 (since it wasn't patched yet) while retry() will test the 0 against the actual value of the seq counter. The fix is to use two different static keys: one for begin (pre_enable_key) and one for retry (enable_key). In cpuset_inc(), we first bump the pre_enable key to ensure that cpuset_mems_allowed_begin() always return a valid seqcount if are enabling cpusets. Similarly, when disabling cpusets via cpuset_dec(), we first ensure that callers of cpuset_mems_allowed_retry() will start ignoring the seqcount value before we let cpuset_mems_allowed_begin() return 0. The relevant stack traces of the two stuck threads: CPU: 1 PID: 1415 Comm: mkdir Tainted: G L 4.9.36-00104-g540c51286237 #4 Hardware name: Default string Default string/Hardware, BIOS 4.29.1-20170526215256 05/26/2017 task: ffff8817f9c28000 task.stack: ffffc9000ffa4000 RIP: smp_call_function_many+0x1f9/0x260 Call Trace: smp_call_function+0x3b/0x70 on_each_cpu+0x2f/0x90 text_poke_bp+0x87/0xd0 arch_jump_label_transform+0x93/0x100 __jump_label_update+0x77/0x90 jump_label_update+0xaa/0xc0 static_key_slow_inc+0x9e/0xb0 cpuset_css_online+0x70/0x2e0 online_css+0x2c/0xa0 cgroup_apply_control_enable+0x27f/0x3d0 cgroup_mkdir+0x2b7/0x420 kernfs_iop_mkdir+0x5a/0x80 vfs_mkdir+0xf6/0x1a0 SyS_mkdir+0xb7/0xe0 entry_SYSCALL_64_fastpath+0x18/0xad ... CPU: 2 PID: 1 Comm: init Tainted: G L 4.9.36-00104-g540c51286237 #4 Hardware name: Default string Default string/Hardware, BIOS 4.29.1-20170526215256 05/26/2017 task: ffff8818087c0000 task.stack: ffffc90000030000 RIP: int3+0x39/0x70 Call Trace: <#DB> ? ___slab_alloc+0x28b/0x5a0 <EOE> ? copy_process.part.40+0xf7/0x1de0 __slab_alloc.isra.80+0x54/0x90 copy_process.part.40+0xf7/0x1de0 copy_process.part.40+0xf7/0x1de0 kmem_cache_alloc_node+0x8a/0x280 copy_process.part.40+0xf7/0x1de0 _do_fork+0xe7/0x6c0 _raw_spin_unlock_irq+0x2d/0x60 trace_hardirqs_on_caller+0x136/0x1d0 entry_SYSCALL_64_fastpath+0x5/0xad do_syscall_64+0x27/0x350 SyS_clone+0x19/0x20 do_syscall_64+0x60/0x350 entry_SYSCALL64_slow_path+0x25/0x25 Link: http://lkml.kernel.org/r/20170731040113.14197-1-dmitriyz@waymo.com Fixes: 46e700ab ("mm, page_alloc: remove unnecessary taking of a seqlock when cpusets are disabled") Signed-off-by:
Dima Zavin <dmitriyz@waymo.com> Reported-by:
Cliff Spradlin <cspradlin@waymo.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Christopher Lameter <cl@linux.com> Cc: Li Zefan <lizefan@huawei.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by:
-
- 13 Aug, 2017 3 commits
-
-
Greg Kroah-Hartman authored
-
Michal Kubeček authored
commit a5cb659b upstream. Our customer encountered stuck NFS writes for blocks starting at specific offsets w.r.t. page boundary caused by networking stack sending packets via UFO enabled device with wrong checksum. The problem can be reproduced by composing a long UDP datagram from multiple parts using MSG_MORE flag: sendto(sd, buff, 1000, MSG_MORE, ...); sendto(sd, buff, 1000, MSG_MORE, ...); sendto(sd, buff, 3000, 0, ...); Assume this packet is to be routed via a device with MTU 1500 and NETIF_F_UFO enabled. When second sendto() gets into __ip_append_data(), this condition is tested (among others) to decide whether to call ip_ufo_append_data(): ((length + fragheaderlen) > mtu) || (skb && skb_is_gso(skb)) At the moment, we already have skb with 1028 bytes of data which is not marked for GSO so that the test is false (fragheaderlen is usually 20). Thus we append second 1000 bytes to this skb without invoking UFO. Third sendto(), however, has sufficient length to trigger the UFO path so that we end up with non-UFO skb followed by a UFO one. Later on, udp_send_skb() uses udp_csum() to calculate the checksum but that assumes all fragments have correct checksum in skb->csum which is not true for UFO fragments. When checking against MTU, we need to add skb->len to length of new segment if we already have a partially filled skb and fragheaderlen only if there isn't one. In the IPv6 case, skb can only be null if this is the first segment so that we have to use headersize (length of the first IPv6 header) rather than fragheaderlen (length of IPv6 header of further fragments) for skb == NULL. Fixes: e89e9cf5 ("[IPv4/IPv6]: UFO Scatter-gather approach") Fixes: e4c5e13a ("ipv6: Should use consistent conditional judgement for ip6 fragment between __ip6_append_data and ip6_finish_output") Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Acked-by:
Vlad Yasevich <vyasevic@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
zheng li authored
ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output commit 0a28cfd5 upstream. There is an inconsistent conditional judgement in __ip_append_data and ip_finish_output functions, the variable length in __ip_append_data just include the length of application's payload and udp header, don't include the length of ip header, but in ip_finish_output use (skb->len > ip_skb_dst_mtu(skb)) as judgement, and skb->len include the length of ip header. That causes some particular application's udp payload whose length is between (MTU - IP Header) and MTU were fragmented by ip_fragment even though the rst->dev support UFO feature. Add the length of ip header to length in __ip_append_data to keep consistent conditional judgement as ip_finish_output for ip fragment. Signed-off-by:
Zheng Li <james.z.li@ericsson.com> Signed-off-by:
-
