- 30 Nov, 2018 14 commits
-
-
hersen wu authored
[WHY] fbc is within the data path from memory to dce. while re-configure mc dmif, fbc should be enabled. otherwise, fbc may not be enabled properly. [HOW] before re-configure mc dmif, disable fbc, only after dmif re-configuration fully done, enable fbc again. Signed-off-by:
hersen wu <hersenxs.wu@amd.com> Reviewed-by:
Roman Li <Roman.Li@amd.com> Acked-by:
Leo Li <sunpeng.li@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Harmanprit Tatla authored
* Use provided infopacket in stream (if valid) instead of reconstructing in set_vendor_info_packet() * Use proper format for enums * Use dc info packet struct instead Signed-off-by:
Harmanprit Tatla <Harmanprit.Tatla@amd.com> Reviewed-by:
Anthony Koo <Anthony.Koo@amd.com> Acked-by:
Krunoslav Kovac <Krunoslav.Kovac@amd.com> Acked-by:
-
abdoulaye berthe authored
[Why] Failure to read Detailed Capabilities Info. [How] Read Detailed Capbilities Info 80h-08Fh. Signed-off-by:
abdoulaye berthe <abdoulaye.berthe@amd.com> Reviewed-by:
Wenjing Liu <Wenjing.Liu@amd.com> Acked-by:
-
Krunoslav Kovac authored
Use axis instead of axix Signed-off-by:
Aric Cyr <Aric.Cyr@amd.com> Acked-by:
-
Joshua Aberback authored
[Why] This patch is for use by dm, no need for it in dc. Signed-off-by:
Joshua Aberback <joshua.aberback@amd.com> Reviewed-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
-
David Francis authored
[Why] There are a lot of unintuitive parts of the dm-dc interface. It would help us if these were documented to provide a common understanding of what they are supposed to do [How] Most of this documentation is stubs, to be filled out more thoroughly by the experts Not every dm-accessible function and struct is mentioned. Simple functions like getters, setters, retain, release, create, destroy can be left unadorned. Signed-off-by:
David Francis <David.Francis@amd.com> Reviewed-by:
Harry Wentland <Harry.Wentland@amd.com> Acked-by:
-
Steven Chiu authored
Signed-off-by:
Steven Chiu <steven.chiu@amd.com> Reviewed-by:
Shahin Khayyer <Shahin.Khayyer@amd.com> Acked-by:
-
Yogesh Mohan Marimuthu authored
[why] When there are multiple aux transaction in parallel, it is sometime sporadically the aux transaction starts to continuously fail. The aux transaction was failing because the busy bit for the given gpio pin was always set. The busy bit was alway set because the programming sequence to read, modify and write busy bit was not atomic. Due to which when multiple threads are trying to modify the busy bits for their gpio pins in the same integer variable sometimes the busy bits integer variable is written with old data causing failure. [how] Instead of using individual bits to track gpio pins and grouping them to integers, one byte will be allcoated for each gpio pin. Now whenever a gpio pin needs to be set to mark being used, only writing a value of one to that byte is sufficient, other bytes are not impacted. Also no need to have atomicity with bytes unlike with bits. Signed-off-by:
Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com> Reviewed-by:
-
Christian König authored
Instead of delaying that to the first query. Otherwise we could try to use the SDMA for VM updates before the IB tests are done. Signed-off-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Chunming Zhou <david1.zhou@amd.com> Reviewed-by:
Junwei Zhang <Jerry.Zhang@amd.com> Signed-off-by:
-
Alex Deucher authored
Looks like it was missed when setting support was added. Reviewed-by:
-
Alex Deucher authored
They don't have a fan controller. Reviewed-by:
Evan Quan <evan.quan@amd.com> Signed-off-by:
-
Oak Zeng authored
When paging queue is enabled, it use the second page of doorbell. The AMDGPU_DOORBELL64_MAX_ASSIGNMENT definition assumes all the kernel doorbells are in the first page. So with paging queue enabled, the total kernel doorbell range should be original num_doorbell plus one page (0x400 in dword), not *2. Signed-off-by:
Oak Zeng <ozeng@amd.com> Reviewed-by:
-
Christian König authored
We need to set the NO_EVICT flag on the ghost object or otherwise we are adding it to the LRU. When it is added to the LRU we can run into a race between destroying and evicting it again. Signed-off-by:
-
Nicholas Kazlauskas authored
[Why] With scaling, underscan and abm changes we can end up calling commit_planes_to_stream in commit_tail. This call uses dm_state->context which can be NULL if the commit was a fast update. [How] Use dc_state instead since that can't be NULL unless the system ran out of memory. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108912 Fixes: e64abff2f133 ("drm/amd/display: Use private obj helpers for dm_atomic_state") Signed-off-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by:
-
- 29 Nov, 2018 2 commits
-
-
Jerry (Fangzhi) Zuo authored
Calculate preferred refresh rate only when preferred mode exists. Signed-off-by:
Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com> Reviewed-by:
Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by:
-
Roman Li authored
[Why] More than 4x4K didn't lightup on Vega20 due to low dcfclk value. Powerplay expects valid min requirement for dcfclk from DC. [How] Update min_dcfclock_khz based on min_engine_clock value. Reviewed-by:
Feifei Xu <Feifei.Xu@amd.com> Reviewed-by:
-
- 28 Nov, 2018 22 commits
-
-
Young Xiao authored
the type mem->start is unsigned long, so this can overflow on 32bit system, since the type addr is uint64_t. Reviewed-by:
Young Xiao <YangX92@hotmail.com> Signed-off-by:
-
Colin Ian King authored
There are spelling mistakes in PP_ASSERT_WITH_CODE messages, fix these. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Chris Wilson authored
As amd_uvd_resume() accesses the uvd ring, it must be initialised first or else we trigger errors like: [ 5.595963] [drm] Found UVD firmware Version: 1.87 Family ID: 17 [ 5.595969] [drm] PSP loading UVD firmware [ 5.596266] ------------[ cut here ]------------ [ 5.596268] ODEBUG: assert_init not available (active state 0) object type: timer_list hint: (null) [ 5.596285] WARNING: CPU: 0 PID: 507 at lib/debugobjects.c:329 debug_print_object+0x6a/0x80 [ 5.596286] Modules linked in: amdgpu(+) hid_logitech_hidpp(+) chash gpu_sched amd_iommu_v2 ttm drm_kms_helper crc32c_intel drm hid_sony ff_memless igb hid_logitech_dj nvme dca i2c_algo_bit nvme_core wmi pinctrl_amd uas usb_storage [ 5.596299] CPU: 0 PID: 507 Comm: systemd-udevd Tainted: G W 4.20.0-0.rc1.git4.1.fc30.x86_64 #1 [ 5.596301] Hardware name: System manufacturer System Product Name/ROG STRIX X470-I GAMING, BIOS 0901 07/23/2018 [ 5.596303] RIP: 0010:debug_print_object+0x6a/0x80 [ 5.596305] Code: 8b 43 10 83 c2 01 8b 4b 14 4c 89 e6 89 15 e6 82 b0 02 4c 8b 45 00 48 c7 c7 60 fd 34 a6 48 8b 14 c5 a0 da 08 a6 e8 6a 6a b8 ff <0f> 0b 5b 83 05 d0 45 3e 01 01 5d 41 5c c3 83 05 c5 45 3e 01 01 c3 [ 5.596306] RSP: 0018:ffffa02ac863f8c0 EFLAGS: 00010282 [ 5.596307] RAX: 0000000000000000 RBX: ffffa02ac863f8e0 RCX: 0000000000000006 [ 5.596308] RDX: 0000000000000007 RSI: ffff9160e9a7bfe8 RDI: ffff9160f91d6c60 [ 5.596310] RBP: ffffffffa6742740 R08: 0000000000000002 R09: 0000000000000000 [ 5.596311] R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffa634ff69 [ 5.596312] R13: 00000000000b79d0 R14: ffffffffa80f76d8 R15: 0000000000266000 [ 5.596313] FS: 00007f762abf7940(0000) GS:ffff9160f9000000(0000) knlGS:0000000000000000 [ 5.596314] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5.596315] CR2: 000055fdc593f000 CR3: 00000007e999c000 CR4: 00000000003406f0 [ 5.596317] Call Trace: [ 5.596321] debug_object_assert_init+0x14a/0x180 [ 5.596327] del_timer+0x2e/0x90 [ 5.596383] amdgpu_fence_process+0x47/0x100 [amdgpu] [ 5.596430] amdgpu_uvd_resume+0xf6/0x120 [amdgpu] [ 5.596475] uvd_v7_0_sw_init+0xe0/0x280 [amdgpu] [ 5.596523] amdgpu_device_init.cold.30+0xf97/0x14b6 [amdgpu] [ 5.596563] ? amdgpu_driver_load_kms+0x53/0x330 [amdgpu] [ 5.596604] amdgpu_driver_load_kms+0x86/0x330 [amdgpu] [ 5.596614] drm_dev_register+0x115/0x150 [drm] [ 5.596654] amdgpu_pci_probe+0xbd/0x120 [amdgpu] [ 5.596658] local_pci_probe+0x41/0x90 [ 5.596661] pci_device_probe+0x188/0x1a0 [ 5.596666] really_probe+0xf8/0x3b0 [ 5.596669] driver_probe_device+0xb3/0xf0 [ 5.596672] __driver_attach+0xe1/0x110 [ 5.596674] ? driver_probe_device+0xf0/0xf0 [ 5.596676] bus_for_each_dev+0x79/0xc0 [ 5.596679] bus_add_driver+0x155/0x230 [ 5.596681] ? 0xffffffffc07d9000 [ 5.596683] driver_register+0x6b/0xb0 [ 5.596685] ? 0xffffffffc07d9000 [ 5.596688] do_one_initcall+0x5d/0x2be [ 5.596691] ? rcu_read_lock_sched_held+0x79/0x80 [ 5.596693] ? kmem_cache_alloc_trace+0x264/0x290 [ 5.596695] ? do_init_module+0x22/0x210 [ 5.596698] do_init_module+0x5a/0x210 [ 5.596701] load_module+0x2137/0x2430 [ 5.596703] ? lockdep_hardirqs_on+0xed/0x180 [ 5.596714] ? __do_sys_init_module+0x150/0x1a0 [ 5.596715] __do_sys_init_module+0x150/0x1a0 [ 5.596722] do_syscall_64+0x60/0x1f0 [ 5.596725] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 5.596726] RIP: 0033:0x7f762b877dee [ 5.596728] Code: 48 8b 0d 9d 20 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 49 89 ca b8 af 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 6a 20 0c 00 f7 d8 64 89 01 48 [ 5.596729] RSP: 002b:00007ffc777b8558 EFLAGS: 00000246 ORIG_RAX: 00000000000000af [ 5.596730] RAX: ffffffffffffffda RBX: 000055fdc48da320 RCX: 00007f762b877dee [ 5.596731] RDX: 00007f762b9f284d RSI: 00000000006c5fc6 RDI: 000055fdc527a060 [ 5.596732] RBP: 00007f762b9f284d R08: 0000000000000003 R09: 0000000000000002 [ 5.596733] R10: 000055fdc48ad010 R11: 0000000000000246 R12: 000055fdc527a060 [ 5.596734] R13: 000055fdc48dca20 R14: 0000000000020000 R15: 0000000000000000 [ 5.596740] irq event stamp: 134618 [ 5.596743] hardirqs last enabled at (134617): [<ffffffffa513d52e>] console_unlock+0x45e/0x610 [ 5.596744] hardirqs last disabled at (134618): [<ffffffffa50037e8>] trace_hardirqs_off_thunk+0x1a/0x1c [ 5.596746] softirqs last enabled at (133146): [<ffffffffa5e00365>] __do_softirq+0x365/0x47c [ 5.596748] softirqs last disabled at (133139): [<ffffffffa50c64f9>] irq_exit+0x119/0x120 [ 5.596749] ---[ end trace eaee508abfebccdc ]--- Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108709Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Alex Deucher <alexdeucher@gmail.com> Signed-off-by:
-
Andrey Grodzovsky authored
For XGMI hive case do reset in steps where each step iterates over all devs in hive. This especially important for asic reset since all PSP FW in hive must come up within a limited time (around 1 sec) to properply negotiate the link. Do this by refactoring amdgpu_device_gpu_recover and amdgpu_device_reset into pre_asic_reset, asic_reset and post_asic_reset functions where is part is exectued for all the GPUs in the hive before going to the next step. v2: Update names for amdgpu_device_lock/unlock functions. v3: Introduce per hive locking to avoid multiple resets for GPUs in same hive. v4: Remove delayed_workqueue()/ttm_bo_unlock_delayed_workqueue() - they are copy & pasted over from radeon and on amdgpu there isn't any reason for that any more. Signed-off-by:Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by:
-
Andrey Grodzovsky authored
It's needed for device reset of entire hive. v3: Add per hive lock to allow avoiding duplicate resets triggered by multiple members of same hive. Expose amdgpu_hive_info instead of adding getter functions. Signed-off-by:
-
Andrey Grodzovsky authored
This is prep work for updating each PSP FW in hive after GPU reset. Split into build topology SW state and update each PSP FW in the hive. Save topology and count of XGMI devices for reuse. v2: Create seperate header for XGMI. Signed-off-by:
-
Nicholas Kazlauskas authored
Support for AMDGPU specific FreeSync properties and ioctls are dropped from amdgpu_dm in favor of supporting drm variable refresh rate properties. The notify_freesync and set_freesync_property functions are dropped from amdgpu_display_funcs. The drm vrr_capable property is now attached to any DP/HDMI connector. Its value is updated accordingly to the connector's FreeSync capabiltiy. The freesync_enable logic and ioctl control has has been dropped in favor of utilizing the vrr_enabled on the drm CRTC. This allows for more fine grained atomic control over which CRTCs should support variable refresh rate. To handle state changes for vrr_enabled it was easiest to drop the forced modeset on freesync_enabled change. This patch now performs the required stream updates when planes are flipped. This is done for a few reasons: (1) VRR stream updates can be done in the fast update path (2) amdgpu_dm_atomic_check would need to be hacked apart to check desired variable refresh state and capability before the CRTC disable pass. (3) Performing VRR stream updates on-flip is needed for enabling BTR support. VRR packets and timing adjustments are now tracked and compared to previous values sent to the hardware. Signed-off-by: -
Nicholas Kazlauskas authored
When variable refresh rate is active the hardware counter can return a position >= vtotal. This results in a vpos being returned from amdgpu_display_get_crtc_scanoutpos that's a positive value. The positive value indicates to the caller that the display is currently in scanout when the display is actually still in vblank. This is because the vfront porch duration is unknown with variable refresh active and will end when either a page flip occurs or the timeout specified by the driver/display is reached. The behavior of the amdgpu_display_get_crtc_scanoutpos remains the same when the position is below vtotal. When the position is above vtotal the function will return a value that is effectively -vbl_end, the size of the vback porch. The only caller affected by this change is the DRM helper for calculating vblank timestamps. This change corrects behavior for calculating the page flip timestamp from being the previous timestamp to the calculation to the next timestamp when position >= vtotal. Signed-off-by:
-
Nicholas Kazlauskas authored
These include the drm_connector 'vrr_capable' and the drm_crtc 'vrr_enabled' properties. Signed-off-by:
Pekka Paalanen <pekka.paalanen@collabora.com> Signed-off-by:
-
Nicholas Kazlauskas authored
This patch introduces the 'vrr_enabled' CRTC property to allow dynamic control over variable refresh rate support for a CRTC. This property should be treated like a content hint to the driver - if the hardware or driver is not capable of driving variable refresh timings then this is not considered an error. Capability for variable refresh rate support should be determined by querying the vrr_capable drm connector property. It is worth noting that while the property is intended for atomic use it isn't filtered from legacy userspace queries. This allows for Xorg userspace drivers to implement support. Signed-off-by:
-
Nicholas Kazlauskas authored
Modern display hardware is capable of supporting variable refresh rates. This patch introduces the "vrr_capable" property on the connector to allow userspace to query support for variable refresh rates. Atomic drivers should attach this property to connectors that are capable of driving variable refresh rates using drm_connector_attach_vrr_capable_property(). The value should be updated based on driver and hardware capability by using drm_connector_set_vrr_capable_property(). Signed-off-by:
Manasi Navare <manasi.d.navare@intel.com> Reviewed-by:
-
Oak Zeng authored
Move doorbell structures, enum definitions and helper functions from amdgpu.h to amdgpu_doorbell.h. No functional change Signed-off-by:
-
Oak Zeng authored
ASIC specific doorbell layout is used instead of enum definition Signed-off-by:
Felix Kuehling <Felix.Kuehling@amd.com> Suggested-by:
-
Oak Zeng authored
Also call functioin amdgpu_device_doorbell_init after amdgpu_device_ip_early_init because the former depends on the later to set up asic-specific init_doorbell_index function Signed-off-by:
-
Oak Zeng authored
This introduces new doorbell layout for vega20 and future asics v2: Use enum definition instead of hardcoded value Signed-off-by:
-
Oak Zeng authored
Initialize doorbell index for asics vi and cik v2: Use enum definition instead of hardcoded number Signed-off-by:
-
Oak Zeng authored
v2: Use enum definition instead of hardcoded value v3: Remove unused enum definition Signed-off-by:
-
Oak Zeng authored
This is preparation to move doorbell index initialization to amdgpu_asic_funcs Signed-off-by:
-
Oak Zeng authored
This is a preparation work to make reserved doorbell index per device, instead of using a global macro definition. By doing this, we can easily change doorbell layout for future ASICs while not affecting ASICs in production. Signed-off-by:
-
David Francis authored
The fallback code for getting default backlight caps was using the wrong variable name. Fix it. Fixes: https://lists.freedesktop.org/archives/dri-devel/2018-November/197752.htmlSigned-off-by:
-
Nicholas Kazlauskas authored
[Why] Two non-blocking commits in succession can result in a sequence where the same dc->current_state is queried for both commits. 1. 1st commit -> check -> commit -> swaps atomic state -> queues work 2. 2nd commit -> check -> commit -> swaps atomic state -> queues work 3. 1st commit work finishes The issue with this sequence is that the same dc->current_state is read in both atomic checks. If the first commit modifies streams or planes those will be missing from the dc->current_state for the second atomic check. This result in many stream and plane errors in atomic commit tail. [How] The driver still needs to track old to new state to determine if the commit in its current implementation. Updating the dc_state in atomic tail is wrong since the dc_state swap should be happening as part of drm_atomic_helper_swap_state *before* the worker queue kicks its work off. The simplest replacement for the subclassing (which doesn't properly manage the old to new atomic state swap) is to use the drm private object helpers. While some of the dc_state members could be merged into dm_crtc_state or dm_plane_state and copied over that way it is easier for now to just treat the whole dc_state structure as a single private object. This allows amdgpu_dm to drop the dc->current_state copy from within atomic check. It's replaced by a copy from the current atomic state which is propagated correctly for the sequence described above. Since access to the dm_state private object is now locked this should also fix issues that could arise if submitting non-blocking commits from different threads. Cc: Harry Wentland <harry.wentland@amd.com> Cc: Leo Li <sunpeng.li@amd.com> Signed-off-by:
-
Christian König authored
This reverts commit 0efd2d2f. It's still causing problems for V3D. v2: keep rearming the timeout. Signed-off-by:
-
- 26 Nov, 2018 2 commits
-
-
Colin Ian King authored
There is a spelling mistake in the module description text and a comment too, fix them. Also line break overly long comment. Signed-off-by:
-
Brajeswar Ghosh authored
Remove dce/dce_mem_input.h which is included more than once Signed-off-by:
Brajeswar Ghosh <brajeswar.linux@gmail.com> Signed-off-by:
-
