- 17 Jun, 2017 6 commits
-
-
Thomas Falcon authored
[ Upstream commit 28f4d165 ] When a vNIC client driver requests a faulty device setting, the server returns an acceptable value for the client to request. This 64 bit value was incorrectly being swapped as a 32 bit value, resulting in loss of data. This patch corrects that by using the 64 bit swap function. Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Falcon authored
[ Upstream commit 75224c93 ] Error reports received from firmware were not being converted from big endian values, leading to bogus error codes reported on little endian systems. Signed-off-by:
-
Christophe Leroy authored
commit da2f27e9 upstream. In commit 82de0be6 ("netfilter: Add helper array register/unregister functions"), struct nf_conntrack_helper sip[MAX_PORTS][4] was changed to sip[MAX_PORTS * 4], so the memory init should have been changed to memset(&sip[4 * i], 0, 4 * sizeof(sip[i])); But as the sip[] table is allocated in the BSS, it is already set to 0 Fixes: 82de0be6 ("netfilter: Add helper array register/unregister functions") Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Richard authored
commit 22322035 upstream. The code in block/partitions/msdos.c recognizes FreeBSD, OpenBSD and NetBSD partitions and does a reasonable job picking out OpenBSD and NetBSD UFS subpartitions. But for FreeBSD the subpartitions are always "bad". Kernel: <bsd:bad subpartition - ignored Though all 3 of these BSD systems use UFS as a file system, only FreeBSD uses relative start addresses in the subpartition declarations. The following patch fixes this for FreeBSD partitions and leaves the code for OpenBSD and NetBSD intact: Signed-off-by:
Richard Narron <comet.berkeley@gmail.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Imre Deak authored
commit 6ab92afc upstream. Since commit bac2a909 Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Date: Wed Jan 21 02:17:42 2015 +0100 PCI / PM: Avoid resuming PCI devices during system suspend PCI devices will default to allowing the system suspend complete optimization where devices are not woken up during system suspend if they were already runtime suspended. This however breaks the i915/HDA drivers for two reasons: - The i915 driver has system suspend specific steps that it needs to run, that bring the device to a different state than its runtime suspended state. - The HDA driver's suspend handler requires power that it will request from the i915 driver's power domain handler. This in turn requires the i915 driver to runtime resume itself, but this won't be possible if the suspend complete optimization is in effect: in this case the i915 runtime PM is disabled and trying to get an RPM reference returns -EACCESS. Solve this by requiring the PCI/PM core to resume the device during system suspend which in effect disables the suspend complete optimization. Regardless of the above commit the optimization stayed disabled for DRM devices until commit d14d2a84 Author: Lukas Wunner <lukas@wunner.de> Date: Wed Jun 8 12:49:29 2016 +0200 drm: Remove dev_pm_ops from drm_class so this patch is in practice a fix for this commit. Another reason for the bug staying hidden for so long is that the optimization for a device is disabled if it's disabled for any of its children devices. i915 may have a backlight device as its child which doesn't support runtime PM and so doesn't allow the optimization either. So if this backlight device got registered the bug stayed hidden. Credits to Marta, Tomi and David who enabled pstore logging, that caught one instance of this issue across a suspend/ resume-to-ram and Ville who rememberd that the optimization was enabled for some devices at one point. The first WARN triggered by the problem: [ 6250.746445] WARNING: CPU: 2 PID: 17384 at drivers/gpu/drm/i915/intel_runtime_pm.c:2846 intel_runtime_pm_get+0x6b/0xd0 [i915] [ 6250.746448] pm_runtime_get_sync() failed: -13 [ 6250.746451] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul snd_hda_codec_realtek snd_hda_codec_generic ghash_clmulni_intel e1000e snd_hda_codec snd_hwdep snd_hda_core ptp mei_me pps_core snd_pcm lpc_ich mei prime_ numbers i2c_hid i2c_designware_platform i2c_designware_core [last unloaded: i915] [ 6250.746512] CPU: 2 PID: 17384 Comm: kworker/u8:0 Tainted: G U W 4.11.0-rc5-CI-CI_DRM_334+ #1 [ 6250.746515] Hardware name: /NUC5i5RYB, BIOS RYBDWi35.86A.0362.2017.0118.0940 01/18/2017 [ 6250.746521] Workqueue: events_unbound async_run_entry_fn [ 6250.746525] Call Trace: [ 6250.746530] dump_stack+0x67/0x92 [ 6250.746536] __warn+0xc6/0xe0 [ 6250.746542] ? pci_restore_standard_config+0x40/0x40 [ 6250.746546] warn_slowpath_fmt+0x46/0x50 [ 6250.746553] ? __pm_runtime_resume+0x56/0x80 [ 6250.746584] intel_runtime_pm_get+0x6b/0xd0 [i915] [ 6250.746610] intel_display_power_get+0x1b/0x40 [i915] [ 6250.746646] i915_audio_component_get_power+0x15/0x20 [i915] [ 6250.746654] snd_hdac_display_power+0xc8/0x110 [snd_hda_core] [ 6250.746661] azx_runtime_resume+0x218/0x280 [snd_hda_intel] [ 6250.746667] pci_pm_runtime_resume+0x76/0xa0 [ 6250.746672] __rpm_callback+0xb4/0x1f0 [ 6250.746677] ? pci_restore_standard_config+0x40/0x40 [ 6250.746682] rpm_callback+0x1f/0x80 [ 6250.746686] ? pci_restore_standard_config+0x40/0x40 [ 6250.746690] rpm_resume+0x4ba/0x740 [ 6250.746698] __pm_runtime_resume+0x49/0x80 [ 6250.746703] pci_pm_suspend+0x57/0x140 [ 6250.746709] dpm_run_callback+0x6f/0x330 [ 6250.746713] ? pci_pm_freeze+0xe0/0xe0 [ 6250.746718] __device_suspend+0xf9/0x370 [ 6250.746724] ? dpm_watchdog_set+0x60/0x60 [ 6250.746730] async_suspend+0x1a/0x90 [ 6250.746735] async_run_entry_fn+0x34/0x160 [ 6250.746741] process_one_work+0x1f2/0x6d0 [ 6250.746749] worker_thread+0x49/0x4a0 [ 6250.746755] kthread+0x107/0x140 [ 6250.746759] ? process_one_work+0x6d0/0x6d0 [ 6250.746763] ? kthread_create_on_node+0x40/0x40 [ 6250.746768] ret_from_fork+0x2e/0x40 [ 6250.746778] ---[ end trace 102a62fd2160f5e6 ]--- v2: - Use the new pci_dev->needs_resume flag, to avoid any overhead during the ->pm_prepare hook. (Rafael) v3: - Update commit message to reference the actual regressing commit. (Lukas) v4: - Rebase on v4 of patch 1/2. Fixes: d14d2a84 ("drm: Remove dev_pm_ops from drm_class") References: https://bugs.freedesktop.org/show_bug.cgi?id=100378 References: https://bugs.freedesktop.org/show_bug.cgi?id=100770 Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Marta Lofstedt <marta.lofstedt@intel.com> Cc: David Weinehall <david.weinehall@linux.intel.com> Cc: Tomi Sarvela <tomi.p.sarvela@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Takashi Iwai <tiwai@suse.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: linux-pci@vger.kernel.org Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Reported-and-tested-by:
Marta Lofstedt <marta.lofstedt@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1493726649-32094-2-git-send-email-imre.deak@intel.com (cherry picked from commit adfdf85d) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Imre Deak authored
commit 4d071c32 upstream. Some drivers - like i915 - may not support the system suspend direct complete optimization due to differences in their runtime and system suspend sequence. Add a flag that when set resumes the device before calling the driver's system suspend handlers which effectively disables the optimization. Needed by a future patch fixing suspend/resume on i915. Suggested by Rafael. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: stable@vger.kernel.org (rebased on v4.8, added kernel version to commit message stable tag) Signed-off-by:
-
- 14 Jun, 2017 34 commits
-
-
Greg Kroah-Hartman authored
-
Pablo Neira Ayuso authored
commit d2df92e9 upstream. The existing code selects no next branch to be inspected when re-inserting an inactive element into the rb-tree, looping endlessly. This patch restricts the check for active elements to the EEXIST case only. Fixes: e701001e ("netfilter: nft_rbtree: allow adjacent intervals with dynamic updates") Reported-by:
Wolfgang Bumiller <w.bumiller@proxmox.com> Tested-by:
-
Rafael J. Wysocki authored
commit 4296f23e upstream. sugov_start() only initializes struct sugov_cpu per-CPU structures for shared policies, but it should do that for single-CPU policies too. That in particular makes the IO-wait boost mechanism work in the cases when cpufreq policies correspond to individual CPUs. Fixes: 21ca6d2c (cpufreq: schedutil: Add iowait boosting) Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
-
Viresh Kumar authored
commit 6c4f0fa6 upstream. cached_raw_freq applies to the entire cpufreq policy and not individual CPUs. Apart from wasting per-cpu memory, it is actually wrong to keep it in struct sugov_cpu as we may end up comparing next_freq with a stale cached_raw_freq of a random CPU. Move cached_raw_freq to struct sugov_policy. Fixes: 5cbea469 (cpufreq: schedutil: map raw required frequency to driver frequency) Signed-off-by:
-
Jani Nikula authored
commit bb1d1329 upstream. The main thing are the DDI ports. If there's a VBT that says there are no outputs, we should trust that, and not have semi-random defaults. Unfortunately, the defaults have resulted in some Chromebooks without VBT to rely on this behaviour, so we split out the defaults for the missing VBT case. Reviewed-by:
Manasi Navare <manasi.d.navare@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
commit 66578857 upstream. We don't use the error return for anything other than reporting and logging that there is no VBT. We can pull the logging in the function, and remove the error status return. Moreover, if we needed the information for something later on, we'd probably be better off storing the bit in dev_priv, and using it where it's needed, instead of using the error return. While at it, improve the comments. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Kees Cook authored
commit f5f893c5 upstream. Under SMAP/PAN/etc, we cannot write directly to userspace memory, so this rearranges the test bytes to get written through copy_to_user(). Additionally drops the bad copy_from_user() test that would trigger a memcpy() against userspace on failure. [arnd: the test module was added in 3.14, and this backported patch should apply cleanly on all version from 3.14 to 4.10. The original patch was in 4.11 on top of a context change I saw the bug triggered with kselftest on a 4.4.y stable kernel] Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Laura Abbott authored
commit 98562656 upstream. adjust_lowmem_bounds is responsible for setting up the boundary for lowmem/highmem. This needs to be setup before memblock reservations can occur. At the time memblock reservations can occur, memory can also be removed from the system. The lowmem/highmem boundary and end of memory may be affected by this but it is currently not recalculated. On some systems this may be harmless, on others this may result in incorrect ranges being passed to the main memory allocator. Correct this by recalculating the lowmem/highmem boundary after all reservations have been made. Tested-by:
Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by:
Laura Abbott <labbott@redhat.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Cc: Julien Grall <julien.grall@arm.com> Signed-off-by:
-
Laura Abbott authored
commit 374d446d upstream. The logic for sanity_check_meminfo has become difficult to follow. Clean up the code so it's more obvious what the code is actually trying to do. Additionally, meminfo is now removed so rename the function to better describe its purpose. Tested-by:
Nicolas Pitre <nico@linaro.org> Signed-off-by:
Laura Abbott <lauraa@codeaurora.org> Signed-off-by:
-
Kristina Martsenko authored
commit 276e9327 upstream. This backport has a minor difference from the upstream commit: it adds the asm-uaccess.h file, which is not present in 4.9, because 4.9 does not have commit b4b8664d ("arm64: don't pull uaccess.h into *.S"). Original patch description: When handling a data abort from EL0, we currently zero the top byte of the faulting address, as we assume the address is a TTBR0 address, which may contain a non-zero address tag. However, the address may be a TTBR1 address, in which case we should not zero the top byte. This patch fixes that. The effect is that the full TTBR1 address is passed to the task's signal handler (or printed out in the kernel log). When handling a data abort from EL1, we leave the faulting address intact, as we assume it's either a TTBR1 address or a TTBR0 address with tag 0x00. This is true as far as I'm aware, we don't seem to access a tagged TTBR0 address anywhere in the kernel. Regardless, it's easy to forget about address tags, and code added in the future may not always remember to remove tags from addresses before accessing them. So add tag handling to the EL1 data abort handler as well. This also makes it consistent with the EL0 data abort handler. Fixes: d50240a5 ("arm64: mm: permit use of tagged pointers at EL0") Reviewed-by:
Dave Martin <Dave.Martin@arm.com> Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Kristina Martsenko <kristina.martsenko@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Kristina Martsenko authored
commit 7dcd9dd8 upstream. This backport has a small difference from the upstream commit: - The address tag is removed in watchpoint_handler() instead of get_distance_from_watchpoint(), because 4.9 does not have commit fdfeff0f ("arm64: hw_breakpoint: Handle inexact watchpoint addresses"). Original patch description: When we take a watchpoint exception, the address that triggered the watchpoint is found in FAR_EL1. We compare it to the address of each configured watchpoint to see which one was hit. The configured watchpoint addresses are untagged, while the address in FAR_EL1 will have an address tag if the data access was done using a tagged address. The tag needs to be removed to compare the address to the watchpoints. Currently we don't remove it, and as a result can report the wrong watchpoint as being hit (specifically, always either the highest TTBR0 watchpoint or lowest TTBR1 watchpoint). This patch removes the tag. Fixes: d50240a5 ("arm64: mm: permit use of tagged pointers at EL0") Acked-by:
Mark Rutland <mark.rutland@arm.com> Acked-by:
-
Kristina Martsenko authored
commit 81cddd65 upstream. This backport has a minor difference from the upstream commit, as v4.9 did not yet have the refactoring done by commit 8b6e70fc ("arm64: traps: correctly handle MRS/MSR with XZR"). Original patch description: When we emulate userspace cache maintenance in the kernel, we can currently send the task a SIGSEGV even though the maintenance was done on a valid address. This happens if the address has a non-zero address tag, and happens to not be mapped in. When we get the address from a user register, we don't currently remove the address tag before performing cache maintenance on it. If the maintenance faults, we end up in either __do_page_fault, where find_vma can't find the VMA if the address has a tag, or in do_translation_fault, where the tagged address will appear to be above TASK_SIZE. In both cases, the address is not mapped in, and the task is sent a SIGSEGV. This patch removes the tag from the address before using it. With this patch, the fault is handled correctly, the address gets mapped in, and the cache maintenance succeeds. As a second bug, if cache maintenance (correctly) fails on an invalid tagged address, the address gets passed into arm64_notify_segfault, where find_vma fails to find the VMA due to the tag, and the wrong si_code may be sent as part of the siginfo_t of the segfault. With this patch, the correct si_code is sent. Fixes: 7dd01aef ("arm64: trap userspace "dc cvau" cache operation on errata-affected core") Acked-by:
-
Takatoshi Akiyama authored
commit 3c910176 upstream. This patch fixes an issue that kernel panic happens when DMA is enabled and we press enter key while the kernel booting on the serial console. * An interrupt may occur after sci_request_irq(). * DMA transfer area is initialized by setup_timer() in sci_request_dma() and used in interrupt. If an interrupt occurred between sci_request_irq() and setup_timer() in sci_request_dma(), DMA transfer area has not been initialized yet. So, this patch changes the order of sci_request_irq() and sci_request_dma(). Fixes: 73a19e4c ("serial: sh-sci: Add DMA support.") Signed-off-by:
Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com> [Shimoda changes the commit log] Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Julius Werner authored
commit 32829da5 upstream. A recent fix to /dev/mem prevents mappings from wrapping around the end of physical address space. However, the check was written in a way that also prevents a mapping reaching just up to the end of physical address space, which may be a valid use case (especially on 32-bit systems). This patch fixes it by checking the last mapped address (instead of the first address behind that) for overflow. Fixes: b299cde2 ("drivers: char: mem: Check for address space wraparound with mmap()") Reported-by:
Nico Huber <nico.h@gmx.de> Signed-off-by:
Julius Werner <jwerner@chromium.org> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 40da1b11 upstream. If a custom CPU target is specified and that one is not available _or_ can't be interrupted then the code returns to userland without dropping a lock as notices by lockdep: |echo 133 > /sys/devices/system/cpu/cpu7/hotplug/target | ================================================ | [ BUG: lock held when returning to user space! ] | ------------------------------------------------ | bash/503 is leaving the kernel with locks still held! | 1 lock held by bash/503: | #0: (device_hotplug_lock){+.+...}, at: [<ffffffff815b5650>] lock_device_hotplug_sysfs+0x10/0x40 So release the lock then. Fixes: 757c989b ("cpu/hotplug: Make target state writeable") Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170602142714.3ogo25f2wbq6fjpj@linutronix.deSigned-off-by:
-
Takashi Iwai authored
commit 4efda5f2 upstream. soc_cleanup_card_resources() call snd_card_free() at the last of its procedure. This turned out to lead to a use-after-free. PCM runtimes have been already removed via soc_remove_pcm_runtimes(), while it's dereferenced later in soc_pcm_free() called via snd_card_free(). The fix is simple: just move the snd_card_free() call to the beginning of the whole procedure. This also gives another benefit: it guarantees that all operations have been shut down before actually releasing the resources, which was racy until now. Reported-and-tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit ba3021b2 upstream. snd_timer_user_tselect() reallocates the queue buffer dynamically, but it forgot to reset its indices. Since the read may happen concurrently with ioctl and snd_timer_user_tselect() allocates the buffer via kmalloc(), this may lead to the leak of uninitialized kernel-space data, as spotted via KMSAN: BUG: KMSAN: use of unitialized memory in snd_timer_user_read+0x6c4/0xa10 CPU: 0 PID: 1037 Comm: probe Not tainted 4.11.0-rc5+ #2739 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 dump_stack+0x143/0x1b0 lib/dump_stack.c:52 kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:1007 kmsan_check_memory+0xc2/0x140 mm/kmsan/kmsan.c:1086 copy_to_user ./arch/x86/include/asm/uaccess.h:725 snd_timer_user_read+0x6c4/0xa10 sound/core/timer.c:2004 do_loop_readv_writev fs/read_write.c:716 __do_readv_writev+0x94c/0x1380 fs/read_write.c:864 do_readv_writev fs/read_write.c:894 vfs_readv fs/read_write.c:908 do_readv+0x52a/0x5d0 fs/read_write.c:934 SYSC_readv+0xb6/0xd0 fs/read_write.c:1021 SyS_readv+0x87/0xb0 fs/read_write.c:1018 This patch adds the missing reset of queue indices. Together with the previous fix for the ioctl/read race, we cover the whole problem. Reported-by:
Alexander Potapenko <glider@google.com> Tested-by:
-
Takashi Iwai authored
commit d11662f4 upstream. The read from ALSA timer device, the function snd_timer_user_tread(), may access to an uninitialized struct snd_timer_user fields when the read is concurrently performed while the ioctl like snd_timer_user_tselect() is invoked. We have already fixed the races among ioctls via a mutex, but we seem to have forgotten the race between read vs ioctl. This patch simply applies (more exactly extends the already applied range of) tu->ioctl_lock in snd_timer_user_tread() for closing the race window. Reported-by:
-
Ben Skeggs authored
commit b4e382ca upstream. Reusing the list_head for both is a bad idea. Callback execution is done with the lock dropped so that alarms can be rescheduled from the callback, which means that with some unfortunate timing, lists can get corrupted. The execution list should not require its own locking, the single function that uses it can only be called from a single context. Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Sinclair Yeh authored
commit 07678eca upstream. When vmw_gb_surface_define_ioctl() is called with an existing buffer, we end up returning an uninitialized variable in the backup_handle. The fix is to first initialize backup_handle to 0 just to be sure, and second, when a user-provided buffer is found, we will use the req->buffer_handle as the backup_handle. Reported-by:
Murray McAllister <murray.mcallister@insomniasec.com> Signed-off-by:
Sinclair Yeh <syeh@vmware.com> Reviewed-by:
Deepak Rawat <drawat@vmware.com> Signed-off-by:
-
Vladis Dronov authored
commit ee9c4e68 upstream. The 'req->mip_levels' parameter in vmw_gb_surface_define_ioctl() is a user-controlled 'uint32_t' value which is used as a loop count limit. This can lead to a kernel lockup and DoS. Add check for 'req->mip_levels'. References: https://bugzilla.redhat.com/show_bug.cgi?id=1437431Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Reviewed-by:
-
Dan Carpenter authored
commit f0c62e98 upstream. If vmalloc() fails then we need to a bit of cleanup before returning. Fixes: fb1d9738 ("drm/vmwgfx: Add DRM driver for VMware Virtual GPU") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
Jin Yao authored
commit cc1582c2 upstream. When doing sampling, for example: perf record -e cycles:u ... On workloads that do a lot of kernel entry/exits we see kernel samples, even though :u is specified. This is due to skid existing. This might be a security issue because it can leak kernel addresses even though kernel sampling support is disabled. The patch drops the kernel samples if exclude_kernel is specified. For example, test on Haswell desktop: perf record -e cycles:u <mgen> perf report --stdio Before patch applied: 99.77% mgen mgen [.] buf_read 0.20% mgen mgen [.] rand_buf_init 0.01% mgen [kernel.vmlinux] [k] apic_timer_interrupt 0.00% mgen mgen [.] last_free_elem 0.00% mgen libc-2.23.so [.] __random_r 0.00% mgen libc-2.23.so [.] _int_malloc 0.00% mgen mgen [.] rand_array_init 0.00% mgen [kernel.vmlinux] [k] page_fault 0.00% mgen libc-2.23.so [.] __random 0.00% mgen libc-2.23.so [.] __strcasestr 0.00% mgen ld-2.23.so [.] strcmp 0.00% mgen ld-2.23.so [.] _dl_start 0.00% mgen libc-2.23.so [.] sched_setaffinity@@GLIBC_2.3.4 0.00% mgen ld-2.23.so [.] _start We can see kernel symbols apic_timer_interrupt and page_fault. After patch applied: 99.79% mgen mgen [.] buf_read 0.19% mgen mgen [.] rand_buf_init 0.00% mgen libc-2.23.so [.] __random_r 0.00% mgen mgen [.] rand_array_init 0.00% mgen mgen [.] last_free_elem 0.00% mgen libc-2.23.so [.] vfprintf 0.00% mgen libc-2.23.so [.] rand 0.00% mgen libc-2.23.so [.] __random 0.00% mgen libc-2.23.so [.] _int_malloc 0.00% mgen libc-2.23.so [.] _IO_doallocbuf 0.00% mgen ld-2.23.so [.] do_lookup_x 0.00% mgen ld-2.23.so [.] open_verify.constprop.7 0.00% mgen ld-2.23.so [.] _dl_important_hwcaps 0.00% mgen libc-2.23.so [.] sched_setaffinity@@GLIBC_2.3.4 0.00% mgen ld-2.23.so [.] _start There are only userspace symbols. Signed-off-by:
Jin Yao <yao.jin@linux.intel.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: acme@kernel.org Cc: jolsa@kernel.org Cc: kan.liang@intel.com Cc: mark.rutland@arm.com Cc: will.deacon@arm.com Cc: yao.jin@intel.com Link: http://lkml.kernel.org/r/1495706947-3744-1-git-send-email-yao.jin@linux.intel.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Breno Leitao authored
commit 7f22ced4 upstream. Currently tsk->thread.load_tm is not initialized in the task creation and can contain garbage on a new task. This is an undesired behaviour, since it affects the timing to enable and disable the transactional memory laziness (disabling and enabling the MSR TM bit, which affects TM reclaim and recheckpoint in the scheduling process). Fixes: 5d176f75 ("powerpc: tm: Enable transactional memory (TM) lazily for userspace") Signed-off-by:
Breno Leitao <leitao@debian.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Breno Leitao authored
commit 1195892c upstream. Currently tsk->thread->load_vec and load_fp are not initialized during task creation, which can lead to garbage values in these variables (non-zero values). These variables will be checked later in restore_math() to validate if the FP and vector registers are being utilized. Since these values might be non-zero, the restore_math() will continue to save the FP and vectors even if they were never utilized by the userspace application. load_fp and load_vec counters will then overflow (they wrap at 255) and the FP and Altivec will be finally disabled, but before that condition is reached (counter overflow) several context switches will have restored FP and vector registers without need, causing a performance degradation. Fixes: 70fe3d98 ("powerpc: Restore FPU/VEC/VSX if previously used") Signed-off-by:
Gustavo Romero <gusbromero@gmail.com> Acked-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Michael Bringmann authored
commit dc421b20 upstream. When adding or removing memory, the aa_index (affinity value) for the memblock must also be converted to match the endianness of the rest of the 'ibm,dynamic-memory' property. Otherwise, subsequent retrieval of the attribute will likely lead to non-existent nodes, followed by using the default node in the code inappropriately. Fixes: 5f97b2a0 ("powerpc/pseries: Implement memory hotplug add in the kernel") Signed-off-by:
Michael Bringmann <mwb@linux.vnet.ibm.com> Signed-off-by:
-
Michael Ellerman authored
commit ba4a648f upstream. In commit 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"), we switched to the generic implementation of cpu_to_node(), which uses a percpu variable to hold the NUMA node for each CPU. Unfortunately we neglected to notice that we use cpu_to_node() in the allocation of our percpu areas, leading to a chicken and egg problem. In practice what happens is when we are setting up the percpu areas, cpu_to_node() reports that all CPUs are on node 0, so we allocate all percpu areas on node 0. This is visible in the dmesg output, as all pcpu allocs being in group 0: pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07 pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15 pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23 pcpu-alloc: [0] 24 25 26 27 [0] 28 29 30 31 pcpu-alloc: [0] 32 33 34 35 [0] 36 37 38 39 pcpu-alloc: [0] 40 41 42 43 [0] 44 45 46 47 To fix it we need an early_cpu_to_node() which can run prior to percpu being setup. We already have the numa_cpu_lookup_table we can use, so just plumb it in. With the patch dmesg output shows two groups, 0 and 1: pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07 pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15 pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23 pcpu-alloc: [1] 24 25 26 27 [1] 28 29 30 31 pcpu-alloc: [1] 32 33 34 35 [1] 36 37 38 39 pcpu-alloc: [1] 40 41 42 43 [1] 44 45 46 47 We can also check the data_offset in the paca of various CPUs, with the fix we see: CPU 0: data_offset = 0x0ffe8b0000 CPU 24: data_offset = 0x1ffe5b0000 And we can see from dmesg that CPU 24 has an allocation on node 1: node 0: [mem 0x0000000000000000-0x0000000fffffffff] node 1: [mem 0x0000001000000000-0x0000001fffffffff] Fixes: 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID") Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> Signed-off-by:
-
Christophe Leroy authored
commit 6f553912 upstream. of_mm_gpiochip_add_data() generates an oops for NULL pointer dereference. of_mm_gpiochip_add_data() calls mm_gc->save_regs() before setting the data, therefore ->save_regs() cannot use gpiochip_get_data() Fixes: 937daafc ("powerpc: simple-gpio: use gpiochip data pointer") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Joe Carnuccio authored
commit 74939a0b upstream. Signed-off-by:
Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Joe Carnuccio authored
commit 1d634965 upstream. Set bit (BIT_15) to send right ECHO payload information for Diagnostic Echo Test command. Signed-off-by:
-
Joe Carnuccio authored
commit ce6c668b upstream. Firmware dump allows for debugging customer issues. This patch fixes start/end pointer calculation to capture T262 template entry for dump tool. Signed-off-by:
-
Johannes Thumshirn authored
commit ddff7ed4 upstream. When pci_enable_device() or pci_enable_device_mem() fail in qla2x00_probe_one() we bail out but do a call to pci_disable_device(). This causes the dev_WARN_ON() in pci_disable_device() to trigger, as the device wasn't enabled previously. So instead of taking the 'probe_out' error path we can directly return *iff* one of the pci_enable_device() calls fails. Additionally rename the 'probe_out' goto label's name to the more descriptive 'disable_device'. Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Fixes: e315cd28 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring") Reviewed-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
Giridhar Malavali <giridhar.malavali@cavium.com> Signed-off-by:
-
Marc Zyngier authored
commit d6dbdd3c upstream. Under memory pressure, we start ageing pages, which amounts to parsing the page tables. Since we don't want to allocate any extra level, we pass NULL for our private allocation cache. Which means that stage2_get_pud() is allowed to fail. This results in the following splat: [ 1520.409577] Unable to handle kernel NULL pointer dereference at virtual address 00000008 [ 1520.417741] pgd = ffff810f52fef000 [ 1520.421201] [00000008] *pgd=0000010f636c5003, *pud=0000010f56f48003, *pmd=0000000000000000 [ 1520.429546] Internal error: Oops: 96000006 [#1] PREEMPT SMP [ 1520.435156] Modules linked in: [ 1520.438246] CPU: 15 PID: 53550 Comm: qemu-system-aar Tainted: G W 4.12.0-rc4-00027-g1885c397eaec #7205 [ 1520.448705] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB12A 10/26/2016 [ 1520.463726] task: ffff800ac5fb4e00 task.stack: ffff800ce04e0000 [ 1520.469666] PC is at stage2_get_pmd+0x34/0x110 [ 1520.474119] LR is at kvm_age_hva_handler+0x44/0xf0 [ 1520.478917] pc : [<ffff0000080b137c>] lr : [<ffff0000080b149c>] pstate: 40000145 [ 1520.486325] sp : ffff800ce04e33d0 [ 1520.489644] x29: ffff800ce04e33d0 x28: 0000000ffff40064 [ 1520.494967] x27: 0000ffff27e00000 x26: 0000000000000000 [ 1520.500289] x25: ffff81051ba65008 x24: 0000ffff40065000 [ 1520.505618] x23: 0000ffff40064000 x22: 0000000000000000 [ 1520.510947] x21: ffff810f52b20000 x20: 0000000000000000 [ 1520.516274] x19: 0000000058264000 x18: 0000000000000000 [ 1520.521603] x17: 0000ffffa6fe7438 x16: ffff000008278b70 [ 1520.526940] x15: 000028ccd8000000 x14: 0000000000000008 [ 1520.532264] x13: ffff7e0018298000 x12: 0000000000000002 [ 1520.537582] x11: ffff000009241b93 x10: 0000000000000940 [ 1520.542908] x9 : ffff0000092ef800 x8 : 0000000000000200 [ 1520.548229] x7 : ffff800ce04e36a8 x6 : 0000000000000000 [ 1520.553552] x5 : 0000000000000001 x4 : 0000000000000000 [ 1520.558873] x3 : 0000000000000000 x2 : 0000000000000008 [ 1520.571696] x1 : ffff000008fd5000 x0 : ffff0000080b149c [ 1520.577039] Process qemu-system-aar (pid: 53550, stack limit = 0xffff800ce04e0000) [...] [ 1521.510735] [<ffff0000080b137c>] stage2_get_pmd+0x34/0x110 [ 1521.516221] [<ffff0000080b149c>] kvm_age_hva_handler+0x44/0xf0 [ 1521.522054] [<ffff0000080b0610>] handle_hva_to_gpa+0xb8/0xe8 [ 1521.527716] [<ffff0000080b3434>] kvm_age_hva+0x44/0xf0 [ 1521.532854] [<ffff0000080a58b0>] kvm_mmu_notifier_clear_flush_young+0x70/0xc0 [ 1521.539992] [<ffff000008238378>] __mmu_notifier_clear_flush_young+0x88/0xd0 [ 1521.546958] [<ffff00000821eca0>] page_referenced_one+0xf0/0x188 [ 1521.552881] [<ffff00000821f36c>] rmap_walk_anon+0xec/0x250 [ 1521.558370] [<ffff000008220f78>] rmap_walk+0x78/0xa0 [ 1521.563337] [<ffff000008221104>] page_referenced+0x164/0x180 [ 1521.569002] [<ffff0000081f1af0>] shrink_active_list+0x178/0x3b8 [ 1521.574922] [<ffff0000081f2058>] shrink_node_memcg+0x328/0x600 [ 1521.580758] [<ffff0000081f23f4>] shrink_node+0xc4/0x328 [ 1521.585986] [<ffff0000081f2718>] do_try_to_free_pages+0xc0/0x340 [ 1521.592000] [<ffff0000081f2a64>] try_to_free_pages+0xcc/0x240 [...] The trivial fix is to handle this NULL pud value early, rather than dereferencing it blindly. Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Reviewed-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
-
Jeff Mahoney authored
commit 896533a7 upstream. If we fail to add the space_info kobject, we'll leak the memory for the percpu counter. Fixes: 6ab0a202 (btrfs: publish allocation data in sysfs) Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Reviewed-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
