- 05 Oct, 2014 40 commits
-
-
Thomas Pugliese authored
commit 675f0ab2 upstream. Make sure the uwb_dev->bce entry is set before calling uwb_dev_add in uwbd_dev_onair so that usermode will only see the device after it is properly initialized. This fixes a kernel panic that can occur if usermode tries to access the IEs sysfs attribute of a UWB device before the driver has had a chance to set the beacon cache entry. Signed-off-by:
Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
commit 30966910 upstream. Add back some PIDs that were mistakingly remove when reverting commit 73228a05 ("USB: option,zte_ev: move most ZTE CDMA devices to zte_ev"), which apparently did more than its commit message claimed in that it not only moved some PIDs from option to zte_ev but also added some new ones. Fixes: 63a901c0 ("Revert "USB: option,zte_ev: move most ZTE CDMA devices to zte_ev"") Reported-by:
Lei Liu <lei35151@163.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit ee444609 upstream. Add device id for NOVITUS Bono E thermal printer. Reported-by:
Emanuel Koczwara <poczta@emanuelkoczwara.pl> Signed-off-by:
-
Taylor Braun-Jones authored
commit 9c491c37 upstream. Signed-off-by:
Taylor Braun-Jones <taylor.braun-jones@ge.com> Cc: Johan Hovold <johan@kernel.org> Signed-off-by:
-
Ivan T. Ivanov authored
commit 233c7daf upstream. Initialize USB PHY after every Link controller reset Cc: Tim Bird <tbird20d@gmail.com> Signed-off-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by:
-
Ivan T. Ivanov authored
commit ea290056 upstream. PHY drivers keep track of the current state of the hardware, so don't change PHY settings under it. Cc: Tim Bird <tbird20d@gmail.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Tony Lindgren authored
commit 96be39ab upstream. Commit 30a70b02 ("usb: musb: fix obex in g_nokia.ko causing kernel panic") attempted to fix runtime PM handling for PHYs that are on the I2C bus. Commit 3063a12b ("usb: musb: fix PHY power on/off") then changed things around to enable of PHYs that rely on runtime PM. These changes however broke idling of the PHY and causes at least 100 mW extra power consumption on omaps, which is a lot with the idle power consumption being below 10 mW range on many devices. As calling phy_power_on/off from runtime PM calls in the USB causes complicated issues with I2C connected PHYs, let's just let the PHY do it's own runtime PM as needed. This leaves out the dependency between PHYs and USB controller drivers for runtime PM. Let's fix the regression for twl4030-usb by adding minimal runtime PM support. This allows idling the PHY on disconnect. Note that we are changing to use standard runtime PM handling for twl4030_phy_init() as that function just checks the state and does not initialize the PHY. The PHY won't get initialized until in twl4030_phy_power_on(). Fixes: 30a70b02 ("usb: musb: fix obex in g_nokia.ko causing kernel panic") Fixes: 3063a12b ("usb: musb: fix PHY power on/off") Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Tony Lindgren authored
commit 85601b8d upstream. Commit 249751f2 ("usb: phy: twl4030-usb: poll for ID disconnect") added twl4030_id_workaround_work() to deal with lost interrupts after ID pin goes down. Looks like commit f1ddc24c ("usb: phy: twl4030-usb: remove *set_suspend* and *phy_init* ops") changed things around for the generic phy framework, and delayed work no longer got called except initially during boot. The PHY connect and disconnect interrupts for twl4030-usb are not working after disconnecting a USB-A cable from the board, and the deeper idle states for omap are blocked as the USB controller stays busy. The issue can be solved by calling delayed work from twl4030_usb_irq() when ID pin is down and the PHY is not asleep like we already do in twl4030_id_workaround_work(). But as both twl4030_usb_irq() and twl4030_id_workaround_work() already do pretty much the same thing, let's call twl4030_usb_irq() from twl4030_id_workaround_work() instead of adding some more duplicate code. We also must call sysfs_notify() only when we have an interrupt and not from the delayed work as notified by Grazvydas Ignotas <notasas@gmail.com>. Fixes: f1ddc24c ("usb: phy: twl4030-usb: remove *set_suspend* and *phy_init* ops") Acked-by:
-
Thierry Reding authored
commit 9ce9ec95 upstream. The PHY configuration is stored in an opaque "config" field, but when allocating the structure, its proper size needs to be known. In the case of UTMI, the proper structure is tegra_utmip_config of which a local variable already exists, so we can use that to obtain the size from. Fixes the following warning from the sparse checker: drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void) Fixes: 81d5dfe6 (usb: phy: tegra: Read UTMIP parameters from device tree) Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Bjørn Mork authored
commit 5b3da692 upstream. This VID:PID is used for some Direct IP devices behaving identical to the already supported 0F3D:68AA devices. Reported-by:
Lars Melin <larsm17@gmail.com> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Bjørn Mork authored
commit 049255f5 upstream. Sierra Wireless Direct IP devices using the 68A3 product ID can be configured for modes including a CDC ECM class function. The known example uses interface numbers 12 and 13 for the ECM control and data interfaces respectively, consistent with CDC MBIM function interface numbering on other Sierra devices. It seems cleaner to restrict this driver to the ff/ff/ff vendor specific interfaces rather than increasing the already long interface number blacklist. This should be more future proof if Sierra adds more class functions using interface numbers not yet in the blacklist. Signed-off-by:
-
Johan Hovold authored
commit 754eb21c upstream. Remove dublicate Qualcom PID 0x3197 which is already handled by the moto-modem driver since commit 6986a978 ("USB: add new moto_modem driver for some Morotola phones"). Fixes: 799ee924 ("USB: serial: add zte_ev.c driver") Signed-off-by:
-
Johan Hovold authored
commit 95be5739 upstream. Remove dublicate Gobi PID 0x9008 which is already handled by the qcserial driver since commit f05932c0 ("USB: qcserial: Add extra device IDs"). Fixes: 799ee924 ("USB: serial: add zte_ev.c driver") Signed-off-by:
-
Johan Hovold authored
commit 63a901c0 upstream. This reverts commit 73228a05 ("USB: option,zte_ev: move most ZTE CDMA devices to zte_ev"). Move the IDs of the devices that were previously driven by the option driver back to that driver. As several users have reported, the zte_ev driver is causing random disconnects as well as reconnect failures. A closer analysis of the zte_ev setup code reveals that it consists of standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE) but unfortunately fails to get some of those right. In particular, as reported by Liu Lei, it fails to lower DTR/RTS on close. It also appears that the control requests lack the interface argument. Note that the zte_ev driver is based on code (once) distributed by ZTE that still appears to originally have been reverse-engineered and bolted onto the generic driver. Since line control is already handled properly by the option driver, and the SET/GET_LINE_CODING requests appears to be redundant (amounts to a SET 9600 8N1), this is a first step in ultimately removing the redundant zte_ev driver. Note that AC2726 had already been moved back to option, and that some IDs were in the device table of both drivers prior to the commit being reverted. Reported-by:
Lei Liu <liu.lei78@zte.com.cn> Signed-off-by:
-
Brennan Ashton authored
commit d7730273 upstream. This VIA Telecom baseband processor is used is used by by u-blox in both the FW2770 and FW2760 products and may be used in others as well. This patch has been tested on both of these modem versions. Signed-off-by:
Brennan Ashton <bashton@brennanashton.com> Signed-off-by:
-
Johan Hovold authored
commit f0e4cba2 upstream. Do not log normal interrupt-urb shutdowns as errors. The option driver has always been logging any nonzero interrupt-urb status as an error, including when the urb is killed during normal operation. Commit 9096f1fb ("USB: usb_wwan: fix potential NULL-deref at resume") moved the interrupt urb submission from port probe and release to open and close, thus potentially increasing the number of these false-positive error messages dramatically. Reported-by:
Ed Butler <ressy66@ausics.net> Tested-by:
-
Johan Hovold authored
commit 5654699f upstream. Make sure to verify the number of ports requested by subdriver to avoid writing beyond the end of fixed-size array in interface data. The current usb-serial implementation is limited to eight ports per interface but failed to verify that the number of ports requested by a subdriver (which could have been determined from device descriptors) did not exceed this limit. Signed-off-by:
-
Stephen Hemminger authored
commit 5b6b80ae upstream. I have a j5 create (JUA210) USB 2 video device and adding it device id to SIS USB video gets it to work. Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
Johan Hovold authored
commit d979e9f9 upstream. Make sure to verify the maximum number of endpoints per type to avoid writing beyond the end of a stack-allocated array. The current usb-serial implementation is limited to eight ports per interface but failed to verify that the number of endpoints of a certain type reported by a device did not exceed this limit. Signed-off-by:
-
Greg KH authored
commit 91fcb1ce upstream. This adds a new device id to the pl2303 driver for the ZTEK device. Reported-by:
Mike Chu <Mike-Chu@prolific.com.tw> Signed-off-by:
-
Andrzej Pietrasiewicz authored
commit 45465273 upstream. f->os_desc_table[0].if_id is zero by default. If the actual id happens to be different then no Feature Descriptors will be returned to the host for this interface, so assign if_id as soon as it is known. Acked-by:
Michal Nazarewicz <mina86@mina86.com> Signed-off-by:
Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by:
-
Alexey Khoroshilov authored
commit 9ef7db7f upstream. Commit 0244756e ("ufs: sb mutex merge + mutex_destroy") introduces deadlocks in ufs_new_inode() and ufs_free_inode(). Most callers of that functions acqure the mutex by themselves and ufs_{new,free}_inode() do that via lock_ufs(), i.e we have an unavoidable double lock. The patch proposes to resolve the issue by making sure that ufs_{new,free}_inode() are not called with the mutex held. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Jeff Layton authored
commit e0b760ff upstream. The argument to locks_unlink_lock can't be just any pointer to a pointer. It must be a pointer to the fl_next field in the previous lock in the list. Signed-off-by:
Jeff Layton <jlayton@primarydata.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Max Filippov authored
commit d1b6ba82 upstream. Remove restoring a6 on some return paths and instead modify and restore it in a single place, using symbolic name. Correctly restore a7 from PT_AREG7 in case of illegal a6 value. Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Max Filippov authored
commit 7128039f upstream. Current definition of TLBTEMP_BASE_2 is always 32K above the TLBTEMP_BASE_1, whereas fast_second_level_miss handler for the TLBTEMP region analyzes virtual address bit (PAGE_SHIFT + DCACHE_ALIAS_ORDER) to determine TLBTEMP region where the fault happened. The size of the TLBTEMP region is also checked incorrectly: not 64K, but twice data cache way size (whicht may as well be less than the instruction cache way size). Fix TLBTEMP_BASE_2 to be TLBTEMP_BASE_1 + data cache way size. Provide TLBTEMP_SIZE that is a greater of doubled data cache way size or the instruction cache way size, and use it to determine if the second level TLB miss occured in the TLBTEMP region. Practical occurence of page faults in the TLBTEMP area is extremely rare, this code can be tested by deletion of all w[di]tlb instructions in the tlbtemp_mapping region. Signed-off-by:
-
Max Filippov authored
commit 52247123 upstream. With SMP and a lot of debug options enabled task_struct::thread gets out of reach of s32i/l32i instructions with base pointing at task_struct, breaking build with the following messages: arch/xtensa/kernel/entry.S: Assembler messages: arch/xtensa/kernel/entry.S:1002: Error: operand 3 of 'l32i.n' has invalid value '1048' arch/xtensa/kernel/entry.S:1831: Error: operand 3 of 's32i.n' has invalid value '1040' arch/xtensa/kernel/entry.S:1832: Error: operand 3 of 's32i.n' has invalid value '1044' Change base to point to task_struct::thread in such cases. Don't use a10 in _switch_to to save/restore prev pointer as a2 is not clobbered. Signed-off-by:
-
Alan Douglas authored
commit 1ca49463 upstream. Virtual address is translated to the XCHAL_KSEG_CACHED region in the dma_free_coherent, but is checked to be in the 0...XCHAL_KSEG_SIZE range. Change check for end of the range from 'addr >= X' to 'addr > X - 1' to handle the case of X == 0. Replace 'if (C) BUG();' construct with 'BUG_ON(C);'. Signed-off-by:
Alan Douglas <adouglas@cadence.com> Signed-off-by:
-
Max Filippov authored
commit f61bf8e7 upstream. This fixes userspace code that builds on other architectures but fails on xtensa due to references to structures that other architectures don't refer to. E.g. this fixes the following issue with python-2.7.8: python-2.7.8/Modules/termios.c:861:25: error: invalid application of 'sizeof' to incomplete type 'struct serial_multiport_struct' {"TIOCSERGETMULTI", TIOCSERGETMULTI}, python-2.7.8/Modules/termios.c:870:25: error: invalid application of 'sizeof' to incomplete type 'struct serial_multiport_struct' {"TIOCSERSETMULTI", TIOCSERSETMULTI}, python-2.7.8/Modules/termios.c:900:24: error: invalid application of 'sizeof' to incomplete type 'struct tty_struct' {"TIOCTTYGSTRUCT", TIOCTTYGSTRUCT}, Signed-off-by:
-
Alex Deucher authored
commit 370ce45b upstream. Otherwise we may fail to init the second compute ring. Noticed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 39da0384 upstream. Need to properly disable nb dpm on dpm disable. Signed-off-by:
-
Alex Deucher authored
commit c1789a2e upstream. Otherwise we may lose the DMA golden settings which can lead to hangs, etc. Reviewed-by:
-
Alex Deucher authored
commit 799028d5 upstream. Otherwise we may lose the DMA golden settings which can lead to hangs, etc. Reviewed-by:
-
Alex Deucher authored
commit 31a25e2c upstream. Otherwise we may lose the DMA golden settings which can lead to hangs, etc. bug: https://www.libreoffice.org/bugzilla/show_bug.cgi?id=83500Reviewed-by:
-
Alex Deucher authored
commit 1952f24d upstream. Vbios connector table lists non-existent VGA port. Bug: https://bugs.freedesktop.org/show_bug.cgi?id=83184Signed-off-by:
-
Alex Deucher authored
commit ff437792 upstream. On systems with special thermal configurations make sure we make note of the thermal setup. This is required for proper firmware configuration on these systems. Signed-off-by:
-
Christian König authored
commit f229407d upstream. Semaphore values have 64 bits, not 32. This fixes a very subtle bug that disables synchronization when the upper 32bits wasn't zero. Signed-off-by:
Grigori Goronzy <greg@chown.ath.cx> Signed-off-by:
-
Alex Deucher authored
commit 0a5f6e9d upstream. This is a port of cedb655a to older asics. Fixes a possible divide by 0 if the harvest register is invalid. v2: drop some additional harvest munging. Signed-off-by:
-
Alex Deucher authored
commit 52da51f0 upstream. Need to initialize the mask to 0 on init, otherwise it keeps increasing. bug: https://bugzilla.kernel.org/show_bug.cgi?id=82581 v2: also fix cu count v3: split count fix into separate patch Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 6101b3ae upstream. This fixes the CU count reported to userspace for OpenCL. bug: https://bugzilla.kernel.org/show_bug.cgi?id=82581Signed-off-by:
-
Alex Deucher authored
commit c940b447 upstream. pm_suspend is handled in the radeon_suspend callbacks. pm_resume has special handling depending on whether dpm or legacy pm is enabled. Change radeon_gpu_reset to mirror the behavior in the suspend and resume pathes. Signed-off-by:
-
