Use the r8a7790 timer init function on Lager
to make sure the architected timer is started
regardless of boot loader setting.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Implement a SoC-specific timer init function for
r8a7790 that makes sure the architected timer
is started regardless of boot loader setting.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the GPIO I/O memory range to the r8a7790 PFC device.

This extra I/O memory range is needed when using the PFC
tables to drive both pin functions (using PINCTRL or
function GPIO for old code) and actual GPIO. The goal is
however to use a separate GPIO driver in the long run
and when that happens this extra I/O memory range can
be removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

MMCIF and SDHI1 share the same slot on mackerel. One of them is selected
by a jumper, which cannot be queried from software. Currently in software
one of the two interfaces is selected, depending whether or not the MMCIF
driver is enabled. This is not optimal, since the kernel has to be rebuilt
to switch from one interface to another. Still, so far there isn't a
better option. At least make this selection consistent.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

To unify with SDHI1 also use named IRQs for SDHI0. This also clarifies
which specific IRQs are used.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Both SDHI and MMCIF drivers can use the standard slot-gpio card-detection
functions. Switch mackerel to using them instead of platform callbacks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Both SDHI and MMCIF drivers ignore their OCR platform values, when
available voltages can be retrieved from regulators.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The SDHI driver doesn't care about platform resource order, explicit
resource numbering is redundant.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Lager base board support making use of 2 GiB of memory,
the r8a7790 SoC with the SCIF0 serial port and CA15 with
ARM architected timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add LAN9220 support to the APE6EVM board using C and DT.
At this point the PFC driver lacks DT bindings so to
configure the PFC we use PINCTRL in C board code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Start using the r8a73a4 PFC on the APE6EVM board
and configure the SCIFA0 console signals in the
PFC via PINCTRL.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

V3 of APE6EVM base board support making use of
1 GiB of memory, the SCIFA0 serial port and
ARM architected timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a DT node for the SMSC 9221 ethernet chip, found on kzm9g, to its
reference implementation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add basic Bock-W board support

More devices will be added on top of this patch after
PICNTRL and clock framework are in better shape.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Second round of Renesas ARM and SH based SoC pinmux updates for v3.10

Highlights:

* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC

This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10

This merge is made to supply run-time dependencies for the following
patches that will bea added on top:

ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support

Remove unused pull-up/down data from the r8a73a4 PFC code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Function GPIOs are not used anymore, and all code use the GPIO numbers
directly. Remove the GPIOs enumeration.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

All r8a73a4 platforms use the pinctrl API to control pin functions.
Function GPIOs are no longer needed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Remove IRQ pin function GPIOs that have been deprecated by the pinctrl
API.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Remove SCIF function GPIOs that have been deprecated by the pinctrl API.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The r8a73a4 board support will use the pinctrl API to control the
external IRQ pins so remove the unused function GPIOS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The r8a73a4 board support will use the pinctrl API to control the SCIF
pins, remove the corresponding unused function GPIOS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

V2 of PINCTRL support for r8a73a4 IRQC hardware
and in particular the external pins IRQ0 -> IRQ57.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add PINCTRL support for r8a73a4 SCIF ports SCIFA0->SCIFA1 and
SCIFB0->SCIFB3.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Implement pull-up/down support for r8a73a4 similar to the implementation
for sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

V2 of code to add GPIO -> IRQ mappings to the
PFC table for the r8a73a4 SoC. Requires the IRQs
to be mapped at a fixed location in Linux IRQ
space. The actual IRQs are not handled by the
PFC, instead IRQC is used on r8a73a4.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The r8a73a4 SoC has sparse GPIO numbers. Declare ranges for pin numbers
in the PFC SoC data. Pin numbers shall be used with the GPIO API from
this point on.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add initial PFC support for the r8a73a4 SoC.

At this point only GPIO interface is supported, move to newer interfaces
planned as incremental changes.

Original authors are Morimoto-san with help from Yoshii-san, thanks to
them for the heavy lifting. Adjusted by Magnus to work together with
updated code in drivers/pinctrl.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The output pixel clocks can be used without the input pixel clocks.
Split them in different groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

GPIOs are now handled by a separate driver, remove GPIO data from the
SoC information structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Move GPIOs handling from the PFC device to separate GPIO devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When a GPIO is handled by a separate driver the pinmux
gpio_set_direction() handler won't be called. The pin mux type then need
to be configured to GPIO at request time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Boards/platforms that register dedicated GPIO devices will not supply a
memory resource for GPIOs. Try to locate the GPIO memory resource at
initialization time, and skip registration of the gpiochip if the
resource can't be found.

This is a temporary modification to ease the transition to separate GPIO
drivers. It should be reverted when all boards and platforms will have
been moved.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When implemented as a separate IP block, GPIOs should be handled by a
separate driver. To make this possible GPIO support needs to be optional
in the sh-pfc driver.

If no GPIO data registers are supplied in the SoC information structure
skip registration of the gpiochip.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The target is to get rid of function GPIOs completely. To reach this,
make function GPIOs support optional by skipping the function GPIO chip
registration if no function GPIOS are defined in SoC data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The board has 3 LEDs connected to GPIOs. Add a led-gpio device to
support them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Register the GPIO pin range, and request and free GPIO pins using the
pinctrl API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch is V3 of a GPIO driver for the R-Car series of
SoCs from Renesas. This driver is designed to be reusable
between multiple SoCs that share the same basic building block,
but so far it has only been used on R-Car H1 (r8a7779).

Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on a single I/O memory
range and the 32 GPIOs are hooked up a single interrupt.

In the case of R-Car H1 either external IRQ pins or GPIOs
with interrupts can be used for on-board interupts. For
external IRQs 4 pins are supported, and in the case of GPIO
there are 202 GPIOS as 202 interrupts hooked up via 6 driver
instances and to the GIC and the Cortex-A9 Quad.

At this point this driver is interfacing as a regular
platform device driver. In the future DT support will be
submitted as an incremental feature patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Function GPIOs are not used anymore, and all code use the GPIO numbers
directly. Remove the GPIOs enumeration.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>