Currently the tg3 driver leaves the speed and duplex fields
uninitialized in tg3_get_settings() if the device is not up.  This can
lead to some strange deductions in certain versions of ethtool.  When
the device is up and the link is down, the driver reports SPEED_INVALID
and DUPLEX_INVALID for these fields.  This patch makes the presentation
consistent by returning SPEED_INVALID and DUPLEX_INVALID when the device
has not been brought up as well.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 5714, 5715, and 5780 devices do not have a separate rx jumbo
producer ring.  This patch changes the code so that resources are not
allocated for it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

src_map is no longer used in tg3_alloc_rx_skb().  Remove it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds Energy Efficient Ethernet (EEE) support for the 5718
device ID and the 57765 B0 asic revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds clause 45 register access methods.  They will be used in
the following patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows the driver to disable the additional transmit rings
available on the 5717 and 5719 devices.  This is not strictly necessary,
but is done anyways for correctness.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

5718 B0 and 5719 devices will use a new selfboot firmware format.  This
patch adds code to detect the new format so that bootcode versions get
reported correctly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of fib_hash_lock rwlock.

The fn_zone hash table resize is the noticeable part of this patch.

I added a seqlock per fn_zone, so that readers can restart their lookup
in the (very rare) case a writer expanded the hash table.

Add rcu heads in fib_alias and fib_node, use call_rcu() to defer their
freeing, and use appropriate _rcu list manipulations.

Stress test (160.000.000 udp frames sent, IP route cache disabled to
mimic DDOS attack, FIB_HASH)

Before:
real	0m41.191s
user	0m13.137s
sys	8m55.241s

After:
real	0m38.091s
user	0m13.189s
sys	7m53.018s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

First step for RCU conversion of fib_hash :

struct fn_zone are created and never deleted.

Very classic conversion, using rcu_assign_pointer(), rcu_dereference()
and rtnl_dereference() verbs.

__rcu markers on fz_next and fn_zone_list

They are created under RTNL, we dont need fib_hash_lock anymore in
fn_new_zone().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While looking for false sharing problems, I noticed
sizeof(struct fn_zone) was small (28 bytes) and possibly sharing a cache
line with an often written kernel structure.

Most of the time, fn_zone uses its initial hash table of 16 slots.

We can avoid the false sharing problem by embedding this initial hash
table in fn_zone itself, so that sizeof(fn_zone) > L1_CACHE_BYTES

We did a similar optimization in commit a6501e08 (Reduce memory needs
and speedup lookups)

Add a fz_revorder field to speedup fn_hash() a bit.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the standard macro to put this table in __devinitconst.

Compiled, untested.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a network bench, I noticed an unfortunate false sharing between
'loopback_dev' and 'count' fields in "struct net".

'count' is written each time a socket is created or destroyed, while
loopback_dev might be often read in routing code.

Move loopback_dev in a read mostly section of "struct net"

Note: struct netns_xfrm is cache line aligned on SMP.
(It contains a "struct dst_ops")
Move it at the end to avoid holes, and reduce sizeof(struct net) by 128
bytes on ia32.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As CWR is stronger than CA_Disorder state, we can miscount
SACK/Reno failure into other timeouts. Not a bad problem as
it can happen only due to ECN, FRTO detecting spurious RTO
or xmit error which are the only callers of tcp_enter_cwr.
And even then losses and RTO must still follow thereafter
to actually end up into the relevant code paths.

Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

When only fast rexmit should be done, tcp_mark_head_lost marks
L too far. Also, sacked_upto below 1 is perfectly valid number,
the packets == 0 then needs to be trapped elsewhere.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suppress a large block of warnings like:
drivers/net/niu.c:7094:38: warning: incorrect type in assignment (different base types)
drivers/net/niu.c:7094:38:    expected restricted __be32 [usertype] ip4src
drivers/net/niu.c:7094:38:    got unsigned long long
drivers/net/niu.c:7104:17: warning: cast from restricted __be32
...
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have USB, PCMCIA, and gigabit ethernet drivers that select
MII even though NET_ETHERNET is not enabled, so make MII not
be dependent on NET_ETHERNET.  It is still dependent on NET
and NETDEVICES.

Fixes kconfig unmet dependency warning (shortened, was very long string):

warning: (ARM_AT91_ETHER && NETDEVICES && NET_ETHERNET && ARM && ARCH_AT91RM9200 || ARM_KS8695_ETHER && NETDEVICES && NET_ETHERNET && ARM && ARCH_KS8695 || ... || IP1000 && NETDEVICES && NETDEV_1000 && PCI && EXPERIMENTAL || HAMACHI && NETDEVICES && NETDEV_1000 && PCI || R8169 && NETDEVICES && NETDEV_1000 && PCI || SIS190 && NETDEVICES && NETDEV_1000 && PCI || VIA_VELOCITY && NETDEVICES && NETDEV_1000 && PCI || ATL1 && NETDEVICES && NETDEV_1000 && PCI || ATL1E && NETDEVICES && NETDEV_1000 && PCI && EXPERIMENTAL || ATL1C && NETDEVICES && NETDEV_1000 && PCI && EXPERIMENTAL || JME && NETDEVICES && NETDEV_1000 && PCI || STMMAC_ETH && NETDEV_1000 && NETDEVICES && HAS_IOMEM || USB_PEGASUS && NETDEVICES && USB && NET || USB_RTL8150 && NETDEVICES && USB && NET && EXPERIMENTAL || USB_USBNET && NETDEVICES && USB && NET || PCMCIA_SMC91C92 && NETDEVICES && NET_PCMCIA && PCMCIA) selects MII which has unmet direct dependencies (NETDEVICES && NET_ETHERNET)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com> [2006-NOV-30]
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix kconfig dependency warning to satisfy dependencies:

warning: (MLX4_EN && NETDEVICES && NETDEV_10000 && PCI && INET || MLX4_INFINIBAND && INFINIBAND) selects MLX4_CORE which has unmet direct dependencies (NETDEVICES && NETDEV_10000 && PCI)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These tables only contain function pointers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do some cleanups of TIPC based on make namespacecheck
  1. Don't export unused symbols
  2. Eliminate dead code
  3. Make functions and variables local
  4. Rename buf_acquire to tipc_buf_acquire since it is used in several files

Compile tested only.
This make break out of tree kernel modules that depend on TIPC routines.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Full duplex only. Half duplex 1000 Mbps is not supported.
Signed-off-by: David Lv <DavidLv@viatech.com.cn>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Seguier Regis <rseguier@e-teleport.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

While doing profile analysis, I found fib_hash_table was sometime in a
cache line shared by a possibly often written kernel structure.

(CONFIG_IP_ROUTE_MULTIPATH || !CONFIG_IPV6_MULTIPLE_TABLES)

It's hard to detect because not easily reproductible.

Make sure we allocate a full cache line to keep this shared in all cpus
caches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib_table_lookup() might use fls() to speedup an open coded loop.

Noticed while doing a profile analysis.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib_nl_delrule() calls synchronize_rcu() for no apparent reason,
while rtnl is held.

I suspect it was done to avoid an atomic_inc_not_zero() in
fib_rules_lookup(), which commit 7fa7cb71 added anyway.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid two atomic ops on found rule in fib6_rule_lookup()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ethtool stats support.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There were no curly braces in this if condition so it always enabled full
duplex.

And ecmd->speed is an unsigned short so it is never equal to -1.  The
effect is that mii_ethtool_sset() fails with -EINVAL and an error is
printed to dmesg.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Their doesn't appear to be bugs with the endianness handling here, just get the
annotations right to keep sparse happy.

Suppresses the following sparse warnings:
drivers/net/dnet.c:30:5: warning: symbol 'dnet_readw_mac' was not declared. Should it be static?
drivers/net/dnet.c:49:6: warning: symbol 'dnet_writew_mac' was not declared. Should it be static?
drivers/net/dnet.c:364:5: warning: symbol 'dnet_phy_marvell_fixup' was not declared. Should it be static?
drivers/net/dnet.c:66:13: warning: incorrect type in assignment (different base types)
drivers/net/dnet.c:66:13:    expected unsigned short [unsigned] [usertype] tmp
drivers/net/dnet.c:66:13:    got restricted __be16 [usertype] <noident>
drivers/net/dnet.c:68:13: warning: incorrect type in assignment (different base types)
drivers/net/dnet.c:68:13:    expected unsigned short [unsigned] [usertype] tmp
drivers/net/dnet.c:68:13:    got restricted __be16 [usertype] <noident>
drivers/net/dnet.c:70:13: warning: incorrect type in assignment (different base types)
drivers/net/dnet.c:70:13:    expected unsigned short [unsigned] [usertype] tmp
drivers/net/dnet.c:70:13:    got restricted __be16 [usertype] <noident>
drivers/net/dnet.c:92:27: warning: cast to restricted __be16
drivers/net/dnet.c:94:33: warning: cast to restricted __be16
drivers/net/dnet.c:96:33: warning: cast to restricted __be16
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Single bit signed bitfields don't make a lot of sense, noticed by sparse:
drivers/net/cxgb4vf/t4vf_common.h:135:31: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:136:36: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:137:36: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:138:36: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:139:36: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:140:31: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:141:31: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:142:35: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:143:35: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:154:27: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:155:26: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:156:27: error: dubious one-bit signed bitfield
drivers/net/cxgb4vf/t4vf_common.h:157:26: error: dubious one-bit signed bitfield
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit b30973f8 (node-aware skb allocation) spread a wrong habit of
allocating net drivers skbs on a given memory node : The one closest to
the NIC hardware. This is wrong because as soon as we try to scale
network stack, we need to use many cpus to handle traffic and hit
slub/slab management on cross-node allocations/frees when these cpus
have to alloc/free skbs bound to a central node.

skb allocated in RX path are ephemeral, they have a very short
lifetime : Extra cost to maintain NUMA affinity is too expensive. What
appeared as a nice idea four years ago is in fact a bad one.

In 2010, NIC hardwares are multiqueue, or we use RPS to spread the load,
and two 10Gb NIC might deliver more than 28 million packets per second,
needing all the available cpus.

Cost of cross-node handling in network and vm stacks outperforms the
small benefit hardware had when doing its DMA transfert in its 'local'
memory node at RX time. Even trying to differentiate the two allocations
done for one skb (the sk_buff on local node, the data part on NIC
hardware node) is not enough to bring good performance.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using standard skb allocations in r8169 leads to order-3 allocations (if
PAGE_SIZE=4096), because NIC needs 16383 bytes, and skb overhead makes
this bigger than 16384 -> 32768 bytes per "skb"

Using kmalloc() permits to reduce memory requirements of one r8169 nic
by 4Mbytes. (256 frames * 16Kbytes). This is fine since a hardware bug
requires us to copy incoming frames, so we build real skb when doing
this copy.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove a DCB check config from DCB configuration we
continue to configure DCB even if it fails so don't
even bother to check.  Plus user space (lldpad) checks
this before programming the hw anyways.

Worse case is we program some values into the hw that
don't make total sense resulting in incorrect bandwidth
allocation.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following patch fixes warnings reported by `make namespacecheck`

Reported by Stephen Hemminger

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove functions that are declared, but not used in the driver.
This patch fixes warnings reported by `make namespacecheck`

Reported by Stephen Hemminger

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new interrupt ack functions and other hardware interface logic to
support the new device.

Update version to 2.2.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During cnic shutdown, the original driver code requires userspace to
close the uio device within a few seconds.  This doesn't always happen
as the userapp may be hung or otherwise take a long time to close.  The
system may crash when this happens.

We fix the problem by decoupling the uio structures from the cnic
structures during cnic shutdown.  We do not unregister the uio device
until the cnic driver is unloaded.  This eliminates the unreliable wait
loop for uio to close.

All uio structures are kept in a linked list.  If the device is shutdown
and later brought back up again, the uio strcture will be found in the
linked list and coupled back to the cnic structures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

and put all uio related structures and ring buffers in it.  This allows
uio operations to be done independent of the cnic device structures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

to free all UIO related structures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>