- 22 Jan, 2015 11 commits
-
-
Thomas Gleixner authored
enable_x2apic() is a convoluted unreadable mess because it is used for both enablement in early boot and for setup in cpu_init(). Split the code into x2apic_enable() for enablement and x2apic_setup() for setup of (secondary cpus). Make use of the new state tracking to simplify the logic. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Borislav Petkov <bp@alien8.de> Link: http://lkml.kernel.org/r/20150115211703.129287153@linutronix.deSigned-off-by:
-
Thomas Gleixner authored
There is no point in postponing the hardware disablement of x2apic. It can be disabled right away in the nox2apic setup function. Disable it right away and set the state to DISABLED . This allows to remove all the nox2apic conditionals all over the place. Signed-off-by:
-
Thomas Gleixner authored
Having 3 different variables to track the state is just silly and error prone. Add a proper state tracking variable which covers the three possible states: ON/OFF/DISABLED. We cannot use x2apic_mode for this as this would require to change all users of x2apic_mode with explicit comparisons for a state value instead of treating it as boolean. Signed-off-by:
Borislav Petkov <bp@alien8.de> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Tony Luck <tony.luck@intel.com> Link: http://lkml.kernel.org/r/20150115211702.955392443@linutronix.deSigned-off-by:
-
Thomas Gleixner authored
Rename the argument of try_to_enable_x2apic() so the purpose becomes more clear. Make the pr_warning more consistent and avoid the double print of "disabling". Signed-off-by:
-
Thomas Gleixner authored
No point in having try_to_enable_x2apic() outside of the CONFIG_X86_X2APIC section and having inline functions and more ifdefs to deal with it. Move the code into the existing ifdef section and remove the inline cruft. Fixup the printk about not enabling interrupt remapping as suggested by Boris. Signed-off-by:
-
Thomas Gleixner authored
No point in delaying the x2apic detection for the CONFIG_X86_X2APIC=n case to enable_IR_x2apic(). We rather detect that before we try to setup anything there. Signed-off-by:
-
Thomas Gleixner authored
If x2apic_preenabled is not enabled, then disable_x2apic() is not called from various places which results in x2apic_disabled not being set. So other code pathes can happily reenable the x2apic. Signed-off-by:
-
Thomas Gleixner authored
The x2apic_preenabled flag is just a horrible hack and if X2APIC support is disabled it does not reflect the actual hardware state. Check the hardware instead. Signed-off-by:
-
Thomas Gleixner authored
Having several disjunct pieces of code for x2apic support makes reading the code unnecessarily hard. Move it to one ifdeffed section. Signed-off-by:
-
Thomas Gleixner authored
No point in having a static variable around which is always 0. Let the compiler optimize code out if disabled. Signed-off-by:
-
Thomas Gleixner authored
enable_IR_x2apic() grew a open coded x2apic detection. Implement a proper helper function which shares the code with the already existing x2apic_enabled(). Made it use rdmsrl_safe as suggested by Boris. Signed-off-by:
-
- 15 Jan, 2015 18 commits
-
-
Jiang Liu authored
Refine code by normailizing the way to detect whether IR is enabled. Signed-off-by:
Jiang Liu <jiang.liu@linux.intel.com> Tested-by:
Joerg Roedel <joro@8bytes.org> Cc: Tony Luck <tony.luck@intel.com> Cc: iommu@lists.linux-foundation.org Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Link: http://lkml.kernel.org/r/1420615903-28253-17-git-send-email-jiang.liu@linux.intel.comSigned-off-by:
-
Jiang Liu authored
Change variable disable_irq_remap to be static and simplify the code. Signed-off-by:
-
Jiang Liu authored
Assign intel_irq_remap_ops to remap_ops only if intel_irq_remap_ops.prepare() succeeds. Signed-off-by:
-
Jiang Liu authored
Simplify irq_remapping code by killing irq_remapping_supported() and related interfaces. Joerg posted a similar patch at https://lkml.org/lkml/2014/12/15/490, so assume an signed-off from Joerg. Signed-off-by:
Joerg Roedel <jroedel@suse.de> Tested-by:
-
Joerg Roedel authored
This allows to get rid of the irq_remapping_supported() function and all its call-backs into the Intel and AMD IOMMU drivers. Signed-off-by:
-
Jiang Liu authored
When interrupt remapping hardware is not in X2APIC, CPU X2APIC mode will be disabled if: 1) Maximum CPU APIC ID is bigger than 255 2) hypervisior doesn't support x2apic mode. But we should only check whether hypervisor supports X2APIC mode when hypervisor(CONFIG_HYPERVISOR_GUEST) is enabled, otherwise X2APIC will always be disabled when CONFIG_HYPERVISOR_GUEST is disabled and IR doesn't work in X2APIC mode. Signed-off-by:
-
Jiang Liu authored
Currently if CPU supports X2APIC, IR hardware must work in X2APIC mode or disabled. Change the code to support IR working in XAPIC mode when CPU supports X2APIC. Then the CPU APIC driver will decide how to handle such as configuration by: 1) Disabling X2APIC mode 2) Forcing X2APIC physical mode This change also fixes a live locking when 1) BIOS enables CPU X2APIC 2) DMAR table disables X2APIC mode or IR hardware doesn't support X2APIC with following messages: [ 37.863463] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2 [ 37.863463] INTR-REMAP:[fault reason 36] Detected reserved fields in the IRTE entry [ 37.879372] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2 [ 37.879372] INTR-REMAP:[fault reason 36] Detected reserved fields in the IRTE entry [ 37.895282] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2 [ 37.895282] INTR-REMAP:[fault reason 36] Detected reserved fields in the IRTE entry [ 37.911192] dmar: INTR-REMAP: Request device [[f0:1f.7] fault index 2 Signed-off-by:
-
Joerg Roedel authored
IRQ remapping is only supported when all IOMMUs in the system support it. So check if all IOMMUs in the system support IRQ remapping before doing the allocations. [Jiang] 1) Rebased to v3.19. 2) Remove redundant check of ecap_ir_support(iommu->ecap) in function intel_enable_irq_remapping(). Signed-off-by:
-
Jiang Liu authored
Prepare for killing function irq_remapping_supported() by moving code from intel_irq_remapping_supported() into intel_prepare_irq_remapping(). Combined with patch from Joerg at https://lkml.org/lkml/2014/12/15/487, so assume an signed-off from Joerg. Signed-off-by:
-
Jiang Liu authored
If remapping is in XAPIC mode, the setup code just skips X2APIC initialization without checking max CPU APIC ID in system, which may cause problem if system has a CPU with APIC ID bigger than 255. Handle IR in XAPIC mode the same way as if remapping is disabled. [ tglx: Split out from previous patch ] Signed-off-by:
-
Jiang Liu authored
Refine enable_IR_x2apic() and related functions for better readability. [ tglx: Removed the XAPIC mode change and split it out into a seperate patch. Added comments. ] Signed-off-by:
-
Jiang Liu authored
X2APIC will be disabled if user specifies "nox2apic" on kernel command line, even when x2apic_preenabled is true. So correctly detect X2APIC status by using x2apic_enabled() instead of x2apic_preenabled. Signed-off-by:
-
Jiang Liu authored
Local variable x2apic_enabled has been assigned to but never referred, so kill it. Signed-off-by:
-
Jiang Liu authored
When kernel doesn't support X2APIC but BIOS has enabled X2APIC, system may panic or hang without useful messages. On the other hand, it's hard to dynamically disable X2APIC when CONFIG_X86_X2APIC is disabled. So panic with a clear message in such a case. Now system panics as below when X2APIC is disabled and interrupt remapping is enabled: [ 0.316118] LAPIC pending interrupts after 512 EOI [ 0.322126] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.368655] Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC [ 0.378300] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.18.0+ #340 [ 0.385300] Hardware name: Intel Corporation BRICKLAND/BRICKLAND, BIOS BRIVTIN1.86B.0051.L05.1406240953 06/24/2014 [ 0.396997] ffff88046dc03000 ffff88046c307dd8 ffffffff8179dada 00000000000043f2 [ 0.405629] ffffffff81a92158 ffff88046c307e58 ffffffff8179b757 0000000000000002 [ 0.414261] 0000000000000008 ffff88046c307e68 ffff88046c307e08 ffffffff813ad82b [ 0.422890] Call Trace: [ 0.425711] [<ffffffff8179dada>] dump_stack+0x45/0x57 [ 0.431533] [<ffffffff8179b757>] panic+0xc1/0x1f5 [ 0.436978] [<ffffffff813ad82b>] ? delay_tsc+0x3b/0x70 [ 0.442910] [<ffffffff8166fa2c>] panic_if_irq_remap+0x1c/0x20 [ 0.449524] [<ffffffff81d73645>] setup_IO_APIC+0x405/0x82e [ 0.464979] [<ffffffff81d6fcc2>] native_smp_prepare_cpus+0x2d9/0x31c [ 0.472274] [<ffffffff81d5d0ac>] kernel_init_freeable+0xd6/0x223 [ 0.479170] [<ffffffff81792ad0>] ? rest_init+0x80/0x80 [ 0.485099] [<ffffffff81792ade>] kernel_init+0xe/0xf0 [ 0.490932] [<ffffffff817a537c>] ret_from_fork+0x7c/0xb0 [ 0.497054] [<ffffffff81792ad0>] ? rest_init+0x80/0x80 [ 0.502983] ---[ end Kernel panic - not syncing: timer doesn't work through Interrupt-remapped IO-APIC System hangs as below when X2APIC and interrupt remapping are both disabled: [ 1.102782] pci 0000:00:02.0: System wakeup disabled by ACPI [ 1.109351] pci 0000:00:03.0: System wakeup disabled by ACPI [ 1.115915] pci 0000:00:03.2: System wakeup disabled by ACPI [ 1.122479] pci 0000:00:03.3: System wakeup disabled by ACPI [ 1.132274] pci 0000:00:1c.0: Enabling MPC IRBNCE [ 1.137620] pci 0000:00:1c.0: Intel PCH root port ACS workaround enabled [ 1.145239] pci 0000:00:1c.0: System wakeup disabled by ACPI [ 1.151790] pci 0000:00:1c.7: Enabling MPC IRBNCE [ 1.157128] pci 0000:00:1c.7: Intel PCH root port ACS workaround enabled [ 1.164748] pci 0000:00:1c.7: System wakeup disabled by ACPI [ 1.171447] pci 0000:00:1e.0: System wakeup disabled by ACPI [ 1.178612] acpiphp: Slot [8] registered [ 1.183095] pci 0000:00:02.0: PCI bridge to [bus 01] [ 1.188867] acpiphp: Slot [2] registered With this patch applied, the system panics in both cases with a proper panic message. Signed-off-by:
-
Thomas Gleixner authored
If x2apic got disabled on the kernel command line, then the following issue can happen: enable_IR_x2apic() .... x2apic_mode = 1; enable_x2apic(); if (x2apic_disabled) { __disable_x2apic(); return; } That leaves X2APIC disabled in hardware, but x2apic_mode stays 1. So all other code which checks x2apic_mode gets the wrong information. Set x2apic_mode to 0 after disabling it in hardware. This is just a hotfix. The proper solution is to rework this code so it has seperate functions for the initial setup on the boot processor and the secondary cpus, but that's beyond the scope of this fix. Signed-off-by: -
Thomas Gleixner authored
No reason anymore to do GFP_ATOMIC allocations which are not harmful in the normal bootup case, but matter in the physical hotplug scenario. Signed-off-by:
-
Thomas Gleixner authored
The whole iommu setup for irq remapping is a convoluted mess. The iommu detect function gets called from mem_init() and the prepare callback gets called from enable_IR_x2apic() for unknown reasons. Of course AMD and Intel setup differs in nonsensical ways. Intels prepare callback is explicit while AMDs prepare callback is implicit in setup_irq_remapping_ops() just to be called in the prepare call again. Because all of this gets called from enable_IR_x2apic() and the dmar prepare function merily parses the ACPI tables, but does not allocate memory we end up with memory allocation from irq disabled context later on. AMDs iommu code at least allocates the required memory from the prepare function. That has issues as well, but thats not scope of this patch. The goal of this change is to distangle the allocation from the actual enablement. There is no point to allocate memory from irq disabled regions with GFP_ATOMIC just because it does not matter at that point in the boot stage. It matters with physical hotplug later on. There is another issue with the current setup. Due to the conversion to stacked irqdomains we end up with a call into the irqdomain allocation code from irq disabled context, but that code does GFP_KERNEL allocations rightfully as there is no reason to do preperatory allocations with GFP_ATOMIC. That change caused the allocator code to complain about GFP_KERNEL allocations invoked in atomic context. Boris provided a temporary hackaround which changed the GFP flags if irq_domain_add() got called from atomic context. Not pretty and we really dont want to get this into a mainline release for obvious reasons. Move the ACPI table parsing and the resulting memory allocations from the enable to the prepare function. That allows to get rid of the horrible hackaround in irq_domain_add() later. [Jiang] Rebased onto v3.19 Signed-off-by:
-
Thomas Gleixner authored
enable_IR_x2apic() calls setup_irq_remapping_ops() which by default installs the intel dmar remapping ops and then calls the amd iommu irq remapping prepare callback to figure out whether we are running on an AMD machine with irq remapping hardware. Right after that it calls irq_remapping_prepare() which pointlessly checks: if (!remap_ops || !remap_ops->prepare) return -ENODEV; and then calls remap_ops->prepare() which is silly in the AMD case as it got called from setup_irq_remapping_ops() already a few microseconds ago. Simplify this and just collapse everything into irq_remapping_prepare(). The irq_remapping_prepare() remains still silly as it assigns blindly the intel ops, but that's not scope of this patch. The scope here is to move the preperatory work, i.e. memory allocations out of the atomic section which is required to enable irq remapping. Signed-off-by:
-
- 11 Jan, 2015 9 commits
-
-
Linus Torvalds authored
-
git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM fixes from Russell King: "Three small fixes from over the Christmas period, and wiring up the new execveat syscall for ARM" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region ARM: 8249/1: mm: dump: don't skip regions ARM: wire up execveat syscall
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Ingo Molnar: "Misc fixes: two vdso fixes, two kbuild fixes and a boot failure fix with certain odd memory mappings" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86, vdso: Use asm volatile in __getcpu x86/build: Clean auto-generated processor feature files x86: Fix mkcapflags.sh bash-ism x86: Fix step size adjustment during initial memory mapping x86_64, vdso: Fix the vdso address randomization algorithm
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fixes from Ingo Molnar: "Misc fixes: group scheduling corner case fix, two deadline scheduler fixes, effective_load() overflow fix, nested sleep fix, 6144 CPUs system fix" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group() sched/deadline: Avoid double-accounting in case of missed deadlines sched/deadline: Fix migration of SCHED_DEADLINE tasks sched: Fix odd values in effective_load() calculations sched, fanotify: Deal with nested sleeps sched: Fix KMALLOC_MAX_SIZE overflow during cpumask allocation
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Ingo Molnar: "Mostly tooling fixes, but also some kernel side fixes: uncore PMU driver fix, user regs sampling fix and an instruction decoder fix that unbreaks PEBS precise sampling" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes perf/x86_64: Improve user regs sampling perf: Move task_pt_regs sampling into arch code x86: Fix off-by-one in instruction decoder perf hists browser: Fix segfault when showing callchain perf callchain: Free callchains when hist entries are deleted perf hists: Fix children sort key behavior perf diff: Fix to sort by baseline field by default perf list: Fix --raw-dump option perf probe: Fix crash in dwarf_getcfi_elf perf probe: Fix to fall back to find probe point in symbols perf callchain: Append callchains only when requested perf ui/tui: Print backtrace symbols when segfault occurs perf report: Show progress bar for output resorting
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull locking fixes from Ingo Molnar: "A liblockdep fix and a mutex_unlock() mutex-debugging fix" * 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: mutex: Always clear owner field upon mutex_unlock() tools/liblockdep: Fix debug_check thinko in mutex destroy
-
Konstantin Khlebnikov authored
Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel BUG at mm/rmap.c:399!") caused by commit 7a3ef208 ("mm: prevent endless growth of anon_vma hierarchy") Anon_vma_clone() is usually called for a copy of source vma in destination argument. If source vma has anon_vma it should be already in dst->anon_vma. NULL in dst->anon_vma is used as a sign that it's called from anon_vma_fork(). In this case anon_vma_clone() finds anon_vma for reusing. Vma_adjust() calls it differently and this breaks anon_vma reusing logic: anon_vma_clone() links vma to old anon_vma and updates degree counters but vma_adjust() overrides vma->anon_vma right after that. As a result final unlink_anon_vmas() decrements degree for wrong anon_vma. This patch assigns ->anon_vma before calling anon_vma_clone(). Signed-off-by:Konstantin Khlebnikov <koct9i@gmail.com> Reported-and-tested-by:
Chris Clayton <chris2553@googlemail.com> Reported-and-tested-by:
Oded Gabbay <oded.gabbay@amd.com> Reported-and-tested-by:
Chih-Wei Huang <cwhuang@android-x86.org> Acked-by:
Rik van Riel <riel@redhat.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Daniel Forrest <dan.forrest@ssec.wisc.edu> Cc: Michal Hocko <mhocko@suse.cz> Cc: stable@vger.kernel.org # to match back-porting of 7a3ef208Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Commit fee7e49d ("mm: propagate error from stack expansion even for guard page") made sure that we return the error properly for stack growth conditions. It also theorized that counting the guard page towards the stack limit might break something, but also said "Let's see if anybody notices". Somebody did notice. Apparently android-x86 sets the stack limit very close to the limit indeed, and including the guard page in the rlimit check causes the android 'zygote' process problems. So this adds the (fairly trivial) code to make the stack rlimit check be against the actual real stack size, rather than the size of the vma that includes the guard page. Reported-and-tested-by:
-
Ingo Molnar authored
Signed-off-by:Ingo Molnar <mingo@kernel.org>
-
- 10 Jan, 2015 2 commits
-
-
git://github.com/awilliam/linux-vfioLinus Torvalds authored
Pull VFIO fix from Alex Williamson: "Fix PCI header check in vfio_pci_probe() (Wei Yang)" * tag 'vfio-v3.19-rc4' of git://github.com/awilliam/linux-vfio: vfio-pci: Fix the check on pci device type in vfio_pci_probe()
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull SCSI fix from James Bottomley: "Just one fix: a qlogic busy wait regression" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: qla2xxx: fix busy wait regression
-
