- 17 May, 2022 9 commits
-
-
Leszek Polak authored
As per Errata Section 5.1, if EEE is intended to be used, some register writes must be done once after every hardware reset. This patch now adds the necessary register writes as listed in the Marvell errata. Without this fix we experience ethernet problems on some of our boards equipped with a new version of this ethernet PHY (different supplier). The fix applies to Marvell Alaska 88E1510/88E1518/88E1512/88E1514 Rev. A0. Signed-off-by:
Leszek Polak <lpolak@arri.de> Signed-off-by:
Stefan Roese <sr@denx.de> Cc: Marek Behún <kabel@kernel.org> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Cc: David S. Miller <davem@davemloft.net> Reviewed-by:
Marek Behún <kabel@kernel.org> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220516070859.549170-1-sr@denx.deSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Minghao Chi authored
Calling synchronize_irq() right before free_irq() is quite useless. On one hand the IRQ can easily fire again before free_irq() is entered, on the other hand free_irq() itself calls synchronize_irq() internally (in a race condition free way), before any state associated with the IRQ is freed. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Link: https://lore.kernel.org/r/20220516082251.1651350-1-chi.minghao@zte.com.cnSigned-off-by:
-
Minghao Chi authored
Calling synchronize_irq() right before free_irq() is quite useless. On one hand the IRQ can easily fire again before free_irq() is entered, on the other hand free_irq() itself calls synchronize_irq() internally (in a race condition free way), before any state associated with the IRQ is freed. Reported-by:
-
Minghao Chi authored
Calling synchronize_irq() right before free_irq() is quite useless. On one hand the IRQ can easily fire again before free_irq() is entered, on the other hand free_irq() itself calls synchronize_irq() internally (in a race condition free way), before any state associated with the IRQ is freed. Reported-by:
-
Lu Wei authored
Merge repeat codes to reduce the duplication. Signed-off-by:
Lu Wei <luwei32@huawei.com> Link: https://lore.kernel.org/r/20220516062804.254742-1-luwei32@huawei.comSigned-off-by:
-
Lu Wei authored
Use eth_zero_addr() to clear mac address instead of memset(). Signed-off-by:
-
Bernard Zhao authored
devm_kfree check the pointer, there is no need to check before devm_kfree call. This change is to cleanup the code a bit. Signed-off-by:
Bernard Zhao <bernard@vivo.com> Link: https://lore.kernel.org/r/20220516015208.6526-1-bernard@vivo.comSigned-off-by:
-
Wells Lu authored
Removed unnecessary: select COMMON_CLK_SP7021 select RESET_SUNPLUS select NVMEM_SUNPLUS_OCOTP from Kconfig. Reported-by:
kernel test robot <yujie.liu@intel.com> Signed-off-by:
Wells Lu <wellslutw@gmail.com> Link: https://lore.kernel.org/r/1652443036-24731-1-git-send-email-wellslutw@gmail.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Merge tag 'linux-can-next-for-5.19-20220516' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2022-05-16 the first 2 patches are by me and target the CAN raw protocol. The 1st removes an unneeded assignment, the other one adds support for SO_TXTIME/SCM_TXTIME. Oliver Hartkopp contributes 2 patches for the ISOTP protocol. The 1st adds support for transmission without flow control, the other let's bind() return an error on incorrect CAN ID formatting. Geert Uytterhoeven contributes a patch to clean up ctucanfd's Kconfig file. Vincent Mailhol's patch for the slcan driver uses the proper function to check for invalid CAN frames in the xmit callback. The next patch is by Geert Uytterhoeven and makes the interrupt-names of the renesas,rcar-canfd dt bindings mandatory. A patch by my update the ctucanfd dt bindings to include the common CAN controller bindings. The last patch is by Akira Yokosawa and fixes a breakage the ctucanfd's documentation. * tag 'linux-can-next-for-5.19-20220516' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: docs: ctucanfd: Use 'kernel-figure' directive instead of 'figure' dt-bindings: can: ctucanfd: include common CAN controller bindings dt-bindings: can: renesas,rcar-canfd: Make interrupt-names required can: slcan: slc_xmit(): use can_dropped_invalid_skb() instead of manual check can: ctucanfd: Let users select instead of depend on CAN_CTUCANFD can: isotp: isotp_bind(): return -EINVAL on incorrect CAN ID formatting can: isotp: add support for transmission without flow control can: raw: add support for SO_TXTIME/SCM_TXTIME can: raw: raw_sendmsg(): remove not needed setting of skb->sk ==================== Link: https://lore.kernel.org/r/20220516202625.1129281-1-mkl@pengutronix.deSigned-off-by:
-
- 16 May, 2022 31 commits
-
-
Jakub Kicinski authored
Ricardo Martinez says: ==================== net: skb: Remove skb_data_area_size() This patch series removes the skb_data_area_size() helper, replacing it in t7xx driver with the size used during skb allocation. https://lore.kernel.org/netdev/CAHNKnsTmH-rGgWi3jtyC=ktM1DW2W1VJkYoTMJV2Z_Bt498bsg@mail.gmail.com/ ==================== Link: https://lore.kernel.org/r/20220513173400.3848271-1-ricardo.martinez@linux.intel.comSigned-off-by:
-
Ricardo Martinez authored
skb_data_area_size() is not needed. As Jakub pointed out [1]: For Rx, drivers can use the size passed during skb allocation or use skb_tailroom(). For Tx, drivers should use skb_headlen(). [1] https://lore.kernel.org/netdev/CAHNKnsTmH-rGgWi3jtyC=ktM1DW2W1VJkYoTMJV2Z_Bt498bsg@mail.gmail.com/Signed-off-by:
Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by:
-
Ricardo Martinez authored
skb_data_area_size() helper was used to calculate the size of the DMA mapped buffer passed to the HW. Instead of doing this, use the size passed to allocate the skbs. Signed-off-by:
-
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: Updates for net-next Three independent fixes/features from the MPTCP tree: Patch 1 is a selftest workaround for older iproute2 packages. Patch 2 removes superfluous locks that were added with recent MP_FAIL patches. Patch 3 adds support for the TCP_DEFER_ACCEPT sockopt. ==================== Link: https://lore.kernel.org/r/20220514002115.725976-1-mathew.j.martineau@linux.intel.comSigned-off-by:
-
Florian Westphal authored
Support this via passthrough to the underlying tcp listener socket. Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/271Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Paolo Abeni authored
This reverts commit 4293248c. Additional locks are not needed, all the touched sections are already under mptcp socket lock protection. Fixes: 4293248c ("mptcp: add data lock for sk timers") Signed-off-by:
-
Geliang Tang authored
Old tc versions (iproute2 5.3) show actions in multiple lines, not a single line. Then the following unexpected MP_FAIL selftest output occurs: file received by server has inverted byte at 169 ./mptcp_join.sh: line 1277: [: [{"total acts":1},{"actions":[{"order":0 pedit ,"control_action":{"type":"pipe"}keys 1 index 1 ref 1 bind 1,"installed":0,"last_used":0 key #0 at 148: val ff000000 mask ffffffff 5: integer expression expected 001 Infinite map syn[ ok ] - synack[ ok ] - ack[ ok ] sum[ ok ] - csum [ ok ] ftx[ ok ] - failrx[ ok ] rtx[ ok ] - rstrx [ ok ] itx[ ok ] - infirx[ ok ] ftx[ ok ] - failrx[ ok ] invert This patch adds a 'grep' before 'sed' to fix this. Fixes: b6e074e1 ("selftests: mptcp: add infinite map testcase") Reviewed-by:Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
Geliang Tang <geliang.tang@suse.com> Signed-off-by:
-
Akira Yokosawa authored
Two issues were observed in the ReST doc added by commit c3a0adde ("docs: ctucanfd: CTU CAN FD open-source IP core documentation.") with Sphinx versions 2.4.4 and 4.5.0. The plain "figure" directive broke "make pdfdocs" due to a missing PDF figure. For conversion of SVG -> PDF to work, the "kernel-figure" directive, which is an extension for kernel documentation, should be used instead. The directive of "code:: raw" causes a warning from both "make htmldocs" and "make pdfdocs", which reads: [...]/can/ctu/ctucanfd-driver.rst:75: WARNING: Pygments lexer name 'raw' is not known A plain literal-block marker should suffice where no syntax highlighting is intended. Fix the issues by using suitable directive and marker. Fixes: c3a0adde ("docs: ctucanfd: CTU CAN FD open-source IP core documentation.") Link: https://lore.kernel.org/all/5986752a-1c2a-5d64-f91d-58b1e6decd17@gmail.comSigned-off-by:
Akira Yokosawa <akiyks@gmail.com> Acked-by:
Pavel Pisa <pisa@cmp.felk.cvut.cz> Cc: Martin Jerabek <martin.jerabek01@gmail.com> Cc: Ondrej Ille <ondrej.ille@gmail.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Marc Kleine-Budde authored
Since commit | 1f923440 ("dt-bindings: can: add can-controller.yaml") there is a common CAN controller binding. Add this to the ctucanfd binding. Cc: Ondrej Ille <ondrej.ille@gmail.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Alvin Šipraga authored
Lock the regmap during the whole PHY register access routines in rtl8366rb. Signed-off-by:
Alvin Šipraga <alsi@bang-olufsen.dk> Tested-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20220513213618.2742895-1-linus.walleij@linaro.orgSigned-off-by:
-
Geert Uytterhoeven authored
The Renesas R-Car CAN FD Controller always uses two or more interrupts. Make the interrupt-names properties a required property, to make it easier to identify the individual interrupts. Update the example accordingly. Link: https://lore.kernel.org/all/a68e65955e0df4db60233d468f348203c2e7b940.1651512451.git.geert+renesas@glider.beSigned-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Vincent Mailhol authored
slcan does a manual check in slc_xmit() to verify if the skb is valid. This check is incomplete, use instead can_dropped_invalid_skb(). Link: https://lore.kernel.org/all/20220514141650.1109542-2-mailhol.vincent@wanadoo.frSigned-off-by:
Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by:
-
Geert Uytterhoeven authored
The CTU CAN-FD IP core is only useful when used with one of the corresponding PCI/PCIe or platform (FPGA, SoC) drivers, which depend on PCI resp. OF. Hence make the users select the core driver code, instead of letting then depend on it. Keep the core code config option visible when compile-testing, to maintain compile-coverage. Link: https://lore.kernel.org/all/887b7440446b6244a20a503cc6e8dc9258846706.1652104941.git.geert+renesas@glider.beSigned-off-by:
-
Oliver Hartkopp authored
Commit 3ea56642 ("can: isotp: sanitize CAN ID checks in isotp_bind()") checks the given CAN ID address information by sanitizing the input values. This check (silently) removes obsolete bits by masking the given CAN IDs. Derek Will suggested to give a feedback to the application programmer when the 'sanitizing' was actually needed which means the programmer provided CAN ID content in a wrong format (e.g. SFF CAN IDs with a CAN ID > 0x7FF). Link: https://lore.kernel.org/all/20220515181633.76671-1-socketcan@hartkopp.netSuggested-by:
Derek Will <derekrobertwill@gmail.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
-
Oliver Hartkopp authored
Usually the ISO 15765-2 protocol is a point-to-point protocol to transfer segmented PDUs to a dedicated receiver. This receiver sends a flow control message to specify protocol options and timings (e.g. block size / STmin). The so called functional addressing communication allows a 1:N communication but is limited to a single frame length. This new CAN_ISOTP_CF_BROADCAST allows an unconfirmed 1:N communication with PDU length that would not fit into a single frame. This feature is not covered by the ISO 15765-2 standard. Link: https://lore.kernel.org/all/20220507115558.19065-1-socketcan@hartkopp.netSigned-off-by:
-
Marc Kleine-Budde authored
This patch calls into sock_cmsg_send() to parse the user supplied control information into a struct sockcm_cookie. Then assign the requested transmit time to the skb. This makes it possible to use the Earliest TXTIME First (ETF) packet scheduler with the CAN_RAW protocol. The user can send a CAN_RAW frame with a TXTIME and the kernel (with the ETF scheduler) will take care of sending it to the network interface. Link: https://lore.kernel.org/all/20220502091946.1916211-3-mkl@pengutronix.deAcked-by:
-
Marc Kleine-Budde authored
The skb in raw_sendmsg() is allocated with sock_alloc_send_skb(), which subsequently calls sock_alloc_send_pskb() -> skb_set_owner_w(), which assigns "skb->sk = sk". This patch removes the not needed setting of skb->sk. Link: https://lore.kernel.org/all/20220502091946.1916211-2-mkl@pengutronix.deAcked-by:
-
Fabio Estevam authored
Now that it is possible to use .probe without having .driver_data, let KSZ8061 use the kszphy specific hooks for probe,suspend and resume, which is preferred. Switch to using the dedicated kszphy probe/suspend/resume functions. Signed-off-by:
Fabio Estevam <festevam@denx.de> Reviewed-by:
-
Fabio Estevam authored
Currently, if the .probe element is present in the phy_driver structure and the .driver_data is not, a NULL pointer dereference happens. Allow passing .probe without .driver_data by inserting NULL checks for priv->type. Signed-off-by:
-
Minghao Chi authored
Calling synchronize_irq() right before free_irq() is quite useless. On one hand the IRQ can easily fire again before free_irq() is entered, on the other hand free_irq() itself calls synchronize_irq() internally (in a race condition free way), before any state associated with the IRQ is freed. Reported-by:
David S. Miller <davem@davemloft.net>
-
YueHaibing authored
t7xx_dl_add_timedout() now return int 'ret', but the return type is bool. Change the return type to int for furthor errcode upstream. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Ziyang Xuan authored
vfree(NULL) is safe. NULL check before vfree() is not needed. Delete them to simplify the code. Signed-off-by:
Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by:
-
Zheng Bin authored
octep_init_module misses destroy_workqueue in error path, this patch fixes that. Fixes: 862cd659 ("octeon_ep: Add driver framework and device initialization") Signed-off-by:
Zheng Bin <zhengbin13@huawei.com> Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== net: polish skb defer freeing While testing this recently added feature on a variety of platforms/configurations, I found the following issues: 1) A race leading to concurrent calls to smp_call_function_single_async() 2) Missed opportunity to use napi_consume_skb() 3) Need to limit the max length of the per-cpu lists. 4) Process the per-cpu list more frequently, for the (unusual) case where net_rx_action() has mutiple napi_poll() to process per round. ==================== Signed-off-by: -
Eric Dumazet authored
skb_defer_free_flush() can consume cpu cycles, it seems better to call it in the inner loop: - Potentially frees page/skb that will be reallocated while hot. - Account for the cpu cycles in the @time_limit determination. - Keep softnet_data.defer_count small to reduce chances for skb_attempt_defer_free() to send an IPI. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
commit 68822bdf ("net: generalize skb freeing deferral to per-cpu lists") added another per-cpu cache of skbs. It was expected to be small, and an IPI was forced whenever the list reached 128 skbs. We might need to be able to control more precisely queue capacity and added latency. An IPI is generated whenever queue reaches half capacity. Default value of the new limit is 64. Signed-off-by:
-
Eric Dumazet authored
skb_defer_free_flush() runs from softirq context, we have the opportunity to refill the napi_alloc_cache, and/or use kmem_cache_free_bulk() when this cache is full. Signed-off-by:
-
Eric Dumazet authored
A cpu can observe sd->defer_count reaching 128, and call smp_call_function_single_async() Problem is that the remote CPU can clear sd->defer_count before the IPI is run/acknowledged. Other cpus can queue more packets and also decide to call smp_call_function_single_async() while the pending IPI was not yet delivered. This is a common issue with smp_call_function_single_async(). Callers must ensure correct synchronization and serialization. I triggered this issue while experimenting smaller threshold. Performing the call to smp_call_function_single_async() under sd->defer_lock protection did not solve the problem. Commit 5a18ceca ("smp: Allow smp_call_function_single_async() to insert locked csd") replaced an informative WARN_ON_ONCE() with a return of -EBUSY, which is often ignored. Test of CSD_FLAG_LOCK presence is racy anyway. Fixes: 68822bdf ("net: generalize skb freeing deferral to per-cpu lists") Signed-off-by:
-
Rolf Eike Beer authored
Works fine on my HP C3600: [ 274.452394] tulip0: no phy info, aborting mtable build [ 274.499041] tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1 [ 274.750691] net eth0: Digital DS21142/43 Tulip rev 65 at MMIO 0xf4008000, 00:30:6e:08:7d:21, IRQ 17 [ 283.104520] net eth0: Setting full-duplex based on MII#1 link partner capability of c1e1 Signed-off-by:
Rolf Eike Beer <eike-kernel@sf-tec.de> Signed-off-by:
-
Zheng Bin authored
hinic_pf_to_mgmt_init misses destroy_workqueue in error path, this patch fixes that. Fixes: 6dbb8901 ("hinic: fix sending mailbox timeout in aeq event work") Signed-off-by:
-
David S. Miller authored
Menglong Dong says: ==================== net: skb: check the boundrary of skb drop reason In the commit 1330b6ef ("skb: make drop reason booleanable"), SKB_NOT_DROPPED_YET is added to the enum skb_drop_reason, which makes the invalid drop reason SKB_NOT_DROPPED_YET can leak to the kfree_skb tracepoint. Once this happen (it happened, as 4th patch says), it can cause NULL pointer in drop monitor and result in kernel panic. Therefore, check the boundrary of drop reason in both kfree_skb_reason (2th patch) and drop monitor (1th patch) to prevent such case happens again. Meanwhile, fix the invalid drop reason passed to kfree_skb_reason() in tcp_v4_rcv() and tcp_v6_rcv(). Changes since v2: 1/4 - don't reset the reason and print the debug warning only (Jakub Kicinski) 4/4 - remove new lines between tags Changes since v1: - consider tcp_v6_rcv() in the 4th patch ==================== Signed-off-by:
-
