sdhci-pci-o2micro.c contains no initialisation and its functions are only
called from shdci-pci.c, so there is no reason for it to be a separate
module, let alone or for it to always be built-in.

- Rename sdhci-pci.c to sdhci-pci-core.c so that the sdhci-pci module
  can be built from multiple source files
- Add sdhci-pci-o2micro.c to it
- Remove redundant exports
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

According to hardware spec, validate DDR50 mode
for SDXC.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

CMD19 tuning is also available for DDR50 mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As SD Specifications Part1 Physical Layer Specification Version
3.01 says, CMD19 tuning is available for unlocked cards in transfer
state of 1.8V signaling mode. The small difference between v3.00
and 3.01 spec means that CMD19 tuning is also available for DDR50
mode.
Signed-off-by: Weijun Yang <york.yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MMC_IOC_CMD and MMC_IOC_MULTI_CMD ioctl() code currently bails on
any eMMC errors. However, in case there is any resp[] data, we
should attempt to copy resp[] back to user space. The user app
can then determine which command(s) failed in the MMC_IOC_MULTI_CMD
case AND/OR report better diagnostics in both cases.

Gwendal Grignou provided the idea and it was previously implemented
and tested on v3.18 ChromeOS kernel:
    https://chromium-review.googlesource.com/#/c/299956Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Hyung Taek Ryoo <hryoo@nvidia.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: David Riley <davidriley@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch add MMC_TIMING_UHS_SDR12 and MMC_TIMING_UHS_SDR25
for mmc_ios_show to show the ios->timing if mmc card runs under
these two modes.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some sdio wifi modules have not been working reliable with the sunxi-mmc
host code. This turns out to be caused by starting new io-rw commands while
the card signals that it is still busy processing a previous command.

This commit adds card-busy detection to the sunxi-mmc driver which together
with recent core changes to check card-busy before starting io-rw commands
fixes the wifi reliability issues on the Cubietruck and other sunxi boards
using sdio wifi.
Reported-by: Eugene K <sigintmailru@gmail.com>
Suggested-by: Eugene K <sigintmailru@gmail.com>
Cc: Eugene K <sigintmailru@gmail.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some sdio wifi chips will not work properly if we try to start new
sdio-rw requests while the device is signalling that it is busy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a helper function to check if an opcode is a sd-io-rw-* opcode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Certain eMMC devices allow vendor specific device information to be read
via a sequence of vendor commands. These vendor commands must be issued
in sequence and an atomic fashion. One way to support this would be to
add an ioctl function for sending a sequence of commands to the device
atomically as proposed here. These multi commands are simple array of
the existing mmc_ioc_cmd structure.

The structure passed via the ioctl uses a __u64 type to specify the number
of commands (so that the structure is aligned on a 64-bit boundary) and a
zero length array as a header for list of commands to be issued. The
maximum number of commands that can be sent is determined by
MMC_IOC_MAX_CMDS (which defaults to 255 and should be more than
sufficient).

This based upon work by Seshagiri Holi <sholi@nvidia.com>.
Signed-off-by: Seshagiri Holi <sholi@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Enable interrupt mode to detect card instead of polling mode for
ls1021a by removing the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION.
This could improve data transferring performance and avoid the call
trace caused by polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The simple power sequence provider sets a value for multiple GPIOs in one
go so it is better to use the API already provided by the GPIO descriptor
API instead of open coding the same logic.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add MMC_CAP_RUNTIME_RESUME support to save resume time
Drop unnecessary SDC_ARG write
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch add ios->drv_type for mmc_ios_show to show the
card's driver type.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The goto is correct and the unreachable "return -EINVAL" should be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

sdhci_init() will clear all irqs and set the needed irqs. So
logically sdhci_init() should be called before request irq.

If not, some irqs may be triggled and handled wrongly. Take
the following into consideration, after request irq, if
SDIO card interrupt enabled, a sd card in the sd slot will
trigger a mass of interrupt(SDHCI_INT_CARD_INT), because at
this time, the vmmc-regulator still not restore, no voltage
supply for the sd card, so the pin of data0~data3 change and
keep low, interrupt(SDHCI_INT_CARD_INT) will rise up ceaselessly.
Due to we already reguest irq, system will be busy in handling
this endless irq, can't response to other event.

So we should call sdhci_init() before request irq in sd resume.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The driver prints if the data width is 8-bit but it's using a
binary OR instead of a binary AND so it will always report as
"is_8bit=Y" regardless of the flags in host->mmc->caps.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The gpiod_get() function expands to gpiod_get_index() with index 0
so it's better to use it since is easier to read and more concise.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As there are no users of the __mmc_switch() API, except for the mmc core
itself, let's convert it from an exported function into an internal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

They aren't needed and are just creating null statements so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It's not needed an is just creating a null statement, so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.

In some code paths for SDIO, particularly related to the PM support,
mmc_power_off|up() is invoked without keeping the host claimed. Let's fix
these.

Moreover, mmc_start|stop_host() also invokes mmc_power_off|up() without
claiming the host, let's fix these as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>

Add an entry to the sdhci_acpi_uids list to detect the SD card
reader on the Asus X205Ta laptop.

dstd table:

Device (SDHC)
{
    Name (_ADR, Zero)  // _ADR: Address
    Name (_HID, "PNP0FFF")  // _HID: Hardware ID
    Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
    Name (_DDN, "Intel(R) SD Card Controller - 80860F16")  // _DDN: DOS Dev
    Name (_UID, 0x03)  // _UID: Unique ID
    Name (RDEP, Package (0x02)
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull USB fixes from Greg KH:
 "Here are three xhci driver fixes for reported issues for 4.3-rc7

  All have been in linux-next for a while with no problems"

* tag 'usb-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: Add spurious wakeup quirk for LynxPoint-LP controllers
  xhci: handle no ping response error properly
  xhci: don't finish a TD if we get a short transfer event mid TD

Pull tty/serial fixes from Greg KH:
 "Here are two fixes that resolve reported issues, one with the 8250
  driver, and the other with the generic fbcon driver.

  Both have been in linux-next for a while"

* tag 'tty-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  fbcon: initialize blink interval before calling fb_set_par
  Revert "serial: 8250_dma: don't bother DMA with small transfers"

Pull staging driver fixes from Greg KH:
 "Here are four iio driver fixes for 4.3-rc7, fixing some reported
  issues.  All of these have been in linux-next for a while"

* tag 'staging-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: mxs-lradc: Fix temperature offset
  iio: accel: sca3000: memory corruption in sca3000_read_first_n_hw_rb()
  iio: st_accel: fix interrupt handling on LIS3LV02
  iio: adc: twl4030: Fix ADC[3:6] readings

Pull infiniband fixes from Doug Ledford:
 "It's late in the game, I know, but these fixes seemed important enough
  to warrant a late pull request.  They all involve oopses or use after
  frees or corruptions.

  Six serious fixes:

   - Hold the mutex around the find and corresponding update of our gid

   - The ifa list is rcu protected, copy its contents under rcu to avoid
     using a freed structure

   - On error, netdev might be null, so check it before trying to
     release it

   - On init, if workqueue alloc fails, fail init

   - The new demux patches exposed a bug in mlx5 and ipath drivers, we
     need to use the payload P_Key to determine the P_Key the packet
     arrived on because the hardware doesn't tell us the truth

   - Due to a couple convoluted error flows, it is possible for the CM
     to trigger a use_after_free and a double_free of rb nodes.  Add two
     checks to prevent that.  This code has worked for 10+ years.  It is
     likely that some of the recent changes have caused this issue to
     surface.  The current patch will protect us from nasty events for
     now while we track down why this is just now showing up"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/cm: Fix rb-tree duplicate free and use-after-free
  IB/cma: Use inner P_Key to determine netdev
  IB/ucma: check workqueue allocation before usage
  IB/cma: Potential NULL dereference in cma_id_from_event
  IB/core: Fix use after free of ifa
  IB/core: Fix memory corruption in ib_cache_gid_set_default_gid

Pull device mapper fixes from Mike Snitzer:
 "Three stable fixes (two in btree code used by DM thinp and one to
  properly store flags in DM cache metadata's superblock)"

* tag 'dm-4.3-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm cache: the CLEAN_SHUTDOWN flag was not being set
  dm btree: fix leak of bufio-backed block in btree_split_beneath error path
  dm btree remove: fix a bug when rebalancing nodes after removal

Pull block layer fixes from Jens Axboe:
 "A final set of fixes for 4.3.

  It is (again) bigger than I would have liked, but it's all been
  through the testing mill and has been carefully reviewed by multiple
  parties.  Each fix is either a regression fix for this cycle, or is
  marked stable.  You can scold me at KS.  The pull request contains:

   - Three simple fixes for NVMe, fixing regressions since 4.3.  From
     Arnd, Christoph, and Keith.

   - A single xen-blkfront fix from Cathy, fixing a NULL dereference if
     an error is returned through the staste change callback.

   - Fixup for some bad/sloppy code in nbd that got introduced earlier
     in this cycle.  From Markus Pargmann.

   - A blk-mq tagset use-after-free fix from Junichi.

   - A backing device lifetime fix from Tejun, fixing a crash.

   - And finally, a set of regression/stable fixes for cgroup writeback
     from Tejun"

* 'for-linus' of git://git.kernel.dk/linux-block:
  writeback: remove broken rbtree_postorder_for_each_entry_safe() usage in cgwb_bdi_destroy()
  NVMe: Fix memory leak on retried commands
  block: don't release bdi while request_queue has live references
  nvme: use an integer value to Linux errno values
  blk-mq: fix use-after-free in blk_mq_free_tag_set()
  nvme: fix 32-bit build warning
  writeback: fix incorrect calculation of available memory for memcg domains
  writeback: memcg dirty_throttle_control should be initialized with wb->memcg_completions
  writeback: bdi_writeback iteration must not skip dying ones
  writeback: fix bdi_writeback iteration in wakeup_dirtytime_writeback()
  writeback: laptop_mode_timer_fn() needs rcu_read_lock() around bdi_writeback iteration
  nbd: Add locking for tasks
  xen-blkfront: check for null drvdata in blkback_changed (XenbusStateClosing)

Pull Ceph fixes from Sage Weil:
 "Two fixes.

  One is a stopgap to prevent a stack blowout when users have a deep
  chain of image clones.  (We'll rewrite this code to be non-recursive
  for the next window, but in the meantime this is a simple fix that
  avoids a crash.)

  The second fixes a refcount underflow"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: prevent kernel stack blow up on rbd map
  rbd: don't leak parent_spec in rbd_dev_probe_parent()

Pull btrfs fixes from Chris Mason:
 "I have two more small fixes this week:

  Qu's fix avoids unneeded COW during fallocate, and Christian found a
  memory leak in the error handling of an earlier fix"

* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix possible leak in btrfs_ioctl_balance()
  btrfs: Avoid truncate tailing page if fallocate range doesn't exceed inode size

If the CLEAN_SHUTDOWN flag is not set when a cache is loaded then all cache
blocks are marked as dirty and a full writeback occurs.

__commit_transaction() is responsible for setting/clearing
CLEAN_SHUTDOWN (based the flags_mutator that is passed in).

Fix this issue, of the cache's on-disk flags being wrong, by making sure
__commit_transaction() does not reset the flags after the mutator has
altered the flags in preparation for them being serialized to disk.

before:

sb_flags = mutator(le32_to_cpu(disk_super->flags));
disk_super->flags = cpu_to_le32(sb_flags);
disk_super->flags = cpu_to_le32(cmd->flags);

after:

disk_super->flags = cpu_to_le32(cmd->flags);
sb_flags = mutator(le32_to_cpu(disk_super->flags));
disk_super->flags = cpu_to_le32(sb_flags);
Reported-by: Bogdan Vasiliev <bogdan.vasiliev@gmail.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.

Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
Cc: stable@vger.kernel.org

Commit 4c7e3093 ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().

The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them.  If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.

Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.

Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.cSigned-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org