- 09 Jan, 2019 14 commits
-
-
Cong Wang authored
[ Upstream commit d5c7c745 ] When x25_asy_open() fails, it already cleans up by itself, so its caller doesn't need to free the memory again. It seems we still have to call x25_asy_free() to clear the SLF_INUSE bit, so just set these pointers to NULL after kfree(). Reported-and-tested-by: syzbot+5e5e969e525129229052@syzkaller.appspotmail.com Fixes: 3b780bed ("x25_asy: Free x25_asy on x25_asy_open() failure.") Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Cong Wang authored
[ Upstream commit 7314f548 ] nr_find_socket(), nr_find_peer() and nr_find_listener() lock the sock after finding it in the global list. However, the call path requires BH disabled for the sock lock consistently. Actually the locking is unnecessary at this point, we can just hold the sock refcnt to make sure it is not gone after we unlock the global list, and lock it later only when needed. Reported-and-tested-by: syzbot+f621cda8b7e598908efa@syzkaller.appspotmail.com Signed-off-by:
-
Kunihiko Hayashi authored
[ Upstream commit 8742beb5 ] Even though the link is down before entering hibernation, there is an issue that the network interface always links up after resuming from hibernation. If the link is still down before enabling the network interface, and after resuming from hibernation, the phydev->state is forcibly set to PHY_UP in mdio_bus_phy_restore(), and the link becomes up. In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend() calls phy_stop_machine(), and mdio_bus_phy_resume() calls phy_start_machine(). In resume sequence, it's enough to do the same as mdio_bus_phy_resume() because the state has been preserved. This patch fixes the issue by calling phy_start_machine() in mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume(). Fixes: bc87922f ("phy: Move PHY PM operations into phy_device") Suggested-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by:
-
Claudiu Beznea authored
[ Upstream commit 42983885 ] On some platforms (currently detected only on SAMA5D4) TX might stuck even the pachets are still present in DMA memories and TX start was issued for them. This happens due to race condition between MACB driver updating next TX buffer descriptor to be used and IP reading the same descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted. GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt is asserted TX must be restarted. Restart TX if used bit is read and packets are present in software TX queue. Packets are removed from software TX queue if TX was successful for them (see macb_tx_interrupt()). Signed-off-by:
Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
-
Michal Kubecek authored
[ Upstream commit ade44640 ] Since commit 7969e5c4 ("ip: discard IPv4 datagrams with overlapping segments.") IPv4 reassembly code drops the whole queue whenever an overlapping fragment is received. However, the test is written in a way which detects duplicate fragments as overlapping so that in environments with many duplicate packets, fragmented packets may be undeliverable. Add an extra test and for (potentially) duplicate fragment, only drop the new fragment rather than the whole queue. Only starting offset and length are checked, not the contents of the fragments as that would be too expensive. For similar reason, linear list ("run") of a rbtree node is not iterated, we only check if the new fragment is a subset of the interval covered by existing consecutive fragments. v2: instead of an exact check iterating through linear list of an rbtree node, only check if the new fragment is subset of the "run" (suggested by Eric Dumazet) Fixes: 7969e5c4 ("ip: discard IPv4 datagrams with overlapping segments.") Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit d63967e4 ] Since capi_ioctl() copies 64 bytes after calling capi20_get_manufacturer() we need to ensure to not leak information to user. BUG: KMSAN: kernel-infoleak in _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32 CPU: 0 PID: 11245 Comm: syz-executor633 Not tainted 4.20.0-rc7+ #2 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613 kmsan_internal_check_memory+0x9d4/0xb00 mm/kmsan/kmsan.c:704 kmsan_copy_to_user+0xab/0xc0 mm/kmsan/kmsan_hooks.c:601 _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32 capi_ioctl include/linux/uaccess.h:177 [inline] capi_unlocked_ioctl+0x1a0b/0x1bf0 drivers/isdn/capi/capi.c:939 do_vfs_ioctl+0xebd/0x2bf0 fs/ioctl.c:46 ksys_ioctl fs/ioctl.c:713 [inline] __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl+0x1da/0x270 fs/ioctl.c:718 __x64_sys_ioctl+0x4a/0x70 fs/ioctl.c:718 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x440019 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffdd4659fb8 EFLAGS: 00000213 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440019 RDX: 0000000020000080 RSI: 00000000c0044306 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 0000000000000000 R09: 00000000004002c8 R10: 0000000000000000 R11: 0000000000000213 R12: 00000000004018a0 R13: 0000000000401930 R14: 0000000000000000 R15: 0000000000000000 Local variable description: ----data.i@capi_unlocked_ioctl Variable was created at: capi_ioctl drivers/isdn/capi/capi.c:747 [inline] capi_unlocked_ioctl+0x82/0x1bf0 drivers/isdn/capi/capi.c:939 do_vfs_ioctl+0xebd/0x2bf0 fs/ioctl.c:46 Bytes 12-63 of 64 are uninitialized Memory access of size 64 starts at ffff88807ac5fce8 Data copied to user address 0000000020000080 Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit cbb49697 ] xfrm6_policy_check() might have re-allocated skb->head, we need to reload ipv6 header pointer. sysbot reported : BUG: KASAN: use-after-free in __ipv6_addr_type+0x302/0x32f net/ipv6/addrconf_core.c:40 Read of size 4 at addr ffff888191b8cb70 by task syz-executor2/1304 CPU: 0 PID: 1304 Comm: syz-executor2 Not tainted 4.20.0-rc7+ #356 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x244/0x39d lib/dump_stack.c:113 print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256 kasan_report_error mm/kasan/report.c:354 [inline] kasan_report.cold.8+0x242/0x309 mm/kasan/report.c:412 __asan_report_load4_noabort+0x14/0x20 mm/kasan/report.c:432 __ipv6_addr_type+0x302/0x32f net/ipv6/addrconf_core.c:40 ipv6_addr_type include/net/ipv6.h:403 [inline] ip6_tnl_get_cap+0x27/0x190 net/ipv6/ip6_tunnel.c:727 ip6_tnl_rcv_ctl+0xdb/0x2a0 net/ipv6/ip6_tunnel.c:757 vti6_rcv+0x336/0x8f3 net/ipv6/ip6_vti.c:321 xfrm6_ipcomp_rcv+0x1a5/0x3a0 net/ipv6/xfrm6_protocol.c:132 ip6_protocol_deliver_rcu+0x372/0x1940 net/ipv6/ip6_input.c:394 ip6_input_finish+0x84/0x170 net/ipv6/ip6_input.c:434 NF_HOOK include/linux/netfilter.h:289 [inline] ip6_input+0xe9/0x600 net/ipv6/ip6_input.c:443 IPVS: ftp: loaded support on port[0] = 21 ip6_mc_input+0x514/0x11c0 net/ipv6/ip6_input.c:537 dst_input include/net/dst.h:450 [inline] ip6_rcv_finish+0x17a/0x330 net/ipv6/ip6_input.c:76 NF_HOOK include/linux/netfilter.h:289 [inline] ipv6_rcv+0x115/0x640 net/ipv6/ip6_input.c:272 __netif_receive_skb_one_core+0x14d/0x200 net/core/dev.c:4973 __netif_receive_skb+0x2c/0x1e0 net/core/dev.c:5083 process_backlog+0x24e/0x7a0 net/core/dev.c:5923 napi_poll net/core/dev.c:6346 [inline] net_rx_action+0x7fa/0x19b0 net/core/dev.c:6412 __do_softirq+0x308/0xb7e kernel/softirq.c:292 do_softirq_own_stack+0x2a/0x40 arch/x86/entry/entry_64.S:1027 </IRQ> do_softirq.part.14+0x126/0x160 kernel/softirq.c:337 do_softirq+0x19/0x20 kernel/softirq.c:340 netif_rx_ni+0x521/0x860 net/core/dev.c:4569 dev_loopback_xmit+0x287/0x8c0 net/core/dev.c:3576 NF_HOOK include/linux/netfilter.h:289 [inline] ip6_finish_output2+0x193a/0x2930 net/ipv6/ip6_output.c:84 ip6_fragment+0x2b06/0x3850 net/ipv6/ip6_output.c:727 ip6_finish_output+0x6b7/0xc50 net/ipv6/ip6_output.c:152 NF_HOOK_COND include/linux/netfilter.h:278 [inline] ip6_output+0x232/0x9d0 net/ipv6/ip6_output.c:171 dst_output include/net/dst.h:444 [inline] ip6_local_out+0xc5/0x1b0 net/ipv6/output_core.c:176 ip6_send_skb+0xbc/0x340 net/ipv6/ip6_output.c:1727 ip6_push_pending_frames+0xc5/0xf0 net/ipv6/ip6_output.c:1747 rawv6_push_pending_frames net/ipv6/raw.c:615 [inline] rawv6_sendmsg+0x3a3e/0x4b40 net/ipv6/raw.c:945 kobject: 'queues' (0000000089e6eea2): kobject_add_internal: parent: 'tunl0', set: '<NULL>' kobject: 'queues' (0000000089e6eea2): kobject_uevent_env inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798 kobject: 'queues' (0000000089e6eea2): kobject_uevent_env: filter function caused the event to drop! sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg+0xd5/0x120 net/socket.c:631 sock_write_iter+0x35e/0x5c0 net/socket.c:900 call_write_iter include/linux/fs.h:1857 [inline] new_sync_write fs/read_write.c:474 [inline] __vfs_write+0x6b8/0x9f0 fs/read_write.c:487 kobject: 'rx-0' (00000000e2d902d9): kobject_add_internal: parent: 'queues', set: 'queues' kobject: 'rx-0' (00000000e2d902d9): kobject_uevent_env vfs_write+0x1fc/0x560 fs/read_write.c:549 ksys_write+0x101/0x260 fs/read_write.c:598 kobject: 'rx-0' (00000000e2d902d9): fill_kobj_path: path = '/devices/virtual/net/tunl0/queues/rx-0' __do_sys_write fs/read_write.c:610 [inline] __se_sys_write fs/read_write.c:607 [inline] __x64_sys_write+0x73/0xb0 fs/read_write.c:607 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290 kobject: 'tx-0' (00000000443b70ac): kobject_add_internal: parent: 'queues', set: 'queues' entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x457669 Code: fd b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f9bd200bc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457669 RDX: 000000000000058f RSI: 00000000200033c0 RDI: 0000000000000003 kobject: 'tx-0' (00000000443b70ac): kobject_uevent_env RBP: 000000000072bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9bd200c6d4 R13: 00000000004c2dcc R14: 00000000004da398 R15: 00000000ffffffff Allocated by task 1304: save_stack+0x43/0xd0 mm/kasan/kasan.c:448 set_track mm/kasan/kasan.c:460 [inline] kasan_kmalloc+0xc7/0xe0 mm/kasan/kasan.c:553 __do_kmalloc_node mm/slab.c:3684 [inline] __kmalloc_node_track_caller+0x50/0x70 mm/slab.c:3698 __kmalloc_reserve.isra.41+0x41/0xe0 net/core/skbuff.c:140 __alloc_skb+0x155/0x760 net/core/skbuff.c:208 kobject: 'tx-0' (00000000443b70ac): fill_kobj_path: path = '/devices/virtual/net/tunl0/queues/tx-0' alloc_skb include/linux/skbuff.h:1011 [inline] __ip6_append_data.isra.49+0x2f1a/0x3f50 net/ipv6/ip6_output.c:1450 ip6_append_data+0x1bc/0x2d0 net/ipv6/ip6_output.c:1619 rawv6_sendmsg+0x15ab/0x4b40 net/ipv6/raw.c:938 inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg+0xd5/0x120 net/socket.c:631 ___sys_sendmsg+0x7fd/0x930 net/socket.c:2116 __sys_sendmsg+0x11d/0x280 net/socket.c:2154 __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg net/socket.c:2161 [inline] __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2161 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe kobject: 'gre0' (00000000cb1b2d7b): kobject_add_internal: parent: 'net', set: 'devices' Freed by task 1304: save_stack+0x43/0xd0 mm/kasan/kasan.c:448 set_track mm/kasan/kasan.c:460 [inline] __kasan_slab_free+0x102/0x150 mm/kasan/kasan.c:521 kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528 __cache_free mm/slab.c:3498 [inline] kfree+0xcf/0x230 mm/slab.c:3817 skb_free_head+0x93/0xb0 net/core/skbuff.c:553 pskb_expand_head+0x3b2/0x10d0 net/core/skbuff.c:1498 __pskb_pull_tail+0x156/0x18a0 net/core/skbuff.c:1896 pskb_may_pull include/linux/skbuff.h:2188 [inline] _decode_session6+0xd11/0x14d0 net/ipv6/xfrm6_policy.c:150 __xfrm_decode_session+0x71/0x140 net/xfrm/xfrm_policy.c:3272 kobject: 'gre0' (00000000cb1b2d7b): kobject_uevent_env __xfrm_policy_check+0x380/0x2c40 net/xfrm/xfrm_policy.c:3322 __xfrm_policy_check2 include/net/xfrm.h:1170 [inline] xfrm_policy_check include/net/xfrm.h:1175 [inline] xfrm6_policy_check include/net/xfrm.h:1185 [inline] vti6_rcv+0x4bd/0x8f3 net/ipv6/ip6_vti.c:316 xfrm6_ipcomp_rcv+0x1a5/0x3a0 net/ipv6/xfrm6_protocol.c:132 ip6_protocol_deliver_rcu+0x372/0x1940 net/ipv6/ip6_input.c:394 ip6_input_finish+0x84/0x170 net/ipv6/ip6_input.c:434 NF_HOOK include/linux/netfilter.h:289 [inline] ip6_input+0xe9/0x600 net/ipv6/ip6_input.c:443 ip6_mc_input+0x514/0x11c0 net/ipv6/ip6_input.c:537 dst_input include/net/dst.h:450 [inline] ip6_rcv_finish+0x17a/0x330 net/ipv6/ip6_input.c:76 NF_HOOK include/linux/netfilter.h:289 [inline] ipv6_rcv+0x115/0x640 net/ipv6/ip6_input.c:272 __netif_receive_skb_one_core+0x14d/0x200 net/core/dev.c:4973 __netif_receive_skb+0x2c/0x1e0 net/core/dev.c:5083 process_backlog+0x24e/0x7a0 net/core/dev.c:5923 kobject: 'gre0' (00000000cb1b2d7b): fill_kobj_path: path = '/devices/virtual/net/gre0' napi_poll net/core/dev.c:6346 [inline] net_rx_action+0x7fa/0x19b0 net/core/dev.c:6412 __do_softirq+0x308/0xb7e kernel/softirq.c:292 The buggy address belongs to the object at ffff888191b8cac0 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 176 bytes inside of 512-byte region [ffff888191b8cac0, ffff888191b8ccc0) The buggy address belongs to the page: page:ffffea000646e300 count:1 mapcount:0 mapping:ffff8881da800940 index:0x0 flags: 0x2fffc0000000200(slab) raw: 02fffc0000000200 ffffea0006eaaa48 ffffea00065356c8 ffff8881da800940 raw: 0000000000000000 ffff888191b8c0c0 0000000100000006 0000000000000000 page dumped because: kasan: bad access detected kobject: 'queues' (000000005fd6226e): kobject_add_internal: parent: 'gre0', set: '<NULL>' Memory state around the buggy address: ffff888191b8ca00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888191b8ca80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb >ffff888191b8cb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff888191b8cb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888191b8cc00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: 0d3c703a ("ipv6: Cleanup IPv6 tunnel receive path") Fixes: ed1efb2a ("ipv6: Add support for IPsec virtual tunnel interfaces") Signed-off-by:
-
Cong Wang authored
[ Upstream commit fb242745 ] syzbot reported the use of uninitialized udp6_addr::sin6_scope_id. We can just set ::sin6_scope_id to zero, as tunnels are unlikely to use an IPv6 address that needs a scope id and there is no interface to bind in this context. For net-next, it looks different as we have cfg->bind_ifindex there so we can probably call ipv6_iface_scope_id(). Same for ::sin6_flowinfo, tunnels don't use it. Fixes: 8024e028 ("udp: Add udp_sock_create for UDP tunnels to open listener socket") Reported-by: syzbot+c56449ed3652e6720f30@syzkaller.appspotmail.com Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Willem de Bruijn authored
[ Upstream commit 40c3ff6d ] Packet sockets may call dev_header_parse with NULL daddr. Make lowpan_header_ops.create fail. Fixes: 87a93e4e ("ieee802154: change needed headroom/tailroom") Signed-off-by:
Willem de Bruijn <willemb@google.com> Acked-by:
Alexander Aring <aring@mojatatu.com> Signed-off-by:
-
Tyrel Datwyler authored
[ Upstream commit 756af9c6 ] Commit 33a48ab1 ("ibmveth: Fix DMA unmap error") fixed an issue in the normal code path of ibmveth_xmit_start() that was originally introduced by Commit 6e8ab30e ("ibmveth: Add scatter-gather support"). This original fix missed the error path where dma_unmap_page is wrongly called on the header portion in descs[0] which was mapped with dma_map_single. As a result a failure to DMA map any of the frags results in a dmesg warning when CONFIG_DMA_API_DEBUG is enabled. ------------[ cut here ]------------ DMA-API: ibmveth 30000002: device driver frees DMA memory with wrong function [device address=0x000000000a430000] [size=172 bytes] [mapped as page] [unmapped as single] WARNING: CPU: 1 PID: 8426 at kernel/dma/debug.c:1085 check_unmap+0x4fc/0xe10 ... <snip> ... DMA-API: Mapped at: ibmveth_start_xmit+0x30c/0xb60 dev_hard_start_xmit+0x100/0x450 sch_direct_xmit+0x224/0x490 __qdisc_run+0x20c/0x980 __dev_queue_xmit+0x1bc/0xf20 This fixes the API misuse by unampping descs[0] with dma_unmap_single. Fixes: 6e8ab30e ("ibmveth: Add scatter-gather support") Signed-off-by:
Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by:
-
Lorenzo Bianconi authored
[ Upstream commit 8e1da73a ] Add napi_disable routine in gro_cells_destroy since starting from commit c42858ea ("gro_cells: remove spinlock protecting receive queues") gro_cell_poll and gro_cells_destroy can run concurrently on napi_skbs list producing a kernel Oops if the tunnel interface is removed while gro_cell_poll is running. The following Oops has been triggered removing a vxlan device while the interface is receiving traffic [ 5628.948853] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 [ 5628.949981] PGD 0 P4D 0 [ 5628.950308] Oops: 0002 [#1] SMP PTI [ 5628.950748] CPU: 0 PID: 9 Comm: ksoftirqd/0 Not tainted 4.20.0-rc6+ #41 [ 5628.952940] RIP: 0010:gro_cell_poll+0x49/0x80 [ 5628.955615] RSP: 0018:ffffc9000004fdd8 EFLAGS: 00010202 [ 5628.956250] RAX: 0000000000000000 RBX: ffffe8ffffc08150 RCX: 0000000000000000 [ 5628.957102] RDX: 0000000000000000 RSI: ffff88802356bf00 RDI: ffffe8ffffc08150 [ 5628.957940] RBP: 0000000000000026 R08: 0000000000000000 R09: 0000000000000000 [ 5628.958803] R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000040 [ 5628.959661] R13: ffffe8ffffc08100 R14: 0000000000000000 R15: 0000000000000040 [ 5628.960682] FS: 0000000000000000(0000) GS:ffff88803ea00000(0000) knlGS:0000000000000000 [ 5628.961616] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5628.962359] CR2: 0000000000000008 CR3: 000000000221c000 CR4: 00000000000006b0 [ 5628.963188] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 5628.964034] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 5628.964871] Call Trace: [ 5628.965179] net_rx_action+0xf0/0x380 [ 5628.965637] __do_softirq+0xc7/0x431 [ 5628.966510] run_ksoftirqd+0x24/0x30 [ 5628.966957] smpboot_thread_fn+0xc5/0x160 [ 5628.967436] kthread+0x113/0x130 [ 5628.968283] ret_from_fork+0x3a/0x50 [ 5628.968721] Modules linked in: [ 5628.969099] CR2: 0000000000000008 [ 5628.969510] ---[ end trace 9d9dedc7181661fe ]--- [ 5628.970073] RIP: 0010:gro_cell_poll+0x49/0x80 [ 5628.972965] RSP: 0018:ffffc9000004fdd8 EFLAGS: 00010202 [ 5628.973611] RAX: 0000000000000000 RBX: ffffe8ffffc08150 RCX: 0000000000000000 [ 5628.974504] RDX: 0000000000000000 RSI: ffff88802356bf00 RDI: ffffe8ffffc08150 [ 5628.975462] RBP: 0000000000000026 R08: 0000000000000000 R09: 0000000000000000 [ 5628.976413] R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000040 [ 5628.977375] R13: ffffe8ffffc08100 R14: 0000000000000000 R15: 0000000000000040 [ 5628.978296] FS: 0000000000000000(0000) GS:ffff88803ea00000(0000) knlGS:0000000000000000 [ 5628.979327] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5628.980044] CR2: 0000000000000008 CR3: 000000000221c000 CR4: 00000000000006b0 [ 5628.980929] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 5628.981736] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 5628.982409] Kernel panic - not syncing: Fatal exception in interrupt [ 5628.983307] Kernel Offset: disabled Fixes: c42858ea ("gro_cells: remove spinlock protecting receive queues") Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Acked-by:
-
Cong Wang authored
[ Upstream commit c4335704 ] There are multiple issues here: 1. After freeing dev->ax25_ptr, we need to set it to NULL otherwise we may use a dangling pointer. 2. There is a race between ax25_setsockopt() and device notifier as reported by syzbot. Close it by holding RTNL lock. 3. We need to test if dev->ax25_ptr is NULL before using it. Reported-and-tested-by: syzbot+ae6bb869cbed29b29040@syzkaller.appspotmail.com Signed-off-by:
-
Gustavo A. R. Silva authored
[ Upstream commit 69d2c867 ] vr.mifi is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: net/ipv6/ip6mr.c:1845 ip6mr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap) net/ipv6/ip6mr.c:1919 ip6mr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap) Fix this by sanitizing vr.mifi before using it to index mrt->vif_table' Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Gustavo A. R. Silva authored
[ Upstream commit 5648451e ] vr.vifi is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: net/ipv4/ipmr.c:1616 ipmr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap) net/ipv4/ipmr.c:1690 ipmr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap) Fix this by sanitizing vr.vifi before using it to index mrt->vif_table' Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2Signed-off-by:
-
- 29 Dec, 2018 26 commits
-
-
Greg Kroah-Hartman authored
-
Gustavo A. R. Silva authored
commit 505b5240 upstream. nr is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: drivers/gpu/drm/drm_ioctl.c:805 drm_ioctl() warn: potential spectre issue 'dev->driver->ioctls' [r] drivers/gpu/drm/drm_ioctl.c:810 drm_ioctl() warn: potential spectre issue 'drm_ioctls' [r] (local cap) drivers/gpu/drm/drm_ioctl.c:892 drm_ioctl_flags() warn: potential spectre issue 'drm_ioctls' [r] (local cap) Fix this by sanitizing nr before using it to index dev->driver->ioctls and drm_ioctls. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20181220000015.GA18973@embeddedorSigned-off-by:
-
Ivan Delalande authored
commit ea5751cc upstream. proc_sys_lookup can fail with ENOMEM instead of ENOENT when the corresponding sysctl table is being unregistered. In our case we see this upon opening /proc/sys/net/*/conf files while network interfaces are being deleted, which confuses our configuration daemon. The problem was successfully reproduced and this fix tested on v4.9.122 and v4.20-rc6. v2: return ERR_PTRs in all cases when proc_sys_make_inode fails instead of mixing them with NULL. Thanks Al Viro for the feedback. Fixes: ace0c791 ("proc/sysctl: Don't grab i_lock under sysctl_lock.") Cc: stable@vger.kernel.org Signed-off-by:
Ivan Delalande <colona@arista.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Roman Gushchin authored
commit 68600f62 upstream. I've noticed, that dying memory cgroups are often pinned in memory by a single pagecache page. Even under moderate memory pressure they sometimes stayed in such state for a long time. That looked strange. My investigation showed that the problem is caused by applying the LRU pressure balancing math: scan = div64_u64(scan * fraction[lru], denominator), where denominator = fraction[anon] + fraction[file] + 1. Because fraction[lru] is always less than denominator, if the initial scan size is 1, the result is always 0. This means the last page is not scanned and has no chances to be reclaimed. Fix this by rounding up the result of the division. In practice this change significantly improves the speed of dying cgroups reclaim. [guro@fb.com: prevent double calculation of DIV64_U64_ROUND_UP() arguments] Link: http://lkml.kernel.org/r/20180829213311.GA13501@castle Link: http://lkml.kernel.org/r/20180827162621.30187-3-guro@fb.comSigned-off-by:
Roman Gushchin <guro@fb.com> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Rik van Riel <riel@surriel.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Richard Weinberger authored
commit e58725d5 upstream. UBIFS's recovery code strictly assumes that a deleted inode will never come back, therefore it removes all data which belongs to that inode as soon it faces an inode with link count 0 in the replay list. Before O_TMPFILE this assumption was perfectly fine. With O_TMPFILE it can lead to data loss upon a power-cut. Consider a journal with entries like: 0: inode X (nlink = 0) /* O_TMPFILE was created */ 1: data for inode X /* Someone writes to the temp file */ 2: inode X (nlink = 0) /* inode was changed, xattr, chmod, … */ 3: inode X (nlink = 1) /* inode was re-linked via linkat() */ Upon replay of entry #2 UBIFS will drop all data that belongs to inode X, this will lead to an empty file after mounting. As solution for this problem, scan the replay list for a re-link entry before dropping data. Fixes: 474b9370 ("ubifs: Implement O_TMPFILE") Cc: stable@vger.kernel.org # 4.9-4.18 Cc: Russell Senior <russell@personaltelco.net> Cc: Rafał Miłecki <zajec5@gmail.com> Reported-by:
Russell Senior <russell@personaltelco.net> Reported-by:
Rafał Miłecki <zajec5@gmail.com> Tested-by:
Rafał Miłecki <rafal@milecki.pl> Signed-off-by:
Richard Weinberger <richard@nod.at> [rmilecki: update ubifs_assert() calls to compile with 4.18 and older] Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Uwe Kleine-König authored
The relevant difference between prepare_message and config is that the former is run before the CS signal is asserted. So the polarity of the CLK line must be configured in prepare_message as an edge generated by config might already result in a latch of the MOSI line. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Mark Brown <broonie@kernel.org> [ukleinek: backport to v4.14.x] Signed-off-by:
-
Uwe Kleine-König authored
This is just preparatory work which allows to move some initialisation that currently is done in the per transfer hook .config to an earlier point in time in the next few patches. There is no change in behaviour introduced by this patch. Signed-off-by:
-
Ihab Zhaika authored
commit f108703c upstream. add few PCI ID'S for 9560, 9462, 9461 and killer series. Cc: stable@vger.kernel.org Signed-off-by:
Ihab Zhaika <ihab.zhaika@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit eca1e56c upstream. Old firmware versions don't support this command. Sending it to any firmware before -41.ucode will crash the firmware. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201975 Fixes: 66e83903 ("iwlwifi: fix wrong WGDS_WIFI_DATA_SIZE") CC: <stable@vger.kernel.org> #4.19+ Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Sergey Senozhatsky authored
commit c7c3f05e upstream. From printk()/serial console point of view panic() is special, because it may force CPU to re-enter printk() or/and serial console driver. Therefore, some of serial consoles drivers are re-entrant. E.g. 8250: serial8250_console_write() { if (port->sysrq) locked = 0; else if (oops_in_progress) locked = spin_trylock_irqsave(&port->lock, flags); else spin_lock_irqsave(&port->lock, flags); ... } panic() does set oops_in_progress via bust_spinlocks(1), so in theory we should be able to re-enter serial console driver from panic(): CPU0 <NMI> uart_console_write() serial8250_console_write() // if (oops_in_progress) // spin_trylock_irqsave() call_console_drivers() console_unlock() console_flush_on_panic() bust_spinlocks(1) // oops_in_progress++ panic() <NMI/> spin_lock_irqsave(&port->lock, flags) // spin_lock_irqsave() serial8250_console_write() call_console_drivers() console_unlock() printk() ... However, this does not happen and we deadlock in serial console on port->lock spinlock. And the problem is that console_flush_on_panic() called after bust_spinlocks(0): void panic(const char *fmt, ...) { bust_spinlocks(1); ... bust_spinlocks(0); console_flush_on_panic(); ... } bust_spinlocks(0) decrements oops_in_progress, so oops_in_progress can go back to zero. Thus even re-entrant console drivers will simply spin on port->lock spinlock. Given that port->lock may already be locked either by a stopped CPU, or by the very same CPU we execute panic() on (for instance, NMI panic() on printing CPU) the system deadlocks and does not reboot. Fix this by removing bust_spinlocks(0), so oops_in_progress is always set in panic() now and, thus, re-entrant console drivers will trylock the port->lock instead of spinning on it forever, when we call them from console_flush_on_panic(). Link: http://lkml.kernel.org/r/20181025101036.6823-1-sergey.senozhatsky@gmail.com Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Daniel Wang <wonderfly@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Cc: Jiri Slaby <jslaby@suse.com> Cc: Peter Feiner <pfeiner@google.com> Cc: linux-serial@vger.kernel.org Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by:
Petr Mladek <pmladek@suse.com> Signed-off-by:
-
Colin Ian King authored
commit 32043fa0 upstream. Currently the copy_to_user of data in the gentry struct is copying uninitiaized data in field _pad from the stack to userspace. Fix this by explicitly memset'ing gentry to zero, this also will zero any compiler added padding fields that may be in struct (currently there are none). Detected by CoverityScan, CID#200783 ("Uninitialized scalar variable") Fixes: b263b31e ("x86, mtrr: Use explicit sizing and padding for the 64-bit ioctls") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Tyler Hicks <tyhicks@canonical.com> Cc: security@kernel.org Link: https://lkml.kernel.org/r/20181218172956.1440-1-colin.king@canonical.comSigned-off-by:
-
Dexuan Cui authored
commit fc96df16 upstream. Before 98f4c651, we returned zeros for unopened channels. With 98f4c651, we started to return random on-stack values. We'd better return -EINVAL instead. Fixes: 98f4c651 ("hv: move ringbuffer bus attributes to dev_groups") Cc: stable@vger.kernel.org Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by:
Dexuan Cui <decui@microsoft.com> Signed-off-by:
-
Cfir Cohen authored
commit c2dd5146 upstream. nested_get_vmcs12_pages() processes the posted_intr address in vmcs12. It caches the kmap()ed page object and pointer, however, it doesn't handle errors correctly: it's possible to cache a valid pointer, then release the page and later dereference the dangling pointer. I was able to reproduce with the following steps: 1. Call vmlaunch with valid posted_intr_desc_addr but an invalid MSR_EFER. This causes nested_get_vmcs12_pages() to cache the kmap()ed pi_desc_page and pi_desc. Later the invalid EFER value fails check_vmentry_postreqs() which fails the first vmlaunch. 2. Call vmlanuch with a valid EFER but an invalid posted_intr_desc_addr (I set it to 2G - 0x80). The second time we call nested_get_vmcs12_pages pi_desc_page is unmapped and released and pi_desc_page is set to NULL (the "shouldn't happen" clause). Due to the invalid posted_intr_desc_addr, kvm_vcpu_gpa_to_page() fails and nested_get_vmcs12_pages() returns. It doesn't return an error value so vmlaunch proceeds. Note that at this time we have a dangling pointer in vmx->nested.pi_desc and POSTED_INTR_DESC_ADDR in L0's vmcs. 3. Issue an IPI in L2 guest code. This triggers a call to vmx_complete_nested_posted_interrupt() and pi_test_and_clear_on() which dereferences the dangling pointer. Vulnerable code requires nested and enable_apicv variables to be set to true. The host CPU must also support posted interrupts. Fixes: 5e2f30b7 "KVM: nVMX: get rid of nested_get_page()" Cc: stable@vger.kernel.org Reviewed-by:
Andy Honig <ahonig@google.com> Signed-off-by:
Cfir Cohen <cfir@google.com> Reviewed-by:
Liran Alon <liran.alon@oracle.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Eduardo Habkost authored
commit 0e1b869f upstream. Some guests OSes (including Windows 10) write to MSR 0xc001102c on some cases (possibly while trying to apply a CPU errata). Make KVM ignore reads and writes to that MSR, so the guest won't crash. The MSR is documented as "Execution Unit Configuration (EX_CFG)", at AMD's "BIOS and Kernel Developer's Guide (BKDG) for AMD Family 15h Models 00h-0Fh Processors". Cc: stable@vger.kernel.org Signed-off-by:
Eduardo Habkost <ehabkost@redhat.com> Signed-off-by:
-
Thomas Gleixner authored
commit 0e334db6 upstream. The signal delivery path of posix-timers can try to rearm the timer even if the interval is zero. That's handled for the common case (hrtimer) but not for alarm timers. In that case the forwarding function raises a division by zero exception. The handling for hrtimer based posix timers is wrong because it marks the timer as active despite the fact that it is stopped. Move the check from common_hrtimer_rearm() to posixtimer_rearm() to cure both issues. Reported-by: syzbot+9d38bedac9cc77b8ad5e@syzkaller.appspotmail.com Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Hans de Goede authored
commit e59f5e08 upstream. Commit 78d3a92e ("gpiolib-acpi: Register GpioInt ACPI event handlers from a late_initcall") deferred the entire acpi_gpiochip_request_interrupt call for each event resource. This means it also delays the gpiochip_request_own_desc(..., "ACPI:Event") call. This is a problem if some AML code reads the GPIO pin before we run the deferred acpi_gpiochip_request_interrupt, because in that case acpi_gpio_adr_space_handler() will already have called gpiochip_request_own_desc(..., "ACPI:OpRegion") causing the call from acpi_gpiochip_request_interrupt to fail with -EBUSY and we will fail to register an event handler. acpi_gpio_adr_space_handler is prepared for acpi_gpiochip_request_interrupt already having claimed the pin, but the other way around does not work. One example of a problem this causes, is the event handler for the OTG ID pin on a Prowise PT301 tablet not registering, keeping the port stuck in whatever mode it was in during boot and e.g. only allowing charging after a reboot. This commit fixes this by only deferring the request_irq call and the initial run of edge-triggered IRQs instead of deferring all of acpi_gpiochip_request_interrupt. Cc: stable@vger.kernel.org Fixes: 78d3a92e ("gpiolib-acpi: Register GpioInt ACPI event ...") Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Christophe Leroy authored
commit abf221d2 upstream. spi_read() and spi_write() require DMA-safe memory. When CONFIG_VMAP_STACK is selected, those functions cannot be used with buffers on stack. This patch replaces calls to spi_read() and spi_write() by spi_write_then_read() which doesn't require DMA-safe buffers. Fixes: 0c36ec31 ("gpio: gpio driver for max7301 SPI GPIO expander") Cc: <stable@vger.kernel.org> Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
-
Russell King authored
commit 0b479790 upstream. While booting with rootfs on MMC, the following warning is encountered on OMAP4430: omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536] This is because the DMA engine has a default maximum segment size of 64K but HSMMC sets: mmc->max_blk_size = 512; /* Block Length at max can be 1024 */ mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count; mmc->max_seg_size = mmc->max_req_size; which ends up telling the block layer that we support a maximum segment size of 65535*512, which exceeds the advertised DMA engine capabilities. Fix this by clamping the maximum segment size to the lower of the maximum request size and of the DMA engine device used for either DMA channel. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Ulf Hansson authored
commit e3ae3401 upstream. Some eMMCs from Micron have been reported to need ~800 ms timeout, while enabling the CACHE ctrl after running sudden power failure tests. The needed timeout is greater than what the card specifies as its generic CMD6 timeout, through the EXT_CSD register, hence the problem. Normally we would introduce a card quirk to extend the timeout for these specific Micron cards. However, due to the rather complicated debug process needed to find out the error, let's simply use a minimum timeout of 1600ms, the double of what has been reported, for all cards when enabling CACHE ctrl. Reported-by:
Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reported-by:
Andreas Dannenberg <dannenberg@ti.com> Reported-by:
Faiz Abbas <faiz_abbas@ti.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Ulf Hansson authored
commit ba9f39a7 upstream. In commit 5320226a ("mmc: core: Disable HPI for certain Hynix eMMC cards"), then intent was to prevent HPI from being used for some eMMC cards, which didn't properly support it. However, that went too far, as even BKOPS and CACHE ctrl became prevented. Let's restore those parts and allow BKOPS and CACHE ctrl even if HPI isn't supported. Fixes: 5320226a ("mmc: core: Disable HPI for certain Hynix eMMC cards") Cc: Pratibhasagar V <pratibha@codeaurora.org> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Ulf Hansson authored
commit a0741ba4 upstream. During a re-initialization of the eMMC card, we may fail to re-enable HPI. In these cases, that isn't properly reflected in the card->ext_csd.hpi_en bit, as it keeps being set. This may cause following attempts to use HPI, even if's not enabled. Let's fix this! Fixes: eb0d8f13 ("mmc: core: support HPI send command") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Jens Axboe authored
commit 61cce6f6 upstream. When boxes are run near (or to) OOM, we have a problem with the discard page allocation in sd. If we fail allocating the special page, we return busy, and it'll get retried. But since ordering is honored for dispatch requests, we can keep retrying this same IO and failing. Behind that IO could be requests that want to free memory, but they never get the chance. This means you get repeated spews of traces like this: [1201401.625972] Call Trace: [1201401.631748] dump_stack+0x4d/0x65 [1201401.639445] warn_alloc+0xec/0x190 [1201401.647335] __alloc_pages_slowpath+0xe84/0xf30 [1201401.657722] ? get_page_from_freelist+0x11b/0xb10 [1201401.668475] ? __alloc_pages_slowpath+0x2e/0xf30 [1201401.679054] __alloc_pages_nodemask+0x1f9/0x210 [1201401.689424] alloc_pages_current+0x8c/0x110 [1201401.699025] sd_setup_write_same16_cmnd+0x51/0x150 [1201401.709987] sd_init_command+0x49c/0xb70 [1201401.719029] scsi_setup_cmnd+0x9c/0x160 [1201401.727877] scsi_queue_rq+0x4d9/0x610 [1201401.736535] blk_mq_dispatch_rq_list+0x19a/0x360 [1201401.747113] blk_mq_sched_dispatch_requests+0xff/0x190 [1201401.758844] __blk_mq_run_hw_queue+0x95/0xa0 [1201401.768653] blk_mq_run_work_fn+0x2c/0x30 [1201401.777886] process_one_work+0x14b/0x400 [1201401.787119] worker_thread+0x4b/0x470 [1201401.795586] kthread+0x110/0x150 [1201401.803089] ? rescuer_thread+0x320/0x320 [1201401.812322] ? kthread_park+0x90/0x90 [1201401.820787] ? do_syscall_64+0x53/0x150 [1201401.829635] ret_from_fork+0x29/0x40 Ensure that the discard page allocation has a mempool backing, so we know we can make progress. Cc: stable@vger.kernel.org Signed-off-by:
Jens Axboe <axboe@kernel.dk> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Jörgen Storvist authored
commit 28a86092 upstream. Added USB serial option driver support for Telit LN940 series cellular modules. Covering both QMI and MBIM modes. usb-devices output (0x1900): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=1900 Rev=03.10 S: Manufacturer=Telit S: Product=Telit LN940 Mobile Broadband S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option usb-devices output (0x1901): T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 20 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1bc7 ProdID=1901 Rev=03.10 S: Manufacturer=Telit S: Product=Telit LN940 Mobile Broadband S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim Signed-off-by:
Jörgen Storvist <jorgen.storvist@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Jörgen Storvist authored
commit 30360224 upstream. Added USB serial option driver support for Fibocom NL668 series cellular modules. Reserved USB endpoints 4, 5 and 6 for network + ADB interfaces. usb-devices output (QMI mode) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1508 ProdID=1001 Rev=03.18 S: Manufacturer=Nodecom NL668 Modem S: Product=Nodecom NL668-CN Modem S: SerialNumber= C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) usb-devices output (ECM mode) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 17 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1508 ProdID=1001 Rev=03.18 S: Manufacturer=Nodecom NL668 Modem S: Product=Nodecom NL668-CN Modem S: SerialNumber= C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) Signed-off-by:
-
Jörgen Storvist authored
commit cc6730df upstream. Added USB serial option driver support for Simcom SIM7500/SIM7600 series cellular modules exposing MBIM interface (VID 0x1e0e,PID 0x9003) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9003 Rev=03.18 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 6 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim Signed-off-by:
-
Tore Anderson authored
commit d57ec3c8 upstream. The HP lt4132 is a rebranded Huawei ME906s-158 LTE modem. The interface with protocol 0x16 is "CDC ECM & NCM" according to the *.inf files included with the Windows driver. Attaching the option driver to it doesn't result in a /dev/ttyUSB* device being created, so I've excluded it. Note that it is also excluded for corresponding Huawei-branded devices, cf. commit d544db29 ("USB: support new huawei devices in option.c"). T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver=(none) I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option I: If#=0x6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 3 P: Vendor=03f0 ProdID=a31d Rev=01.02 S: Manufacturer=HP Inc. S: Product=HP lt4132 LTE/HSPA+ 4G Module S: SerialNumber=0123456789ABCDEF C: #Ifs= 3 Cfg#= 3 Atr=a0 MxPwr=2mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option Signed-off-by:
Tore Anderson <tore@fud.no> Cc: stable@vger.kernel.org [ johan: drop id defines ] Signed-off-by:
-
